Search Documents

In a previous paper of this series (1) ,t it was shown that during the creep of single crystals of lead, deformation proceeded to some extent by means of slip on the octahedral plane. This was demonstrated by the formation of slip lines on the surface of the specimens. At first, a few broad bands appeared after a small amount of extension had taken place; then, as extension proceeded, more and finer lines made their appearance until the whole of the specimen surface was covered.The present paper deals with the process of deformation of the creep specimens as revealed by X-ray examination..By the use of this method, the changes taking place in the crystal structure can be observed.EXPERIMENTAL METHODThe method of preparation of the specimens, their size and the purity of the lead employed have been reported elsewhere (1). At frequent intervals, the specimens were dismantled from the test rack and X-ray back reflection photographs were taken. The specimens were so marked and set up on the X-ray machine that the same spot on the specimen surface was always examined.Copper radiation was employed, the tube voltage and current being 45 kV. and 25 m.a. respectively and the exposure time 2 hrs. The slit diameter was 1 mm.

Jan 1, 1941

By Jones S. C

The problem of sealing a fluid serieite zone at a hole depth of 4000 ft was overcome by using a composite non-return valve plug and rod assembly which enabled cement to be forced under pressure into the zoneà

Jan 1, 1966

Vitrinite reflectance forms the basis of a study of coal rank variation in two areas of the Upper Hunter Valley, New South Wales, on the northern margin of the Sydney Basin. A selective analysis procedure, based on samples rom twenty-two boreholes, has resulted in a small range of reflectance values for each sample and consequently a high degree of significance for calculated mean values. The patterns of rank distribution derived from these data have facilitated an interpretation of the rclative timing of coalilication and deformation in each area.This study provides support for the suggestion by several authors that there were at least two periods of folding in the tJpper Hunter Valley. In the Hebden-Ravensworth area, minor folding took place after most of the coalilication was completed.To the west, in the region of the Muswellbrook Anticline, coalification occurred during or after the formation of this major structure. Tectonic instability during deposition of the Singleton Super-Group, in the region of the Hunter-Thrust on the basin margin, is evidenced by rank variation suggesting differential subsidence across this zone.

Jan 1, 1980

Generating short- and long-term mine production schedules in isolation and independently from each other means that only a local optimum can be achieved when each scheduling phase is carried out. The globally optimal solution however, can be achieved when integrating scheduling phases and accounting for the interaction between short-term and long-term activities simultaneously. This paper addresses the task of integrating short- and long-term production plans by combining the short-term objective of minimising deviation to targeted mill feed grade with the long-term objective of maximising net present value (NPV) into a single mathematical model. A case study is presented which compares the present values of the same stope data set scheduled via separate long and short-term models and than by the proposed integrated model which applies a predetermined penalty for each tonne of metal deviation to target for the respective ore tonnage being processed. This allows an operation to obtain a globally optimal scheduling regime when taking into consideration the cost and loss of value resulting from fluctuations in grade to the mill over the short-term.

Dec 6, 2010

By Met B. E

The increasing pace of modern mining makes constantly greater demands upon the several contributing departments of rock breaking and transport, and rock-drilling, as the spearhead of attack, has received a great deal of attention with respect to both machines and steels. By a series of mechanical improvements, combined with the application of selected heat-treated alloy steels, the rock-drill has now been developed into a machine capable of rapid drilling and long service under severe working conditions. As a factoryproduct made under strict metallurgical control it is as foolproof as, say, the modern automobile, and, like its prototype, it can be kept in efficient operation by a minor amount of attention during use and by periodical adjustments and replacements.The same cannot be said, unfortunately, of the drills with which the machine is supplied; in conventional mine-shop practice these are made of the best tool steel shaped and heat-treated under the poorest of metallurgical conditions.The crudities of steel-shop practice have, in fact, always prevented the full exploitation of the steels available at any time, and even at the present day the general standard of treatment offers a contrast with the quality of the steels which moves the metallurgist to amusement, despondency or outrage, according to his temperament. Nevertheless, the tendency persists to meet the increasing demands of the rock-drill primarily by the use of still better steels, and secondarily by improvement, of the steel-shop practice. Athird type of development is the introduction of factorymade tools in the form of detachable bits and rods. It is proposed in this paper to deal with these three aspects of the recent developments in rock-drilling.*Re-written from a lecturette given during the First Ordinary Meeting, 1936.

