Search Documents

By I F. Wood

Planning for flooding and assessment of flood impacts are important requirements for mining projects, as they are also for other types of development. With more intense development and concern from the community, supported by government regulatory requirements, assessment of flood concerns and impacts has become of increasing importance. To ensure that flooding issues are fully understood and results presented in an appropriate format, advanced hydraulic analysis procedures have been developed and are beginning to be applied. These procedures must be rigorous in an engineering context but the results must also be readily understood by the community and government agencies. Advanced two-dimensional hydraulic modelling is becoming accepted as an important means of assessing flooding issues for mining projects. With presentation of results from hydraulic models with Geographic Information Systems (GIS), flood impacts can be analysed rigorously and presented clearly. This paper discusses the application of advanced hydraulic modelling in the planning and impact assessment of a major mining project located on a floodplain where there is extensive inundation. The analysis provides for both input to the planning of the project and for detailed assessment of potential impacts. This case study illustrates some important aspects of the application of hydraulic modelling using a two-dimensional modelling to a critical flood design.

Jan 1, 2003

By Warner RE

SINCE 1952, when Elliott et a/ first applied the Sherwood correlation for flooding in chemical absorption towers to blast furnaces numerous investigators throughout the world have followed their example and much research effort has been spent to tighten the correlation and recently to extend investigation of flooding to side gas entry conditions. The widespread use of the Sherwood concept of flooding has been such that even the word itself has become an integral part of blast furnace nomenclature. The evidence for the applicability of Sherwood's relationship has been that the flooding limits calculated from blast furnace parameters lie approximately on the Sherwood line. However, the values of many of the variables for the blast furnace calculation are only estimates and at first sight one may wonder at such 'close' coincidence when some of the estimated parameters entering the Sherwood correlation are raised to the power of three or more, as for the bed porosity and the liquid surface tension. It is felt that the explanation of this result lies in the logarithmic: nature of the plot and/or the fortuitous can- cellation of the errors of the estimates in the calculations coupled with the fact that blast furnace fluid ratios lie within a very narrow range of values. The foregoing considerations should in their own right place doubt on the correctness of the Sherwood type flooding correlation applied to the blast furnace. Additional doubt regarding the existence of the Sherwood type flooding in the furnace has been cast by the results obtained in the Tokyo University experimental blast furnace. From the reasoning of both Standish and Colquhoun (p. 20) and Warner (p. 23) it is deduced that flooding in the traditional sense will only normally occur in the upper bosh (somewhere near the mantle), following softening as discussed by Palella et a/ on p. 75, and flooding in that zone is likely to result in furnace irregularity. On the other hand, the concept developed by Warner of slag hold-up above the raceways as a stable phenomenon not affecting furnace regularity is a process unique to the blast furnace and is not described by the Sherwood flooding theory. Recognising the considerable practical implications of slag hold-up above the raceways, this note further explores the physical process of slag hold-up. We envisage that bed of coke above the raceways in almost all blast furnaces would contain some slag held up by the gas pressure gradient. In general the slag would be contained in a ring and gas would bubble through in its ascent through the furnace. The force supporting this slag is the pressure gradient and obviously -much of the blast pressure is dissipated in supporting this structure.

Jan 1, 1975

Reliable predictions of the long-term water quality and water level fluctuations in a final void are vital if mine operators propose to decommission final voids in open cut mining operations. The catchments feeding final voids typically comprise a large proportion of coal placed or re-shaped spoil piles. Spoil piles from open cut coal mining operations have distinctive hydrological characteristics, which result in unique run-off behaviour. There is a need to understand the nature of spoil hydrology processes in order to predict the long-term hydrological behaviour and water quality responses of such systems. Preliminary estimates indicate that it may take 20 or more years for a void to flood. It is impractical for mine owners and operators to wait until long-term hydrological and water quality conditions have been established in a void, before reaching agreement with regulators about mine closure conditions. Reliable simulation of the long-term water quality and water level fluctuations in a void are therefore. The adoption of an agreed modelling approach and sharing of results from field data programs could result in the establishment of a database that could be used, with regulatory approval, for assigning parameter values, without the need for a specific data collection program for every individual void. Industry and regulators should agree on the model adopted for predicting post-closure behaviour of spoil/void systems. This will require reliable, robust methods for field data collection. This paper describes the field monitoring, data collection, model preparation and simulations undertaken over a three year period for Australian Coal Association Research Projects (ACARP) Project C7007. It presents the findings of that research, and provides comment on aspects of the project that were undertaken well and on aspects that could have been done better. Limited data is presented in this paper due to confidentiality arrangements with the relevant mine sites.

