Search Documents

By K. Tangri, M. Chaturvedi

The addition of 0.5 wt pct Cu to Zr-2.5 Cb alloy increases the as -quenched hardness of the hexagonal martensitic a' phase, produced by water-quenching bccß-Zr phase, by about 35 pct. This strengthening has been attributed to the solid -solution hardening of the matrix. On aging ternary martensite, a' phase reverts to equilibrium a and Zr2Cu and ß-Cb precipitate out, mainly at the twin and grain boundaries, causing a secondary hardening of the matrix. COLD-worked Zircaloy-2 pressure tubes have been in use in power reactors for a considerable period of time. The search for a better material led to the development of Zr-2.5 wt pct Cb alloy which in the quench-aged condition develops 50 pct more strength than that of cold-worked Zircaloy-2, however, its corrosion resistance in water and steam in the temperature range of 316" to 400°C, in absence of neutron flux, is inferior to that of zircaloy-2.' Work carried out by Ells et al.1 and Dalgaard2 has shown that the corrosion properties of Zr-2.5 wt pct Cb alloy can be considerably improved by the ternary addition of 0.5 wt pct Cu. This paper is concerned with the effect of 0.5 wt pct Cu on the formation of martensitic a and its aging characteristics in a Zr-2.5 wt pct Cb alloy. MATERIALS AND EXPERIMENTAL TECHNIQUES Zr-2.5 Cb-0.5 Cu (referred to as the ternary alloy) and Zr-2.5 Cb (referred to as the binary alloy) alloys, supplied by the Chalk River Nuclear Laboratories of the AECL were used. The detailed chemical analysis is given in Table I. Cold rolling and swagging with frequent intermediate anneal of 1000°C were used for the initial fabrication of the alloys. All the heat treatments were carried out after the specimens were wrapped in zirconium foils and encapsulated in silica tubes under a vacuum of 5 x 10-6 mm of Hg. For optical metallography and hardness measurements specimens were mechanically and then chemically polished in a 45 pct HNOj, 45 pct HzO, and 10 pct HF solution. Hardness was measured on a Vickers hardness tester using a 10-kg load. For each specimen at least fifteen indentations were made in order to obtain a representative value. The phase identification and structural analysis were carried out using X-rays and electron diffraction techniques. Wires of 1.5 mm diam reduced to 0.12 mm diam by chemical etching were used for making Debye-Scherrer powder patterns using Cu Ka radiation in a 114.6 mm diam camera. Carbon extraction replicas were prepared by etching the specimens, after depositing a layer of carbon on the metallographic specimen, in one part HF and thirty parts ethyl alcohol. Thin films were prepared by electropolishing heat-treated 3/4 by 1/2 by 0.005 in. thick strips using a modified Bollman-Window technique. The 10 pct perchloric acid-90 pct methyl alcohol bath was kept at -50°C and polishing was done at 5 to 10 V. The thinned specimens were washed in ethyl alcohol at -30º to -40°C and dried between filter papers. Replicas and thin films were examined in a Phillips 300 G electron microscope. For resistivity measurements thin strip specimens 0.02 by 0.3 by 10.0 cm long were used. The potential leads were spot welded to the specimens in order to maintain a fixed length for the initial and the final resistivity measurements. The resistivity was measured by a Kelvin bridge in a temperature controlled room. The temperature was maintained at 72º ±1°F and the accuracy of the resistivity measurements was 0.03 µa-cm. RESULTS As-Quenched Structures. In order to produce a homogeneous matrix to study the precipitation reaction the solution-treatments of both the alloys were carried out in the -field region. From the Zr-Cb phase diagram due to Lundin and cox3 ß/a + ß phase boundary for Zr-2.5 wt pct Cb alloy is 820°C. Ells et al.1 have reported this boundary for Zr-2.5 Cb alloy containing 1100 ppm 0 to be at 920°C. Also, the addition of 0.5 wt pct Cu reduces this temperature by 50°C. Therefore, the solution-treatments were carried out at 1000°C to ensure that the alloys were in ß-phase region. The soaking time was 1 hr and the specimens were water-quenched. The as-quenched hardness of the binary alloy was 245 Vpn whereas, that of the ternary alloy was 330 Vpn. The X-ray diffraction studies indicated that the as-quenched structure of both the alloys consists of martensitic hexagonal phase a', with a c/a ratio of 1.591, and some retained ß-Zr. The presence of a' phase was further confirmed by thin film electron microscopy. Electron micrographs of typical ß-quenched structures of the ternary and the binary alloys are shown in Figs. 1 and 2, respectively. Fig. 3 shows the diffraction pattern from an area similar to that shown in Fig. 1. Although, the as-quenched hardness of the ternary alloy is about 35 pct greater than that of the binary alloy, the structure of both the alloys seems to be the same. The matrix of both alloys is heavily twinned and shows very few dislocations. Furthermore, there is no evidence of any precipitation taking place in either of the two specimens during quenching from the solution-treatment temperature. Aging Behavior of Martensitic a'. The aging kinetics of the ternary alloy were followed by resistivity and hardness measurements. The as-quenched values

