Search Documents

By Lawson F

Arsenic-containing waste was dissolved into molten slags and the leaching behaviour of the quenched arsenic-doped slags (containing up to 2.3 wt per cent arsenic) was ascertained to evaluate the potential of this method as a means for arsenic disposal. The leaching behaviour was evaluated using acetic and sulphuric/nitric acid based solutions.From short-term (18 hour) leach tests, the amounts of arsenic in the leach solutions were found generally to decrease with an increase in the Fe(III)/Fe(total) ratio of the slag or an increase in pH of the leach solution. The amount of arsenic in solution increased with an increase in the slag basicity, the slag arsenic concentration or the surface area of the slag exposed to the leach solution. From longer term leach tests (up to 40 weeks) in the pH range 5 to 8, the arsenic remaining in the leach solution was believed to be controlled by sorption processes. The sorbent was an iron oxide-rich material which had the capacity to lower the arsenic concentration in the leach bottles to well below 1 ppm in some cases. At a leach solution pH over 9, the arsenic concentration in the solution increased with time, although the rate of solubilisation was much slower due to the high pH.Slags have the potential to stabilise arsenic and prevent it entering the environment provided attention is paid to the slag chemical composition and oxygen potential.

Jan 1, 1996

By M Chen, W S. Ng, Y Liu

In the processing of refractory gold-bearing sulfides, pressure oxidation (POX) is commonly known for its role in liberating the gold in solid-solution via oxidation of the sulfide occlusions. For deposits that contain arsenic-bearing species including arsenian pyrite and arsenopyrite, POX serves an important secondary function in the fixation of arsenic, via the hydrothermal precipitation of stable arsenates such as scorodite and basic ferric arsenate sulfate (BFAS). There have been various investigations on the impact of different POX conditions on arsenic precipitation and the stability of the formed phases, but less is known about the changes to the arsenic carrier that occur in the curing stage, which follows directly from POX. The primary function of curing is to coax the dissolution of sulfates to reduce lime consumptions during cyanide leaching, and the slurry is kept at elevated temperatures near 100°C to achieve this. While the arsenic-bearing phases are expected to undergo transformation during this stage, there has thus far been limited experimental evidence. In this study, the effect of curing time and curing temperature on the arsenic-bearing species and arsenic deportment in the POX product has been investigated. Leaching of the curing products was also conducted to examine the stability of the arsenic species in the solid precipitates.

Aug 24, 2022

By D Giurco

This paper presents the results from research undertaken in the CSIRO-funded Mineral Futures Collaboration Cluster on developing a future vision for the mining and minerals industry – Vision 2040 – in which the industry proactively contributes to long-term benefit for communities and the nation. Our research finds that Australia is currently experiencing mining-led prosperity due to high commodity prices, yet underlying this are challenges for maintaining market share due to lower productivity from extracting lower grade, more remote and complex ores. Whilst much focus has been on developing new technologies for finding and processing such ores, this paper assesses these activities, together with policy and market innovations in the context of needing to strengthen social, environmental and financial capital for long-term benefit. Vision 2010 sees mining activities linked to systems that are net providers of clean water, energy and ecosystem services, rather than minimising negative impacts alone; sovereign wealth funds are used to harness current prosperity for future innovation. Using a case study in lithium and comparisons to iron/steel, coal and copper – we illustrate the opportunities for new technology, policy and market innovations to link the mining and minerals sector in Australia to more sustainable patterns of production, consumption and prosperity.

Nov 22, 2011

By A J LYNCH

It was Harold McMillan, Prime Minister of England 30 years ago, who used the phrase "The Wind of Change" to describe political events in Africa in his day. So well did this phrase capture the spirit of the time that it echoed around the world, and the echo has never stopped. Change is the constant factor in the society in which we live and everyone of us has had experience of the effect which it has had on our professional and personal lives. Change will not stop, it will continue at an increasing rate and the questions we must answer are how do we prepare ourselves to meet the challenge of future change and how do we take advantage of the opportunities which it will bring? It is these questions which I wish to discuss in this address.