Jan 1, 2003

By H Arvidson, D Guibal

This paper presents updated interpretations of controls on mineralisation in C Deposit and highlights structural features that influence the geometry of mineralisation domains used in resource estimation. The Area C mining lease is located in the central Hamersley Province, ~100 km WNW of Newman, Western Australia, and contains resources of approximately 1100 Mt of Marra Mamba and Brockman iron mineralisation. C Deposit is located within Area C, on the northern limb of the Weeli Wolli anticline, and mineralisation is hosted predominantly in the Mt Newman Member of the Marra Mamba Formation. Production from C Deposit began in August 2003, following mining of a 950 000 tonne bulk sample in 2002. Recent mapping in the bulk-sample pit and updated interpretations by BHP Billiton geologists have highlighted the significance of structural controls on mineralisation in C Deposit and their influence on the thickness of mineralisation, which ranges from 20 to 80 metres. Structural controls on the geometry and continuity of mineralised domains include south-dipping thrust faults that developed along the Mount Newman/West Angela contact, folds associated with thrust fault development, steeply dipping stratigraphic contacts in the hanging wall of the thrust faults, and gently north-dipping stratigraphic contacts. Thrust faults and folds in C Deposit are significant for two main reasons: their formation resulted in the thickening of the main ore-hosting units in the Mount Newman Member; and faults and folded stratigraphic contacts provided conduits for supergene metasomatic-enrichment processes that produce high-grade iron mineralisation.The implications of this interpretation for the definition of the resource estimation domains are discussed, and suggestions are made for a better integration of geology into the data acquisition and estimation process.

Jan 1, 2005

Minerals and Metals Group (MMG) Century mine (Century) is a large open-cut mine in northwest Queensland approximately 2.5 km long, 1.5 km wide and 240 m deep, with an ultimate pit depth of 320 m. In 2009, the mine experienced three failures which began as small failures, and progressively developed into significant multi-batter failures. The incidents were managed by a combination of analysis, redesign and practical management to achieve positive outcomes for the mine. On the south wall of the mine, a series of batter-scale wedge failures occurred in December 2007. Analysis of structure orientations and design changes aimed to minimise the risk of failure extending over multiple batters, while accepting a risk of further small-scale failures. Design changes were constrained by a culturally sensitive area (CSA) located south of the wall. As mining progressed, shallow wedge failures developed over multiple batters and cracks were observed 60m back from the pit crest, indicating that a large-scale wedge failure was developing. Movement increased in January 2009 as a result of significant rainfall. After considering several design options, the area was stabilised by a cut-back of the wall. Two multi-batter failures also occurred on the north wall as mining progressed through a structurally complex area. Both north wall failures began as small failures that progressively developed, and required a redesign of the wall below as well as practical management of safety aspects. The complex structural geology was difficult to predict ahead of mining, and required geotechnical input into design changes as mining progressed. All three failures potentially had significant impact for ore recovery, and were managed by a combination of analysis, redesign and operational management have resulted to achieve positive outcomes in a challenging mining environment.

May 1, 2010

By B Cronin, M Gao, M F. Young

Fine grinding technology has become extremely important for Mount Isa Mines Limited in the last decade for flowsheet development for the McArthur River deposit and in rejuvenating the Lead-Zinc Concentrator at Mount Isa. Regrinding products with 80 per cent passing seven microns and 12 microns were required, respectively, for the McArthur River ore and the Lead-Zinc Concentrator at Mount Isa. Development of the ISAMILL, a horizontal stirred mill with a gross mill volume of 4000 litres (a net volume of 3000 litres), has been successful in delivering the required grinding product sizes with an energy consumption acceptable to a mining operation. The ISAMILL performance for processing both lead and zinc streams at Mount Isa is discussed in this paper, including the milling energy efficiency, the media wear and the size-by-size recovery data for one flotation process following the fine regrinding stage. The potential use of the ISAMILL technology at various phases of the mining cycle is also discussed.