Jan 1, 1970

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the, information received may be what is desired and not include collateral matter which may, not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 4, 1917

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 12, 1917

By N. F. Schulz, H. A. Lex

Representative samples of typical manganiferous iron ores from the Cuyuna Range, Minn., were reduced to the metallic iron state at temperatures just short of fusion with an excess of coke in the manner prescribed by the R-N Direct Reduction Process. The magnetic separation characteristics of the reduced ores were determined at several grinds by means of the Davis magnetic tube concentrator. The efficiency of metallic iron concentration by magnetic separation was a direct function of the degree of metallization of the ore sample and of the degree of liberation at-tained in grinding. Some improvement of liberation characteristics was observed if a small amount of sodium chloride was present in the ore during reduction. Despite the extremely fine-grained structure of the crude ores, iron concentrates containing more than 90% Fe at iron unit recoveries of 90% or more were obtained from well-metallized samples of three of the four ores tested. The rejection of manganese to the tailings corresponding to such separations varied from 80% to 95%. The manganiferous iron ores of the Cuyuna Range in Minnesota constitute a major potential source of manganese in the United States provided that a technically and economically feasible process can be devised for its recovery. The iron and manganese of these ores occur chiefly as oxides or carbonates in the form of very small, irregular, discrete grains embedded in a matrix of quartz or other siliceous gangue. The present investigation was undertaken as a sequel to an earlier one conducted jointly by the U.S. Bureau of Mines and the R-N Corp. Those results indicated that the R-N Direct Reduction Process might be a means for recovering both a metallic iron concentrate and a marketable manganese by-product from Cuyuna manganiferous iron ores.' The R-N Process is one of many proposed schemes for the treatment of crude iron ores involving the di- rect reduction of the iron content to metallic iron followed by physical extraction of the iron. In general, it consists of the following stepsz2 1) Iron oxide in crushed natural ores or iron concentrates is about 95% reduced to metallic iron at elevated temperatures but without fusion in a rotary kiln in the presence of a solid carbonaceous fuel (usually coke), limestone, and combustible gases. 2) The kiln product, consisting of metallized ore, excess coke, lime, and coke ash is cooled. The excess coke is recovered and recycled to the kiln feed. 3) The metallized ore is ground for liberation and magnetically separated to yield a metallic iron concentrate. 4) The metallic iron concentrate is agglomerated by a briquetting process. The reduction kiln temperatures must be high enough for the desirable chemical reactions to proceed at practical rates without causing fusion of any of the ore constituents. The time of exposure of the ore to the reducing conditions must be ample for 90% to 95% metallization of the iron oxides present. If more than 95% of the iron is metallized, however, difficulties may arise in the briquetting step, presumably because of accompanying higher carbon content of the metallic iron. Although not always necessary, powdered limestone or dolomite may be added at some time during reduction to aid in eliminating sulfur and phosphorus from the final product.3,4 Other additives, notably sodium chloride, when present during reduction, result in improved liberation characteristics of the metallic iron from certain reduced ores.'v6 Under the reducing conditions normally employed, P(co + H2)= 1 atmosphere, and 1830' to 2150°F (1000° to 1170°C), the R-N Process is claimed to be adaptable to a wide variety of low, medium, and high grade iron and manganiferous iron ores. The manganese oxides and carbonates are reduced mostly to nonmagnetic MnO which is rejected to the nonmagnetic tailings. Manganese-bearing pyroxenes of the original ore, however, may be rejected poorly, if at all, apparently because these minerals occur within the iron lattice or are entrapped in the metal particles.7 The investigation was limited to studies of the Cuyuna ores listed in Table I, which were reduced to the metallic iron state under various conditions

Jan 1, 1969

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral. matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 3, 1917

By D. M. Jamieson, M. P. Pearse, E. R. A. Plumstead

In 1948 the shaft sinking record in the Republic of South Africa was held by the Van Dyk Consolidated Mines Ltd. for a ventilation shaft with a footage of 461 ft sunk during the month of August 1941. This record remained for some ten years; but in the ensuing nine years it was broken no less than 13 times. Table I gives shaft sinking records throughout the world for the 21 years, 1940 to 1960. History shows that the wide, deep, timbered rectangular shaft had passed its peak of popularity by 1948, although it still had a great deal to commend it, both from the sinking and operational points of view. In sinking, it is easy to clean manually, and water can be handled by bailing when wet ground has to be negotiated; its shape also lends itself to equipping concurrently with sinking. In operation it provides the most convenient "in line" hoisting arrangement, and if the ventilation requirements so demand, it offers the simplest solution in that it can be divided into upcast and downcast sections. Furthermore, in the case of a multi-level mine, the shaft compartments can be reduced conveniently if the full area of the shaft is not required to serve all levels.

