Search Documents

By Leon McCulloch

WHEN clean iron and metallic zinc dust, protected from the air, are heated below the melting point of zinc, the iron takes on a coating that has excellent protective value. This coating is a brittle alloy of zinc and iron, and the process is called sherardizing. Although the zinc particles are covered with oxide and cannot touch the iron, an extremely small amount of the zinc vaporizes and the vapor, reaching the iron, alloys with it. Other zinc then vaporizes to replace that which has been removed from the atmosphere. This process continues indefinitely at a decreasing rate, for the coating already formed permits zinc to diffuse through-it to combine with the iron beneath. In this way, the coating grows outward from the surface of the iron, as the bark grows from a tree. The method of growth was clearly seen while sherardizing small cubes of cast iron, at about 450° C., in a small glass-stoppered bottle enclosed in a rotating drum. The dust contained about 3 per cent. iron, which prevented caking, and coatings 1/2 in. thick were grown in a few hours. After a heavy layer had been formed, the cubes were again: treated for a shorter time. The layer last formed was seen to lie next to the iron, instead of at the outer surface, showing that the growth was from the surface of the iron outward. The coatings split at the edges and corners, leaving the iron exposed there. Flakes of graphite from the iron were lifted upward and embedded in the coatings. The composition of sherardized coatings varies from the outer surface inward, as would be expected from the mode of growth. That is, the iron content increases slowly at first, then more rapidly as the iron is approached. At the surface the least amount of iron possible is 6 per cent., as the experiments described below have shown.

Jan 2, 1922

By J. Elmer Thomas

If 1929 witnessed a growing realization on the part of the oil industry that supply must be balanced against demand, 1930 proved conclusively that excessive inventories constitute a price depressant even with balanced conditions. Increased attention was certainly paid to economic considerations last year, and the achievement of holding daily crude production, with a constantly mounting potential, to levels 500,000 bbl. below the output of the summer before, deserves special mention. The ill-advised accumulation, however, of gasoline stocks, at least 10,000,000 bbl. larger than necessary, nullified the restraint exercised by the producers and finally necessitated drastic downward price revisions. An event of special significance was the appointment by the Federal Oil Conservation Board, last March, of a temporary Committee on Petroleum Economics that attempted a forecast of demand, an estimate of supply, and an allocation of the latter between the principal producing states. Thus for the first time was an economic program for an entire basic industry drafted by an independent body under the auspices of the Federal Government. The report was widely discussed and generally approved, but its schedules were not adopted by the refining division nor by oil producers in the State of Texas until too late to contribute to the industry's prosperity during 1930. If the restraint of November had been exercised in May a profitable year might have been the result: The gasoline price war in California during June, however, illustrated the point that even with a fairly sound statistical position insistent pressure to expand normal marketing outlets must result in losses to all concerned. The balanced program so painfully attained by producers must be maintained by refiners and distributors to be completely effective. Again in November the Federal Oil Conservation Board, acting on the request of the directors of the American Petroleum Institute, called its Committee on Petroleum Economics back into existence to prepare a new estimate for the next six months. An economic program adopted in advance of the winter period of accumulating inventories may aid this large and essential industry toward the profits to which it is entitled