Jan 1, 1998

By A J. Clough

There has been an unprecedented rise in the fatality rate in the Australian mining industry over the last few years. The factors behind this rise are not clear; however, it is noted that the increase in fatalities has occurred during a fall in commodity prices.This paper examines prevention methods and systems to deal with hazards that have the potential to result in either single or multiple fatalities. Managing the risks associated with mine ventilation is used to illustrate the principals behind the approach.The paper also touches on the broad science of human error and proposes a multifaceted approach to controlling and preventing fatal risks.A summary of the steps involved in developing an effective principal hazard management plan is provided.CITATION:Clough, A J, 2015. Ensuring an effective principal hazard management plan, in Proceedings The Australian Mine Ventilation Conference, pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Bevan JE

The US Bureau of Mines is conducting research to improve the health and safety for underground coal miners, and the efficiency of the mining systems that are used. In 1986, the Bureau began a major research effort on the technology for computer-assisted mining systems for underground coal mines. The initial target was technology for continuous mining machines that would allow them to extract coal by computer-assisted operation. Technology areas being investigated include guidance systems, machine condition systems, computer systems, machine control, human-machine interfaces and planning. In each of these areas, individual system development has progressed to where underground testing of these systems will begin in 1991.In addition to coal extraction, the Bureau has also begun research for the development of technology for computer-assisted roof bolting. The Bureau is developing technology for a "smart" roof bolter that would be able to sense and analyze strata conditions to determine the requirements to provide a competent roof. The system would determine the location of the hole, drill the hole to length, and select and install the appropriate bolt.

Jan 1, 1991

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330-p.s.i. tension to 3,750 p.s.i. compression. Photoelastic examination of loaded plastic and actual rock mo.odel mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a. borehole oxtensumeter and a series of anchors at various horizons to 30 feet in a. vertical roof borehole showed that when a standing face waa.s advanced the roofmovement was practically confined to the lower two feet. The ma.j ority of this movement occurred during the 36 hours after mining at this face commenced.The use of a. radioactive isotope and a. scintillation counter in a. pair of parallel bcreholes promises to be sensitive and accurate method of roof bedding plane crack detection.

Jan 1, 1963

By Gupta A, Hall ST

The grinding characteristics of quartz which is normally associated with gold bearing ores in Kalgoorlie area was examined in a stainless steel laboratory size ball-mill in the presence of inorganic and organic surface active reagents. The cationic species considered were Fe3+, Cu2+ and Ca2+, and the anions were CO? and S2 as these are normally present during the process of grinding of gold ores in the region. The organic surfactants examined were K-amyl- xanthate, dodecylamine-hydrochloride and the Grinding Aid XFS-4272 manufactured by Dow Chemical The study was primarily based on an examination of the electrokinetic properties of quartz surface in the presence of the grinding reagents. Zeta potential at different reagent additions and pH values in the presence of individual reagents were examined and the corresponding grinding charcteristics determined. A correlation has been indicated between the grinding characteristics, as measured by the -53um size fraction produced, and the surface energy of quartz. It was observed that an

Jan 1, 1978

By Torckler L, Brathwaite R. L

At Neavesville gold-silver (electrum) mineralization occurs in steeply-dipping zones of intense fracturing, brecciation and quartz veining within rhyolitic pyroclastics, carbohaceous shales and andesites. Hydro- thermal alteration extends over an area of greater than 3 by 1.5 km. In rhyolitic tuffs, highly silicified zones containing quartz- adularia-illite assemblages are flanked by less silicified assemblages composed of albite, illite-montmorillonite and chlorite. The mineralogy ana sequence of alteration are comparable with the alteration zones which envelop the steam-producing fissures of the active Wairakei and Broadlands geothermal fields. Primary fluid inclusions in quartz from five fissure veins in the Neavesville field show maximum homogenisation temperatures ranging from 220 - 260¦C and salinities of 0.0 - 1.1 wt. % NaCl equivalent, which cover a similar range to actual measured temperatures and salinities in geothermal fluids at Wairakei aria riroaolan¦s. The age of the rhyolitic pyroclastics and related alteration and mineralization is probably Pliocene and Neavesville therefore represents a fossil geothermal system.