Jan 1, 1989

Cobar Mines Pty. Limited (CMPL) uses sodium sulphite as the principal depressant to attain selectivity in copper flotation prior to sequential recovery of lead and zinc. The usage of sodium sulphite is examined both from a theorectical viewpoint ana from the manner in which the copper circuit at (MPL has developed. The results of relatively recent investigations, both in the laboratory ana the plant, are discussed aria shown to support the present operating Techniques.

Jan 1, 1983

By R Winterberg

Concrete is a well established and reliable construction material for the permanent lining of tunnels, but shows some weak performance characteristics, which can be overcome by the addition of specialised fibre reinforcement. This paper addresses the particular performance design requirements of segmental linings, discussing the improvements of fi bres on concrete properties. Focus is made on the beneficial effects of fibre reinforcement on the cracking behaviour and the toughness performance, providing a safe and durable tunnel lining.Not only the mechanical performance of fibre reinforced concrete (FRC) for segmental linings, but also the durability of the linings has gained growing attention among the designers and consultants. Especially tunnel linings with exposure to media with corrosion potential, such as wastewater sewer tunnels or desalination plant outfall tunnels, have high requirements on their durability. The design of these structures must provide a comprehensive study of durability aspects. Fibre reinforcement can substantially improve the durability of concrete.Research has been carried out on the cracking behaviour of concrete. The beneficial effects of steel fibres on the cracking behaviour reduce the permeability by reducing the flow paths within the concrete. Crack bridging steel fibres create necking effects in bending cracks, leading to earlier closure of the cracks. Further, steel fibres create particular crack formations, which lead to a substantial reduction of the fl ow rates through separation cracks. The results also show that considerable cost savings can be achieved using FRC, as the thickness of the linings can be reduced.The durability design issues will be addressed and underlined by a case history on the Hobson Bay sewer tunnel in Auckland, New Zealand.

Mar 8, 2011

The Bellambi Coal Company Limited com menced longwall mining at South Bulli Colliery in 1965. At present it operates three long- wall units in two seams. Although results to date have been less successful than planned, it is apparent that this type of mining has tremendous potential in the particular conditions at South Bulli. Massive sandstone strata above the Bulli seam is the controlling influence on face conditions. The earliest equipment proved to be inadequate and the Company has progress- ively replaced and upgraded the roof supports and ancillary equipment so that the present units are capable of producing high and consistent outputs.

Jan 1, 1976

Based on the idea to copy crystallisation and precipitation phenomena occurring in nature, a new technology was developed allowing the preparation of metastable, mineral forming solutions. If these solutions are brought into soil or rock formations, directed precipitation of slightly soluble minerals takes place. Immobilisation of dissolved heavy metals as well as overlaying of reactive mineral surfaces with insoluble minerals can be achieved. It is possible to prepare solutions leading to the formation of gypsum, BaSO4, CaCO3, Ca(OH)2, Al(OH)3 or Fe(OH)3. The successful large-scale application of BaSO4 forming solutions was demonstrated in the former uranium mine Koenigstein of Wismut GmbH, (Germany).

Jan 1, 2003

By Buizen M

An investigation into the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces has been completed by the Subsidence Engineering Section of the New South Wales (NSW) Department of Minerals and Energy. Changes in strata bulk permeability were also measured by standard packer tests undertaken before and after mining. The strata movement was measured by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were collected to suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors did not move significantly until the face went past the borehole. For subcritical extraction geometry with the extraction width to mining depth ratio of 124, the caving zone extended to roughly 9 times the extracted seam thickness above the seam roof. Tensile strains within the overburden tended to be much more closely related to stratigraphy than to the proximity to the extracted seam roof. Larger tensile strains were associated with layers of sandstone, siltstone and conglomerate, whereas layers of mudstones, claystones and coal underwent much smaller strains indicating subsidence in blocks. A beller correlation was observed between pre-mining Rock Quality Designation and permeability than between rock type and permeability. This correlation was less evident in the post-mining core logs. There was an overall increase in bulk permeability after mining.

