Search Documents

In common with general experience in the iron-making industry overseas, Australia has in recent years suffered a deterioration in the physical quality of her iron ores in their suitability as a direct blast furnace feed. The increasing amounts of fines and the more friable nature of lump ore, especially in the ore from the Cockatoo Island deposits in Yampi Sound, Western Australia, have focused attention on problems of ore preparation and agglomeration, particularly sintering.Although very small pilot scale Dwight-Lloyd type sinter machines were operated at the steel-making centres at Newcastle and Port Kembla during World War II, no sizeable capacity was installed, so that ore was charged to the blast furnaces almost entirely unscreened, and the resultant flue dust was stockpiled.Towards the close of the war, the pilot plant at Newcastle was replaced by a small machine, adjacent to the flue dust stockpile, with a rated capacity of some 20 tons per hour. After approximately five months of part-time operation, this plant was closed down in January, 1945. Production was not resumed until December, 1950, when, due to a temporary ore shortage, it was decided to supplement available ore with sinter produced from the large flue dust stocks of about 300,000 tons. In spite of mechanical and process difficulties, inherent to the design of the plant, operation was continued on a two-shift basis, with several shutdowns for extensive overhaul and plant alterations, until September, 1954, when production was put on a three-shift basis. Addition of Yampi ore fines to the sinter machine burden was not commenced...

Jan 1, 1957

By L Ventura, M Almond

The Pueblo Viejo project in the Dominican Republic installed an innovative sample system on its reverse circulation (RC) drilling rig during commissioning and subsequent commencement of operations. As knowledge of the orebody increased with mining and plant production, cost pressures became apparent that raised questions concerning the continued use of RC drilling versus blasthole sampling for ore control.To justify the continued use of RC drilling for grade control, an in-depth study was undertaken to determine the quality of the sample and prove its value-add to the operation.To investigate the differences in sample quality, a complete bench trial was initiated across both ore pits to compare RC drill results with blasthole assays on a side-by-side basis. The results indicated that based on ore block comparison between RC and blasthole sampling, RC identified an additional 20 per cent of high-grade (+ 4.5 g/t Au) ounces.Previous work indicated that Au, Ag and Cu were all elevated in the drill fines at Pueblo Viejo (Goers and Almond, 2012). This previous test work did not consider the quantity of fines in an RC sample therefore new test work was undertaken to include particle size distribution analyses. This study would determine if the inclusion of fines in the sample was occurring and compare the quantity of fines in the sample against other sample systems and blasthole samples.Comparisons between RC samples and blasthole samples indicate that for the RC samples a range of 30–35 per cent of the sample passed 300 mesh as compared to blastholes where the range of the sample passing 300 mesh was 15–30 per cent.This paper includes a case study on the importance of accurate samples and how they have impacted throughput through the pressure oxidation process plant at Pueblo Viejo. The accurate samples provided by RC allow for improved stockpile and blending strategies, showing the importance of accurate samples to manage risk and create value, against the perception that savings can be made at the risk of poor sampling performance.CITATION:Almond, M and Ventura, L, 2017. Adding value with reverse circulation drilling at Pueblo Viejo, in Proceedings Tenth International Mining Geology Conference 2017, pp 277–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

Knowledge of true block grades is obtained from a mathematical model of an orebody, simulated with sample grades normally distributed and spatially correlated according io a spherical semi-variogram model.The superiority of kriging to the polygonal method of estimation is demonstrated on this modelled deposit by comparing the true values with the kriged and polygonal estimates obtained from sampling the deposit. Finally, selection of blocks of the deposit on the basis of the estimated values, shows that if kriging is used, what is predicted is largely mined, whilst if the polygonal method is used large biases can occur depending on the position of the cut-off grade.