Jan 1, 1931

CONTENTS PAGE CARMICHAEL, NORMAN, and KIDDIE, JOHN.-Development of Mine Transportation in Clifton-Morenci District. Discussed by Norman Carmichael, Charles Legrand, B. B. Gottsberger 1 BARER, THOMAS C.-Fresnillo - Glory-hole Mining Practice. Discussed by Charles A. Mitke, B. B. Gottsberger, E. R. Thomas, Enoch Perkins..: 3 BRADLEY, P. R.-Estimation of Ore Reserves and Mining Methods in Alaska Juneau Mine. Discussed by R. M. Raymond, A. H. Rogers, Enoch Perkins, H. G. Moulton 6 BIRCH, STEPHEN.-Geology and Mining Methods of the Kennecott and Beatson Mines. Discussed by R. M. Raymond, Alan M. Bateman, Enoch Perkins 8 LEES, CHARLES E.-Mining Methods and Costs at the Iron Cap Copper Co., Copper Hill, Ariz. Discussed by A. L. Walker, A. Neustaedter 10 BELL, CHARLES N. -Mining Methods of the Telluride District. Discussed by Charles S. Hurter 10 Development of Mine Transportation in Clifton-Morenci District Discussion of the paper of NORMAN CARMICHAEL and JOHN KIDDIE, presented at the New York Meeting, February, 1924, and issued, as. Paper No. 1310-M, with MINING AND METALLURGY, March, 1924. NORMAN CARMICHAEL.-We realized the objections too the gable-bottom car, but were almost forced to its adoption by the same reasons that caused us to retain the 20-in. gage. To use another car would have meant a vast number of changes, for our transportation system was quite extensive; all mine chutes and ore bins were arranged for that car. Had we been laying out, new works, many of our decisions would have been different. MEMBER.-If you were planning it now, would you not put in box bottom cars with a rotary dump? NORMAN CARMICHAEL.-We surely would. One objection to the gable-bottom car is the spill. No, matter how carefully the cars are kept up,: there is always leakage and spill. The cost of keeping and maintaining the cars in a good state of repair, so as to keep that loss at a minimum, is not necessary for a box-bottom car.

Jan 6, 1924

By K. G. Davis, P. Fryzuk

VALUES for the equilibrium distribution coefficient, ko, are required for solidification studies. The procedure generally adopted1-3 is to progressively solidify alloy rods over a range of growth rates, under conditions where a high degree of convective mixing is present in the melt. The measured effective distribution coefficients are plotted as a function of growth rate, and the extrapolated value at zero growth rate is taken to be the equilibrium ko. The method is limited by the experimental difficulty in obtaining steady growth rates less than approximately 10-4 cm per sec. Extrapolation from rates greater than this can lead to inaccuracy. In the present investigation, an alternative method for determining ko, previously used by the authors for the Ag-Sn system,' was applied to alloy of thallium in tin. Specimens were grown under conditions where convective mixing was absent, and experimental concentration-distance curves in the region of the initial transient were compared with curves calculated for trial values of ko. The ko which gave the best fit was taken as the correct value. To obtain the calculated curves, a value for the diffusion constant in the liquid near to the melting point was needed. This was determined by the capillary-reservoir method. Diffusion Constants. Details of the experimental procedure used by the authors in the capillary-reservoir technique have been described in previous papers,5'6 the only variation being in the use of Tl204, a ß emitter, as tracer, in contrast to previous work where ? emitters were used. The activity of a ß-emitting sample, as measured in a Geiger counter, is proportional to the surface area. To measure the concentration of thallium along the capillary after diffusion had taken place, the solidified capillary (1 mm diam) was cut into 2.5-mm lengths and each length compressed between parallel steel plates to form a disc approximately 5 mm in diam. The discs were placed in a flat-bottomed dish, covered by a thin lead shield with a central aperture, and counted in a 0 counter with fixed geometry. Each disc was etched lightly in a dilute solution of nitric and hydrochloric acids a short time before counting, to eliminate sur-

Jan 1, 1968

By James Douglas

Once—and fortunately only once—before this occasion, was it my sad duty to express the loss we had sustained in the death of an eminent member. Dr. T. Sterry Hunt* was a student of chemistry who, by his investigations into the properties of the elementary bodies, had assisted emineiltly in the progress of the technical arts, and, more than any American of his generation, had helped to lay the foundations of chemical geology. William Earl Dodge, whose death we deplore to-day, occupied a rank not les~ importaiit in the army of industrial workers

Jan 1, 1904

By AIME AIME

T HE year 1920 will be a memorable one in the history of the world's coal supply. The prices reached were the highest of modern times, and as usually happens at such a time, the quality of the output deteriorated. In the last two years of the war, the world's output had risen close to the pre-war level. After the armistice, however, the cessation of munitions manufacture and the delay in resumption of normal business curtailed the demand for coal. Industrial disputes both in Europe and America closed many mines late in 1919 and further reduced the supply. Thus when in 1920 the world set its face to work again and industrial activity was resumed where resumption was possible, consumers' reserves of fuel proved insufficient and an almost universal feeling of apprehension over the coal supply swept around the world. The reasons for this alarm-lately a thing of the past-become clear when the world's production in 1920 is cast up.