Jan 1, 1990

Every text book for blasting in Japan says that Hauser's law can be applied for practice. But recently it came true that there was no historical record about him and no actual datum of his own or other's to testify. According to his theory, the funnel ratio N = r/W in crater test is inversely proportional to the rock strength and proportional to the explosive amount: where r is the radius of crater and W is the burden. But experiment showed the opposite result, and revealed new information. Two kinds of experiment, crater test and boulder blasting of mortar, were carried out to investigate the effects of rock properties on blasting. The material used for test 1 and test 2 was a mortar block (60cm)3 cube, 4 vertical faces of which were used for crater test. The results from Test 1 and test 2 were summarized as follows. The funnel ratio ranges between 2.5 to 4.5 in proportion to rock strength and burden. The standard ratio of 1, reported by Hauser, was not observed in any instances. It was also noted that the funnel ratio is independent of the explosive amount. The material used for boulder blasting, test 3, was a mortar block (40cm)3 cube, in the middle of which was located a vertical borehole for the explosive charge. The results of test 3 were as follows. The necessary explosive amount for boulder blasting is in inverse proportion to the mortar strength. Fragmentation and throw are proportional to the mortar strength.

Jan 1, 1990

By Anderson C. G

The design of crawler-mounted conveyor belts installed for the handling of brown coal in open cuts is described.INTRODUCTIONThe State Electricity Commission of Victoria operates two brown coal open cuts at Yallourn, Victoria. The larger of these cuts produces n million tons per year of brown coal containing 67 per cent. moisture, and the smaller, at Yallourn North, produces 1-1 million tons of coal, with a moisture content of 50 per cent. A further open cut at Morwell with projected output of 9-10 million tons per year is in the course of development. In the larger Yallourn open cut coal is excavated by means of conventional bucket chain and bucket wheel dredgers and transport is by electric locomotives and saddle bottom trucks running on 90 cm. gauge railway tracks. At Yallourn North, coal until recently has been largely won by 3i and 5 cu. yd. electric shovels and transported by large diesel-enginedmotor trucks. The difficulty of keeping these trucks in operation during the winter periods owing to the v.ery wet conditions and the high cost of maintenance of these vehicles led to the introduction of a moving face conveyor system.EXISTING CONVEYOR INSTALLATION AT YALLOURN NORTHA conveyor system employing a 36-in. belt running at a speed of 400 ft. per minute and having a nominal capacity of 425 tons per hour with 50-h.p. drive units, was selected as appropriate for the output of the open cut. The conveyor structure adopted was a standard type as used in under...

Jan 1, 1955

By Coates D. F, Neil T. J, O&apos

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risks of slope fail- ure inherent in steeper slope angles. However, no formal framework for a proper analysis existed to date. This paper describes the results of the past four years' effort in which a formal eco- nomic analysis framework was developed and tested through a case study. This framework, in essence, consists of the availability of tested procedures and com- puter programs. The procedures as well as the programs are divided into two broad functional categories; (1) the first category related to assessing the economic benefits and costs associated with various pit slope angles and (2) the second category that determines the overall financial impact which the assessed benefits and costs exert to the mine operator's overall economic stature.

Jan 1, 1977

The Olympic Dam copper-uranium-gold-silver deposit, located approximately 520 km north-northwest of Adelaide, South Australia (Figure 1) was discovered in 1975 by Western Mining Corporation. A joint venture to facilitate development of the deposit was formed in mid-1979 between WMC (51 per cent) and the British Petroleum Group (BP, 49 per cent). Production commenced in 1988, and current annual output from the mining and treatment of 2.2 Mt of ore is approximately 65 000 t of refined copper and 1400 t of uranium oxide. Significant amounts of refined gold and silver are also produced.