Jan 1, 1936

The development of Western Mining Corporation's first commercial gold heap leaching operation is described. The laboratory testwork requirements for determining the amenability of ore to heap leaching techniques is discussed. Heap construction and operating practices are described; and production statistics and operating parameters are presented. It is shown that for a specific low grade gold ore a treatment cost optimization can be performed. Taking cognizance of the ore grade, percentage gold recovery, operating costs, and the gold sale price, it can be determined whether Carbon-In-Pulp (C-I-P) or Heap Leaching should be employed as the extraction process. The examples presented in this paper refer specifically to Kambalda and should not be used in themselves as generalities.

Jan 1, 1987

Thermodynamic properties of the solutions of hydrogen in metals and carbon in austenite were investigated and it is possible to predict the interstitial solubility in these systems over relatively wide ranges of temperature and solute activity. Monte Carlo methods were used to compute the arrangements of interstitial atoms on the tetrahedral sites in body centred cubic metals and the octahedral sites in face centred cubic metals. It was shown that the non-configurational entropies of solution of hydrogen in metals can be interpreted as being principally vibrational and on this basis the potential value of the isotopic solubility ratio theory in indicating the compositional variation of these non-configurational entropies was discussed. The need for future work along these lines is pointed out.

Jan 1, 1970

Sulphuric acid leaching at atmospheric pressure of a number of Australian nickeliferous laterites was examined in detail. The results obtained indicate that nickel can be extracted from these ores, although the conditions required to achieve about 90 per cent extraction vary widely. These differences in reactivity can be related to the types of nickel-bearing minerals present.Nickel is more readily extracted from nickel-bearing clays such as chlorite, than it is from nickel-containing goethite.The results clearly show the problems associated with the processing of complex ores such as the nickeliferous laterites, and they indicate the need for complete characterization of each deposit.

Jan 1, 1978

By M Kozikowski

The primary purpose of these investigations is to determine dewatering requirements and likely impacts associated with mining operations. Standard aquifer testing techniques were carried out at multiple locations within the Ord Range near Pardoo, Western Australia. Aquifer properties of an oxidised haematite orebody were calculated from test pumping data conducted in five fully penetrating test bores. Hydraulic properties of the Ridley magnetite orebody were calculated based on short term constant rate pumping tests, and packer tests. Packer tests were conducted in undeveloped and uncased exploration holes and diamond core holes. The new data sheds light on the hydrogeological properties of this previously unexplored region of Western Australia.Aquifer testing procedures for each bore included a preliminary step test followed by a constant rate test. Recovery data were collected in each bore over a period of four to six hours. Prior to testing, background water levels and water samples were collected in a network of monitoring and exploration bores to establish baseline water levels, gradients and water quality. Water quality within the bedrock of the Ord Range varies from 2000 to 5500 mg/L TDS whereas water quality within the alluvial sequence of the De Grey River is highly variable (400 to 2500 mg/L TDS), but is predominantly brackish with some water of potable quality which is used to supply Port Hedland. Test pumping supports the conceptual hydrogeological model that consists of a pod like orebody (aquifer) surrounded by low permeability waste rock (BIF), with very weak hydraulic connection to the adjacent alluvial systems. Calculated hydraulic conductivity from test pumping data across Pardoo ranged from 0.01 to 59 m/d, depending on deposit tested.A groundwater model was used to simulate dewatering required in proposed pits and to estimate the impact of dewatering on the surrounding shallow alluvial aquifers. Test pumping and numerical groundwater flow modelling indicate the proposed below water table pits can be successfully dewatered utilising in pit dewatering production bores. Yields from individual dewatering bores will reduce with time due to the reduction in saturated aquifer thickness.Based on the numerical groundwater modelling and field investigations the likely impacts to the adjacent De Grey River alluvial aquifer system (within the Priority 1 De Grey River Water Reserve) resulting from mining and dewatering activities is considered minimal. Recalibration of the groundwater model will be undertaken once several months of dewatering data are available.The aim of this paper is to present a range of aquifer parameters derived through standard aquifer testing techniques for an area previously unexplored in terms of hydrogeological characteristics. It is the goal of the authors to provide this comparison data set for future work in similar geologic media.