Jan 1, 1978

Since its inception in 1962, the Julius Kruttschnitt Mineral Research Centre has adopted the view that an effective method of training highly qualified engineers for the mineral industry is the pursuit of postgraduate research programmes conducted in operations, that is, in the mines and processing plants of the industry which the research serves. The paper describes how this is achieved in practice, at little or no cost to the taxpayer, and explores the strengths and weaknesses of this approach in the context of a dual mission for the Centre: 1. The postgraduate training of engineers for the mineral industry. 2. The production of useful R &I) for the mineral industry. Topics discussed include financing, relationships with industry and Government, the maintenance of academic excellence, research style, the marketing of research, and limits to growth.

Jan 1, 1989

By D R. Andrew, K T. Morrison, J F. Tiedgen

Waste blasting in iron ore operations can pose a number of technical challenges, including blasting through variable geology and blasting soft ground in wet conditions. Blast patterns are designed to be loaded with a specific range of explosives with unique characteristics and properties. Each explosive product will produce an optimal blast outcome for a given set of blast parameters and ground conditions. Sites characterised by softer rock typically require low-density, low-energy explosives. Historically, these products have contained a high ratio of porous ammonium nitrate prill and are only suitable for dry blastholes. When blastholes within a pattern are found to be unsuitable for such explosives due to wet, damp or muddy blasthole conditions, a new product is selected. While it is easy to switch products to match blasthole conditions, the different properties of the new non-ideal product can impact blast performance and increase loading times and costs.Flexigel™ is a solids-sensitised emulsion blend suitable for loading at variable densities and energies in dry, damp, muddy or wet blastholes. It is a universal product that can be loaded to match ground and blasthole conditions or complement other explosive products.At Fortescue Metals Group’s Cloudbreak site, Flexigel™ was trialled through a series of matched pair blasts in order to optimise blast outcomes in conditions that were non-ideal for existing explosive products and to reduce the overall cost of drill and blast operations. Flexigel™ yielded improved instantaneous dig rates and improved loading efficiency when compared to a traditional emulsion blend. The results also indicated that variable-density and variable-energy products afford greater flexibility for optimising blast outcomes across all ground and blasthole conditions trialled.Trials of Flexigel™ at Cloudbreak have shown that a variable-density solution is available for conditions where traditional explosive products are non-ideal. As such, Flexigel™ is able to fill a major void at any operation where the desired low-density, low-energy explosive product must be substituted for a more expensive traditional emulsion blend or heavy ammonium nitrate/fuel oil.CITATION:Andrew, D R, Morrison, K T and Tiedgen, J F, 2015. Flexigel™ – a variable-density solution, in Proceedings Iron Ore 2015, pp 413–418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

This is what I term ... the graveyard end of any Conference. It's almost over. Those of you remaining are either all talked out or past the information overload stage. And some of the sensible? ones have left for more exciting field trips, or gone back to their work-site where they earn their daily crust, or headed off South to another Conference of interest to the Energy sector that is being held currently in Christchurch. But that's OK. I have a thick skin! And neither am I particularly Politically Correct! I am not a miner: I am not involved in the mining industry in a hands on way at all. I am not even an academic. I am not even too sure why I am here ... apart from the fact that I agreed to come! At various times in my life I have been a D istrict Councillor, Chairman of a Regional Council and even an MP. I am a supporter of responsible mining.  All of what I have to say is my own point of view rather than that of either the Coal Producers' Federation or the mining industry. That is not to say that we are often in agreement, but I thought I would clear that point right at the outset. And some of what I will talk about will not strictly be to the topic - it's hardly mind-bending riveting stuff. Well, is it? But obviously because you are still here you have some interest in the topic.