Jan 4, 1963

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 11, 1917

By N. S. Stoloff, R. C. Ku, R. G. Davies

The stress-strain behavior of Fe-Co and Fe- V alloys containing up to 25 pct solute have been studied in the temperature range 25° to - 196°C. The microyield stress is independent of temperature for all alloys studied, while the temperature dependence of the ordinary yield stress is large and comparable to that for unalloyed iron. An alloy-softening phenomenon is observed for many alloys relative to unalloyed iron, and appears to be a consequence of removal of inter-stitials from solution and their subsequent agglomeration. The ductile to brittle transition temperature is increased markedly by both cobalt and vanadium. Transmission electron microscopy observations reveal that cross slip and cell formation are restricted with increasing solute, which can account for many aspects of yielding and fracture behavior. IRON and other metals of bcc structure slip on many planes of the (111) zone at moderate and elevated temperatures, giving rise to wavy glide. At low temperatures, however, there is a tendency for slip to be restricted to planes of only one or two crystallographic types; in the case of Fe-Si alloys for example, (110) glide predominates, giving rise to planar slip bands."' Restriction of cross slip at low temperatures in iron has been linked by Brown and Ekvall3 to increased strain hardening in the preyield microstrain region, leading to an apparently large temperature dependence of the yield stress. Support for this view has been provided by Lawley and Gaigher4 from a transmission electron microscope study of molybdenum. They concluded that dislocations at lower temperatures, by virtue of their inability to change planes readily, are unable to interact and annihilate, leading to an increase in internal stress and work-hardening capacity. Restriction of cross slip at low temperatures has also been suggested to be an important factor in determining the ductile to brittle transition of single-phase solids, including metals of bcc structure.5 It is pertinent to note that most solute elements tend to raise the ductile to brittle transition temperature of poly crystalline ferrite,6,7 although in some cases, e.g., Fe-Cr7 and Fe-Al,8 the dilute alloys may actually yield at lower stresses than unalloyed iron. It appears, therefore, that solute elements may have an effect analogous to lowering the test temperature with regard to restricting cross glide. Such an effect has indeed been observed in the ionic alloy system KCl-KBr,9 in which bromine atoms, although causing little misfit and consequently little effect on the yield stress of KC1, have a pronounced effect in restricting wavy glide and inducing brittleness. The purpose of the present investigation was to determine the effects of selected solute atoms on the yield stress and fracture behavior of iron, and to elucidate in turn how the slip character was related to these properties. Since it is known that interstitial atoms exert a strong influence on the mechanical behavior of iron, the solute elements chosen for study were vanadium, which reacts strong with interstitials,10 and cobalt, which does not form highly stable interstitial compounds." EXPERIMENTAL PROCEDURE Four-pound ingots of each of the following alloys were vacuum-melted in zirconia crucibles: Fe-1, 5, 10, 25 at. pct Co, and Fe-1, 4, 10, 20 at. pct V. An ingot of unalloyed iron from the same original stock as that used for the alloy was remelted under similar conditions to eliminate variations in interstitial content arising from differing thermal histories. Chemical analyses of the iron, cobalt, and vanadium melt stock are listed in Table I. All ingots were rolled and swaged, commencing at 850°C, to 1/4-in.-diameter bar. The bars were then annealed at 850°C for 1 hr (except that the 10 and 20 pct V alloys were heated for 2 hr) to give a uniform equiaxed grain size of about 0.05 mm. Tensile samples of 0.125 in. diameter by 0.8 in. gage length were utilized for studies of the ductile to brittle transition. A second set of tensile samples were utilized for microstrain experiments in which strain sensitivity of 1 x 10"6 was achieved by a capacitance method.3 Cylindrical compression samples 0.250 in. diameter by 0.4 in. long also were prepared to study the influence of composition on the macroscopic yield stress, and for metallographic analyses of defor-

