Search Documents

North Stradbroke Island is a large sand mass offshore from south east Queensland. Dredging for mineral sands commenced there in 1956 and the rehabilitation discussed in this paper was commenced in 1967. The frontal dunes have a long history of instability, with little vegetation prior to mining. Re-establishment of the naturally stable contours is essential, and their rehab- ilitation is described. Vegetated high dunes present different problems requiring attention to regeneration of the native species. Methods developed over the past eight years are proving successful.,

Jan 1, 1976

By D Jordan, R Wilmoth, J LeFever

Exposed, open pit mine highwalls contribute significantly to the production of acid mine drainage (AMD) thus causing environmental concerns upon closure of an operating mine. Four innovative technologies were evaluated under the US Environmental Protection AgencyÆs, Mine Waste Technology (MWTP), Prevention of AMD Generation from Open Pit Highwalls Demonstration Project. This project is funded by the US Environmental Protection Agency (EPA) and jointly administered by the EPA and the US Department of Energy (DOE) through an Interagency Agreement. The objective of the field demonstration was to evaluate the technologies ability to decrease or eliminate acid generation from treated areas of the highwall in comparison an untreated highwall area. The field demonstration was performed at the Golden Sunlight Mine (GSM) a subsidiary of Placer Dome US, located near Whitehall, Montana. GSM is an operating gold mine. The highwall at GSM was divided into five plots measuring 15.24 by 15.24 m and each technology was assigned a plot with the fifth plot being used for comparison as a background control plot. The four technologies were spray-applied. The applied in situ treatment technologies included: a modified, furfuryl alcohol resin sealant, utilising wood and agricultural by-products to coat the rock surface; EcobondTM ARD, a phosphate based process that forms a stable, insoluble compound, coating the rock surface; and two AMD passivation technologies, magnesium oxide and the Dupont technology developed to create an inert layer/coating on the pyrite, preventing oxidation. The technologies were evaluated using the following methods: ASTM D 5744-96, accelerated weathering of solid materials using a modified humidity cells; mine wall residual wall rinse sampling; microscopy; and core drilling followed by water injection testing. The following paper describes the technologies used for passivation of acid generation from the highwall, the field demonstration, and the testing results from the background and each technology plot.

Jan 1, 2003

By Ricketts N. J, Smith G. D J

A hydrometallurgical process was developed for recovery of copper from copper-lead matte formed as an intermediate product at the BHAS lead smelter at Port Pirie. A plant utilizing this process was commissioned in 1984. The leach step involves oxidation of the copper-lead matte in an oxygenated acidic chloride-sulphate leachant. The results of laboratory scale testwork from which the chemistry of leaching was deduced, are presented in this paper. The rate of recovery of copper to solution from copper-lead matte depends largely_on the availability of oxygen to the sulphide surface. The optimum leach temperature is approximately 85¦C. Free acid must be supplied according to the stoichiometry of the leach reaction: Cu1.91 S + PbS + 2.91 H2SO4 + 1.455 02 = 1.91 Cu2+ + 1.91 SOj- + PbSO4(s) + 2.91 H2O + S¦ The grind size of the matte is of minor significance. Chloride concentration in leachant should be at or above a minimum of 10.0 g/l. Chloride acts to complex cuprous ions formed during leaching.

Jan 1, 1987

By J P. Wyethe, D P. Padayache, B R. Green

The development of an ion exchange process for the recovery of vanadium from solutions containing low concentrations of vanadium and/or slurries is discussed. The process can be used to improve overall vanadium recovery throughout the plant, and/or to reduce the vanadium concentration of waste materials prior to their disposal. The development of the process on a laboratory and miniplant scale is discussed, and includes:selection of a suitable resin with the desired loading and elution characteristics; laboratory-scale testwork to evaluate the use of the resin in both resin-in-pulp and fixed bed configurations; recovery of a high-value vanadium product from the resin eluate; and a preliminary techno-economic assessment of the financial viability of the process.

