Search Documents

By Williams DJ

Preliminary calculations suggest that spoil piles in the Bowen Basin will undergo approximately 4 m settlement as the ground water table recovers after mining is abandoned. Approximately 1 m of differential settlement is possible. Superimposed on this will be a long term creep settlement of 1-3 m/log cycle of time. Depending on the nature of the spoil material, partially submerged spoil piles could be sufficiently stable although to ensure stability during long term creep it may be necessary to flatten the final spoil pile face to approximately 25¦.

Jan 1, 1987

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal.

Jan 1, 1989

By Anderson JDC

Opencast Lignite Mining requires topwall strata of seams to be fully depleted and footwall aquifers sufficiently depressurized. To prevent a spread of the cone of depression into protected wetlands some distance away, alternatives had been investigated such as closing water works, underground slurry wall barriers and recharge by infiltration. As a result of these investigations, the infiltration method has been chosen and in a first phase during the next decade it will utilize as much as 55 x 106 m3/year. Using this approach, the survival of the wet lands is assured.

Jan 1, 1988

The sharp deterioration in Au~tralia'S ternn of trade in recent years and the accumulating national debt highlight the need for a restructuring of the economy which is highly dependent upon primary agricultural and mineral commodity exports (figure 1). Table I gives an indication of the value that can be added to raw material by mineral processing. Significantly higher value is added through downstream manufacturing. In 1987, the mining and rural sectors accounted for 47010 and 38010 respectively of total exports valued at $35,782 million (figure 2). The export contribution from minerals comprised $12,266 mil- lion from unprocessed ores and concentrates and $4,668 million from metals and processed minerals including some simple manufactures. Coal accounted for 450/s of total primary mineral exports. Iron ore and alumina are other important mineral exports, while gold and aluminium are major metal exports. (Figure 3) Australia's minerals are now traded in a much more competi- tive and oversupplied market in contrast to the 1960's and 1970's period which was characterised by increasing exports of largely unprocessed ores and concentrates. Since the early 1980's (I cI) resscd )ver~cas nutrkcts and km rununodlity liriccs ha~c hcen the product of excess capacity installed to satisfy a forecast high growth in demand which never eventuated due to the world reces- sion. During this period the emphasis on technology development was focussed on reducing costs through increased production effi- ciencies in order to maintain competitiveness.

Jan 1, 1988

The paper describes a simulating method.for ground water contamination originating from industrial and mining activrty. The finite difference model simulates heat, mass and solute transport. The applied stochastical method for dispersion provides more accurate solution of mass transport modelling. This method gives a more realistic approach of chemical processes in an aquifer depending on temperature.

Jan 1, 1988

By S Miller, A Neale

As part of a long-term acid rock drainage (ARD) mitigation study, PT Freeport Indonesia has completed the construction of a highly instrumented, full-scale, experimental, overburden stockpile to further evaluate the behaviour of the waste rock system at Grasberg mine. A total of 24 lysimeters, 30 sets of thermistor strings and 48 oxygen-sampling ports were installed at select locations during stockpile construction. ARD flow rates and chemistry have been recorded since the start of overburden rock placement in April 2000. Measurements of in situ temperatures and oxygen concentrations quantify reaction rates and the oxygen pathways that control oxidation kinetics deep within the waste rock profile. Direct field observations show the significance of advective oxygen flow with respect to the onset of oxidation kinetics. Oxygen measurements show that the rubble zone that forms at the base of a waste rock bench provides a critical pathway for oxygen entry to the waste rock profile. Furthermore, rapid oxidation as evidenced by measured temperature increases deep within the panels of waste rock is observed to occur. The observations presented in this paper provide critical insight for understanding the mechanisms and behaviour of full-scale waste rock stockpiles with respect to ARD generation. The results of this program will assist in the future selection, testing and evaluation of appropriate mitigation measures with respect to surface and face treatments to reduce long-term ARD generation. This project is a work in progress, and at least another two-years will be required to fully understand site-specific ARD generation and ARD mitigation mechanisms. This paper will discuss various design and construction considerations, provide an overview of results achieved to date, and some preliminary interpretation of what is happening within the overburden stockpiles.

Jan 1, 2003

By Smitham J. B, Keast-Jones R

Six Australian coals were selected to determine their potential to produce, ultra low ash (less than 2 per cent) coal by progressive size reduction followed by density separation and/or froth flotation. Density separation in organic liquids is effective in the absence of contaminating liberated mineral matter which can be removed by froth flotation with several cleaning stages. The limit of cleaning of these coals was an ash value of 1 per cent while commercially attractive yields were obtained at 2 - 3 per cent ash depending on the coal.

