Search Documents

By Richardson G. W, Yap L. C

Friction rock stabilisers (FRS) are steel-based, thin-walled tubular ground reinforcement widely used in underground mines in Western Australia. Following installation these stabilisers are subject to corrosion which may reduce the load carrying capacity and lead to unexpected ground falls. Although corrosion has been recognised as a common occurrence, particularly under aggressive mine water and mineral conditions present in underground mines, the knowledge of the effects of corrosion on the mechanical behaviour of FRS is limited. The Department of Minerals and Energy of Western Australia has conducted a laboratory based program of studies to investigate the effect of corrosion on the mechanical properties of FRS. The studies have focused on the effect of corrosion on tensile strength of FRS and frictional resistance along the interface between FRS and the drillhole wall. The results indicate that under certain conditions corrosion damage can significantly reduce the effectiveness of FRS.

Jan 1, 1996

By Hawes GW

Until 1980 copper, lead and zinc sulphide slurries have been success- fully dewatered for rail and sea transport for many years at the Rose- bery site of North Broken Hill Holdings Ltd. utilizing conventional vacuum disc filtration systems. An upgrading and mill expansion program completed in 1981, which also permitted the introduction of ore streams changes, had resulted in difficulties dewatering copper and lead sulphide slurries to comply with transportable moisture limits. Following an extensive investigation which included both laboratory and pilot plant testing a program was commenced to replace the 2 vacuum disc filtration systems with 2 pressure filtration systems for use on copper and lead slurry dewatering and also to retain other existing vacuum disc filters as standby. An analysis of mill operations performance resulted in slurry storage tanks with a capacity equivalent to 20 hours of normal production being incorporated into the project. The pressure filters are mounted above the concentrate stock- piles. A sealed sloping floor incorporating launders is used to prevent any accidental contamination of the concentrate from pipe leakages, spillage, or from water hoses used for clean up purposes around the area. The project was completed in 1985 and operating performance has been better than that predicted from testwork. Equipment availability at 95076 together with the slurry storage capacity provided results in minimal requirement for the standby vacuum filtration system. Some typical operating results are given.

Jan 1, 1988

By Pinn N

Geosynthetics is an all encompassing word to describe a number of man-made products usually from hydrocarbons which are used in conjunction with the soil. The specific products are:Geotextiles Geomembranes GeonetsGeogrids GeocompositesIn mine establishment and associated construction work, Geosynthetics have proven to be successful in a wide range of applications. For example, geotextiles are now used to assist with the establishment of access roads, site preparation, haul roads and in connection with the construction of embankments for storage ponds and dams as well as for general hydraulic and foundation engineering problems.

Jan 1, 1990

The BHP Steel Group embarked on a Total Quality Control (TQC) programme in 1984 in response to enquiries from a major customer regarding procedures for quality in materials supply.The TQC initiative has been adopted by all seven Divisions of the Steel Group and covers a broad and comprehensive range of management and workforce improvement initiatives.The development of the TQC initiative in the Collieries Division of BHP Steel over the past eighteen months has resulted in important experiences and leanings.

Jan 1, 1991

By Ramsay WRH

The Mount Stavely Volcanic Complex compri- ses one of a number of northerly trending fault bounded greenstone occurrences in Western Vict- oria, of probable Cambrian or older age. The greenstone belt is coincident with several linear positive aeromagnetic anomalies, which outline the surface and subsurface extensions of these greenstones. Mapping at Mount Stavely has identified serpentinite, variolitic basalt, two-pyroxene and pyroxene-hornblende andesite, dacite, rhyodacite and their pyroclastic equiv- alents. Chemically and mineralogically the volcanics constitute a calc-alkaline assemblage. The mineral potential of the region has been enhanced following a discovery by Pennzoil of Australia Limited near Ararat, of sulphide min- eralisation containing approximately 1 million tonnes at 2.7 percent copper. The volcanic environment of the Mount Stavely Volcanic Complex is discussed in terms of similar environments found in Canada.

Jan 1, 1982

Two separate mine rehabilitation programmes carried out by Australian Consolidated Industries Limited (A.C.I.) in South Australia at Normanville and Port Lawler are discussed. Emphasis is given to the methods used, the results achieved and to possible future improvements.