Jan 1, 2000

Existing fluid flow techniques may be readily applied to the design of ranges for seam gas drainage. The Reynolds number characterises the flow regime within the pipe and it can be used in conjunction with data on absolute pipe surface roughness to determine the system friction factor. The application of the solution to the isothermal compressible flow equation utili- sing Moody friction factors and the concept of equivalent length of pipe for fittings and valves provides a practical method for sizing gas ranges. The physical capacity of a range can be decreased by the existence of significant quantities of water in the range and also by the ingress of air into the system at poor pipe joints etc. Both problems can be elimin- ated by adequate attention to design detail.

Jan 1, 1982

The Department of Resource Industries regulates and oversees safety and environmental standards for the mining and related industries in Queensland, and provides scientific support through its effort in the geosciences.The geoscientific data base accumulated over more than 120 years is very large. Therefore, accessibility to and utilisation of the data base in the most effective manner is an issue to be addressed in terms of modern information technology. The Department has developed a strategy whose implementation is progressing rapidly.

Jan 1, 1990

It is my pleasure to deliver the first Keynote Address to the first joint conference between The Australasian Institute of Mining and- Metallurgy and The American Institute of Mining, Metallur- gical and Petroleum Engineers. I am particularly pleased to be participating in this first joint meet- ing as I have been a member of one Institute for 41 years and the other for 35 years. An examination of the membership of both Institutes confirms the fact that the mineral in- dustry is an international one. This has long been the case and basically stems from the occurrence of mineral resources in most countries of the world. It is therefore fitting that these two 'Inter- national Institutes', representing the professions involved in the mineral industry, should choose `International Resource Management' as the theme of the first joint conference. The topic of this Keynote Address is `The mineral equation' or the counterbalancing supply and demand items and the factors affecting them. I propose to attempt to present the overall picture of the mineral equation as subsequent papers and sessions will deal with specific items in more detail. My thesis is broad and deceptively simple; it is that the continued existence and growth of world material civilization depends, in large measure, on the continued use and further dis- covery of world mineral resources. Material civili- zation is used as a broad term to include the pro- duction of man's shelter and tools together with the production of the `consumer' goods and ser- vices needed by society. First let us spend a few minutes looking at the development of material civilization.

Jan 1, 1978

By Dundon P

The Broken Hill Proprietary Company Limited (BHP) is Australia's largest company with widespread commercial interests ranging from steel productin to minerals, oil and gas recovery. While these interests are worldwide, the Company operates or is partner in more than 30 Australian mining ventures. BHP Engineering (BHPE) is the in-house consultant to BHP but is also the largest consultancy in Australia available to general industry. Australian Groundwater Consultants Pty Limited (AGC) is a large, independent consultancy offering specialist services in all aspects of water resources, waste management and environmental engineering, both in Australia and overseas. AGC is particularly well regarded within the mining industry and has a considerable record of providing solutions for mine water related issues. By drawing on the extensive combined experience of AGC and BHP Engineering, this paper will summarize some of the unique ways in which water interacts with and impacts on mining operations in Australia, particularly in matters such as: Slope Stability Drainage and Dewatering Production Cost (Transport, Drilling, Blasting, etc) Water Supply Water Management Tailings and Waste Management Environmental Issues. The paper will also illustrate the cost benefit of providing major engineering works for reduction in total mining cost. It will be shown that, through advance planning and close interaction between outside experts (ie consultants) and on- site personnel, very significant operational cost savings can be made while at the same time achieving a safe and responsible mining environment.

Jan 1, 1988

Interest in mineral sand mining in the south west corner of Western Australia began in the late 1940's and significant production commenced in 1956. Early land use conflicts arose because of conservation implications (Ludlow tuart forest), expanded to include post-mining rehabilitation requirements (the Wonnerup mine near Busselton) and today include some agricultural/mining disputes. These latter conflicts are largely caused by the need for mining companies to secure longer-term reserves. To date, deposits containing mineral valued at A$440 million have been sterilized and are unlikely to become available in the future. There is additional pressure being placed on presently available reserves and a pessimistic picture could be drawn, whereby the southwest mineral sands industry ceases to exist by the year 2010. However, sensible land use planning, the support of policticians and the community, and responsible attitudes towards compensation and rehabilitation could, in combination, see the industry maintain significant mineral output until the middle of the 21st century. Examples of deposits sterilized by adverse land use will be given.

