Search Documents

By R H. Eric

Surface wave formation induced by a high-strength submerged jet in a bottom blown metallurgical vessels has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations. Experimental results have been discussed in terms of the wave period, wave frequency and wave amplitude with respect to air injection rate and tuyere configuration at a 0.23 m bath height. The results from high speed photography observations displayed the formation of rotating surface waves which circulates within the water model. It was found that the frequency and the amplitude increased with gas injection rate. The wave period for off-centre nozzle orientation was found to be lower than those of the centre configuration. The experimental results also showed that the frequency of a rotating wave increases when the tuyere orientation becomes off-centred . The predicted amplitudes were in very good agreement with the experimental values over a range of gas flowrates between 0.00599m 3/s to 0.01081 m 3/s.

Jan 1, 2000

By Massy-Greene RB

Limited recourse financing techniques reduce the financial exposure of equity holders to major mining projects by transfering some of the risks to the banks which provide loan funds for project development. This can only be achieved by a clear understanding of the principles involved. Engineering and management decisions on how the resource is to be developed and extracted must be made in the light of lender's requirements. The structure of sales contracts, joint venture agreements and many other documents can be important in limited recourse financing. If projections show that the debt can be repaid from project cash flow, loan agreements and other arrangements can restrict lenders ability to look to the equity holders for repayment of project loans.

Jan 1, 1981

Key blocks occur on the surface of excavations and on the walls of the ornamental stones and limestone quarries due to the formation of joint planes, fissures, microfaults and quarrying operations. Movements of these key blocks have produced numerous important failures and are responsible for routine overbreak and rock falls accounting for great costs. The thrust of this work is to demonstrate how to delimit zones of poten- tial key blocks (danger zones) in the wall of Bani-Khalid quarry of lime- stone by using the block theory technique (stereographic projection). The final result of this study indicated that, there are three potential key blocks, the most critical one has been determined. To treat the problem, we sug- gest either to provide timely support to prevent the movement of this block, or to analyze it further in hopes that available friction on the faces will hold it safely in place.

Jan 1, 1989

By Fuerstenau MC

Zinc cementation and carbon adsorption are both presently used for precious metals recovery from cyanide leach solutions. Each of these techniques exhibits unique processing features which renders them suitable to treat solutions with different properties and in different applications. In this study, the two processes are reviewed and compared. Operating data from a number of Merrill-Crowe precipitation and carbon adsorption plants in North America have been obtained and used in this analysis. The relative capital and operating costs for the two processes have also been considered.

Jan 1, 1993

By Sullivan TD, Redman PG

AND INTRODUCTION The Lochiel coal deposit, a large Tertiary soft brown coal deposit in the mid north of South Australia, is currently being investigated by the Electricity Trust of South Australia (ETSA) as a potential source of fuel for a base load power station. Feasibility studies indicated that the proposed dragline method of overburden removal was viable but economically sensitive to both highwail and dump batter angles. The unusual properties of the unconsolidated overburden sediments and the groundwater regime posed a number of intimately related hydrogeological and geotechnical questions which were addressed before and during the excavation of a trial pit. All strata at Lochiel are of soil strength, and artesian aquifers occur above and below the coal. From the initial evaluation of the deposit a number of hydrogeological questions were defined. These related to the rate at which the pore pressure in the silts is reduced by dewatering, the extent of the reduction in pore pressure due to prestripping, and the feasibility of dewatering and depressurising carbonaceous silty sand sequences. The site of the trial pit was selected to answer these and other questions from the basis of a detailed geological, hydrogeological and geotechnical understanding. The trial pit dewatering system simulated a full scale mine dewatering system and included ten pumped wells, twenty drainage wells, and nearly 400 monitoring instruments. It operated from September 1986 to June 1987. The excavation was carried out between February and May 1987.

Jan 1, 1988

By N Harries

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The æslope stability radarÆ (SSR) has been developed to better manage those risks. The SSR can remotely scan a rock slope to continuously measure any movement of the face. The system can detect and alert users of wall movements with submillimetre precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many mines in Australia, Indonesia, Africa, Chile and the United States. Greater than 100 rock falls and waste dump failures (from several tonnes to millions of tonnes) have been monitored, and on every occasion precursor æwarningÆ movements were recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper presents recent case studies of how the SSR technology has provided safety and productivity benefits to large open cut metalliferous mines.