Jan 1, 1921

By V. Carlson, J. A. Rowe, E. O. Bennett

This report concerns the microbial flora found throughout the surface facilities of six water-injection systems in Texas and Oklahoma. Each system is described in detail and water quality data are presented when available. Pseudomonads and sulfate-reducers (Desulfovibrio) were the predominate organisms found in the systems. The genera Sphaerotilus, Bacillus, Achromobacter, Minococcus, Clostridium, Flavobacteriurn, and Sarcina were also isolated in significant numbers. Molds, iron bacteria, sulfur bacteria and soil bacteria were found less frequently in the systems. It is concluded that a complex microbiological flora exists in oilfield water-injection systems. A tendency for waters to deteriorate in passage through solid bed filters is also noted. INTRODUCTION The injection of water into a subsurface formation is often accompanied by numerous problems, the origin and nature of which are only partially understood. During the past few years, investigators have indicated that bacteria are involved in some of these problems even though very little specific information is available concerning this matter. It is surprising that investigators working on microbiological problems in water injection have never made a complete study of the flora of these systems. The logical course to pursue is that of identifying the microbial flora and then examining each organism individually and in combination with others to determine if they produce a particular problem. The objective of the present investigation is to identify the microbial flora in water-injection systems. In addition. the quality of the water in most of the systems was determined and some observations made on the extent to which passage through surface-handling facilities affects water quality. The information derived from this study can serve as a foundation for additional basic investigations. EXPERIMENTAL PROCEDURE The microbial flora of six water-injection systems were studied at 50 sampling points. These systems are experiencing problems which may be attributable to micro-organisms, and two were being treated with antimicrobial agents at the time of this study. The samples were obtained by inoculating 1.0 ml of the water onto the different media at the sampling point. The media used for primary isolation included nutrient agar, Strokes agar, M-10-E medium and semi-solid thioglycollate medium. The cultures were returned to the laboratory, incubated at 30°C until growth occured; then, pure cultures were obtained from individual colonies. The pure cultures were identified according to standardbacteriologica1 procedures. Those organisms not fitting identification criteria exactly, even though exhibiting close similarities to known species, are listed as unidentified organisms. Membrane filters were used to make water-quality tests at intervals before and after collection of the microbiological samples. The filter discs were 47 mm in diameter with a 0.45-micron particle-size retention, and the tests were done under closed conditions at 20) psi. Membrane flow rates are plotted as increasing filtrate volumes, and the total solids contents arcs given when available. An effort was made to sample at each place in a system where a change in environment occurred. In this manner, the effect of passage through filters, tanks, hay sections, etc., on the microbial flora and water quality could be observed. RESULTS SYSTEM A This waterflood system (Fig. 1) is about four years old and daily pumps approx&ately 110,000 bbl of oil-free sour water from a 3,700-ft deep reef. The

