Search Documents

By Lunarzewski L, Truong D

Although there are sound principles used in the world recognised methods of gas emission prediction, results based on these methods applied to several Australian longwall extractions have yielded unacceptably high discrepancies. With the development of mining in new seams and at higher rates of extraction, the need has grown for a methodical approach to predicting gas emission levels specifically for local Australian mining conditions. Such an approach is developed from results of recorded emission readings during longwall mining at Appin and Pacific Collieries over the past 6 years.

Jan 1, 1988

In 1972 the Marra Mamba Iron Formation in the Lower Proterozoic Hamersley Iron Province of Western Australia was recognised as a stratigraphic horizon with significant potential for high grade iron ore reserves. Within the Newman area the Marra Mamba Iron Formation has been subdivided into four strati- graphic units: Lower BIF member, Middle BIF and shale member, Upper BIF member and Upper shale member - and a standard natural gamma log reference section compiled for the entire formation. The recognition of the Upper shale member as an additional unit contrasts to the previously proposed stratigraphy. Enrichment of the Marra Mamba Iron Formation to ore grade (0)8 percent calcined Fe) in the Newman area is restricted to the Upper BIF member and to a lesser extent to the Middle BIF and shale member. Typical ore from Orebody 29 is friable interbedded martite-ochreous goethite, signifi aptly different both physically and chemically from the Brockman Iron Formation ores of the Tom Price-Whaleback type. Large scale customer acceptance trials (in excess of 4 million tonnes) have shown that Marra Mamba ore crushed to fines and blended with Mt. Whaleback fines in a ratio of up to 15:85 forms an acceptable sinter feed.

Jan 1, 1981

The series of events leading to the adoption of more complex flotation circuits for coal have been reviewed. In essence, it has been concluded that ac- ceptable overall flotation recovery will only be obtained when efficient distri- bution of collector over all the component feed size fractions is ensured. The achievement of this goal is most likely to be obtained by feed classification and separate flotation of appropriate size fractions. The adoption of such a phil- osophy, however, imposes a number of process problems of both a chemical and an engineering nature. Some of these problems have been identified and possible solutions discussed. A case is emerging for the development of a new generation of flotation cells designed specifically for the flotation of classified coal and for the development of a series of novel re- agents which have the propensity to float middling particles.

Jan 1, 1984

By A F. Idziak

The aim of the present study was an application of coal optical property measurements for analysis of paleostress field existing in fault zones of the Upper Silesian Coal Basin (USCB) during the coalification of organic matter. Measurements of vitrinite reflectance were carried out on coal samples taken near a hanging stope of the Klodnicki fault. Other samples had been taken in vicinity of the Krzyzowicki fault. The Klodnicki fault is one of the main tectonic discontinuities in the northern part of the USCB. It is postulated that its origin is related to the deep-rooted latitudinal discontinuity in crystalline basement of the basin. The Krzyzowicki fault is located in the western part of the USCB where fold tectonic style dominates. Vitrinite, one of the basic components of hard coal is generally considered as optically anisotropic material. Anisotropy of physical properties is induced mainly by stress, which arranges vitrinite structure. Vitrinite anisotropy can be described by an ellipsoidal model called reflectance indicating surface (RIS) which is a geometrical representation of the optical anisotropy tensor. The investigation of the RIS for vitrinite was carried out on coal samples. The apparent maximum and minimum reflectance values measured for a single vitrinite particle were plotted against corresponding bireflectance to construct the reflectance crossplot. Interpretation of this plot yielded the magnitudes of the RIS three principal axes. The data obtained point to differences in optical anisotropy of coal under the study. The coal samples taken from block tectonic zone near the Klodnicki fault had mean reflectance value of less than 0.80 per cent. Their anisotropy coefficients were about 0.1. Optical properties of coal changed from the biaxial positive in the western segment of the fault to the biaxial negative in its eastern part. It suggests that past tectonic stress was greater in the western part of the zone than in the eastern one. Coal originated from a fold tectonic zone at the vicinity of the Krzyzowicki fault has mean reflectance value much greater than from previous region (ÿ1.20 per cent). Its optical anisotropy coefficient is equal to about 0.07. It suggests that paleostress field was more isotropic. The presented study shows the usefulness of coal reflectance measurements in the analysis of paleostress field existing during coalification process.

