Search Documents

Most types of nuclear power reactors use uranium dioxide fuel. Power reactors using natural uranium dioxide fuel are of special interest to countries such as Australia that have their own uranium supplies. A wide range of uranium dioxide powders can be fabricated and the ideal one flows readily, presses without the need for binders or lubricants, sinters to the required density and gives low reject rates at all fabrication stages. Sinterable uranium dioxide is usually produced via the ammonium diuranate route.The Australian Atomic Energy Commission is aiming to demonstrate production of nuclear grade uranium dioxide from Australian concentrates, improving technology where possible. Details are given of the dissolution, solvent extraction, precipitation, filtration, drying, and· calcination-reduction steps. Solvent extraction from sulphate media is also under study with a view to developing a process to produce a nuclear grade product at the mine treatment plant site.

Jan 1, 1970

By K Cameron, S Strohmayr, J Wallace

In 2012, a single module heavy medium cyclone plant (HMP) was installed at the Glencore Zinc’s (then Xstrata Zinc) McArthur River lead zinc mine. The HMP formed the first part of the MRM Phase 3 Project to increase run of mine (ROM) capacity from 2.4 to 5.5 Mt/a.The purpose of the HMP is to remove liberated gangue from the crusher product at minimal loss of valuable mineral. The McArthur ores are very finely disseminated requiring a fine primary grind size prior to rougher flotation. Rejecting waste prior to grinding therefore offers significant power and grinding media savings. The plant was designed to treat only those ores with a reasonable upgrade ratio at the target zinc recovery across the HMP of 95%.On this basis, a 1.8 Mt/a single module plant was built based on 250 t/h feed rate and 82% availability. In contrast to existing base metal heavy medium plants in Australia, the MRM Flow sheet utilised the principles in modern coal heavy medium cyclone plant design. Since commissioning, the plant feed rate has been significantly increased and is now normally operated up to 540 t/h (dry basis).Although this throughput increase is partially due to debottlenecking work, it is also attributable to the conservative design parameters for base metal heavy medium cyclone circuits in comparison to those used in equivalent coal circuits.This paper discusses Flow sheet design and compares traditional base metal design parameters with those achieved at MRM and those of modern coal plants. It provides information on plant capital and operating costs and the net savings realised by its installation. In addition to power and grinding cost savings, the paper also highlights the savings in water through rejection of near dry waste and reduction of tailings pumped to the storage dam.CITATION:Wallace, J, Strohmayr, S and Cameron, K, 2015. McArthur River Mine heavy medium plant – the benefits of applying modern coal plant design principles to base metal heavy medium separation, in Proceedings MetPlant 2015, pp 311–323 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Bibby P. A, Leupen R. A

A 24,300 tonnes per year state of the art Silicon smelter is being constructed for Barrack Silicon Pty Ltd at Kemerton, 20 kilometres north of the City of Bunbury in Western Australia. The plant is designed for the reduction of high purity quartzite lump to metallic silicon in two 27MVa Demag submerged arc electric furnaces. The primary reductant, a high purity charcoal, will be manufactured at the plant from locally sourced jarrah wood waste (Eucalyptus Marginata). Commercial silicon production is scheduled to commence in October 1989. Keywords: Silicon, Smelter, Quartzite, Furnace, Charcoal, Jarrah, Wood, Eucalyptus Marginata.

Jan 1, 1989

A method for the detection and analysis of tin in cassiterite ores is discussed. An empirical relationship was established between the tin content of an ore sample and the percentage absorption that this sample produced in a Mossbauer experiment. The time taken to complete an assay with this method is much less than with any of the methods currently in use. The equipment can be adapted readily for use in the field.