Jan 1, 1965

By James R. Stuart

AS the available remaining properties of iron ore reserves on the Mesabi Range are opened up for mining, the various properties located under lake beds are brought nearer an active status. The actual physical problems involved in stripping these properties do not act as a deterrent so much as the legal and political problems that are encountered. When it is proposed to destroy a natural lake that has been used by the public for many years, much local as well as state opposition may be encountered regarding its destruction. Public hearings must be held and some adverse publicity is likely to result. The ownership of the ore under the lake and the rights of the abutting property owners must be settled, and protection from damage caused by a disturbance in surface and subsurface drainage is likely to be demanded by property owners some distance from the proposed mine area. The Embarrass Mine, located near Biwabik, Minn., falls into this classification. A portion of the orebody lies under what was formerly Syracuse Lake, this body of water having been removed in the process of stripping the mine. An additional problem in the case of a meandered body of water is the establishment of a meander line that can be projected downward as mining progresses to form the basis for a satisfactory division between lake bed and upland ore shipments for royalty purposes. Fig. 1 illustrates the complications encountered in maintaining these divisions. A balance point was agreed upon in the center of the lake to make an equable division of lake bed ore to the abutting properties. The entire lake bed has since been adjudged the property of Minnesota. Lake Characteristics Lake bed stripping problems with which this paper is concerned necessarily are limited to a specific type of lake, namely the glacial lakes of the Lake Superior region. One characteristic common to these bodies of water is a deposit of fine black mud or silt on the bottom, frequently underlain by a layer of impervious blue clay. This is also true of the muskeg areas of the region, which present almost identical problems as lakes in stripping. The actual removal of the water and the lake bed material is a routine matter more or less standardized as to equipment, and the period of time required can be estimated easily on the basis of volume and capacity. More important than the foregoing is the execution of preliminary work, and above all, the timing involved. An account could be prepared based entirely on statistical and cost data which would give a very fair picture of the time required and cash outlay needed to effect the removal of a body of water preliminary to stripping the orebody. However, the real interest from the standpoint of the operator and the engineer who carry responsibility for completion of the job lies in the unexpected emergencies and the action of various materials involved in the stripping when the balance has been upset through diversion of water courses and the reduction of the lake level. Runoff and Drainage Lakes are located in natural basins that catch all the rain water and runoff water for a considerable area. Where a lake is involved having an inlet and outlet or a sizeable water course running through it, the drainage area may include a watershed covering many square miles. All available data then must be collected to supply a history extending over as many years for which information can be gathered on the flow of streams, annual rain and snowfall, and most important, the peak flows to be expected. Where the diversion of a stream around the stripping area is a part of the problem, this last factor is of great importance since it controls the cross-section to be selected for the diversion channel and the volume to be removed in its excavation, as well as affecting the hydraulic considerations to be met in the design of the completed channel. Characteristic material in the overburden found at the Embarrass Mine is illustrated in Fig. 2. Well Pumping Pumping from the well holes was started well in advance of the draining of the lake. Fig. 3 shows a gradual lowering of the water table with no noticeable fluctuations during the period in which the lake was being dewatered. Unfortunately, because of tight ground, a maximum flow to the wells was not maintained. This retarded the rate at which the water table was reduced so that in the course of stripping the excavation soon extended below the water table, and the great bulk of the pumping was handled from a system of sumps in the pit itself. Any dewatering program projected by prepumping from wells, a glorified well point system, would have to be started well in advance of the stripping to be of any great advantage. Preliminary drainage of the surface over the mine area is entirely apart from the actual elimination of the lake bed itself. Since the lake is what is called a perched water table because of the impervious character of the lake bottom, the adjoining surface may be dewatered below the surface of the existing lake and the flow will not be affected by the proximity of that body of water. This condition actually has been demonstrated through the establishment of a number of observation holes where a small churn drill was used to put down the holes and a 3-in. pipe was installed for taking water level

Jan 1, 1952

By J. L. Foster, G. R. Gray, T. S. Chapman

The wall-building properties of salt-water drilling muds can be improved markedly by the addition of: (I) natural gums, such as traga-canth, karaya, and ghatti; (2) seaweeds, such as Irish moss; or (3) gelatinized starch. Results of laboratory tests have been confirmed by field trials. For drilling operations in which the mud becomes contaminated by salt, either through penetrating salt-bearing rocks or by addition of sea water to the mud, the added cost resulting from the use of one of the substances listed above is more than offset by freedom from stuck drill pipe and ease in running casing. Introduction It has been recognized for many years that oil production might be seriously hampered by infiltration of water from the drilling mud.l-4 As knowledge of the mechanism of the wall-building process advanced, methods were developed for evaluating the filtration characteristics of muds.5-ll The wall-building properties of freshwater muds are commonly regulated by the addition of bentonitic clays, or of agents to promote the dispersion of the natural mud solids. When strata bearing soluble salts are encountered in the course of drilling, the salts are incorporated in the mud; the clay solids are flocculated and water loss is increased tremendously. Methods gen-crally used in controlling filtration of freshwater muds are no longer applicable. The problem of reducing water loss from salt-water muds is not confined to any particular area, but is acute in parts of West Texas. Salt beds several hundred feet thick must be penetrated before the oil-bearing formation is reached. Since the formation drilled does not provide mud-making material, it is necessary to use large quantities of commercial clays, and even the best commercial clay does not afford relief from the problem of high filtration. A laboratory study has been made of methods of improving the filtration characteristics of salt-water muds, and some of the methods have been used in field practice. Laboratory Investigations Procedure Inasmuch as the immediate object of the investigation was the development of means of improving the wall-building properties of muds used in West Texas, an attempt was made to employ muds in the laboratory study comparable to those in field use. Samples of muds used in drilling the producing formations in six wells were secured. The properties of these samples are summarized in Table I, which lists the densities, viscosities, filtrations, and analyses of the filtrates for calcium, chloride, and sulphate. Viscosity was measured in the Stormer viscosimeter at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester8 at a pressure of 100 lb. per sq. in. Filtration rates are considerably higher than those of usual fresh-water muds, which amount to about 20 C.C. in 30 min. Water loss was so rapid in samples 4, 5 and 6 that filtration was complete in less than 10 min. and the values for 30 min. were extrapolated from the rates at shorter