Jan 1, 2003

Since 1958 there have been 16 major coal mine explosions in the U.S. claiming 323 lives. Whilst the exact cause of a number of these incidents has not been determined, the majority has involved gas ignitions in one way or another. In addition there have been fatal gas explosions in salt mines and vapor explosions in oil mines. Furthermore, many of the oil shale mines in the U.S. have proven to be gassy giving cause for concern. Compounding these problems is the fact that frictional ignition of methane in coal mines has dramatically increased over the past several years; over 100 such ignitions were reported in 1979. While, no fatalities have been attributed to frictional ignition in the U.S. since early 1978, a recent mine explosion in Nova Scotia which resulted in 11 fatalities was attributed to a frictional face ignition. Research being conducted at the Bureau of Mines is aimed at the prevention and suppression of gas explosions. Emphasis is placed on new coal cutter bits for reducing ignition frequency, machine-mounted water sprays for preventing frictional face ignitions and automatic devices for quenching incipient ignitions and fully developed gas explosions.

Jan 1, 1981

By H Beucher

The uranium grade in roll front deposits is the result of successive processes that can be summarised in two steps. First a sedimentary phase, which gives the deposit support, then an oxidation-reduction phenomenon, which leads to the uranium deposit itself. In order to simulate such a deposit, it is important to mimic these different phases. The final aim of such a study is to localise the uranium itself and to reproduce the internal heterogeneity of the orebody in order to simulate the recovery process. The idea in this paper is not to reproduce a genetic approach but to consider the final image of the deposit. Three approaches are proposed. The first one consists of simulating the facies of the sedimentary deposit. The second approach reproduces the distribution of facies resulting from oxidation phenomenon (reduced or oxidised facies). The third approach consists of simulating the mineralisation at the interface of reduced and oxidised areas using the definition of a new data set determined by the grade values. At the end of each approach, the uranium grade could be simulated facies by facies according to the corresponding distribution characteristics. The plurigaussian method dedicated to random set simulations is well-suited for the facies simulations of deposits resulting from several sedimentary processes whether correlated or not. In this paper, the benefit of this method is demonstrated in an actual case study.

Jan 1, 2006

There is a well-known saying, variously attributed to the great King Solomon and other sages of antiquity, to the effect that 'there is nothing new under the sun'. The inventive genius of man, as far as it is personified in the metallurgist, has often had the truth of this statement poignantly brought to mind when investigating the priority of ideas in its own particular branch of science. Not infrequently some operation, at first inilocently taken for a novel procedure, has later been found to have had an irrefutable precedent in the more or less remote past.When confronted by a question of this kind the metallurgist can generally much simplify his search if he at once turns his scrutinising gaze towards that ancient home of metallurgy, Germany. Vast departments of the smelting art have originated there, and even when Germany has not been in position to claim priority of invention, it has at least been characterised by a distinction equally as worthy - ie that of the faithful and authoritative exposition of the theoretical grounds on which the invention rests.In the present instance, in endeavouring to trace the history of pyritic smelting, the writer has naturally turned in the abovementioned direction, and not without some result, although the recorded data are, as might have been expected, meagre. A complete history of the art of beneflciating ores by means of fire, in all its many ramifications, still remains to be written. Possibly it may never be written, for the extent of the subject is tremendous. It is even practically impossible to clearly trace the development of one of its most modest sub-branches in satisfactory detail, or to present that branch without going to a considerable extent into related matters of a merely general character. For the purpose of dealing with the subject it will be convenient to divide it into two concurrent heads, and to distinguish, for historical reasons as well as for metallurgical ones, between that branch of the general method of matte smelting, which, until about 1891, has been called 'pyritic smelting', and the more recent offshoot of the latter, which, by distinction, may be called 'pyrite smelting'. The nature of pyritic smelting was clearly defmed by Dr John Percy in 1880, and his interpretation3 may be accepted as well known. To recall the characteristics of the method we may perhaps paraphrase Dr Percy's meaning by describing the process as a special method for the smelting of lean or dry silver or gold ores, which do not contain sufficient lead or copper for these metals to act conveniently as collectors of the precious metals. The operation is conducted in a blast furnace, with an amount of carbonaceous fuel sufficing to produce an exclusively reducing atmosphere, and with the addition of pyrites, in order to form a regulus in which the precious metals shall be concentrated, the pyrites themselves being either argentiferous, auriferous, or cupriferous, or any combination of these three, or wholly barren of metal values. In the common acceptation of the term, it is understood that the use of the reverberatory furnace is excluded.