Jan 1, 2007

Increasing attention is being focussed worldwide on the strategic environmental assessment of mining projects, including consideration of cumulative environmental effects. In New Zealand there is now an end in sight for inappropriate delays in resource consent approval of responsible mining projects. This paper investigates six case examples of recently consented mining and quarrying projects, whose applications were notified. It also explores the nature of delays that occurred, the factors that contributed to the delays, and whether the consent process delivered fair and effective public participation and desirable environmental outcomes.

Jan 1, 2005

By M Noy, P Hawkes

Improvements in the drill and blast process can impact on loader performance in a number of ways. The main effects being improved loading cycle times, less non-productive cycles such as oversize removal, clean-up and face raking and better bucket fill factors. The impact of improved loading cycle times on the overall cost and productivity of the load and haul cycle is very much dependent on the loader truck match and the management of the haul fleet. Previous work has shown that a 20 per cent improvement in dig cycle times may only lead to three per cent or less improvement in the overall productivity of the load and haul process. However, improving the mass loaded per pass by five per cent will lead to a five per cent improvement in productivity for any given haul fleet situation, assuming sufficient truck capacity. Work by Orica Explosives at Lab ChrysotileÆs Thetford Mine, Quebec, Canada showed a relationship between muckpile fragmentation and truck payload. With this in mind, work was carried out to determine the effect differing muckpile fragmentation distributions can have on excavator bucket fill factors. This work was performed in the laboratory to a 1:100 scale. Nine different distributions were used. These were characterised by the Rosin Rammler parameters, xc the characteristic size, and n, the uniformity index. The values of xc and n used were modelled on those previously measured at a Sydney quarry. For the range of distributions measured, it was found that the fill factors were lowest at a low characteristic size and a high uniformity index and highest at a high characteristic size and a low uniformity index. In other words the best fill factors were achieved with a more dispersed muckpile distribution with a larger characteristic size. The difference in fill factors was 16 per cent indicating that controlling the drill and blast process to produce a specific muckpile distribution can have a significant impact on the overall cost-efficiency and productivity of the load and haul process. Field measurement by Orica Explosives at a quarry in Canada supports this conclusion showing improvements of up to seven per cent in average bucket load by either increasing the characteristic size or decreasing the uniformity index of the muckpile.

Jan 1, 1999

By T Sirinawin, R H. Murfitt, W Shywolup

The Bong Mieu Project lies within the Pre-Palaeozoic Kontum Craton near the southern margin of the regional Phuoc Son û Tam Ky Suture. The Suture and accompanying Truongson Fold Belt of Indosinian age host significant gold and base-metal bearing districts including OlympusÆ other project at Phuoc Son to the west of Bong Mieu and OxianaÆs Sepon project in Laos. The Bong Mieu Project is located some 90 km south of Da Nang and some 30 km south-west of Tam Ky, the provincial capital of Quang Nam province in central Vietnam. The project area is covered by an Investment Licence of some 30 km2 which was granted in 1991 and a mining permit of some 365 ha granted in 1992. Several mesothermal, gold-silver deposits with assigned resources are present on the property. Deposits with assigned resources contain some 615 000 ounces of gold in situ. These are at Ho Gan and Ho Ray which are potentially exploitable by open-pit mining and Nui Kem which is potentially exploitable by underground mining. Newly discovered extensions to the known deposits at Ho Gan, Ho Ray and Nui Kem, and several other new prospects, are currently being investigated by drilling. The Ho Gan mineralisation is of mesothermal, shear and shear breccia quartz vein, as well as intrusive breccia hosted style. Nui Kem mineralisation is of mesothermal, shear and shear breccia quartz vein style. The Ho Ray mineralisation is of skarn (gold-bismuth-tungsten) and lesser quartz vein style. The deposits straddle and flank the east-west trending Bong Mieu Anticline which trends through the central portion of the Investment Licence. In this paper the geology of the deposits, details of resources, results of recent exploration on the Investment Licence and recent engineering and mining studies at Ho Gan are briefly reviewed.