Jan 1, 1987

Over the last thirty years production of heavy minerals from Australian deposits has dominated the world market. The main incentive has been to suoply the raw material for titanium dioxide based pigments. These ~ninerals include ilmenite, rutile, leticoxene and more recently, synthetic rutile. Inevitably the viabilit/ of developing placer type deposits has seen influenced by other heavy minerals present, such as zircon and monazite, but these have been of secondary importance. For most of the sixties and seventies, Australia supplied the 'najority of free world rutile and zircon, and a large proportion of the ilmenite. With the run-down of rutile- rich reserves in eastern Australia, the emphasis has s:iifted in several countries, including Australia, to fill }the gap with i l Wen i to and its derivatives, leucoxene, synthetic rutile and titanium rich slag. over the next 15 - 20 years, as high grade beach placers in Western Australia are mined out, less traditional sources for mineral sands products will be opened up. Low grade placers (particularly those dominated by ilmenite) will be reassessed in Australia, U.S.A., Africa and Asia, and exploration will shift from beach and dune environment, to heavy mineral concentrations in alluvials, lake deposits and continental shelf deposits. At the same time, production of anatase and bastnaesite will be expanded, as required, from the huge resources contained in carbonatites in 3razil, U.S.A. and China.

Jan 1, 1986

A minimum target of economic growth in Australia has been set at 5% per annum growth in G.N.P. at constant prices (Vernon Committee). 2. The core of the problem of sustaining steady growth at this or a similar rate is to ensure regular flows of investment. This sustains productivity, helps to control balance of payments pressures, and to check inflation. 3. The regular intake of human and physical resources, in conjunction with intensive capital development involving finance, technology and management, is basic to sustaining the growth rate and ensuring rising standards of living.

Jan 1, 1971

In 1976, The Zinc Corporation Limited Broken Hill set up a plant to re-process a hill of tailing (Mt. Keast) from the original treatment operations. With the likely disappearance of this source of feed in 1985, an investigation was initiated to determine what other feed sources might be available. This involved searching through old records and photographs as well as a subsequent drilling campaign. The paper briefly covers the history of treatment operations and describes, as a result of the information obtained, the likely future sources of feed.

Jan 1, 1983

By W A. Peppin, D N. Riley, N W. Schulenburg

In June 2008, a joint airborne collection using hyperpspectral systems was tested on a single Twin Otter aircraft. This experiment was designed to incorporate two airborne hyperspectral sensors for geological and environmental projects. Mineral exploration and environmental impact statements are two areas where full spectrum hyperspectral data can document the mineralogy at the surface prior to mining operations. Many previous hyperspectral remote sensing collections were collected on a single aircraft with a single sensor. Mineral mapping using hyperspectral sensors that measure in complimentary regions of the electromagnetic spectrum is cost effective as it allows for the mapping of clays, sulfates, carbonates, feldspars, quartz, garnets and many other minerals. This report describes the experiment using the following two hyperspectral sensors: ProspecTIR, a visible near and shortwave infrared (VNIR-SWIR) sensor with 356 channels and spectral range of 0.4 to 2.5 ¦m, along with a spatially enhanced broadband array spectrograph system (SEBASS), a midwave and longwave infrared (MWIR-LWIR) sensor with 128 channels from 2.5 to 5.3 ¦m and 128 channels from 7.6 to 13.5 ¦m. SpecTIRÆs ProspecTIR system and The Aerospace CorporationÆs Spatially Enhanced Broadband Array Spectrograph System (SEBASS) are pushbroom sensors, have high signal to noise ratios, have similar swath widths and instantaneous fields of view. Examples of data collection experiment will be shown with a focus on mineral/lithologic identification and mapping along with environmental assessment in the western United States. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Groudeva VI

The biohydrometallurgy of gold is based on different processes which could be grouped into four main groups (Attia, Litchfield and Vaaler, 1985; Karavaiko et al, 1988; Groudev, 1990): 1. bacterial oxidation of gold-bearing sulphide minerals by chemolithotrophic bacteria to facilitate the subsequent chemical extraction of gold; 2. solubilisation of gold from oxide ores by means of heterotrophic bacteria; 3. recovery of gold from solutions by biosorption; and 4. microbial modifications of the surface of gold-bearing sulphide minerals to improve the subsequent gold concentration by physical dressing methods (eg flotation, oil agglomeration).