Jan 1, 1980

By P Bethune

Back Creek is a tributary of the Condamine River. It flows in a northerly direction across the existing Commodore coal reserves. The diversion of Back Creek was proposed to minimise sterilisation of the reserves. The approval process required a Waterworks Licence application, under the Water Resources Act 1989 (Qld), for the construction of a stream diversion channel and floodway. The diversion was designed using the æreference reachÆ approach, which mimicked existing properties of Back Creek. The following design standards were developed for the diversion: the diversion corridor width was 500 m; the diversion geometry was specified for both the low-flow channel, and the floodplain; material properties were specified for both the low-flow channel lining and the diversion bund; compaction standards for both the low-flow channel and floodplain were set; and the diversion rehabilitation included a riparian corridor and pasture land with clumps of native trees and shrubs. The following performance criteria were developed for the diversion: velocity regimes were replicated for the design events considered, in an attempt to avoid increasing the diversion flow velocities in comparison with the existing creek flow velocities; sediment transport calculations indicated that no significant change in sediment transport was expected within the diversion; overburden settlement estimates for the spoil placed in the corridor were summarised, and will be monitored throughout the construction process; geotechnical stability of the proposed Eastern Pit Buttress and the diversion bund configurations was confirmed; and groundwater impacts were assessed. Construction techniques, monitoring and further investigations are also discussed in this paper.

Jan 1, 2003

By S M. Arndt, D Tyler, F Reusch

Although significant advances have been made in understanding the mechanics of pit slopes, numerical modelling hasnÆt significantly impacted on the reliability of the design process. It is well known that legacy modelling approaches donÆt simulate large slopes well. In recent times, the emergence of very large finite element (FE) models with more than ten million degrees of freedom and the ability to simulate a large number of discrete structures, has allowed a step change in the simulation precision for slopes. The model size allows global and local effects to be realistically simulated in one model for the first time and the process can be better integrated into normal open pit slope engineering processes. Some examples of simulation of very large open pits are shown that demonstrate the challenges and some recent advances in modelling large slope behaviour. Significant limitations in the current measurement and observation regimes of open pits have been identified.

Jan 1, 2007

By Eggins SM, Crawford AJ, Maillet P

The Fiji Islands are remnants of a once continuous Solomon-Vanuatu-Fiji-Tonga volcanic arc (the Vitiaz arc), located at the boundary between the Indian-Australian and Pacific plates. They record a history of (i) arc volcanism the late Eocene to late Miocene, (ii) an extensive magmatic response to arc rifting (5.5-3.OMa) during which volcanism was dominated by shoshonitic to tholeiitic basalts, and as rifting continued, (iii) a transition from arc to intraplate volcanism. The Hunter Ridge-Hunter Fracture Zone separates the inactive South Fiji Basin from the actively spreading North Fiji Basin, and has been considered to be a transform zone, almost parallel to the motion vector of the Australian plate. However rocks dredged during the 1993 `Alize' cruise, from along the northern part of the Hunter Ridge are typical arc tholeiites, and therefore demand that subduction has occurred beneath the Hunter Ridge sometime during the last û 5Ma.

Jan 1, 1995

The development of the lower Hunter Valley, centred around Newcastle and its suburbs is closely linked to the mining of coal and the settlements which grew to house the colliery officials, the miners and their families. The Port of Newcastle expanded and developed as a port exporting coal to many ports of the world ranging from Hawaii and Brazil to Japan and Korea. The coal which passed through the Port of Newcastle, depend- ing on the historical period in question may have been mined in Newcastle itself, or one of the nearby colliery townships such as Lambton, Wallsend, Charlestown or Hamilton, or from one of the estuarine collieries located at Carrington or Stockton or from the West Wallsend area or from East Greta, Pelaw Main or Cess- nock located on the South Maitland (Greta) coal field or from the open cut and underground mines of the Singleton Coal District.

Jan 1, 1988

This paper is a summary of the general theory of sampling published by the author in 1975. Sampling is a random process and its the- ory is a study of the, numerous errors liable to take place in the course of its realization. A complete sampling scheme is a sequence of sampling (proper) and preparation stages . At each stage, the total error ET is the sum of : -.Sampling errors EE arising from the selection process itself. -Preparation errors EZ arising from the operations (crushing, transfer...) sup- ported by the sampled material. ET a EE + EZ . At each sampling stage, the (total) sampling error EE is the sum of seven inde- pendent errors : - Weighting error ED resulting from the non-uniformity of the density or rate-of-flow of the sampled material. - Integration error EI1 resulting from the long-range distribution heterogeneity of the sampled material. - Periodicity error EI3 resulting even- tually from periodic quality variations of the sampled material.