Jan 1, 2009

Spectrum Resources commenced operations as a public listed mining company in August, 1983, with a variety of precious metal projects in New Zealand. At that time the outlook for most mineral commodities, with the notable exception of precious metals, was decidedly gloomy. Metal prices were depressed and demand forecasts were universally gloomy. Against this background the company reviewed the non-traditional metals sector to try and identify a 'new' metal with an above average demand growth and market value. Lithium, a commodity with exciting new applications in storage batteries and alloys, met both criteria. Annual world consumption of lithium is around 7000 tonnes; current prices are around $NZ40/lb for lithium metal and demand growth is projected at five to seven per cent per annum. Geothermal fluids at Wairakei and elsewhere contain anomalous amounts of lithium and in May, 1984, the Chemistry Division of DSIR was commissioned to carry out a literature survey on the possible recovery of lithium and other minerals from geothermal waters. The survey results were encouraging and the company subsequently negotiated exclusive access rights, for research purposes, to geothermal discharge fluids from the Wairakei and Kawerau geothermal fluids. Most of the subsequent investigations reported here were carried out by Chemistry Division, DSIR, under contract to the company with some assistance from the Industrial Processing Division, DSIR.

Jan 1, 1986

Solid Energy New Zealand Limited owns and operates the Ohai coal field (Wairaki Coal Mining Licence, CML) in western Southland. The Morley Stream passes directly through the middle of the CML and has required diversion in the past to enable open cast mining to proceed. Solid Energy is evaluating two new open cast pits at Ohai. Commissioning these new pits would necessitate further diversion of the Morley Stream. One of these potential new mines is adjacent to an abandoned State Coal Mines (State Coal) pit and there is an opportunity to substantially rehabilitate this old pit as a corollary to the new mine and the stream diversion project.   Past Morley Stream diversions were undertaken by State Coal and so they predated the Resource Management Act 1991 and the degree of community environmental awareness and involvement that has become the norm these days. Not surprisingly the design and construction of the historic stream diversions was based purely upon mining (operational) and engineering considerations. This led to the stream being diverted in a manner that achieved the clinical conveyance of design volumes of water from points A and B.   Solid Energy realised that the proposed new diversions need to adopt more holistic and environmentally sustainable design principles while also including appropriate mining and engineering constraints. This project involved the design of a 1.7 km diversion of the Morley Stream (median flow of about 1000 litres/second) that would enable progressive prestripping and development of the new mines and would also address final rehabilitation (of the stream), geotechnical risks, hydrological and ecological issues. To address all of these factors the project required a multidisciplinary approach. Moreover, it required a clear understanding of how the mining operational constraints could be integrated with the environmental considerations. A significant aspect of the project was how to take account of fishery instream habitat needs, the resource consent requirements and most of all, the involvement of key stakeholders such as the Fish & Game Council, Department of Conservation, the Iwi and local community in the design process. This was achieved through coordinated consultation and stakeholder involvement in a technical design workshop.