Jan 1, 1993

The ore mined from the Lead Lode of The Zinc Corporation leases consists of a fairly granular mixture of galena, marmatite, chalcopyrite, tetrahedrite, pyrrhotite, pyrite, and lollingite with a gangue association of calcite, quartz, bustamite, rhodonite, mangan-hedenbergite, garnet, fluorite, mangano-calcite and apatite. The silver content of the ore occurs in three minerals tetrahedrite, dyscrasite, and pyrargyrite, the last two mentioned occurring in microscopic association only. Other metallic and gangue minerals are also present in this complex mineralogical association, but do not influence the milling operations.Fortunately, the silver minerals favour the galena and chalcopyrite as their host minerals, thus facilitating the recovery of both copper and silver in the lead concentrate. The ore from the Lead Lode assays from 14 - 18 per cent lead; 3.0 - 4.5 oz silver per tonne, and 9.5 - 12.0 per cent zinc.A parallel lode, known as the Zinc Lode, is well developed in The Zinc Corporation leases. This lode assays from six to eight per cent lead, 1.5 oz silver per ton, 18 - 25 per cent zinc with a siliceous gangue. The common Lead Lode gangue minerals, calcite, rhodonite, bustamite - are very rare in present underground exposures. No metallurgical work was done on this ore during the pilot plant operations.The aim in the milling process is to produce:1. A lead concentrate with the maximum economic recovery of lead, silver, gold, copper and antimony, and minimum zinc content.2. A zinc concentrate with the maximum economic recovery of zinc, cadmium, and cobalt, and minimum iron, arsenic and fluorine content.3. A waste residue containing sufftcient granular material to be utilised as underground fill.In considering the economics of the milling practice the above three requirements plus consideration of the tariffs submitted by the purchasers of concentrates were the deciding factors in the evolution of the present milling practice.Towards the end of 1924 The Zinc Corporation Limited added to and adapted the old zinc tailings plant for the treatment of 5000 tons of crude ore per week. This plant, which operated until January 1936, was in general principles similar to the standard Broken Hill methods of ore concentration, whereby the galena was recovered by the gravity concentration methods of jigging and tabling with selective flotation concentration of the residual galena and marmatite. One important difference from other Broken Hill plants was that the primary grinding of the jig tailing was performed with flint-loaded mills operating in closed circuit with revolving screens. Two primary grinding sections were installed, each consisting of two 5 ft diameter by 10ft long tube mills loaded with flint pebbles working in closed circuit with four 3 ft diameter by 3 ft wide revolving screens covered with 22mesh Toncap woven wire screen with 0.57 mm opening. Each section carried a circulating load of 28.3 tons per hour for a jig.

Jan 1, 1994

By A Kleinitz, J Halilovic, K Trappitt

Mine operators use grade control to determine the destination of each block of material in the mine. In polymetallic mines, grades are best expressed in dollars: the Net Smelter Return, NSR, per tonne. To estimate NSRs, geologists working on grade control develop models for each geometallurgical domain in the mine. These models may incorporate observations on the mineralogy and grain sizes of the material being examined. The site’s mill operators contribute to the models by providing geologists with statistical analyses that relate assay results and mineralogical compositions to metallurgical parameters, such as the rates of recovery of each economic metal to each of the concentrates produced, and the compositions of those concentrates. The team responsible for sales and marketing of the site’s products contributes to the NSR models by providing details of the costs of shipping concentrates to smelters and refineries; and by providing figures that are specified in the smelter contracts, such as the payability of the metals in each concentrate and the fees charged by the smelter. The mill operators also provide, for the NSR models, equations to estimate the rates of recovery of deleterious materials to each concentrate. Deleterious materials comprise mostly halogens and amphoteric elements, both of which reduce the efficiency of smelters. Furthermore, deleterious materials such as antimony and arsenic may be poisonous to people and to the environment. The sales and marketing team provide specifics of the penalties that smelters impose upon deleterious materials. These penalties may reduce NSRs by tens of percent, possibly to levels below the cut-off grade. Thus, in the blocks that are subject to grade control, mine geologists monitor not only the concentrations of economic metals, but also the presence and abundance of deleterious materials. The preparation and maintenance of models, to estimate NSRs and to assess changes in the levels of potentially toxic materials to be mined, requires close and continuing consultation between corporate departments. There must be strong communication of mine geologists with the mill operators; with the people who market the mine’s concentrates; and, should there be a risk of encountering toxic levels of deleterious materials, with the mine’s health, safety and environmental officers. This co-operation could require radical changes in the structure of many organisations. However, experience suggests that such changes can significantly improve the profitability of a mine.