Jan 1, 1942

By G. R. Gray, T. S. Chapman, J. L. Foster

The wall-building properties of salt-water drilling muds can be improved markedly by the addition of: (I) natural gums, such as traga-canth, karaya, and ghatti; (2) seaweeds, such as Irish moss; or (3) gelatinized starch. Results of laboratory tests have been confirmed by field trials. For drilling operations in which the mud becomes contaminated by salt, either through penetrating salt-bearing rocks or by addition of sea water to the mud, the added cost resulting from the use of one of the substances listed above is more than offset by freedom from stuck drill pipe and ease in running casing. Introduction It has been recognized for many years that oil production might be seriously hampered by infiltration of water from the drilling mud.l-4 As knowledge of the mechanism of the wall-building process advanced, methods were developed for evaluating the filtration characteristics of muds.5-ll The wall-building properties of freshwater muds are commonly regulated by the addition of bentonitic clays, or of agents to promote the dispersion of the natural mud solids. When strata bearing soluble salts are encountered in the course of drilling, the salts are incorporated in the mud; the clay solids are flocculated and water loss is increased tremendously. Methods gen-crally used in controlling filtration of freshwater muds are no longer applicable. The problem of reducing water loss from salt-water muds is not confined to any particular area, but is acute in parts of West Texas. Salt beds several hundred feet thick must be penetrated before the oil-bearing formation is reached. Since the formation drilled does not provide mud-making material, it is necessary to use large quantities of commercial clays, and even the best commercial clay does not afford relief from the problem of high filtration. A laboratory study has been made of methods of improving the filtration characteristics of salt-water muds, and some of the methods have been used in field practice. Laboratory Investigations Procedure Inasmuch as the immediate object of the investigation was the development of means of improving the wall-building properties of muds used in West Texas, an attempt was made to employ muds in the laboratory study comparable to those in field use. Samples of muds used in drilling the producing formations in six wells were secured. The properties of these samples are summarized in Table I, which lists the densities, viscosities, filtrations, and analyses of the filtrates for calcium, chloride, and sulphate. Viscosity was measured in the Stormer viscosimeter at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester8 at a pressure of 100 lb. per sq. in. Filtration rates are considerably higher than those of usual fresh-water muds, which amount to about 20 C.C. in 30 min. Water loss was so rapid in samples 4, 5 and 6 that filtration was complete in less than 10 min. and the values for 30 min. were extrapolated from the rates at shorter

Jan 1, 1942

By Frank Foote, E. R. Jette

Precision lattice-constant measurements have been widely used in the study of cubic solid solutions but as yet have been rarely applied to noncubic solid solutions. (See, however, references I and 2.) With the high precision at present attainable in the measurement of lattice constants, the X-ray method should be readily applicable to noncubic solid solutions. In the work reported here, hexagonal close-packed magnesium was used as the solvent and either lead, bismuth or gold as the solute. In the magnesium-lead and magnesium-bismuth systems the a and c lattice constants were determined as a function of composition, densities were calculated from these lattice-constant data, these theoretical densities were compared with those directly measured and the solid solubility limit was determined on quenched specimens over a considerable range of temperature. In the magnesium-gold system, the solid solubility is very small but we have obtained an indirect check on the solubility limit previously reported. Materials and Preparation oF the Alloys The magnesium used was obtained from the Aluminum Company of America and was 99.987 per cent pure. Impurities as reported On the label were: Fe, Al, 0'004 per cent; Si, 0.009 per cent; Zn, trace; Cu, Pb, nil. The bismuth was Merck's analytical grade, minimum purity 99.95 per cent. Maximum impurities as listed on the label were: Fe, 0.008 per cent; Pb, 0.010 per cent; Ag, 0.010 per cent; Cu, 0.005 per cent; Sn, 0.003 per cent; Sb, 0.00; As, 0.000; S, 0.01 per cent. The gold was purified by double precipitation with sulphur dioxide. The lattice constants of these three metals have been previously reported.3 The lead used was test lead, silver free and with a maximum of 0.10 per cent heavy metal impurities. The lattice constant 01 this lead has been measured and found to be 4.94057 ± 0.00016 at 25°C. The alloys were prepared by melting together weighed amounts of the constituent metals in magnesia-lined alundum crucibles under an atmosphere of hydrogen purified by passing over magnesium heated to 500°C. The magnesia lining prevented contamination 01 the alloys with aluminum. Vacuum melting could not be used because of the volatility of magnesium. A high-frequency induction furnace was used for the melting operation and the stirring action of the current resulted in thorough mixing of the constituents. The melts were allowed to freeze in the crucible, the ingots obtained weighed about 10 grams. An extremely thin white film formed on the surface of the melts, sometimes covering only a part of the exposed surface. The ingots were filed clean, placed in small iror crucibles with close-fitting lids and indi. vidually sealed into Pyrex glass tubes Before sealing off, the tubes were alter