Jan 1, 1994

In North-West Nelson the Riwaka Complex, a linear basic intrusive complex, is exposed for approximately 45 kilometres. Some 500 kilometres south, across the Alpine Fault, a linear zone of similar but less well known basic intrusives that may be correlatives of the Riwaka Complex is exposed discontinuously for about 80 kilometres. The Complex was emplaced at several centers along a major tensional fracture zone that developed in upper Carboniferous to Lower Permian time. This fracture zone probably formed in response to the development of a west dipping subduction zone that gave rise to the Permian volcanic arcs in east Nelson and western Southland. The Riwaka Complex contains three rock suites. The Fractionation Suite, characterized by cyclic mineral layering and small scale cumulus banding is the largest and is divided into the Ultramafic, Hornblende and Plagioclase Series, each of which is subdivided into several units. The Cumulus Gabbros represent a restricted but important suite of unusual composition, while the third suite is the late phase Diorite Suite.

Jan 1, 1980

The first 12 m diameter rakeless thickener in the Australian gold mining industry was installed to treat plant tailings at the St Ives gold plant in April 2000. The plant processes approximately 3.2 M tonnes of ore producing about 430 000 oz of gold per annum using conventional crushing, grinding, gravity and carbon in pulp processing methods.The main benefit sought from the thickener was to improve water recovery in the plant and provide water for a 55 000 oz per annum heap leach operation. The thickener design indicated that more than 128 m3/h of overflow water could be returned directly into the plantÆs water circuit, relieving the demand on the borefields. The resultant surplus in the water circuit would then be available for the heap leach project. Based on laboratory and pilot plant scale tests conducted by EIMCO the thickener was designed to handle up to 700 m3/h of tailings slurry (450 tph of solids) with a 40 per cent oxide component in the ore blend. The normal plant throughput is 565 m3/h of slurry (400 tph of solids). Gold mineralisation in most areas at St Ives comprises quartz-sulphide vein and breccia lodes with common albite-biotite-chlorite alteration assemblages. There are well developed supergene gold horizons in the clay-oxide profile above most of the deposits (Osborne, 2002). This results in a wide variety of ore types being treated. At times 40 - 50 per cent of the ore may be oxide in nature. After some commissioning difficulties associated with instrumentation, the thickener has performed satisfactorily although it has not reached its design capacity. The maximum density achieved under normal operating conditions with 20 per cent oxide ore is about two per cent below the design. The thickenerÆs performance deteriorates further with increasing amounts of oxide ore in the blend. The thickener has provided sufficient water for the successful operation of the heap leach and has also provided some down stream benefits for the gold plant by way of pH and cyanide conditioned thickener overflow water.

Jan 1, 2002

The traditional form of project financing for resource related projects has involved project financings structured with either recourse to the project sponsor(s) or commercial banks accepting the project's risks, usually after project completion, subject to, inter alia, the nature of the project, geographical location, quality of the projected cash flows and commodity price outlook. However, the concept of commodity-linked borrowings hasadded a new dimension for borrowing opportunities for resource-oriented projects and or companies.