Jan 1, 1986

Structure is the most important control on the location of hematite deposits in the Hamersley Province in the Pilbara region of Western Australia. Unravelling the structural history of mineralised areas, however, is complex because the Province underwent three orogenic events, and three regional extension events followed the main episodes of compression. Steeply E to ENE dipping normal faults immediately predated deposition of the Beasley Quartzite of the lower Wyloo Group after the Ophthalmian Orogeny. Steeply NE and SW-S dipping normal faults predated deposition of the McGrath formation of the middle Wyloo Group, following the Panhandle Orogeny. The resulting interpreted rift was subsequently reactivated and tilted during the Capricorn Orogeny. Late NE trending normal faults are confined to the eastern half of the Province. High-grade hematite deposits occur in rocks that range from intensely folded (Mt Whaleback, Giles Mini) to rocks with less, or only little deformation (Paraburdoo, Channar), suggesting that folding had at best limited influence on ore genesis. In contrast, extensional normal faults are always associated with high-grade hematite deposits, and in particular faults that link the underlying dolomites of the Wittenoom Formation with the overlying iron formation, thus providing a pathway for mineralising alkaline fluids.

Jan 1, 2005

This paper will discuss Fordertechnik dawatering screens and their application in process industries. Fordertechnik screens were designed for the dewatering of deslimed, wet fines materials encountered in the mineral beneficiation, sand and coal processing industries. However, these screens have also been used in such industries as municipal waste treatment, paper pulp, chemicals and the food industries. Fordertechnik screens are of simple design and, as a result, offer low capital and maintenance costs. The design is based on the use of twin counter-rotating vibratory motors which provide high frequency, low amplitude linear movement of the screen deck which is essential for high production requirements. Fordertechnik dewatering screens are engineered and manufactured in Australia by Mitchell Cotts Engineering under licence to Fordertechnik GmbH of Mulheim, West Germany

Jan 1, 1984

The P49 Shaft, Hilton Mine, was sunk and equipped for Mount Ise Mines Limited by con- tractors Cementation - Thiess Joint Venture. The leached siltstones to a depth of 150m were known to contain large volumes of water. These siltstones were cored and tested in the laboratory. Field results confirmed that cement grouting was relatively ineffective but that chemical grouting was effective. The Sm diameter shaft was sunk to a depth of 1040m. Weak strata to the full depth re- quired continuous temporary support by rock bolts and mesh before the concrete lining was poured, and made sinking conditions difficult. After completion of the shaft sinking the headframe was redesigned and modified to allow shaft equipping as a combined service and hoisting shaft with seven compartments. The shaft steelwork was designed and fab- ricated for service with high speed conveyances operating under corrosive conditions. The steelwork, weighing approximately 1500 tonnes, was installed to a high degree of accuracy which required guides not to depart from true verticality by more than 2mm over any 5m, or 15mm over the full shaft depth.

Jan 1, 1976

The limitations of the conventional practices, and their effects, in prospecting for and in the evaluation of alluvial gold deposits are briefly reviewed. Geophysical prospecting methods have demonstrated their complementary role in the delineation of deposits by reducing the number of boreholes which are primarily of a 'probing' type. Larger diameter boreholes, although more expensive on a linear basis, are much cheaper on a volume recovered basis. The need to have sufficient volume as well as number of samples is stressed. Classical statistical methods are not appropriate for such deposits as there is sufficient structure, or spatial correlation, to require the application of geostatistics. Quite reliable semi-variograms, but not in all cases, of the spherical scheme have been obtained. Subsequent kriging has, to date, been confined to unworked deposits: retrospective estimates to compare to production have not therefore been produced. However, the technique shows promise but indicates a considerably greater borehole density (of the conventional diameter) may be necessary to produce confident estimates. Used in conjunction with larger diameter boreholes, a lesser borehole density may be sufficient, through radical reductions of the sampling error.