Mar 22, 2022

By S Azam

Coal is a vital energy source and source of carbon for metallurgical applications, contributing significantly to the world economy. Coal mining and processing involve multiple processes that generate Respirable Coal Mine Dust (RCMD), one of the primary sources of health hazards for coal workers. Since 2000, the rate of Coal Workers’ Pneumoconiosis (CWP) has continually increased in the U.S, with severity of the cases also worsening. Increasing evidence shows that exposure to RCMD in coal workers is a high-risk factor for lung cancer, which causes more deaths than the following three major cancers combined in the US Recent observations show an increased incidenceof CWP or other lung diseases, particularly among young miners in the Appalachian basin. The CWP prevalence in Appalachia is four times higher than the national average. Although various regulations are in place, the resurgence of such disease among coalminers demands additional efforts to better understand all the possible facets of coal dust toxicity, taking insights from current interdisciplinaryresearch efforts. One such important field is the interaction of coal dust with moisture in underground mines. Although moisture is prevalent and dynamic in an underground mining environment, it has never been evaluated for its impact on modifying the toxicity of coal dust and transport or flow behaviour. However, research conducted in atmospheric sciences in the past decade makes it clear that moisture in the atmosphere can significantly alter the behaviour of mineral dust. This paper is a part of research aimed at understanding how moisture interacts and alters the characteristics of coal dust. Such insight is crucial in understanding the potential toxicity of coal dust and developing mitigation technologies.

Oct 12, 2022

By Shinnosuke U, Zhang HE

In this paper, it is shown that the higher the pre-activation concentration of copper ions in pulp, the larger the adsorption amounts of copper ions and xanthate on arsenopyrite surface, and the better the arsenopyrite flotability in strong alkaline medium. On arsenopyrite pre-activated with cupric ions, the xanthate adsorption density in strong alkaline medium is approximately equivalent to that of cupric ions. It is therefore concluded that an amount of copper ions adsorb on arsenopyrite surface first, and then an amount of xanthate can (and only can) adsorb dependently on the surface active sites produced by these adsorbed copper ions on the mineral, so that arsenopyrite is kept rather flotable and is hardly separated from pyrite even in very strong alkaline medium. Selectively wiping out the surface copper active sites on arsenopyrite is the key point of successful separation of pyrite from arsenopyrite. According to this theory, a new 'SZLI' (know-how) method was recommended to satisfactorily deal with the difficult separation.

Jan 1, 1993

In late 1984, Council of the Australasian Institute of Mining and Metallurgy accepted a proposal to establish a Mineral Heritage Committee. This was to be involved in matters relating to mineral heritage-its recording, its preservation, and the acknowledgement that it can be of use to the mineral industry in the future. The Committee was established to ensure that all of the disciplines of our profession were included and that, so far as possible, all of our country as well as those countries of the Southwest Pacific Basin were represented. Some work has been commenced to bring real- isation of the importance of the heritage of our mineral industry to the forefront of the commu- nity's interest. There is not a state in this country and the Southwest Pacific where the mineral industry has not at various times proved to be the basis of community development.

Jan 1, 1987

I.T.H. Drilling has been accepted as a tool used daily for both production and service work in Australian underground mines. For this reason, it is of interest to examine the rigs and drilling equipment in use to do this work, also to review the technique necessary to ensure that this drilling is done efficiently.

Jan 1, 1978

By Rashleigh C

The selection and application of an effect- ive firing system first require a clear under- standing of the initiating abilities of the com- ponents in such systems. The conditions under which charges can be prematurely initiated by a detonating cord downline must be appreciated. This is a principal consideration in the design of a successful downline/'Anodet'/primer assembly. The advantages and limitations of an electric and several non-electric initiating systems are explained. The factors which in- fluenced selection of the two most suitable systems for use at Isa Mine (viz. downline/ 'Anodet'/primer assemblies and the reinforced long-lead 'Anodet'-type delay system) are dis- cussed. Blasts are detailed in which each of these has been applied. The initiating design for a hypothetical 2 x 106 tonne blast using electric short delay detonators and multi-channel exploders is presented. In this design, charges in remote blastholes are activated after the detonation of earlier firing charges by protecting the firing lines with sandbags.

Jan 1, 1978