By Ulf S. Landergren

Diffusion coefficients and marker movements have been determined in brass using welded couples. Three different concentration ranges were employed at 750°C, while a fourth concentration range was measured at 500°, 600°, 700°, and 800°C. Marker displacements toward and porosity development in the high zinc side of the couple were observed in all cases. The results were interpreted as favoring a vacancy diffusion mechanism. IN the large amount of diffusion literature which has accumulated during the past half century, very few experimental data have been presented on body-centered-cubic metallic phases. The impressive combination of experimental and theoretical studies which has given the vacancy mechanism a fairly secure position as the preferred mechanism for most face-centered-cubic metals has no counterpart for body-centered-cubic phases, although the theoretical picture seems to be in a better state than the experimental work. The attempts to select diffusion mechanisms by the theoretical calculation of the activation energy for the various conceivable unit diffusion processes and the energy of formation of the type of lattice defect required have been based on models of two kinds. The first kind utilizes potential functions fitted for certain properties of pure crystalline copper; the second kind is fitted for sodium. The latter is an example of an open metal in which the metallic ion is small compared with interatomic distance,&apos; while the former is characteristic of the larger class of metals in which the ions have diameters about as large as the interatomic distance. brass should resemble copper in this fundamental property. It should be evident that results on the mechanism of diffusion obtained for one of these classes need not necessarily apply to the other. Huntington and Seitz, using a model of the copper type, showed that the activation energies to be expected for interstitial migration or a two-atom direct interchange were much higher than that for vacancy diffusion. Zener pointed out that a four-atom ring rotation would involve an activation energy considerably lower than the two unlikely mechanisms although still higher than the vacancy mechanism in the face-centered-cubic structure. Furthermore, he argued, the four-atom rotation would be relatively easier in a body-centered-cubic lattice and might be competitive with the vacancy mechanism. Paneth showed that a body-centered-cubic crystal-like sodium could form interstitial defects of special type, called a crowdion, by crowding an extra atom into < 111 > directions where the defects would affect a line of about eight atoms. The defect was constrained to move along the defining line. Unlike the face-centered-cubic case, therefore, the theoretical calculations for the body-centered-cubic mechanism do not provide a very clear-cut answer, and the absence of adequate experimental studies is the more serious. This investigation was undertaken for the purpose of obtaining useful information on diffusion in body-centered-cubic phases. brass was chosen for several reasons: 1—the phase field is sufficiently wide at high temperatures to permit the use of diffusion couples with adequate concentration ranges for satisfactory chemical analysis, 2-—thermodynamic activity data are available for the calculation of mobilities from diffusion coefficients, 3—the phase is as close to the theoretical model of the copper -type on which the calculations have been done as any body-centered-cubic metallic phase is likely to be. Measurements of the movements (if found) of inert markers during the diffusion process would indicate that a vacancy or Or mechanism played a major role in diffusion in brass. If no marker movement should be found, a ring mechanism would be indicated but not assured. Experimental Procedure The alloys used in these experiments, listed in Table I with analyses, were supplied by the Naval Research Laboratory. They were from ingots of 3x3 in. cross-section, heated to 760°C, reduced under a

Jan 1, 1957

By H. P. Greenwald

THIs paper brings forward a discussion that was prepared for the meeting of the Coal Division in Chicago in 1938.1 War in Europe less than a year after that meeting, followed by our defense preparations and entry into the conflict, caused general cessation of large-scale experimentation on the subject, and it is best to confine this paper to events in the United States during the five-year period since the preceding paper was written. The views of members of the Coal Division&apos;s Committee2 on Rock-dust-ing for 1943 were obtained before this paper was written and the manuscript was reviewed by them. Extent of Rock-dusting Statistics on the use of rock dust in the United States during the years 1930-1933, appearing on page 97 of Volume 139 of the Transactions are extended in Table I herein through the year 1941. The results through 1933 did not appear encouraging, but there has been improve-ment since that date. It has always been true that the larger operations were the ones that used rock dust. In 1941 only 10 per cent of the mines in the country used rock dust, but they produced 57 per cent of the coal, employed just under 50 per cent of the miners, and accounted for 52 per cent of the man-hours. Unfortunately, collection and compilation of these statistics are slow procedures, and figures dealing with the tremendous war expansion of the industry are not likely to be available for a year or more. In 1941 the five leading states in regard to percentage of man-hours worked in mines using rock dust were: Utah, 92.1; Wyoming, 79.3; Alabama, 77.4; New Mexico, 72.5; West Virginia, 65.3. The first four states were the same as in 1933, but West Virginia displaced Washington in fifth place. On the basis of pounds of rock dust used per ton of coal, the five leading states in