Jan 1, 2005

By P Gehrke, S O’Gorman

The precise measurement of NO2 was historically difficult in road tunnels, hence criteria and design analysis was based on converting from NOx concentrations via a set NO2:NOx ratio. The reliable direct measurement of NO2 is now possible, however design analysis is still dominated by emissions tables and formulas specified in terms of NOx. For converting from NOx to NO2 in a road tunnel environment in Australia, the ratio has typically been assumed to be ten?per?cent. This has generally been based on the recommendation in PIARC (2000) and on the ‘average’ value cited in PIARC (1995).Determining this ratio is important as changes in engine technology and in-tunnel pollution criteria along with improvements in CO and particulate emissions control, may mean that NO2 will become the driving factor for future ventilation requirements. Correct selection of this ratio can directly impact the ventilation capacity and system design.Recent research has indicated that choosing a constant ratio of ten?per?cent for all tunnels may not be appropriate. The in-tunnel ratio has been estimated to be as much as 20?per?cent to 30?per?cent and depends on the location in the tunnel, the type of ventilation system and the traffic/fleet characteristics. This paper discusses the effect of some of these parameters on the NO2:NOx ratio in road tunnels.The findings indicate that the ten?per?cent upper limit on the NO2:NOx ratio in PIARC (2000) may be a conservative value for design purposes for longitudinally ventilated road tunnels of typical length in Australia. A value of seven?per?cent to eight?per?cent may be more appropriate in some circumstances. However, the value chosen will depend on the specific tunnel in question and the confidence in traffic conditions expected. Values above ten?per?cent may be encountered for short periods but usually when the NO2 levels are low.CITATION:O’Gorman, S and Gehrke, P, 2014. NO2:NOx ratios in Australian road tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 95–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Techniques Used and Problems Encountered in Normal and Reverse Circulation Drilling at the Mt Roseby Project, Cloncurry, North West Queensland

Sep 13, 2010

By A S. Derrington

High-accuracy, solid-state digital reference barometers have proven to be well suited to conducting underground barometric pressure surveys. The only problem is their expense; at least A$4000 each. For this reason, and because barometric pressure surveys are not a routine undertaking, very few mines have been able to justify the purchase of suitable instruments. The author knows of only three Australian metalliferous mines that own them.However, this may soon change given the recent development of low-cost, mass-produced miniature barometric pressure transducers. These transducers were developed to provide an altimeter function in the latest generation of smartphones. The main purpose of the inbuilt altimeter function is to allow the smartphone to be aware of its altitude when the global positioning system satellite signal is lost.This paper describes a prototype barometer that was constructed using one of the most accurate of the latest generation of piezo-resistive smartphone barometric pressure transducers. The prototype instrument was constructed for less than five per cent of the cost of a commercially available digital reference barometer. The prototype was subsequently tested against a reference barometer at the University of Queensland’s Experimental Mine to verify its accuracy and suitability for measuring pressure differences between underground survey stations.It is expected that the instrument’s low cost will pave the way for barometric pressure surveys to become more commonly used in mines. In turn, the resulting improvement in knowledge of major underground pressure losses should allow mine ventilation officers and engineers to optimise their ventilation systems and potentially reduce overall operating costs.An alternative option would be to use a barometer-equipped smartphone as a survey instrument, provided that its inbuilt barometer module is sufficiently accurate.CITATION:Derrington, A S, 2015. Development of a low-cost instrument for barometric pressure surveys, in Proceedings The Australian Mine Ventilation Conference, pp 331–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By I Zulkarnain, H Permana, R A. Binns

Through an ambitious but relatively low-cost program of marine fieldwork, laboratory investigations and technology-transfer and training activities, three Indonesia-Australia-led marine expeditions were undertaken aboard KR Baruna Jaya VIII between 2001 and 2003. These IASSHA (Indonesia-Australia Survey for Submarine Hydrothermal Activity) cruises have sought to discover and investigate a variety of potential ore forming hydrothermal systems in a range of tectonic settings. All cruises have been successful, both scientifically and from the point of view of training, creation of capabilities and capacity building for such research in Indonesia. Over 60 scientists and technicians from Indonesian and Australian institutions and agencies have been involved. Three new sites and a possible fourth site of hydrothermal activity were discovered in the Sangihe arc in northern Sulawesi. Surveys in the Tomini basin tested a hypothesis based on previous data which suggested this might be an isolated anoxic, brine-filled basin over 2000 m deep where igneous heat sources existed to generate hydrothermal mineralisation. The bay, however, was found to be open to adjacent deep ocean circulation, and there was no evidence of massive base metal sulfides. Subdued evidence of hydrothermal activity was found in the Sunda Strait associated with the famous Krakatau volcano and the extension of the seismically active Semangko Fault. The BANDAMIN program (Indonesia-Germany) covered a portion of the Banda arc in eastern Indonesia, and also found evidence of recent hydrothermal activity and epithermal sulfide mineralisation.