Jan 1, 1969

By T Sylow, A Correa De Araujo, M Gotelip Barbosa

ArcelorMittal is among the largest world’s producers of iron ore. With a geographically diversified portfolio of iron ore and coal assets, it is strategically positioned to serve the network of steel plants, as well as supply the external global market. ArcelorMittal Mining has a global portfolio of 14 iron ore operating units across Brazil, Bosnia, Canada, Kazakhstan, Liberia, Mexico, Ukraine and the United States. Iron ore products include concentrate for sintering and pelletising, pellets, directly shipped fines and lump ore. This paper presents an overview of ArcelorMittal iron ore mines including iron ore typologies and the annual production of each unit. It will also briefly discuss the processing required in order to obtain marketable products.CITATION:Gotelip Barbosa, M, Correa De Araujo, A and Sylow, T, 2017. Overview of ArcelorMittal mining operations and research and development, in Proceedings Iron Ore 2017, pp 161–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Wilson O. A

TABLE OF CONTENTS1. Introductiona. Process Changes since 1939.b. Current Practice.2. Ore Characteristicsa. Copper Minerals.b. Gold Occurrence.3. Treatment of High Grade Acid Orea. The Ore Treatment Planti. Coarse Crushing SectionDust Controlii. The Concentrating MillDesliming SectionGranular GrindingGranular FlotationGranular Flotation ReagentsFlotation MachinesSlime FlotationConcentrate CleaningConcentrate Handlingiii. Scavanging No.1. Mill Granular Tailings at No. 2 MillRegrinding UnitScavenger Flotationb. Pyrite Productioni. Pyrite Flotationii. Pumping of Pyriteiii. Storage of Pyriteiv. Pyrite Loading

Jan 1, 1952

The commonly used Stopes-Heerlen coal petrographic classification and nomenclature has over the years been subject to variable interpretations. This paper discusses the problem with specific reference to the inertinite maceral group. The effect of various interpretations of the Stopes-Heerlen system on maceral analysis is discussed and illustrated by means of comparative analyses conducted by a number of laboratories in Australia.An attempt is made to define the reflectance thresholds used by the authors to subdivide the inertinite group; the genetic and technological significance of these thresholds are compared.The difficulties of distinguishing structured and nonstructured macerals of the inertinite group are discussed in terms of possible improvements to the present StopesHeerlen system by extending the classification to include transitional maceral types.

Jan 1, 1970

The development of research activities at Risdon and the implementing of a policy of instrumentation in plant processes have, in recent years, entailed a considerable increase in research staff and created an urgent need for more space and modern laboratory facilities. The existing laboratories have been in use for 25 years and are now inadequate. New buildings have been authorized.The new buildings will comprise, firstly, a laboratory building of three floors giving a totai .floor space of approximately 11,000 sq.ft., and a pilot plant building as an annexe to the laboratory building, of approximately 4,900 sq.ft. The laboratory building will accommodate from 20 to 22 research workers, and additional plant operatives will be used for the control of processes in the pilot plant building. The new buildings are designed to provide facilities for three principal functions; the investigation and improvementof existing processes, the development of new processes up to the pilot plant stage, and the control and maintenance of instruments.LOCALITY AND ORIENTATION OF BUILDINGSThe site of the buildings is elevated ground on the eastern side of the main plant, near the main entrance and general office building. There will be no obstruction to sunshine at any time of the day, and the laboratory building will command views of wide radius from wooded hills across the River Derwentto the open sea on the south-eastern quarter.The buildings are located to provide space for future extensions. The main laboratory building faces approx...