Jan 1, 1993

By J Chßvez, J Rosa del Castillo, J Rui

Environmental Impact Assessment (EIA) and Feasibility Studies (FS) were carried out to evaluate the potential use of treated acid mine drainage (AMD) occurring at the Kingsmill Tunnel in the Central Andes of Peru. The 11 km long tunnel drains the underground works of the Morococha Mining District and discharges about 1.25 m3/sec of AMD directly into the Yauli River in the Amazon Basin. The communities living downstream cannot use the Yauli River water due to its low pH and elevated concentrations of metals (eg Cu, Zn, Fe, Mn, As, Cd) and sulfate. Studies carried out for this project included technical feasibility, EIA, economic viability and social impact assessment phases. During the æTechnical FeasibilityÆ phase, the treated AMD was produced by simulating a high density sludge (HDS) lime neutralisation/ precipitation process and was evaluated for various potential uses. Mining companies located in Morococha, in particular Centromin Peru SA, and the Water Works Company of the City of Lima (Sedapal) collaborated with Golder Associates during the studies. The Canadian International Development Agency (CIDA) provided the financial assistance. The results of the physical, chemical, biological and toxicological analyses demonstrated that the AMD could be sufficiently treated to be potentially used to supplement the drinking water supply of Lima, and for agricultural (eg irrigation and livestock) and recreational purposes. Process design and scale-up parameters were also determined for implementation of the full-scale treatment facility at the site. The use of the treated AMD as a drinking water supplement would be economically feasible.

Jan 1, 2003

The difficulty of successfully imple menting a landscape policy is almost incom- prehensible. Landscape design is recognised as an essential component in the integration of engineering and architectural projects into the landscape, but the factors which prevent the achievement of a successful result are rarely recognised or assessed. In many cases these prohibiting factors are due to a lack of understanding of the effect of major planning decisions on the existing landscape, the importance of the landscape plan and the significance of appro- priate specified techniques to prevent un- necessary damage and to ensure retention of existing vegetation in a healthy condition. The role of the landscape architect in incorporating new land uses into the landscape provides the background against which factors which inhibit policy achievement can be con- sidered.

Jan 1, 1976

The new generation Hlsmelt« Direct Iron Ore Smelting Process is a CRA Limited technology initiative. The process development is now focussed on commercialisation. The goal is to have the first commercial vessel operating around the year 2000. The HIsmelt« Process, based on the abundantly available iron ore fines and the more readily available non-coking coals, has the potential to fundamentally change iron ore processing through the application of high intensity techniques to replace the current sinter/coke ovens/blast furnace .technologies. The process will have great potential in the rapidly growing economies of Asia where steelmaking aspirations are based around local market focussed plants. This potential can be. realised as a supplier of premium grade iron units to electric arc furnace (EAF) steelmaking plants or as the front end to an ore based steel mill.

Jan 1, 1996

A laminar-flow furnace technique was used to study the combustion of 37-53 µm size fraction of Woodlawn copper concentrate containing 7.4 per cent zinc, 5.0 per cent lead and 22.5 per cent copper. Factors studied included the effect of time, temperature and the distribution of volatile elements between the panicles and the fume. Air was used for most of the work but a few tests were carried out using 1 per cent oxygen in nitrogen. Chemical analysis, X-ray diffraction, and scanning electron and optical microscopy of polished sections were used to characterize the reaction products.When the concentrate was combusted at low temperatures (800-900°C), the fume was rich in lead. At higher temperatures, this was diluled by increasing amounts of zinc and copper. 70 per cent of the zinc, 60 per cent of the lead and 40 per cent of the copper were found in the fume after oxidation at 1400°C. Lead, zinc and copper were present in the fume as anglesite (PbSO4), zincite (ZnO) and cuprite (Cu2O) respectively. The major phases present in the panicles were magnetite (Fe3O4) and/or cuprospinel (CuFe2O4), with some zincite and cuprite.Elemental copper was found in the particles oxidized in 1 per cent oxygen. Possible vapour species responsible for the vaporization are discussed.