Jan 1, 1941

By Frank Foote, E. R. Jette

Precision lattice-constant measurements have been widely used in the study of cubic solid solutions but as yet have been rarely applied to noncubic solid solutions. (See, however, references I and 2.) With the high precision at present attainable in the measurement of lattice constants, the X-ray method should be readily applicable to noncubic solid solutions. In the work reported here, hexagonal close-packed magnesium was used as the solvent and either lead, bismuth or gold as the solute. In the magnesium-lead and magnesium-bismuth systems the a and c lattice constants were determined as a function of composition, densities were calculated from these lattice-constant data, these theoretical densities were compared with those directly measured and the solid solubility limit was determined on quenched specimens over a considerable range of temperature. In the magnesium-gold system, the solid solubility is very small but we have obtained an indirect check on the solubility limit previously reported. Materials and Preparation oF the Alloys The magnesium used was obtained from the Aluminum Company of America and was 99.987 per cent pure. Impurities as reported On the label were: Fe, Al, 0'004 per cent; Si, 0.009 per cent; Zn, trace; Cu, Pb, nil. The bismuth was Merck's analytical grade, minimum purity 99.95 per cent. Maximum impurities as listed on the label were: Fe, 0.008 per cent; Pb, 0.010 per cent; Ag, 0.010 per cent; Cu, 0.005 per cent; Sn, 0.003 per cent; Sb, 0.00; As, 0.000; S, 0.01 per cent. The gold was purified by double precipitation with sulphur dioxide. The lattice constants of these three metals have been previously reported.3 The lead used was test lead, silver free and with a maximum of 0.10 per cent heavy metal impurities. The lattice constant 01 this lead has been measured and found to be 4.94057 ± 0.00016 at 25°C. The alloys were prepared by melting together weighed amounts of the constituent metals in magnesia-lined alundum crucibles under an atmosphere of hydrogen purified by passing over magnesium heated to 500°C. The magnesia lining prevented contamination 01 the alloys with aluminum. Vacuum melting could not be used because of the volatility of magnesium. A high-frequency induction furnace was used for the melting operation and the stirring action of the current resulted in thorough mixing of the constituents. The melts were allowed to freeze in the crucible, the ingots obtained weighed about 10 grams. An extremely thin white film formed on the surface of the melts, sometimes covering only a part of the exposed surface. The ingots were filed clean, placed in small iror crucibles with close-fitting lids and indi. vidually sealed into Pyrex glass tubes Before sealing off, the tubes were alter

Jan 1, 1941

By L. Adler

A relatively simple and effective technique is proposed to deal with the failure of geologic masses containing weakness planes. This technique, termed irextended" rupture envelope, provides a means to clearly distinguish rock and soil from fractured rock and, on a theoretical level, considers a matrix-inclusion system. It may also constitute the link between Mohr's and Griffith's failure theories. Included in the article are five sample problems concerning site location, structural design, strengthening the plane of weakness, changing the magnitudes of major and minor principal stresses and changing the orientations of major and minor principal stresses. Engineers trying to solve design problems in rock and soil mechanics have often assumed an iso-tropic and homogeneous medium. For naturally occurring geologic masses this assumption has always been viewed with regret. The following analysis which deals with the effects of plane anisotropy on failure presents a solution to this. The planes of weakness are joints, faults, bedding planes, fracture and cleavage (natural and induced), foliation and schistosity. The physical properties of these weakness planes include an undulating surface, frictional resistance, discontinuous extent, filling material, tightness and presence of water to cause a hydrostatic pore pressure. All of these properties relating to failure can be summarized in Mohr's rupture envelope for the plane of weakness. This, along with the geometrical orientation, strike and dip, of the plane of weakness produces what is termed an irextended" rupture envelope. MOHR'S STRESS CIRCLE AND RUPTURE ENVELOPE The significant features of these concepts are listed below.' 1) A point on the u - r coordinate plane represents the normal and tangential stress components on a reference area in the material. This area can have any orientation. (Fig. la)

Jan 1, 1963

NAME AND OBJECT. SEC. 1. This Institute is incorporated under the Membership Corporation Law of the State of New York ; its corporate name is AMERICAN INSTITUTE OF MINING ENGINEERS; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely (1) Members ; (2) Honorary Members , (3) Associates , and (4) Honorary Associates Only Members and Associates residing within the United States of America, Republic of Mexico and Dominion of Canada shall be entitled to vote at the meetings of the Institute. SEC. 2 All Members, Honorary Members, Associates and Honorary Associates of the American Institute of Mining Engineers as the same existed on the day of the incorporation of this Institute, are Members, Honorary Members, Associates and Honorary Associates, respectively, of this Corporation SEC. 3. The following classes of persons shall be eligible for membership in the Institute, namely, as Members and Honorary Members, all professional mining engineers, geologists, metallurgists or chemists, and all persons practically engaged in mining, metallurgy or metallurgical engineering ; as Associates and Honorary Associates, all persons desirous of being connected with the Institute who, in the opinion of the Council, are suitable. SEC 4. Every candidate for election as a Member or Associate of the Institute must be proposed for election by at least three Members or Associates; must be approved by the Committee on Membership, as prescribed in the By-Laws ; and .must be elected by the Council. Not less than three-fourths of the votes cast shall be necessary to an election Every person so elected shall become a Member or Associate, as the case may be, upon payment of his first dues as herein-after prescribed Each candidate for Honorary Member or Honorary Associate, must be recommended by at least ten Members or Associates ; must be approved by the Council ; and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of all the Directors present ; provided, however, that the number of Honorary Members and Honorary Associates shall not at any time exceed twenty SEC. 5. If any person elected a Member or Associate does not, within sixty days after notice of his election, accept the same and pay his initiation fee and dues for the current year, his election may be cancelled at the discretion of the Council.