Jan 1, 1976

By T Kitajima, T Kawaguchi, T Nakamura

Carbothermic reduction of iron oxide is an attractive mechanism to produce metallic iron, since it can directly utilise coal as both reductant and fuel. To improve energy efficiency and productivity of the metallic iron production based on this mechanism, the combustion bed process packed with the composites of iron oxide and coal powder was experimentally evaluated. The process has a potential of high heat efficiency since it can automatically utilise the heat of reduced materials as that necessary to the subsequent reduction of the composite by a large heat exchange rate between the packed particles and gas flowed across the bed. However, it is hard to perfectly prevent the reoxidation of formed metallic iron in the bed. The present paper reports the effect of coal content, pellet size and so forth on the reduction/metallisation degrees of the samples after the reduction experiment. It also discusses the effect of pretreatment of the composite pellets using CaO bearing materials to suppress the reoxidation of formed metallic iron in the bed.

Jan 1, 2000

By P Voigt, B Lumsden, P Lines, I Gurnett

Plant tests of magnetic conditioning have shown increased flotation recovery of paramagnetic sulfide minerals (chalcopyrite, sphalerite and pentlandite) in the -38 ¦m size fraction within rougher and cleaner flotation circuits. A statistical plant test was undertaken in the Mount Isa zinc flotation circuit where magnetic conditioning was tested simultaneously in both the rougher circuit and the cleaner retreat circuit (cleaner scavenger). This test resulted in a normalised increase of 1.60 per cent in the rougher circuit zinc recovery and simultaneously a normalised increase of 4.60 per cent in the cleaner retreat circuit zinc recovery - to a very high level of statistical confidence. Interestingly, in a novel approach, it was possible to verify the plant test results in two ways. Firstly, detailed MLA analysis of the tails confirmed the statistical plant test results and showed that the greatest effect of magnetic conditioning was on the sphalerite in the C3 - C6 size fraction, where there was a reduction of around 15 per cent in zinc in tails. Moreover, there was a reduction of around 15 per cent in liberated sphalerite across all -38 ¦m size fractions, but only a seven per cent reduction in non-liberated sphalerite in the tails. Secondly, plant modelling showed that increasing the rougher zinc recovery would cause an increase in zinc feed grade to the cleaner retreat circuit. The increase in the zinc feed grade to the cleaner retreat circuit with magnetic conditioning was demonstrated to a very high level of statistical confidence.CITATION:Gurnett, I, Voigt, P, Lumsden, B and Lines, P, 2012. Magnetic conditioning of sphalerite at XstrataÆs Mount Isa Zinc Operations, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 233-240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

THE millng methods employed in the Mount Lyell Mining and Railway Company's mines are, perhaps, less known to the milling world than those of other important districts, due to the geographical remoteness and isolation of the Mount Lyell field,but they present many features which are unusual, and should be of interest to the mining engineer. Typical mining is carried out on an open-stope system, details of which are the result of local experience and evolution, and of which the outstanding feature is that the ground is so worked as to be largely self-supporting by virtue of domical form given to the stope roofs. It is locally termed "rill" stoping,' but differs widely from what is generally understood by that designation, chiefly in that the "rill" or slope is developed in every direction from a central focus, and not merely in directions followllig the strike of a lode or ore-body whose longitudinal dimensions are very much greater than its width. Such terms as "donie stoping" or "arched-back stoping" would be more appropriate and descriptive.The company's active operations' at the present time extend to the Mount Lyell and North Lyell mines, and, though the fundamental principles of stoping methods are the same in each, the dissimilarity of the ore-bodies, both in nature and mode ofoccurrence, necessitates considerable variation as to details to meet the respective conditions. The Mount Lyell pyritic body lends itself to the adoption of the .system in its simplest and almost ideal form, and a description of stoping in this mine willserve best to illustrate it, while later reference to details of practice in the North Lyell mine will indicate how it may be varied to meet more difficult circumstances.