Jan 1, 1976

Major exploration companies can have a problem with what to do with small precious metal ore bodies located through exploration programmes. Low tonnage, but high grade, ore bodies too small to justify in-house development.1.2 Ban Ban Mining is a Sunshine Coast based partnership with considerable expertise in mining and earthmoving which specializes in the mining of small/medium size ore bodies on behalf of the tenement holder on a profit sharing or royalty basis.1.3 The partnership's first successful venture has been the mining and vat leaching of a small 40,000 tonne ore body with a head grade of 5 gm/tonne gold and 32 gms/tonne silver, situated near Ban Ban Springs in southeast Queensland.1.4 This paper looks at the low cost vat leaching method of treatment, as an alternative to CIP and CIL in the processing of low tonnage/high grade precious metal ore bodies.

Jan 1, 1990

By H Bartosiewi, M Kuruppu, F Mashiri

Wire ropes are one of the most heavily used components in a dragline. They are subjected to harsh conditions during the regular usage of a dragline in a mining operation. Hoist ropes are subjected to fatigue due to the cyclic nature of load handling as well as due to rope bending over the sheaves and the drum under load. This leads to wire breaks due to fatigue. Accumulation of a number of wire breaks close to each other can have a detrimental effect on the rope. Furthermore, to allow for the increasing demand for higher load capacity coupled with the inconvenience of having very large ropes, the factor of safety is often compromised, which increases the wear rate. Drag ropes are also subjected to heavy loads. More importantly, they are allowed to drag along the rough mine surface subjecting them to external physical abrasion. This makes the life of drag ropes one of the lowest among those used in a dragline. Suspension and IBS ropes are relatively uniformly loaded during their regular usage although they need to withstand dynamic load cycles as well as bending. Hence they tend to last for a number of years on average. The paper analyses the wear types and their severity of each of these rope applications, and suggests methods to determine rope wear rates and the resulting rope life. The paper further gives suggestions for good operating and maintenance practice that can extend the rope life and help reduce the large expenditure associated with every major rope change in a dragline.

Jan 1, 2005

By Ormsby W, Peters M, Van Gils H, Kehprens P, De Boorder H

The northern margin of the Arunta Block is characterized by a metasedimentary and volcanic sequence of lower metamorphic grade than that of the central Arunta Block. Whereas the Harts Ranges have granulite to amphibolite metamor- phic grades, the northern margin only reached greenschist to lower amphibolite facies. Most of the high grade area of the central Arunta Block appears to be unprospective, but the lower grade marginal fringe contains most mineral pros- pects to name a few: Barrow Creek, Molyhill and the Jervois Mine. Numerous smaller prospects occur in this marginal zone. Four major lithostratigraphic units can be recognized in the Jervois Mine area: 1. Gneissic Suite consisting of granitic and rhyolitic gneisses which are characterized by a distinct intersection lineation. 2. Metasedimentary Suite of cordierite- biotite schists and chlorite-biotite schists. 3. Mine Sequence, consisting of spotted schists with andalusite and cordierite, quartz- sericite-feldspar schists with distinct rhyo- litic remnants and quartz-sericite-feldspar schists which contain the lode horizons:

Jan 1, 1984

By B Tadesse, L G. Dyer, K Ward

The Golden Mile ore deposit in Western Australia is one of the largest gold telluride deposits in the world. Approximately 20 per cent of the contained gold in the deposit is present as gold telluride minerals, the most prevalent being calaverite (AuTe2) and petzite (Ag3AuTe2). Telluride mineralogy in the Golden Mile orebody is fine grained and complex having formed due to hydrothermal deposition in the late paragenetic sequence. Nineteen tellurium bearing minerals have been identified including gold and silver as well as mercury, lead and nickel tellurides (Shackleton, Spry and Bateman, 2003). Extensive work has been completed on the flotation of gold, gold-silver alloys and gold ores however there is a lack of information detailing the difference between flotation of native gold and individual gold minerals (Dunne, 2016). Studies on the flotation behaviour of gold ores have focused primarily on the flotation of free gold and refractory sulfides (Teague, Van Deventer and Swaminathan, 1999).

Aug 24, 2022