Jan 1, 1910

By C. E. Mendenhall

THE word temperature has both a colloquial and a technical use. For everyday purposes of abusing the weather man, no very exact definition is necessary, but for the purpose of giving a simple summary of the physical laws that form the basis of practical pyrometry, something more precise is required. Beginning, therefore, with the common concept of "hotness" and "coldness," we must agree on a method of measuring differences in "hotness," on the unit to be used, and on the point from which measurements are to be taken. We shall then have a definite "scale of temperature," which can be used in all methods of pyrometry. But, as in many similar cases, it is much easier to define or describe something than it is to make practical application and use of the definition; so that much of our attention will be taken up with practical methods of realizing or applying the scale agreed upon. It was early observed that changes in temperature produced large and easily measurable changes in gases, which may be most simply separated into changes in volume (expansion and contraction) under conditions of constant pressure, and changes in pressure under conditions of constant volume. These changes are much the same in magnitude for the common gases oxygen, nitrogen, and hydrogen and also for the rarer helium and argon. This relative uniformity in behavior led to the suggestion of "the gas thermometer" and "the gas scale" as the basis for all temperature measurements. However, as methods were refined, differences appeared between different gases and different ways of using gases, so that Lord Kelvin introduced his more fundamental notion of the "absolute thermodynamic scale" of temperature, which he defined as follows: Given two bodies, say two tanks of water, at different temperatures to determine these temperatures on the "absolute thermodynamic," or Kelvin, scale, operate a thermal engine between these two temperatures, letting it take in heat from the hot body and give out heat to the cold, which therefore corresponds to the boiler and the condenser of a steam engine. The engine we may imagine as a cylinder and piston inclosing a gas and operating with the well-known Carnot or isothermal-

Jan 9, 1919

By Samuel D. Warriner

The dealings between concentrated capital invested in the conduct of our various industries and the combinations of labor known as "trade union organizations," have produced not only in the United States, but abroad, many novel methods of negotiation between employers and wage-workers. The size and strength of these organizations have destroyed the personal elements formerly governing the dealings between employer and employee, and have produced various forms of trade-agreements now in more or less successful operation. The difficulty, however, has been to secure consent of both parties to an equitable agreement. For this purpose there have been devised various forms of arbitration, either compulsory under the shadow of governmental legislation, or voluntary by mutual agreement. But these have not been altogether successful from a technical stand-point, for the reason that a compromise has generally been necessary, and in an effort to reach an agreement, terms have been made which have been neither fair nor satisfactory to either of the contending parties. The Anthracite Board of Conciliation represents one of the few thoroughly successful courts for the settlement of trade-disputes, if not the only one which has yet been evolved. The prestige of this board rests upon its successful treatment of the labor-troubles of the anthracite region for a period of more than eight years, and upon the fact that it has been able

Jan 1, 1912

By G. D. Cremer, J. J. Cordiano

ALUMINUM powder is a well-known article of commerce and in various forms has been marketed widely for use in paint, for pyrotechnic purposes and for exothermic mixtures. For a number of reasons, how- ever, aluminum powder has not been employed extensively in powder metallurgy, although a great many proposals along this line have been offered. Aluminum and aluminum-alloy powders oxidize readily upon exposure to air and the thin film of oxide (or hydroxide) thus formed is highly refractory, in that ordinary gaseous reducing agents such as hydrogen or carbon monoxide do not reduce the oxide to metal at temperatures below the melting point of aluminum. It has been thought that the presence of these films of oxide on aluminum particles would interfere markedly in powder metallurgical work and a number of suggestions have been made, either for preventing the formation of the film through the production of the powders in inert or reducing atmospheres, or for the removal of the oxide by means of powerful reducing agents, including "nascent" or atomic hydrogen released from metal hydrides. 4 second and more serious difficulty in the use of aluminum and aluminum-alloy powders in powder metallurgy resides in the fact that during compression such powders tend to adhere or cold-weld to the die walls, thus interfering with the formation and ejection of a compact. A third difficulty, which has been encountered only with aluminum-alloy powders, is their hardness when compared with elemental aluminum. Certain of these powders are susceptible to age- hardening, which further hinders the formation of strong green compacts. These conditions are particularly true of atomized aluminum-alloy powders. Even in the annealed condition, plastic deformation of alloy powders under pressure is low when compared with unalloyed powders. This fact, coupled with the lower corrosion resistance of the alloy powders, is probably the significant factor in our failure to obtain strong sintered pieces. METHODS OF PRODUCING THE POWER Many methods have been proposed for manufacture of aluminum powder, only a few of which are used commercially. Several of the more important processes include: (I) atomization of the molten metal; (2) mechanical pulverization and other types of comminution; and (3) graining, in which molten aluminum is stirred during freezing. For pigment and certain pyrotechnic uses aluminum flake powder is desirable, because of its greater proportion of surface to volume; and large quantities of such material are made by a procedure that involves stamping or ball milling. In making flake intended for use as pigment,