Jan 1, 1915

The conventional approach to the disposal of fine coal mine tailings, which involves piping the tailings as an aqueous slurry to a storage where they remain in the form of a permanent wet deposit, is becoming unacceptable. This approach is a legacy of a "contain and forget" mentality, which has economic advantages only in the short term. In the longer term, wet tailings deposits occupy large areas of land and present extreme rehabilitation difficulties. Alternative tailings disposal systems, which are sustainable and which facilitate rehabilitation, are required. The possible alternatives include the mechanical dewatering of fine tailings prior to disposal in combination with coarse reject, tailings disposal into spoil pile valleys, and the combined pumping to disposal of tailings and coarse reject. The most appropriate choice of fine tailings disposal strategy will vary from mine site to mine site. The chosen strategy should be optimised to meet increasingly stringent environmental requirements, within the constraints imposed by each mine. The alternative approaches represent significant departures from past practices, and require considerable industry driven research and development before they can be adopted with confidence. All three alternatives involve mixing of the fine tailings and coarse waste streams, aimed at creating a mixture of reasonable engineering properties. Understanding the engineering behaviour of such mixtures is central to the success of these alternative disposal strategies.

Jan 1, 1991

By Blom MS

Two well-developed styles of mineralization occur in the Nevados del Famatina mining district, Famatina ranges, La Rioja province, Argentina. Porphyry molybdenum- copper-gold mineralization and high level acid sulphate alteration/mineralization (Nevados del Famatina) are related to intrusion of the Pliocene Mogote rhyodacite porphyry complex. High sulphidation epithermal mineralization (La Mejicana) is developed peripheral to the Nevados del Famatina deposit. Both are hosted mainly by the Ordovician Negro Peinado metapelites.At Nevados del Famatina, five mineralized fracture events have been identified and correlated with four distinct alteration assemblages. Stage I (barren quartz) and stage II (molybdenite¦sphalerite¦pyrite) mineralization are associated with a K-silicate alteration assemblage of K-feldspar+biotite+quartz+magneti te¦ilmenite¦anhydrite. Stage III (bornite+pyrite+sphalerite+molybdenite ¦chalcopyrite¦idaite) and stage IV (chalcopyrite+pyrite +sphalerite+gold¦tennantite-tetrahedrite) mineralization are related to a quartz-sericite assemblage of quartz +phengite+illite+pyrite+rutile. Stage V mineralization is divided into two substages. Stage Va (chalcopyrite +pyrite+sphalerite¦ tennantite-tetrahedrite ¦ tellurides ¦ gold ¦enargite¦famatinite¦stibnite¦molybdenite) is related to a sericite-clay assemblage of quartz+illite+kaolinite ¦montmorillonite¦alunite. Alunite-kaolinite alteration (alunite+pyrophyllite+kaolinite+ aluminum - phosphate -sulphate minerals ¦illite¦fluorite¦corundum¦anhydrite) occurs in the upper part of Nevados del Famatina associated with the later stage Vb (quartz+famatinite +chalcopyrite+covellite + chalcocite ¦ marcasite ¦ enargite ¦ luzonite¦sphalerite¦melnikovite) mineralization.

Jan 1, 1990

Gold occurs at Mt. Charlotte associated with a stockwork of pyritised quartz veins in Unit 8 of the Golden Mile Dolerite. The ore- body is massive, 200m long and 40m wide and has been proved to over 600m below surface. Mining is by sublevel ring drill stoping with the ore recovered by diesel powered equipment. Ore reserves are based on traverses of diamond drill holes oriented to produce an equal intersection width on the two principal sets of quartz veins. Assay and geological boundaries are marked on each drill section and this boundary is transferred to mine plans and cross sections. Ring-drilling patterns are based on the cross sections and the resulting mining outline is transferred back to the drilling sections. The mine ore reserve is calculated from the mining outline.

Jan 1, 1979

of the multitude of physiographic problems of immediate interest in volcanic terranes, it is the origin of the magma forming the magnificent volcanoes that is perhaps the most mysterious. Unlike anywhere else on earth, the possible locations of magma production beneath the convergent margins are strongly limited in depth and areal extent. Yet the exact process by which magma is produced still stands elusive, even in light of tremendous gains in analytical and physical insight. The principal aim here is to discuss some of what has been revealed about the physics and chemistry of the origin and evolution of island are magmas.