Jan 1, 1977

By I D. Hair

A numerical groundwater model was used to predict the nature of interactions between heavy mineral sands mining operations and the groundwater regime at North Stradbroke Island, Southeast Queensland. North Stradbroke Island is formed mainly of massive vegetated Cainozoic aged dune sands. Since the 1950s, a number of operations have mined rutile, zircon and ilmenite on North Stradbroke Island. In such mining operations, a dredge and an associated processing plant are floated in a pond either above or below the prime groundwater table The numerical model was based on the North Stradbroke Island Groundwater Management Model, developed in 2001 by the Department of Natural Resources and Mines (NR&M). This model was constructed using the modular, cell-centred, finite-difference groundwater flow model, MODFLOW, developed by the United States Geological Survey (USGS). The NR&M model was refined to improve model resolution and detail for simulating dredge mine paths. Of particular interest were: water table fluctuations induced by mining for the identification of slope stability risk; the optimisation of sand spear arrays supplying mine make-up water requirements; inflow and outflow rates to the dredge pond for overall mine water balance; and interactions with Eighteen Mile Swamp and water supply bores controlled by the Redland Shire Council (RSC). Depending on the water level in the dredge pond compared with the surrounding groundwater table, water either flows out of the dredge pond into the groundwater regime or from the groundwater system into the dredge pond. The MODFLOW river package (RIV) was utilised for the modelling study. Dredge pond movement was simulated using specialised software developed by Watermark Numerical Computing (WNC) to interpolate pond positions and map the dredge path to the model grid both spatially and temporally. As tailings placement affects the groundwater system through increased recharge, the MODFLOW recharge package (RCH) was utilised to simulate different recharge efficiencies. Long-term model predictions were made for the period from July 2002 to May 2021. Results of the modelling showed that exchanges of flow between mining operations and the groundwater regime could be effectively managed. The study provided valuable information which was used to develop an appropriate mine water management plan.

Jan 1, 2003

In the course of an investigation of the influence of bismuth on copper carried out some years ago, (1) the author found that phosphorus exerted a beneficial effect on bismuth-copper alloys of low bismuth and oxygen content by neutralizing the embrittling effect of the bismuth. In the intervening years, a further examination of bismuth-phosphorus-copper alloys has been canied out and the influence of other elements and combinations of elements on copper containing bismuth has been studied.The results recorded in the present paper are part of this investigation.MATERIALSAll the alloys were made from high-grade copper (KS.A. wire-bar) of the following composition: copper 99·95%, oxygen 0,040'%, iron 0·0015%, sulphur less than 0-001%, bismuth less than (j>'OOl%, other elements each less than O· 0010/<-. The bar was hot rolled and cold drawn to strip which was cut into short lengths and cleaned in nitric acid ready for melting.A piece of this 'strip was drawn to wire 0·08 in. diam., annealed at 5000 C, and measured for electrical conductivity as a check on purity. The result was 101·5% of the I.E'.C. standard.In making the alloys, phosphorus was added as 14% phosphor-copper, bismuth as 17% bismuth-copper, and the other constituents either as copper alloys or as elements of a high degree of purity.PREPARATIQN OF STRIPSThe charges were melted in plumbago crucibles (Morgan salamander brand) in an oil-fired furnace, Le;, in the manner commonly adopted in industrial practice. The copper was first melted under charcoal, well stirred with a chaned stick, and the necessary alloying elements added and stirred in with the stick. The weight of a charge varied according to requirements but generally was about 4 lb. The charges were poured into slightly tapered brass moulds heated to about 1000 C and dressed with a mixture of mineral oil and tallow. They were not only poured under charcoal through the burning mould dressing but also- through a ring of flame produced by burning kerosene on asbestos cord wrapped round the top of the mould. Experiments carried out with plain copper proved that by this means oxygen could be excluded from the stream of metal. The billets were 7·5 in. long x O·83 in. diam. x 1·3 lb. weight.The billets were cropped about 1 in. from the top, cleaned in nitric acid, and measured for density by the usual method of weighing in air and -in water. As these measurements were required only as a check on casting, technique a high degree of accuracy was not essential (accuracy = -+ 0·2%).