Jan 1, 1944

By H. P. Greenwald

THIs paper brings forward a discussion that was prepared for the meeting of the Coal Division in Chicago in 1938.1 War in Europe less than a year after that meeting, followed by our defense preparations and entry into the conflict, caused general cessation of large-scale experimentation on the subject, and it is best to confine this paper to events in the United States during the five-year period since the preceding paper was written. The views of members of the Coal Division&apos;s Committee2 on Rock-dust-ing for 1943 were obtained before this paper was written and the manuscript was reviewed by them. Extent of Rock-dusting Statistics on the use of rock dust in the United States during the years 1930-1933, appearing on page 97 of Volume 139 of the Transactions are extended in Table I herein through the year 1941. The results through 1933 did not appear encouraging, but there has been improve-ment since that date. It has always been true that the larger operations were the ones that used rock dust. In 1941 only 10 per cent of the mines in the country used rock dust, but they produced 57 per cent of the coal, employed just under 50 per cent of the miners, and accounted for 52 per cent of the man-hours. Unfortunately, collection and compilation of these statistics are slow procedures, and figures dealing with the tremendous war expansion of the industry are not likely to be available for a year or more. In 1941 the five leading states in regard to percentage of man-hours worked in mines using rock dust were: Utah, 92.1; Wyoming, 79.3; Alabama, 77.4; New Mexico, 72.5; West Virginia, 65.3. The first four states were the same as in 1933, but West Virginia displaced Washington in fifth place. On the basis of pounds of rock dust used per ton of coal, the five leading states in

Jan 1, 1944

By G. Sachs, Jr. Brown W. F., Ebert L. J.

It is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to &apos;the same strength level (i.e., the same tensile strength in a conventional tensile test). However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features—the high speed, the notch, and the bending—the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests. In an attempt to analyze the fundamental nature of this test, it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom. The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension. This triaxial stress state occurs at a point in the interior of the notch specimen. It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present. This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors. This is contrary to the behavior. of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1947

By Ebert L. J., G. Sachs, Jr. Brown W. F.

It is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to &apos;the same strength level (i.e., the same tensile strength in a conventional tensile test). However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features—the high speed, the notch, and the bending—the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests. In an attempt to analyze the fundamental nature of this test, it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom. The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension. This triaxial stress state occurs at a point in the interior of the notch specimen. It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present. This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors. This is contrary to the behavior. of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1947

By T. L. Joseph

THE committee appointed to investigate the application of oxygenated air to the blast&apos; furnace believes, after a careful study of the problem, that this enriched air will increase hearth temperature, tonnage, flexibility of operation, and quality of pig iron made, and that fuel consumption will be decreased. These improvements are supported by theoretical evidence; but a practical trial of the process is necessary to establish more definitely the magnitude of benefits realized. The commercial application, however, may profitably be preceded by a test on a smaller scale. A small furnace will, in general, respond to the enriched air in the same way as a commercial furnace and the magnitude of the benefits to be gained from varying additions of oxygen can be fairly well established at relatively little expense. A new experimental furnace, being built jointly by the Bureau of Mines and the University of Minnesota, at Minneapolis, will have a capacity of about 6 tons and will riot require more than 700 cu. ft. of natural air per minute. Its hearth is 36 in. in diameter and its height about 32 ft. Enough oxygen to enrich the blast to the extent recommended by the committee can be obtained from a small oxygen unit. It might even be cheaper to perform preliminary experiments with tanks of oxygen obtained from regular, dealers. A procedure in making the test that suggests itself is to start with operation on normal air; then to use blast, enriched in several steps. Systematic temperature measurements of the tuyeres, slag, and metal would reveal any changes in hearth temperature. When these changes become large enough, the burden may be gradually increased to just within the breaking point and the furnace brought back to normal, if possible, by the addition of oxygen. Such a test would show what might be expected in the way of a decrease in fuel consumption and the time taken to "straighten up" the furnace by means of oxygen. The new furnace at Minneapolis is so equipped that the furnace process can be observed from the stock line to the iron notch. We have been taking gas samples at various elevations in the furnace to study combustibility of the fuel and the reducing power of the gas. If either of these is affected by removing inert nitrogen, the change can easily be measured.