Jan 1, 1987

A case-study is presented of the tailings dam of Nairne Pyrites Pty. Ltd., at Brukunga, South Australia. The methods of-construction and operation of the dam are outlined over the whole working life of the mine. Procedures of soil mechanics used to estimate the stability 'of the face of the dam are described, and seepage problems are dis- cussed. It is concluded that the dam is basically stable, and enabled Nairne Pyrites Pty. Ltd. to dispose of tailings economically, although more attention to seepage control may have been ad- vantageous. Suggestions are made on the construction and operation of tailings dams elsewhere.

Jan 1, 1975

By Robertson A. D C, Cranfield L. C, Murray C. G

Most base and precious metal mineralisation in the Gympie Province is genetically linked to intrusion of branitoids of Late Permian to Late Triassic age. Most lodes are hydrothermal quartz and quartz-calcite veins at intrusive contacts, within either the granitoids themselves or the country rocks, and commonly associated with dykes. Other types of intrusive related deposits are disseminated porphyry type Cu, base metals in skarns, and Mo in quartz pipes and veins. Although the Late Permian-Late Triassic granitic intrusives can be subdivided in terms of age, it is not yet possible to relate deposits of particular metals or styles to granites of a specific age on a regional scale.Some significant mineralisation is not associated with granitic intrusions. This includes the Gympie goldfield, by far the largest known deposit within the Gympie Province. Gold occurs in quartz veins crosscutting Early Permian volcaniclastic sediments and also in NW striking fault zones. The source of the mineralisation is unknown. Gold and silver also occur in epithermal, disseminated and breccia hosted deposits within Late Triassic continental volcanics. Epithermal Hg mineralisation at Kilkivan may be related to Early-Middle Triassic volcanics.

Jan 1, 1990

In recent decades the awareness of environmental issues by the general public has developed at an accelerat- ing rate. This is the result of a number of factors including more scientific knowledge of environments and of the impacts of modern society upon them, higher levels of education, the opportunity for people to travel more, and the success of the various communication media in bringing in- formation to the communities of the world about such environmental crises or threats as the smogs of Los Angeles and London, the Torrey Canyon and Santa Barbara oilspills, Minamata disease in Japan, the spread of the Crown of Thorns starfish, the disposal of toxic industrial wastes into the Upper Rhine, the discovery of high mercury and zinc contents in marine foods in southern Australian waters, and the proposal to mine limestone at Precipitous Bluff in Tasmania.

Jan 1, 1975

By Bolton G. C

Experiments were conducted to access the feasibility of removing zinc from lead slag by sulfation or chlorination or both. Gaseous sulfation with sulfur dioxide and oxygen released only 50 per cent of zinc even under the most severe conditions. Sulfation with concentrated sulfuric acid by a fast-leach process released 95 per cent of zinc while pug-roasting released a maximum of 78 per cent of zinc. Chloridization with NaCi in the presence of sulfating gas released 50 per cent of zinc, while direct chlorination with chlorine gas and oxygen released 85 per cent of zinc and 100 per cent of lead in a chloride condensate containing little impurities.

Jan 1, 1980

By Royston, Woods R

ANI Bradken Vortex Pulp Lifters and Grates, both as original equipment and retrofitted to existing SAG mills, are now in field operation. The development of the Vortex leading curve pulp lifter was based on an analysis of traditional radia

Jan 1, 1997

The problem of manufacturing from sulphuric 'acid and Christmas Igland "A" phosphate, superphosphate of acceptable physical condition and agronomic phosphate availability, is directly related- to the crystallisation of a reac- tion product, monocalcium phosphate monohydrate. Two solutions to the problem, vacuum drying the superphosphate and calcination of the ore before reaction with acid, are discussed.

Jan 1, 1971

By Gordon A. R

The effect of various types of solid carbonaceOlls reductants on the rate of fuming of zinc from lead blast furnace slag was investigated at I250°C.The results of the laboratory experiments indicated that the rate of removal of zinc from slag depended primarily on the volatile matter contents of the reduclants. The effects of fixed carbon, moisture and ash contents were less significant.

Jan 1, 1992