Jan 1, 1949

A comprehensive analysis of rock structures in non-oriented (axially oriented) drillcore is now available (Laing, in press). The system embodies new concepts which better equip the geologist and engineer to deal from the outset with optimising the acquisition of structural information in drillcore, logging: interpreting, and graphically presenting the results. The few existing techniques for determining orientations of structures are augmented by a wide range of new techniques, and all are brought together into two solution types by considering the underlying Euclidean geometries. Analysis of these solution types in terms of what data are required to implement each solution and what assumptions need to be made, leads to strategies which facilitate intelligent design of different drilling programs for blind and outcropping situations. Drillcore is variably structurally fertile, depending on the number of different structures present. This concept fosters the selective logging only of the more fertile core. Drillholes are also variably fertile, depending on their orientational relationship to the structures in the host rocks. Structural parameters are either vectorial or non-vectorial. Vectorial structures parameters comprise normal structural orientations plus polar vectors like vergence, younging, shear sense and so on. They can be determined by one of two solution types: external solutions, which use an external reference structure to fix the drillcore and thus permit orientation of all structures within that core, and internal solutions, which use orientational data from a selected structure at three or more different drillhole orientation to determine the unique orientation of that structure, without reference to any external structure. Both solution types rely on constant orientations (orientational stability) of the selected structure, but the internal solution actually provides its own test of orientational stability. External solutions are the norm in outcropping situations and internal solutions are invaluable in blind situations. In blind situations sequential "internal then external" solutions can be used respectively to provide a reference structure and then use this for subsequent external solutions at individual points downhole. Blind prospects can now be drilled and interpreted as easily as outcropping prospects. Each solution type has its own optimum requirements. External solutions are ambiguous for certain orientational relationships between the drillhole and the reference structure (for example, a perpendicular relationship), hence drillholes in which external solutions are planned should be designed to avoid these orientations. Internal solutions are ambiguous for straight drill paths, and are most unambiguously resolved when the drill path attains maximum drillhole dimensionality, that is, it occupies a wide variety of orientations in 3D space; hence drillholes in which internal solutions are planned should be designed as combinations of non-parallel holes or as individual strongly curved holes. For both solution types an understanding of the kind of structural fertility required leads to intelligent design of drill paths, which is termed structural drill targeting. It is distinct from spatial drill targeting, which is the process which defines and (x,y,z) point-or volume-target. Effective design of drilling programs requires both structural and spatial targeting. The external and internal solutions for vectorial parameters are implemented via (1) visual (qualitative), (2) stereographic, or (3) core orienting frame procedures. Each of these has its own advantages. Stereographic procedures have been simplified via the erection of a drillcore reference frame in which three fundamental angles are defined, and the formulation of an all-inclusive set of stereographic recipes for determining orientations from the measurement of these angles. Non- vectorial structural parameters comprise an ad hoc array of useful measures which are simply described by numbers. Examples are angles between structures, and density of structures. Such parameters (some of which provide useful vectors toward ore bodies) are invaluable in drillcore because they can be measured and recorded rapidly, without determining the orientation of the core. In a summary, non-oriented drillcore can now be structurally mapped exactly as if it were outcrop. Interpretation of the significant volume of unique structural information which is beginning to flow from this system can be optimised by using, in addition to the conventional cross section and longditudinal section, three new modes of presentation. The natural cross section is that section in space normal to a principal structure of interest. It is a section in which it is advisable to drill to obtain certain structural information, and in which the results need to be presented. A newly defined unique cross sectional orientational symbol is recommended for dramatic improvement in the quality of information presented in cross sections. Stacked level maps are a powerful adjunct to cross sections.

Jan 1, 1990

On the basis of field observation, four principal styles of hydraulic breccia are recognised, and their characteristic features noted. In practice, hybrid styles are most commonly encountered. Numerous examples will be illustrated during the oral presentation, and the potential for definition of a formative environment is emphasised. In one example presented, it is suggested that more than 50 episodes of hydraulic fracturing can be recognised. In all cases at least sane useful conclusions can be drawn in the context of modeling for drill targets.