Jan 1, 1942

HISTORY OF PROCESS DEVELOPMENT The manufacture of coke from coal commenced at the beginning of the 17th century by heaping coal into circular mounds in the open, covering with earth, clay or ash and slowly burning the coal in the mounds to produce a heap of coke. Naturally the process was slow in production rate with low coke recovery due to the loss of that part of the coal which was completely burnt to ash. As a natural consequence of this initial carbonisation method, a coke oven design was developed so that the coking chamber, which was constructed of brick, was circular in plan, cylindrical in section with a dome shaped roof - similar in shape to the original coal mounds. As the shape of the chamber was similar to the old dome shaped beehive, the ovens were called beehive ovens. The ovens were built in long single or double rows with retaining walls between each oven and as such were known as a battery of beehive coke ovens. In these early beehive ovens, coal was charged from hand wheeled tubs into a hole into the top of each oven, hand- levelled with a rake and the oven side opening sealed with bricks and clay except for some small holes in the opening to admit limited quantity of air for combustion. Coking commenced by the heat retained in the brickwork from the previous charge. The gases evolved from the coal, together with the admitted air, were partially burnt inside the oven to supply the heat for carbonisation and the surplus gases were burnt to waste at the top charging hole. The heat from this gaseous combustion inside the oven together with the reflected heat from the brickwork of the arched roof of the oven allowed carbonisation of the coal charge to proceed from its surface slowly downwards to the floor of the oven. At the end of the coking cycle (usually 4 or 5 days) when there was no more evolution of gases, as indicated by diminishing gas flame and a drop in oven temperature, the brickwork of the oven opening was removed. The coke was then quenched by inserting a pipe with spray holes to spray water over the coke charge in the oven after which the coke was raked from the oven. The work of charging and levelling the coal, bricking and removal of oven opening, quenching and raking out the coke all required manual labour. As these ovens only carbonised a 5 to 7 ton charge of coal per cycle of 4 to 5 days, to produce 3 to 41/2 ton of marketable coke, the labour required per ton of coke was high.

Jan 1, 1975

The number of employees required to operate a continuous operation was determined. The fixed and variable costs of the operation were separated, generally along the lines of labour and stores components. Proprietary `MicroPlanner' scheduling software was used to assess resource utilisation under the constraints generated by seven-day operation to determine the level of resources required and ensure that the maximum use was being made of all resources. The mine economic model was used to account for both the fixed and variable costs of the various task to determine the cost and net revenue of the various scenarios. The analysis indicated that mine output could be increased while reducing the unit production cost. Several eight- and 12-hour, seven-day rosters were sourced and ranked for their potential to improve production and communication, and for their effect on employee health and lifestyle.

Jan 1, 1995

Mining and metallurgy are more capital intensive than all other industry in Australia. Capital demands are met by domestic and foreign sources of finance for whom the major constraints are the supply of funds and factors of risk and uncertainty. in both mineral development and institutional financing policies, specific options are available to administrators which would allow mining to benefit from a more reliable supply of capital. The strength of major partners involved and overseas participation are important aspects of financing mineral developments. Future changes in financing for the mineral industry are considered most likely in variable interest rate funding, in the leasing of major plant items, and in the development of flexible techniques to ease the burden of infrastructure costs. In a consultancy sense, financiers are available to mining to assist with and to advise on optimal develop- ment of mineral industry projects.

Jan 1, 1975

Mathematical economic models for assess ment of technological progress in the mining industry in the USSR are discussed. The models are based on a simple index, TT which approxi- mates the rate of growth of the people's living standards. However, for application in the mining industry it is necessary to incorporate various parameters to account for the dynamic charges in the geological, mining and other technological conditions. Derivations of the models are shown and examples of results are Included.

Jan 1, 1977

Mine planning is difficult. Even for small operations, it involves reasoning with complex variables and the practical difficulties of mining. It is also about predicting and planning the future in an unpredictable physical and economic environment. Yet we rely on a handful of individuals and their spreadsheets to tell us how to do it û planning the business and activities of mining to hopefully produce results that will please stakeholders. Does it work? Not as well as it could. Planning affects everyone in the organisation. Company executives are demanding more reliability and stability in cost and revenue forecasts from their operations. Management want to explore ways of being more cost effective. Miners and contractors want more useful plans and realistic targets. And the planners have to describe the method that will translate business objectives into implementable plans. Even with the use of computer technology a lot of effort is expended to produce plans that are largely qualified by the level of knowledge and experience of individuals. Better use of information and the application of Intelligent Technologies can improve the quality and reliability of mine plans and schedules. By capturing the knowledge within the organisation and speeding up the planning process, Intelligent Technologies allow more options to be considered more rigorously. But it is not just about technology. It is about how technology is implemented and embodied in the way the business is managed for performance. When this happens, the real benefits of better planning start to flow.

Jan 1, 2003