Jan 1, 1985

By Yanagase T, Nakamura T, Ueda Y

The possibility of removing the phos phorus and sulphur contained in steelmaking slag has been studied by observing directly through the microscope melts heated on Pt- filaments. After a CaO crystal was placed in the molten slag, distributions of P, S and other elements formed around the CaO crystal were determined with the aid of EPMA. The results indicated that a layer of 2CaO SiO2 is formed on solid CaO in CaO-Si02 melts. Then between CaO and the newly formed compound the molten slag tends to migrate through cracks. For higher Fe 2 03 contents, the layers of the compounds 2CaO.Si02 and 3CaO SiO2 formed around the CaO crystal are not continuous but look more like particles, which promotes the dissolution of CaO. Phosphorus in slag was found to be enriched in the 2CaOòSi02 layer. Phosphorus in the 2CaO SiO2 phase is not related to the primary slag composition, being about 5-7% P205.. Sulphur in slag,as well as the phos- phorus,was concentrated in the 2CaO.Si02 phase. Disintegration due to weathering observed for slags produced in these investigations appeared to be due principally to hydration of lime.

Jan 1, 1980

THE power requirements of the Mount Lyell Mining and Railway Company at Queenstown, Tasmania, have, since the inception of smelting operations in June, 1,,896, been derived continuously from the extensive forests in the watershed of the Queen River, adjacent to -the works, the firewood being of good quality, mainly composed of myrtle or beech (Fagus Ounninghami), eucalypts, and manuka (Leptospermum ericoides).The country is very rugged and mountainous, indented by numerous ravines and gullies, and intersected by many creeks, which are subject to periodical floods, under the influence of a heavy and persistent rainfall. The areas so far exploited aggregate a total of about 42 sq. 'miles, and this denuded country gives promise of ultimately becoming very valuable pastoral ground for cattle-raising. The tonnage of wood yielded per acre varies from 40 to 100 tons on stack measurement of 80 cub. ft. per ton, 60 tons per acre being considered a good average yield. The gross amount of firewood handled during the past 13 years approximates 1,200,000 tons, the greater portion of which has been obtained by ordinary tramming methods. The company's main line of railway, 3-ft. 6-in. gauge, has served as a trunk line for all supplies derived from the Queen River valley, south of the reduction works, while the northern and western areas have been exploited by means of...

Jan 1, 1911

By L Wsrell

During recent years the iron ore industry has experienced a continuous consolidation trend following increased merger and acquisition activities. Analysing and evaluating these mergers is important in order to establish potential effects. The purpose of this paper is to analyse the price effects caused by the merger between Rio Tinto and North Ltd in 2000. The merger was cleared by the European Commission, as well as the Australian Competition and Consumer Commission, shortly after its announcement. The analysis will be conducted using a simulation model based on a proportionality calibrated almost ideal demand system, which uses the premerger situation in order to estimate the post-merger outcome. The relevant market is defined using shipments data. This is followed by the simulation model applied to the defined relevant market. The results show that the concentration on the market, given by the HHI, increases approximately 15 per cent, and that the market share of the new companyÆs reaches almost 20 per cent. Compared to the CommissionÆs assessment the results indicate a more concentrated market and thus a higher concern for possible competitive effects. Furthermore, the results suggest that the predicted average market price increase from the merger is 1.6 per cent. However, the merged firm is able to increase their average price by 5.1 per cent.

Jan 1, 2005

By R Valenta, J Owen, D Kemp, E Lebre, G Corder, J Thomas

Numerous recent analyses have shown that future demand for a broad range of critical commodities is unlikely to be met by new discoveries and recycling alone. The only practical alternative source to address this shortfall comes from orebodies which are currently either uneconomic or inaccessible. A common assumption is that a simple rise in commodity price will render these deposits economic. The mining industry has a long history of innovation allowing economic production from increasingly low grade and technically challenging orebodies. Industry “roadmaps” have been produced on a regular basis, with the aim of identifying future innovations which will allow this progression to continue. At the same time, there have been relatively few systematic analyses of the actual range of challenges facing undeveloped orebodies. The aim of this study is to analyse the mix of challenges faced by a group of undeveloped orebodies in order to better understand the relative importance and necessity of innovations applicable to the deposits, with the ultimate aim of determining the relative value and impact of possible innovations to the economic viability of those deposits. CITATION: Valenta, R, Lebre, E, Kemp, D, Owen, J, Corder, G and Thomas, J, 2018. Can a simple price-rise unlock complex copper orebodies?, in Proceedings Complex Orebodies Conference 2018, pp 71–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018