Jan 1, 1943

By E. E. Thurlow

The Geology Div. of Northern Pacific Railway Co. has adapted to its exploration efforts field procedures for geochemical sampling and semi-quantitative analysis which have been developed through research by the U. S. Geological Survey. The sampling is done in conjunction with reconnaissance geologic mapping on aerial photographs or during field checking of maps which have been prepared largely by photo-geologic interpretation. Stream sediment or soil samples are taken and readily soluble combined heavy metals are extracted with ammonium citrate followed by colorimetric titration with dithizone at the sample site. The effectiveness of this approach has been demonstrated both in positive and negative results, thereby assisting in the elimination of large areas of land from further immediate attention and in providing targets for followup exploration. An occa sional sample is submitted for spectrographic analysis as a check on the possible presence of other elements of economic significance. Field laboratory procedures are also being implemented for determining molybdenum, mercury, and other metals which may be valuable in themselves or useful as pathfinder elements in outlining mineralized areas. A lead-zinc occurrence in Oregon and a copper deposit in Montana were readily detected and outlined by stream sediment and soil sampling and a heavy metal anomaly that lacks obvious interpretation has been found in northwestern Montana. Detailed mapping and additional sampling are followed by other exploration techniques if warranted. Northern Pacific's program of reconnaissance mineral evaluation of company-owned lands and adjoining areas was outlined in a paper presented at the American Mining Congress meeting in Las Vegas four years ago. That report included policies and procedures with respect to mineral development on Railway Co. lands and may be referred to for information on these matters.1 In a sense this paper is a progress report on the use of geochemical prospecting in Northern Pacific's continuing mineral evaluation program. At this time there are positive results but as yet there is no real success story in the form of a minable ore body. GEOCHEMICAL PROSPECTING PROCEDURES The decision to use geochemistry as a reconnaissance exploration tool must be followed by research into sampling and analytical methods and into the interpretation of results. Various analytical methods were tried and evaluated by the Geology Div., including hot and cold acid extraction with and without fusion of the sample, panning and magnetic separation followed by dithizone testing of the magnetite, and cold aqueous extraction of metallic ions followed by indicator tests. Samples were first sent to the laboratory for analysis; later field laboratories were established and now virtually all testing is done at the sample site. It was concluded that, where applicable, the quickest dependable methods for reconnaissance use are the dithizone field tests for readily extractable heavy metals. This involves the simultaneous treatment of a sample, usually of soil or stream sediment, with two immiscible liquids; one a cold aqueous extractant (ammonium citrate) and the other a solution of dithizone in toluene or xylene.2 Dithizone is a colorimetric indicator that reacts quantitatively with copper, lead, zinc, and several other metals to form colored complexes in organic solvents. Results may be expressed in ml of 0.001 pct dithizone that are required to reach the blue end point, or calibration of the test results can be carried out with standard solutions of zinc; conversion factors would then be expressed in ppm, zinc equivalent. Calibration of dithizone solution with zinc standards indicates that 1 ml of 0.001 pct dithizone is equivalent to approximately 0.25 ppm of zinc. An authoritative report on dithizone field tests authored by H. E. Hawkes in the June-July 1963 issue of Economic Geology* states "The appeal of these techniques has been the simplicity and speed of the determinations as compared with more tedious laboratory determinations of trace metals in weathered rocks, soils, or plant materials. This obvious appeal, however, has often been more than matched by misuse of the method in such a manner that the results are

Jan 1, 1964

NAME AND OBJECT. SEC. 1. This Institute is incorporated under the Membership Corporation Law of the State of New York ; its corporate name is AMERICAN INSTITUTE OF MINING ENGINEERS; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely (1) Members ; (2) Honorary Members , (3) Associates , and (4) Honorary Associates Only Members and Associates residing within the United States of America, Republic of Mexico and Dominion of Canada shall be entitled to vote at the meetings of the Institute. SEC. 2 All Members, Honorary Members, Associates and Honorary Associates of the American Institute of Mining Engineers as the same existed on the day of the incorporation of this Institute, are Members, Honorary Members, Associates and Honorary Associates, respectively, of this Corporation SEC. 3. The following classes of persons shall be eligible for membership in the Institute, namely, as Members and Honorary Members, all professional mining engineers, geologists, metallurgists or chemists, and all persons practically engaged in mining, metallurgy or metallurgical engineering ; as Associates and Honorary Associates, all persons desirous of being connected with the Institute who, in the opinion of the Council, are suitable. SEC 4. Every candidate for election as a Member or Associate of the Institute must be proposed for election by at least three Members or Associates; must be approved by the Committee on Membership, as prescribed in the By-Laws ; and .must be elected by the Council. Not less than three-fourths of the votes cast shall be necessary to an election Every person so elected shall become a Member or Associate, as the case may be, upon payment of his first dues as herein-after prescribed Each candidate for Honorary Member or Honorary Associate, must be recommended by at least ten Members or Associates ; must be approved by the Council ; and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of all the Directors present ; provided, however, that the number of Honorary Members and Honorary Associates shall not at any time exceed twenty SEC. 5. If any person elected a Member or Associate does not, within sixty days after notice of his election, accept the same and pay his initiation fee and dues for the current year, his election may be cancelled at the discretion of the Council.

Jan 1, 1910