Jan 1, 1997

Polyacrylamide flocculating agent has been used in the Leaching Division 'of the Risdon Works of the Electrolytic Zinc Company of Australasia Limited since October, 1960. The number of thickeners in the continuous thickening stage was thereby reduced from eight to three. There has been an increase of 25 per cent in throughput and a reduction of solids in thickener over-flow from 3-4 g/l. solids to 0·5 g Ir. solids. Reagent addition has been at the rate of 0·25 lb Separan NP10 per ton solids.Additionally there has been a gain of 3 per cent in current efficiency as the direct result of the addition of Separan NP10 to purified cadmium sulphate solution priOl; to electrolysis for cadmium metal. A smoother deposit has resulted and it has been possible to increase deposition time between strippings from 47 to 71 hr. However, there has been a slight increase in the lead content of the cadmium metal produced.The use of Separan NP10 to settle copper bearing residue in a batch process stage has resulted in a five-fold increase in settlement rate and a reduction in purification cycle time.INTRODUCTIONThe Electrolytic Zinc Company of Australasia Limited, Risdon, Tasmania, produces zinc by electrolysis of purified zinc sulphate solution, the raw material being zinc sulphide concentrate. In the Risdon process (Van Arsdale, 1953; J ohnstone, 1953; Ross, 1949) the compound zinc ferrite (ZnO.Fe203) is formed during the concentrate roasting stage. When the roasted material is leached in dilute sulphuric acid the zinc ferrite is not attacked, and it remains as part of the insoluble leach residue, of which it may form as much as two-thirds of the whole. The remainder is mainly unroasted zinc sulphide, unleached zinc oxide, lead sulphate, gypsum, silver compounds etc. The zinc in the residue may be 10 per cent of that in the original concentrate.Continuous thickeners are used to recover the valuable residue from the impure zinc sulphate solution and the...

Jan 1, 1963

Since the last occasion on which I spoke to you on this subject there has been a considerable increase in the mechanical ventilation of Western Australian mines.The following table compares the figures for 1939 with those of 1941. The type of fan most commonly used is the limit load fan. On account of its higher mechanical efficiency it has very largely superseded the multivane fan with forward curved blades.Two fans of the propeller type are in use and these have given very satisfactory service. This type of fan also has a high mechanical efficiency particularly at the correct duty for maximum efficiency.The maximum efficiencies obtainable from the various types are, for "multivane" 670/0, for "limit load" 75%, and' for aerovane 7810/0.References to propeller fans with variable pitch have appeared in the technical press, but no detailed d~scription has been issued. The advantages of these fans for mine ventilation are not obvious. An aeroplane is required to operate over a wide range of duties, while the speed of the motor for maximum efficiency is pl'actically constant. In such circumstances the propeller can be adapted to the particular work it has to do by varying the pitch of the blades. In a mine the speed of the fan can be varied to suit.the conditions, and it would appear that variable pitch is not necessary while there is a reasonable range of fans to choose from.The question of the correct position for the fan still comes in for considerable discussion. Exhausting fans at the surface have the support of time and custom, and in many cases this represents the only reasonable arrangement. Such fans should be fitted with an evase, especially in the case of fans with a high outlet velocity such as the aerovane types.It is claimed that there are advantages in having the fan at the surface where it is readily available for inspection and maintenance. Experience has shown that these advantages are more apparent than real. Fans will run for long periods with no attention other than occasional greasing and cleaning, and modern electric motors will run without attention for very long periods.In some instances the expense of a power cable to take current to the fan may be saved by placing it on the surface, but in the majority of cases...

Jan 1, 1941

Valuable Components Recovery from Lead-Zinc Metallurgical Slag

Sep 13, 2010

The upper amphibolite-grade mctasediments of thc rinaroo area, North Queensland, form part of a regional aurcole to the large Tinaroo Batholith and are the stratigraphic equivalents of the Hodgkinson Formation of gencrally low metamorphic grade. There is no evidence of any lithological unconformity.The higher grade metasediments have a more complex deformation history than is typical for thc surrounding region and this may bc due to one or a combination of two factors; an additional strain componcnt associated wilh the intrusion of Ihe Tinaroo Batholith, or a more marked finite strain response to the overall regional stress field within hotter. more ductile rocks.Four deformational events can be characterized within Ihc Tinaroo Area. Close to Ihe Tinaroo Batholith D1 and D2, arc so strongly developed that they disrupl the continuily of Ihe original Iithological layering. In the aureole region, D1 is strongly overprinted and its original fabric intensity is obscured, but both D2 and D3 display a mappable decrease in intensity away from the granite margin. These three deformations occurred during Carboniferous or early Permian time. D4 is later and only patchily developed.The broad, moderate pressure metamorphic aureole surrounding the Tinaroo Batholith is a typical of the CairnsCooktown group of Permo-Carboniferous granitoids. which usually develop narrow, lower pressure contact aureoles. Two periods of metamorphism are distinguishable. The first reached peak temperatures somewhat greater than 520°C, the second temperatures around 620-630° C immediately adjacent to the granite contact.Several cale-silicate lenses containing scattered scheelite mineralization occur within the area. Scheelite appears to have crystallized at the same time as the cale-silicate minerals, its appearance coinciding with the intrusion of the Tinaroo Batholith. Unlike many "skarn-type" scheelite deposits, the scheelite-bearing cale-silicates are Fe-poor, with no positive correlation between total Fe and W.