Jan 1, 2004

By Cowie WJ, Utting BS

The alluvial gold industry of New Zealand is based on the placer deposits in Otago and on the West Coast. Production from these since discovery in the 1850's has been an estimated 480 tonnes (15 million ounces) of gold. Annual output has expanded continuously since 1980 and is expected to be over 2 tonne of gold for 1989.Following a historical review, the characteristics of typical operations, which use hydraulic excavators and mobile trommel units are discussed. Descriptions are then given of alluvial activities in Otago and on the West Coast.

Jan 1, 1990

By M Magee, D Way

The Mount Isa Copper Concentrator was commissioned in 1973. In 1991, two autogenous grinding mills were installed replacing two stages of crushing, one stage of rod milling and one stage of primary ball milling. The cyclone overflow P80 of the secondary ball milling circuit was reduced to 120 microns due to the increased operating power in the AG/SAG mill circuits. A study of the mineralogy of the milled products and the plant flotation recovery indicated that the installed secondary grinding energy was more than what was required for adequate liberation of the chalcopyrite and half of it had potential for more effective use elsewhere. Halving the secondary grinding energy meant only one of the two secondary ball mills would be needed. The predicted saving in operating cost of one less ball mill was more than two million dollars per annum. This paper summarises various plant trials that were conducted in the Copper Concentrator to decommission one of the two secondary ball mills.

Jan 1, 2004

By Sullivan T. D, Lohe E. M

Geological structure is one of the main controls on ground conditions within mining. It has a significant impact on the mining conditions and productivity of coal mines within the Sydney - Bowen Basin. The three main types of faults common to this region, normal, reverse and strike-slip systems, each present distinct challenges to mining. These systems effect a wide range of geotechnical and mining conditions within the mines. These include coal quality, strata stability, goat and caving behaviour, productivity and maintenance schedules of mining equipment, mine design and mine-site stress fields. A better understanding of the regional, local and mine-scale structural setting, timing relationships of structural events and the mechanisms of fault formation will greatly aid industry's push for greater productivity and competitiveness.

Jan 1, 1991

By Fuller P. G

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these Situations.

Jan 1, 1992

By Harbort G. J

Jameson cell pilot plant trials were conducted in a number of areas in the Red Dome gold/copper flotation plant during 1991. The aim of testwork was to reduce the amount of cyanide soluble copper reporting in tailing to the gold leach plant, and hence reduce cyanide consumption. A number of these tests were conducted in parallel with conventional flotation columns. Laboratory tests were conducted to simulate the performance of the existing plant when compared with the addition of the Jameson cell allowing an extra sulphidising phase. This paper reviews the comparison of the Jameson cell and conventional columns in recovering cyanide soluble copper, while maximising copper concentrate grade. Key parameters that are investigated are residence times, air/pulp ratios, superficial gas recoveries and size by size recoveries. A brief comparison of performance of the Jameson cell and column in the controlled potential sulphidisation process is also presented. An estimation of the reduction in cyanide consumption is given.

Jan 1, 1992

Cleaner Production stands for a proactive and preventive approach to industrial environmental management and aims for process- and/or product-integrated solutions that are both ecologically and economically efficient (æeco-efficiencyÆ). Pioneers in the field were large manufacturing and processing industries in the USA (since the late-1970s), but it took until the early-1990s before Cleaner Production was generally recognised as a valuable approach for large and medium sized enterprises. The application of Cleaner Production in mining and minerals, metals and energy production appears to lag behind other sectors, such as manufacturing and processing. This paper starts with a discussion of the Cleaner Production concept and provides examples of its application from a few selected Australian mining and minerals processing industries. This evidences that Cleaner Production can achieve significant reductions in environmental impact, in terms of reduced waste and emission generation and in terms of conservation of materials, energy and water, while simultaneously reducing operating costs. The paper then investigates a number of key issues pertaining to the implementation of Cleaner Production; ie organisation and management of Cleaner Production activities, effective tools for mastering the Cleaner Production concept as a way of life, and performance measurement.