Jan 1, 1985

The Hunter Fracture Zone can be traced into the Fiji group, and onshore SE Viti Levu in the form of NE-trending morphostructures. NW- trending morphostructures offset the NE elements. Structural mapping of Suva Harbour indicates that the NE elements are grabens bordered by faulted monoclines. Faulting is characterised by block-rotations and dip-slip displacements. The NW morphostructures are faults displaying elements of both dip-slip and strike-slip movement. Structural overprinting suggests that the NW faults represent the youngest phase of deformation, and current seismic activity occurs on this trend. A conceptual, geomechanical model of the deformation invokes toppling and wedge failure at the edge of the Fiji platform, translating material downslope into the Hunter Fracture Zone. The interference pattern produced by the superposition of the NW on the NE structures consists of a series of circular features bearing superficial resemblance to volcanic centres. Known mineral deposits in SE Viti Levu correspond closely to these features. The formation of the circular features postdates mineral genesis, suggesting that the features provide a focus for the enhanced exposure of mineral deposits rather than a source of mineralisation. There is a close association between mineralised exposures and interference patterns in extensional structures in SE Viti Levu, and a correlation between these structures onshore, and the Hunter Fracture Zone cum South New Hebrides Trench offshore. Future mineral exploration in the SW Pacific will benefit by closer consideration of the geologic structure of Pacific islands bordering the extensional regimes of deep oceanic trenches.

Jan 1, 1987

By P Murthy, Z Guan, P Townson

In this paper, we introduce a methodology to optimise mining equipment operation in terms of the conflicting concerns of productivity and availability. We also introduce the concept of damage points and equipment dutymeters. These provide the mine management with tools to monitor the success of such optimisation. Since we have quoted the results of an on-going Australian Coal Association Research Program (ACARP) project, the apparent focus of this article is on draglines. However, the concept is equally applicable to other equipment. Mining is the type of business that requires a large investment in capital infrastructure and equipment to produce a product that is sold at a relatively low unit cost. In such a business, the key to competitiveness lies in achieving the full realisation of capital investment ie sustained production at high levels. Some of the concepts outlined in this paper are essential components of this picture.

Jan 1, 2000

By P Sutton

The global goal of Sustainable Development is not achievable without major changes in the way goods and services are delivered and material needs are satisfied, which requires tremendous innovation in the supply chains and life cycles in which minerals and energy processing take part. Values derived from minerals and metals processing need to be delivered with a fraction of current ecological impacts, which means removing technical obstacles to eliminating waste and emissions in the minerals cycle. The challenge is to find economically attractive ways to get there, through eco-efficiency gains in existing operations, capturing regional synergies, streamlining and greening the materials supply chain, and commercialising new process technology and new products. This paper summarises the outcomes of the Sustainable Resource Processing project, which was designed to provide a strategic analysis of what sustainability means for minerals and metals processing and how that can be effectively translated into technical and business innovation.

Jan 1, 2002

Agglomeration pre-treatment is a new process now being used here and overseas whereby problems arising with the heap leaching of gold and silver from materials containing critical amounts of fines or clay can be simply and cheaply overcome. The technique involves mixing the material with a suitable binder, commonly Portland Cement, and tumbling the moistened material to agglomerate the fines. These agglomerates are placed on the leach pad and cured prior to leaching. Test results, plant and operating cost data are presented. INTRODUCTION Heap leaching is a low capital and operating cost alternative to conven tional processing techniques for gold and silver extraction. A number of commercial-scale operations have recently started in the United States and the method is being considered for further deposits there and elsewhere.

Jan 1, 1982

By Denby B, Miles N. J

The underlying theory behind the construction of an on-line size analysis system is described together with an introduction to the Artificial Intelligent techniques that it is founded on. Previous systems based on more traditional technology such as edge detection and dilation algorithms have been restricted by the significant processing power they require, this has resulted in the production of systems with either reduced functionality or severe hardware requirements. A neural network approach offered a new perspective to the problem of size analysis; the ability of a network to learn and recognise subtle patterns in training data before on-line processing is initiated opened up the possibility for the production of a fully functioning practical system. The format of the training data had to be carefully analysed prior to its implementation in a neural network as the capability of a neural network solution depends as much upon a suitable data preparation as it does on the system architecture. To facilitate experimentation with various profile quantification techniques such as fourier and fractal analysis an Image Profile Analysis System was constructed (IPAS) in software on a personal computer. The IPAS system was produced with the aim of pre-processing image data to create data sets for experimenting with external neural network packages. The system allows the analysis of both real images obtained by image capture and simulated images created by an in-built in simulator. A measurement comparison scheme is also included together with a case study concerned with the frequency analysis of simulated images. The power of neural networks combined with the data compression provided by profiling removes the need for direct measurement of individual particles. This has obvious implications on the level of hardware necessary, and ultimately the expense of a stand alone system. The extrusive nature of data collection via an image analysis system will also permit simple installation of a shipped system; eliminating any requirement for interference with existing machinery.