Jan 1, 1982

By T Mattiske

The Fimiston Open Pit (commonly referred to as the æSuper PitÆ) is a part of the Kalgoorlie Consolidated Gold Mines Pty Ltd (KCGM) operation in Kalgoorlie-Boulder. KCGM manages the Fimiston Open Pit, the Mt Charlotte underground mine, the Fimiston Mill and the Gidji Roaster for its Joint Venture Owners, Newmont and Barrick Australia. KCGM produces up to 850 000 ounces of gold per year. The KCGM operations are located on the historical Golden Mile on the outskirts of the City of Kalgoorlie-Boulder, about 600 kilometres east of Perth Western Australia. This traditionally underground mining centre has been worked since 1893, yielding in excess of 50 Moz of gold from ore with an average head grade of 10 g/t. This represents approximately ten per cent of the gold produced in Australia and one per cent of the gold produced in the world. The Fimiston Open Pit is essentially an aggregation of what were known as the Judd, South, Paringa, Croesus/Eclipse, Central, Brownhill, Drysdale, Morrison, North and Horseshoe pits into one continuous large-scale operation. The old Fimiston Underground Operations (included the Main, Croesus, Chaffers, Lake View, and Perseverance shafts) were also located within the area of the Fimiston Open Pit. The underground operations closed in 1992 due to high mining costs.

Jan 1, 2002

Reason Analysis of Impurity Containing and Technology Discussion of Quality Improvement for Low-Quality Iron Concentrate

Sep 13, 2010

The optimal production of the metals needed by society is best achieved by a close synergy between concentrate production and smelting. For over 75 years commencing in 1923, such a close relationship was enjoyed between the Sullivan Mine in Kimberley, British Columbia and the Trail zinc-lead complex. An effective program of continual change and improvement at the Sullivan concentrator was achieved through a strong entrepreneurial spirit. This spirit was in part maintained through a favourable location in south-eastern British Columbia that resulted in a dynamic local community that has survived the closure of the mine. Innovations to be reviewed include feed forward reagent control, the use of column flotation to zinc and lead cleaning and the application of ultrafine grinding coupled with concentrate dewatering using hyperbaric filter technology.

Jan 1, 2005

The area around Big Bell was actively explored and sporadically mined for gold from 1904 onwards. The lease was named Big Bell in 1913. The property became established as a major mining centre with the development of the Big Bell underground mine in 1936. Mining operations commenced in late 1937 and ceased in January 1955, after milling 5.56 million tonnes of ore and producing nearly 21 tonnes of gold. In 1969 Australian Consolidated Minerals Ltd (A.C.M.) acquired the deposit then explored it alone and in joint venture until the current joint venture agreement with a subsidiary of Placer Pacific Limited (PPL) was negotiated in 1984. Following exploration and evaluation of near surface mineralisation, and a reassessment of the remnant pillars underground, the concept of a large open pit in conjunction with an underground mine evolved. The feasibility study was completed in October 1987, and the decision to go ahead was formally announced on 2nd December 1987. Placer Dome Technical Services Ltd were contracted to be the Project Managers, commencing construction on site early in January 1988 and handing the plant over to the operators 13 months later. The capital cost of the project at handover was estimated to be $133 million. The operating team commenced pre-production stripping of the open pit on 1st May 1988. By 31st January 1989 almost 16.0 million tonnes had been stripped and 350,000 tonnes of ore stockpiled.