Jan 1, 2002

By R Grogan

The Ungay-Malabago polymetallic deposit, currently owned by Lafayette Mining, is located on the eastern end of the island of Rapu-Rapu which lies east of the city of Legazpi in the Philippines. The island is sparsely populated and has largely been deforested by extensive logging some 30-40 years ago.The deposit is situated on a plateau some 200 m asl and lies about one kilometre inland from the coast. The site topography is difficult with minimal flat areas for plant facilities. The region around Legazpi is subject to volcanic activity and though the island is not affected it is in a seismic zone. There is no other mining or other industrial activity on the island, the local inhabitants being engaged in subsistence farming and fishing. These activities place a high level of responsibility on the mine operator with regard to the environment and the provision of employment and training to the local inhabitants. Although no previous mining was carried out at Ungay, shallow pit mining for high-grade direct smeltable copper ore has occurred during the mid-1900s in an area, known as Hixbar, some 2 km west of the deposit This area is currently being explored by Lafayette.

Jan 1, 2002

Warrego copper ore characteristically contains 0.05-0.2% bismuth, which on upgrading produces a concentrate of approximately 1.3% bismuth. Early smelting of this concentrate (1973) was accomplished in a flash furnace (eliminating 92% of the bismuth in the con- centrate) and Top Blown Rotary Convertors (eliminating 85% of the bismuth in the matte). However 1.3% bismuth was considered the max- imLun bismuth level that could be treated. Geological evidence indicated that the bismuth level in~the copper ore would increase and that the bismuth level in the Warrego ore would be 0.3-0.7% bismuth. Treating these ores would produce a copper concentrate with bismuth levels far in excess of those accept- able to the smelter and still produce low bismuth content blister (limit 0.03% bismuth).

Jan 1, 1984

Where vertical or near vertical faces are required in open excavations in soils and rocks, some form of stabilization of the 'cut is often necessary. Stressed anchors either alone or in combination with steel, timber or concrete-lagging are often an economical and versatile means of providing support. Stressed anchors are also-a very economical means of anchoring a wide range of structures such as dams, cranes, transmission towers, retaining walls, spillway aprons, bridge piers; and - stacks. The anchors need not be stressed always on installation.other than to proof load them. A number of examples illustrate some of-the more practical aspects of.the design and construction techniques used. No new methods of design or construction are involved, but merely some consolidation of the engineering design, soil and rock mechanics,thinking applied to the stressed anchor tech- nique.

Jan 1, 1971

Mining is taking place at increasing depths of cover on the Southern Coalfield beneath pre- dominantly massive sandstone strata. Within the next twenty years, there will be longwall mining at depths greater than 600 m. As the Sydney Metropolitan area continues to expand and as coal mining approaches these urban areas subsidence will continue to become an increas- ingly important aspect of coal mining research. Investigations commenced in the mid 1960's and it is now possible to predict subsidence in the Southern Coalfield with reasonable con- fidence. The work is showing that the characteristics of the subsidence troughs over the deeper mining at Appin differ from the characteristics of mine subsidence at less cover. The longwall mining at Appin Colliery has resulted in a maximum measured subsidence of 730 mm. The maximum strains were small because of the large radii of curvature of the subsidence profiles. There was no damage to any of the buildings in the township of Appin.

Jan 1, 1981

THIS instrument, depends on the principle that, over a short period, the surfaee of a porous substance from which a liquid is evaporating receives the same amount of heat by conduction, convection, and radiation as it loses in the latent heat of the evaporating liquid. If, then, the amount of heat being received by a surface can be measured, the rate of evaporation can also be obtained. The Kata thermometer is also based on this principle differently applied.The instrument, as shown in Fig. 1, consists essentially of a thermometer with a sliding which is divided by three pointers into two equal parts which may be spaced so as to cover a distance of, for example, 5° of the thermometer scale. The instrument is calibrated so that the amount of heat required per unit area of the bulb to raise the menissus is known. The method of using the instrument is as follows:The slide is first set so that thc central pointer is at the temperature of the evaporating surface.The thermometer is cooled by any convenient means so that the meniscus is several below the lowest pointer. The thermometer is then placed near the evaporating surface, when the Ineniscus begins to rise and the time taken for it to rise from the lowest to the top pointer is measured. From this and the calibration results the amount of heat retained per unit area of the bulb at the mean temperature...

Jan 1, 1928