Jan 1, 1995

The problems associated with achieving adequate accuracy for on-site axial flow fan performance measurements are discussed. The ability to test accurately rests heavily on equipment and installation design detail.Aerodynamic performance trials frequently cannot be carried out due mainly to the poor standard of installation design. In a majority of cases this results in unsteady, non-uniform inlet flow conditions to the fan. Details of installation design features and instrumentation, necessary for successful testing, are given for different types of installations and methods of testing. These cover both conventional practice, and new innovations which can provide solutions to difficult problems. Quantitative aspects of flow measurement are considered for various fan and duct configurations.Although the main emphasis is on large primary mine ventilation units which require on-site testing, the principles outlined have wide application to many other types of fan installation.

Jan 1, 1973

The Charters Towers 1:250 000 Gravity Data Set represents a new initiative of the Department of Resource Industries (DRI, formerly Queensland Department of Mines) to provide high quality regional gravity data over areas of the State that have high potential for new mineral discoveries. The Department has adopted a strategy to upgrade geophysical data to complement the ongoing Regional Geological Mapping Program (RGMP) of this Department and in areas where the data would be of most benefit to the mineral exploration industry. Part of this strategy is to ensure that these data are released within 6 months of data collection.The 1989 Charters Towers survey was completed as a joint project with the Bureau of Mineral Resources, Geology and Geophysics (BMR), and is the first regional geophysical data acquisition project undertaken by the DRI. Prior to this survey, the only gravity data in this area dates from the B MR regional surveys carried out between 1960 and 1967.

Jan 1, 1990

By J Bartlett, P Quigley

Historical research has played a significant role in the rebirth of the Bendigo Goldfield. The historical research undertaken by the company has been directed to specific areas such as verifying the total gold production of the field, the gold production from defined blocks on each of the major anticlines, the extent of workings of each mine which exceeded 200 m depth, the size and style of reefs mined in each shaft and also within specific domains of the field. Application of this data has assisted in the determination of possible dimensions of different reef styles and the location of mineralisation within each reef system. Description of grade variation, percentage of quartz and the amount and species of accessory sulphide minerals, as well as early geotechnical observations accompanying stoping methodologies, provides valuable analogues for reef structure being defined in the current program. Historical information on shafts on the two anticlines the company is exploring has allowed the postulation and recognition of repetition of reef development within the same stratigraphy in the hinge zones of the adjacent folds. The similarities of mineralisation styles across the field within both specific lithological units and structural setting has had important implications in respect to exploration drill targeting and the estimation of grade and tonnes.

Jan 1, 2003

By Lumley G. I, Hayes H

Non-intrusive methods for the reliable determination of dragline bucket and rigging performance have been achieved using physical modelling. Modelling offers a logical first step towards developing mathematical simulation models. The process of physical modelling has been applied successfully to predict dragline bucket performance and capacity as well as to demonstrate the effect of varying dump rope length on performance. ACIRL's Surface Miming Group has used physical modelling to carry out dragline bucket sizing for a new high productivity bucket and compared performance with Throng Coal's existing dragline bucket. The predicted bucket performance has since been confirmed in the field using dragline monitoring techniques.

Jan 1, 1992

It is a great privilege to be invited to give this address at this centenary conference. A centenary is a time for recollection, for celebration and for looking ahead. The AusIMM has much to celebrate and many things to recall. I hope in this address to make some useful comments about Australia's future (and mindful of but not forgetting New Zealand), looking ahead for 25 years or so, and the mining industry's role in that future.

Jan 1, 1993