Jan 1, 1989

By A Mortazavi, M Akhmedya

Mining is recognised as being one of the most dangerous industries in the world due to the difficult working conditions. Working in such hazardous circumstances in an underground mine often results in a variety of accidents. The working conditions at Kazakhstan’s underground mines have deteriorated owing to a lack of a risk-reduction plan and methodology. This paper evaluates different underground mines in Kazakhstan and demonstrates the employed mining method and the observed failure modes. Risk assessment has long been recognised as a valuable technique for preventing accidents. In the underground mining sector, risk assessment tools play an important role in avoiding work-related accidents. However, geotechnical uncertainty is a significant source of severe incidents like stress-induced roof collapse, wedge failure, seismicity etc, which result in human and financial losses. A geotechnical risk assessment performed early in the mine design process might assist justify a different mine design component, such as different support systems for a dangerous location within the mine openings during mining. The goal of this research is to create a damage/failure database aiming at the development of a geomechanical risk assessment methodology. This work identifies a thematic structure linked to risk assessment and management for the examined Kazakhstan mining sector. As part of the developed database, the dominant modes of failure within the Kazakhstan underground mining conditions were investigated. The study will provide opportunities to establish future research objectives for Kazakhstan’s mining industry where there are significant gaps between state-of-the-art research and mining operations in practice.

Nov 29, 2022

By J L. Maule, S J. Mathews, K A. Rodgers

Gold and Silver bearing epithermal veins of the Golden Cross deposit are hosted in Miocene and Pliocene calc-alkaline volcanics occurring 8 km northwest of Waihi at the southern extent of the Coromandel Peninsula, North Island, New Zealand. Veining occurred during a period of hydrothermal activity that began early to late Pliocene, and possibly continued into the Pleistocene.   Field relations and petrographic relationships reveal that multiple generations of FeS2 occur in the Golden Cross region, with FeS2 occurring in all nine rock types recognised at Golden Cross. The variability of FeS2 morphology was investigated by preparation of high purity FeS2 separates, and grain counting. Marcasite is the dominant FeS2 phase at Golden Cross, and along with pyrite is shown to have a systematic habit variation. Pyrite shows a sequence from cubes through octahedra to pyritohedra to dendritic growth. This pyrite sequence conforms to an experimentally determined sequence. The parallel sequence for marcasite at Golden Cross is from tabular through bladed aggregates to euhedral miscellaneous marcasite morphologies. The FeS2 sequences observed are believed to be due to increasing temperature, and perhaps also increasing FeS2-oversaturation and fluid flow.

Jan 1, 1994

By Y Ren

?ptim?sgtion t?ols nos ope? 0iu ?ingc s?ch as the cche??ling and?pi? k?(i?isatTon tool{ ?ave bg?ome(?osd-dvfective way? to e?iluata open`¦it mi~e!p?n?ept as w?ll asá?}prmv?ng mine?projecW`value> ?owerez

Aug 12, 2013

By P K. Smith, N G. Corner, R J. Ryan, D C. Arne, F P. Bierlein

The Reefton Goldfield has produced 67 t of gold from mesothermal vein gold deposits in metasedimentary rocks of the Greenland Group (Cambrian-Ordovician). The Globe-Progress deposit contributed 13.2 t (418,000 oz) of this total, predominantly from quartz veins. Recently a resource of 14 Mt at 1.96 g/t Au (27.5 t or 882,300 oz of contained gold) has been delineated at Globe-Progress in quartz vein remnants and disseminated within adjacent sedimentary rock, much of which has been locally brecciated. The breccias consist of quartz vein and sedimentary wall rock fragments set in a matrix of clay ærock flourÆ and sulphide (arsenopyrite plus minor pyrite and stibnite). Gold, closely associated with sulphide, is disseminated within the breccia. Disseminated gold also occurs in massive siltstone and sandstone adjacent to the quartz veins and breccias. Exploration drilling at Globe-Pogress, and several other Reefton prospects (e.g. Capleston, Merrijigs, Big River and Alexander River), has intersected zones of disseminated arsenopyrite carrying up to 20 g/t more gold. These mineralised sediments commonly have little or no megascopic quartz and or carbonate veining. There is little visible indication of former primary or secondary permeability for the passage of hydrothermal fluid and deposition of gold. However, porosity and permeability were formerly present in inter-granular pore spaces and microveinlets now filled with quartz, carbonate and K-mica. The Fosterville gold deposit in Victoria bears many similarities to the Globe-Progress deposit at Reefton, in terms of age, host rocks, hydrothermal alteration and mineralisation style. Many ofthe disseminated deposits in Nova Scotia, including deposits at North Brookfield and Moose River (Touquoy Zone), have similar characteristics to the Reefton disseminated mineralisation, but commonly have abundant pyrrhotite and some deposits have disseminated metal alloy grains of complex metallurgy.