Jan 11, 1924

By J. M. Locke

Bruckner&apos;s revolving cylinders for roasting ores, etc., are now used at a number of the mills in Colorado and New Mexico, for the purpose of roasting and chloridizing silver ores, with highly satisfactory results, even from those cylinders of small size, erected before the many improvements of recent date. AS examples of the larger improved cylinders, reference can be made to those erected at the Tennessee Reduction Works, Silver City, Grant County, New Mexico, and those which were built, in 1871, at the celebrated Caribou Silver Mill and Mines, Colorado, a mining enterprise which has proved so satisfactory as to have been lately sold to a Holland company for an enormous amount. These cylinders, as now constructed by Messrs. Lane & Bodley, of Cincinnati,,Ohio, are shown in Plate 111, in which Fig. I is an elevation in perspective, Fig. 2 a longitudinal, and Fig. 3 a transverse section. Fig. 4 is a sketch of a mill, with Bruckner&apos;s cylinder. The exterior of the cylinder is a shell of boiler iron, 12 feet long by 5 feet 6 inches in diameter. The ends are partially closed with similar material, leaving in the centre a circular opening about 2 feet in diameter, bounded by a flange projecting several inches. Upon one side is placed an opening closed by a hinged door. Upon the outside of the cylinder are bolted three bands, as shown in Fig. 1, in which the section of the first is square, and that of the third semi- . circular; the second, or middle band, is a strong spur gear. Passing through the cylinder are six pipes parallel to one another, in a plane at an angle of 15" to the axis of the cylinder; these pipes also lie in this plane at an angle of from 30" to 35&apos; to the longitudinal .axis of the plane, as shown in Fig. 2, where the internal arrangement of the cylinder is seen, a perforated diaphragm being formed through part of the cylinder by means of perforated plates placed between

By Warren B. Weeks

Continued development in the deeper fields discovered during 1937 and 1938 was largely responsible for the 16 per cent (2,913,400-bbl.) increase in production, bringing the 1939 output to 21,376,230 bbl., the largest for South Arkansas since 1929. The older settled fields continued to decline and Rodessa was added to this classification. Magnolia field accounted for much of the increase, with Schuler field showing only a slight increase. There were 248 wells drilled during 1939, five more than during the previous year. Of 198 wells drilled in proven fields, 21 were dry; 46 of the 50 wildcats drilled were dry. The old depth record of 8332 ft. was increased to the present record of 9028. Trend of Prospecting Production from the porous " Reynolds " oolite zone of the Smackover limestone continued to be the objective of prospecting. During the year 20 seismograph, 3 gravity meter, 1 magnetometer, 1 soil analysis and 1 electromagnetic crews were reported in the state. The geophysical work was largely concentrated in three southern counties: Columbia, Lafayette and Union. As indicated in Table 2, the same three counties received most of the important drilling tests. At the end of the year only three seismograph crews remained in the areas. The area for prospecting Smackover limestone was greatly narrowed during the year by the failure of two "fault zone" wells to find satisfactory permeability in the oolite zone, and by the relatively thin sections of porosity found in wells drilled in townships 18 and 19 South. Geology Most of the wells listed in Table 2 afforded additional control on structure of the lower beds, but gave little new information on stratigraphy. Of the 248 wells drilled, 3 ended in Tertiary, 34 in Gulf, 1 in Paluxy, 29 in Glen Rose, 15 in Travis Peak, 15 in Cotton Valley, 139 in Smackover, 2 in Eagle Mills and 10 in Carboniferous. The age of the beds between the Travis Peak formation and Carboniferous is still questionable. Most