Jan 1, 2004

In setting out to describe the methods and machinery employed at Iron Knob the writer does not attempt to give any information as to the situation, topography or geological features of the locality. This, together with estimates of the quantities of ore still available, has been carried out in a most thorough manner by R. L. Jackr and F. R. Hockey. This essay is intended to deal with working methods as they exist to-day, beginning with drilling, blasting, quarry traction, etc., and touching on such details as the supplyof electricity, water and compressed air.At the present time almost the entire output of ore is won from the hill known as Iron Monarch. The form of the hill, a smooth, rounded dome, rising some 640 ft. above the plain and having a base diameter of n miles, lends itself ideally to the "bench" system of open-cut quarrying.Fig. 1 shows the relationship of the benches "A," "B" and "E" in their order of development. Bench "E" is at present the principal working, but, as the greater part of the ore above this level has now been removed, bench "A," some...

Jan 1, 1936

The Waimumu area, 12 km southwest of Gore, is underlain by the Gore Lignite Measures, an early Tertiary fluvial sequence approximately 500 m thick resting on Triassic-Jurassic argillitic basement. The Waimumu Quartz Gravels (Pliocene) have been deposited locally and are in part due to the localised reworking of the Gore Lignite Measures. Structurally the area is dominated by the Dunsdale Fault System, a steeply dipping series of NE trending reverse faults (Isaac and Lindqvist, 1990). The Belle-Brook, Hedgehope and Parker Road sites sampled are adjacent to the downthrown (east) side of the Hedgehope Fault.The authigenic gold-sulphide association at Belle-Brook was discovered in 1987 (Falconer, 1987: Clough and Craw, 1989). Despite a very limited amount of alluvial mining a significant quantity of authigenic marcasite has developed. Authigenic sulphide trace element analysis has shown anomalous amounts of As, Ni, Cr and to a lesser extent Zn, Pb and eu (Table 1). It has been established that the nickel occurs as a colloform banded Ni sulphide, possibly bravoite, within the marcasite (Figures 1 & 2). Arsenic and nickel (re)mobilisation are well documented in the literature. Generally As and heavy metals are mobilised in the groundwater as a result of the oxidation of sulphides (ie as a result of mining). At Belle-Brook it is reasonable to assume the authigenic sulphide trace element composition reflects either localised groundwater contamination or hydrothermal mineralisation. This poster presents some preliminary findings.

Jan 1, 2001

A consideration of mining ventures and the changes of an environmental nature that occur. The paper is introduced with a general statement claiming recognition that mining ventures are important to human well-being but that these need to be justified against the environmental changes that they bring about. The various factors that need to be considered are cited followed by an historical review of mining activities. The various environmental issues are discussed under three headings; socio-economic, physical and biological, prior to reviewing the world's demand for minerals including fossil fuels. In conclusion guidelines for appraising mining ventures relative to environmental changes that may occur, are given.

Jan 1, 1981

In the latter half of 1973 a contract was given to Roberts-Holland Joint Venture for the stripping of the southern exhaust airway.The contract was carried out efficiently and relatively cheaply. It was completed 2 months ahead of schedule.The sinking stage and in particular the drilling jumbo proved to be a success and helped produce an above schedule stripping rate.No major problems were encountered with ground conditions or ventilation. A survey of the shaft showed the diameter to be within the set limits of 5·49 m ± 0·15 m.

Jan 1, 1974

By Tripathy A. K, Satapathy B. K, Nayak B, Mohanty J. N, Dey D. N

The paper deals with the metallographic tudy of heat treated chromite and chromite-coke composite briquettes. The briquettes, prepared from chromite concentrate of Orissa Mines using molasses-lime, dextrinelime and tamarind seed as binders, were subjected to different temperatures and examined metallographically. The change of phase with temperature was analysed by X-ray diffraction.

Jan 1, 1987