Jan 1, 2000

By B Y. Luan, Y Tian, W Zhou, X Lu, Q X. Cai

The unmanned driving technology in open pit coalmines is an important technology that relies on innovation to drive the development of the open pit coal mining industry in China’s transformation of growth drivers and industrial structure upgrading. It is an important path to solve the shortage of mine truck drivers in the future mining, an important way to improve the working environment of open pit mining personnel, and an important foundation for achieving flexible production capacity in open pit mining to cooperate with the coordinated development of new energy. The communication rules at intersections are key to ensuring the safety and efficiency of unmanned driving in open pit coalmines. This paper proposes a collaborative traffic strategy between unmanned trucks for the single bucket unmanned truck intermittent process system in open pit coalmines. Based on the gap theory, this paper analyses the conflict characteristics and establishes a coordinated traffic strategy for the common intersection and merging conflicts of unmanned truck trucks in open pit coalmines, A multi-agent system simulation platform was built to evaluate the coordinated traffic efficiency under different initial average gap sizes of vehicles, with intersection traffic density, vehicle speed, and gap changes as key indicators. The results show that under the simulation conditions of this article, when the initial average gap of vehicles reaches three (four) times or more of the safe distance, the coordinated traffic performance of intersection conflicts (merging conflicts) is better, and the traffic capacity of intersections is close to the traffic capacity without conflicts.

Sep 1, 2024

By S Jahanshahi

In an earlier LCA study, the authors showed that the electricity consumption of the electric furnaces used in the production of the ferronickel and ferrochrome feedstocks made significant contributions towards the Gross Energy Requirement (GER) of stainless steel production, on a æcradle-to-gateÆ basis. Given the relatively low efficiencies associated with electrical power generation, substantial reductions in the GER for stainless steel production could be anticipated if more direct use of thermal energy was made in the ferronickel and ferrochromium smelting stages.In view of these findings, a follow-up study was undertaken to investigate the likely environmental benefits of using bath smelting processes for the production of ferronickel and ferrochromium compared to the traditional rotary kiln-electric furnace processes, but still utilising the electric furnace process for stainless steel production. The METSIM process simulation software package was used to set up models of the two bath smelting processes and provide process energy requirements that were incorporated into the LCA. The environmental impacts considered in the LCA were greenhouse (Global Warming Potential, GWP) and acid rain gas (Acidification Potential, AP) emissions and solid waste emissions.The results of the study showed that the bath smelting route reduced the GER for ferronickel production by about 37 per cent over the traditional route, which translated to about a 21 per cent reduction in the GER for stainless steel. The corresponding reduction for ferrochromium was about half that for ferronickel, and when combined with the ferronickel result gave a 25 per cent reduction in the GER for stainless steel production. Similar reductions were also observed for the GWP and to a lesser extent the AP for both feedstocks, as all primary energy inputs were essentially fossil fuel based. Substantial reductions in solid waste emissions were also indicated for the direct use of ores in smelting. By utilising bath smelting processes for the production of the ferronickel and ferrochromium feedstocks, stainless steelÆs suitability for meeting many of the goals necessary for sustainable development, already recognised because of its particular properties, would be even further enhanced.

Jan 1, 2004