Jan 1, 1940

By Warren B. Weeks

Continued development in the deeper fields discovered during 1937 and 1938 was largely responsible for the 16 per cent (2,913,400-bbl.) increase in production, bringing the 1939 output to 21,376,230 bbl., the largest for South Arkansas since 1929. The older settled fields continued to decline and Rodessa was added to this classification. Magnolia field accounted for much of the increase, with Schuler field showing only a slight increase. There were 248 wells drilled during 1939, five more than during the previous year. Of 198 wells drilled in proven fields, 21 were dry; 46 of the 50 wildcats drilled were dry. The old depth record of 8332 ft. was increased to the present record of 9028. Trend of Prospecting Production from the porous " Reynolds " oolite zone of the Smackover limestone continued to be the objective of prospecting. During the year 20 seismograph, 3 gravity meter, 1 magnetometer, 1 soil analysis and 1 electromagnetic crews were reported in the state. The geophysical work was largely concentrated in three southern counties: Columbia, Lafayette and Union. As indicated in Table 2, the same three counties received most of the important drilling tests. At the end of the year only three seismograph crews remained in the areas. The area for prospecting Smackover limestone was greatly narrowed during the year by the failure of two "fault zone" wells to find satisfactory permeability in the oolite zone, and by the relatively thin sections of porosity found in wells drilled in townships 18 and 19 South. Geology Most of the wells listed in Table 2 afforded additional control on structure of the lower beds, but gave little new information on stratigraphy. Of the 248 wells drilled, 3 ended in Tertiary, 34 in Gulf, 1 in Paluxy, 29 in Glen Rose, 15 in Travis Peak, 15 in Cotton Valley, 139 in Smackover, 2 in Eagle Mills and 10 in Carboniferous. The age of the beds between the Travis Peak formation and Carboniferous is still questionable. Most

Jan 1, 1940

By W. A. Bruce

This paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown Whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to well-spacing problems are shown. Introduction The pressure-prediction methods to be described here are based upon the conception of an oil pool as a small part of a large porous continuum, containing for the most part water. The formation containing this water may be thought of as extending over an area of many square miles and having one or more small bodies of oil or gas trapped in high spots or reservoirs. It will be treated as having the genera1 aspect of a thin, flat sheet with an over-all tilt to the horizontal and with numerous small high spots, tight zones, and irregularities This porous continuum will be treated as being much more extensive than the oil or gas zones, but will be recognized as terminating at such large boundaries as a general fault, outcrop, unconformity, or pinch-out. Throughout the greater part of this limited porous continuum it is likely that there is a hydraulic connection. If this is true, the removal of fluid in one place will cause a disturbance that eventually will travel to all parts of the continuum. This picture has led to the recognition of water as the major fluid in the porous continuum and in many cases the expansive nature of this water as the main driving force producing the oil. The next step is the solution of the general problem of compressible liquid behavior in porous media. The works of Hurst I and Muskat2 introduced the idea of using heat-flow mathematics to consider the problem of compressible liquid flow in a porous medium. Before their reports, it had been thought sufficient to use the incompressible fluid-flow work of S1ichter.3 Law Muskat4 pointed out in detail how far the incompressible-fluirl assumption, deviated from fact even for water, of which the compressibility is about 3 X 10-6 volumes per unit volume per pound per square inch. He showed that this deviation increased with increases of distance. For example, the incompressible-fluid formula might show good agreement with the

Jan 1, 1943

By W. A. Bruce

This paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown Whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to well-spacing problems are shown. Introduction The pressure-prediction methods to be described here are based upon the conception of an oil pool as a small part of a large porous continuum, containing for the most part water. The formation containing this water may be thought of as extending over an area of many square miles and having one or more small bodies of oil or gas trapped in high spots or reservoirs. It will be treated as having the genera1 aspect of a thin, flat sheet with an over-all tilt to the horizontal and with numerous small high spots, tight zones, and irregularities This porous continuum will be treated as being much more extensive than the oil or gas zones, but will be recognized as terminating at such large boundaries as a general fault, outcrop, unconformity, or pinch-out. Throughout the greater part of this limited porous continuum it is likely that there is a hydraulic connection. If this is true, the removal of fluid in one place will cause a disturbance that eventually will travel to all parts of the continuum. This picture has led to the recognition of water as the major fluid in the porous continuum and in many cases the expansive nature of this water as the main driving force producing the oil. The next step is the solution of the general problem of compressible liquid behavior in porous media. The works of Hurst I and Muskat2 introduced the idea of using heat-flow mathematics to consider the problem of compressible liquid flow in a porous medium. Before their reports, it had been thought sufficient to use the incompressible fluid-flow work of S1ichter.3 Law Muskat4 pointed out in detail how far the incompressible-fluirl assumption, deviated from fact even for water, of which the compressibility is about 3 X 10-6 volumes per unit volume per pound per square inch. He showed that this deviation increased with increases of distance. For example, the incompressible-fluid formula might show good agreement with the

Jan 1, 1943

By W. H. Ashby, R. W. Cassingham, C. R. Blomberg, J. B. Justins

The Brookhaven field is one of several Basal Tuscaloosa reservoirs located in south-central Mississippi. It is a standstone reservoir, of erratic deposition and with several faults, having an approximate subsea depth of 9,800 ft. A large variation in permeability exists with a weighted average being 256 md. Estimated average interstitial water saturation is 45 per cent. The undersaturated reservoir fluid exhibits marked differences in physical properties with measured saturation pressures ranging from 733 to 2,255 psi. Early rapid decline in reservoir pressure caused the operating interests to unitize the field and initiate a program of pressure maintenance by gas injection. At the time gas injection was commenced, the reservoir pressure had fallen to nearly half of the original pressure with only 4.5 Per cent of the original oil in place produced. The reservoir pressure has since been maintained at approximately 2,750 psig, and cumulative production to date is 17 per cent of original oil in place. An analysis of field performance during gas injection is presented in detail. The program of pressure maintenance by gas injection is considered to be a success, since the expected ultimate recovery has been increased and the current production rate is in excess of 2 per cent of original oil in place per year. Performance has been better, anticipated ultimate recovery is larger, and total production costs are lower than for a similar Basal Tuscaloosa reservoir nearby, even though that field appears to have a more effective natural water drive. INTRODUCTION The history of the Brookhaven Unit is a testimonial for unitization and for the application of engineering techniques in the operation of an oil field. The operating and royalty interests in this field have mutually benefited from their early recognition of the need for unitization and pressure maintenance and from the forthright manner in which these were accomplished. The tangible benefits accruing to the participants in the Unit are: (1) income from gasoline plant products, (2) reduced lifting and operating costs from those of competitive operation, (3) maintenance of high levels of current income by mitigation of the inevitable decline in production rates inherent to natural depletion, (4) an increase in ultimate recovery of about 40 per cent over natural depletion operations. This paper should properly be considered a progress report; however, the performance of the field after five years of pressure maintenance clearly indicates that the ultimate success of the project is assured. LOCATION AND GEOLOGY The Brookhaven field is located in south-central Mississippi, about six miles from the town of Brookhaven. Production at Brookhaven

Jan 1, 1955

By William Kent

I DESIRE to place on record in our Transactions a recent innovation in blast-furnace practice, namely, the introduction at the Lucy Furnaces, in Pittsburgh, of four water-tube steam-boilers, of the Babcock and Wilcox pattern, aggregating 832 horse-power, builder&apos;s rating, or 9,568 square feet of heating-surface, utilizing the waste gases of the furnaces as fuel. The boilers are set in two batteries, each of 416 horse-power, and each battery occupying a ground-space of 22 feet 7 inches by 20 feet 4 inches. The accompanying dram-

Jan 1, 1885