Jan 1, 1987

By I Thin, L Morizzi, C Seymour, G Mungur

Olympic Dam has been investigating mine design options for the South Mine Area (SMA), which will continue using the existing sublevel open stoping (SLOS) method. The SMA is an undeveloped mining area, located south of the existing underground mining areas currently in production at Olympic Dam. The SMA study reached the stage where geotechnical inputs were required for stope design, infrastructure location and ground support forecasts. A large database of geotechnical data was collected to inform open pit designs for the ODX (Olympic Dam expansion) project (resulting from 659 drill holes). This geotechnical data has since been reprocessed to align with design inputs required for the SLOS mining method. The result has been the construction of a preliminary three-dimensional mining rock mass model (MRMM) that has been incorporated into preliminary stope mine design and infrastructure layout assessments, which have taken into account the predicted prevailing ground conditions.As with any model, it is necessary to improve the confidence in its predictability; therefore the model must be calibrated. The preliminary SMA MRMM was no exception. First pass calibration was possible with results from underground geotechnical window mapping from exposed rock mass conditions in the lateral development and surface geotechnical holes for ventilation shafts.The SMA project continues to advance and has started a program of resource drilling. Selected holes have been identified that target data limited areas. This will ensure that the data gaps are infilled in order to maintain the required data density required to improve the model confidence. In addition, further underground window mapping in the SMA will provide ‘mine scale drill hole’ data that can be used to either update the MRMM or as part of planned future calibration. Stope performance data from stopes will provide further valuable data for calibration purposes.The proposed paper will present the process and findings that have been followed in order to establish a well calibrated geotechnical model that can be used with an acceptable level of confidence in the ongoing refinements of the mine design and planning process for the SMA.CITATION:Thin, I, Morizzi, L, Mungur, G and Seymour, C, 2016. Building and calibration of a geotechnical model for sublevel open stope design at Olympic Dam, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 523–532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By P G. Self, M D. Raven, R A. Eggleton

Investigation of an abandoned quarry near Rowland Flat in South Australia identified asbestiform antigorite as the fibrous serpentine mineral mined during the 1940s to 1978 for filler applications, not amphibole asbestos or chrysotile as reported in earlier investigations. Scanning and transmission electron microscopy (SEM and TEM) and selected area electron diffraction (SAED) of individual fibres were used to confirm the identification. Chrysotile is widely regarded as the only asbestos mineral in the serpentine group. Further work was done therefore, on the geology and mineralogy of the occurrence, and the health implications were reviewed. A zone of antigorite alteration, with associated talc, is traceable for 750 m along strike of recrystallised dolomitic siltstone within Woolshed Flat Shale of Neoproterozoic age. The antigorite formed, in part, by replacement of prismatic crystals of probable tremolitic amphibole. The deposit is proximal to the Williamstown Fault and the serpentine-talc alteration is possibly due to fluids expelled along the fault during late-stage deformation in the Early Palaeozoic Delamerian Orogeny. The antigorite comprises white to pale green bundles of lath-shaped fibres that occur either as randomly- arranged equant patches after amphibole or as cross-fibre veins, both intimately mixed with calcite. Highly fibrous product was mined from the weathered zone where calcite was leached during weathering. Gentle grinding releases fibres with a high aspect ratio (>10:1) that show a wide range of fibre thickness, including a significant proportion of fibres <0.25 ¦m width. Toxicological studies on fibrous antigorite from Poland and Italy indicate that the carcinogenic potential of this form of serpentine is similar to amphibole asbestos. X-ray diffraction (XRD) and fourier-transform infrared (FTIR) techniques readily distinguish antigorite from chrysotile. Determination of asbestiform habit and confirmation of antigorite mineralogy is most reliably done using electron microscopy, preferably with SAED capability.

Jan 1, 2008

The Fraser Range is composed dominantly of basic pyroxene granulites derived from basalts, many of which appear to have been vesicular and pillowed. Acidic and basic garnet-bearing granulites are important in the west, and acidic granulites and narrow anorthosite layers are dominant in some regions east of the Fraser Range. An extensive flat-lying olivine gabbro sheet cuts the granulites, and in places has been converted to spineI-bearingmeta-gabbros and pyroxene granulites. The granulites of the Fraser Range (Proterozoic) are separated from the gneisses and schists of the goldfields regions (Archaean) by the Fraser Fault, over which there is a large gravity anomaly (gradient 20 milligals per mile). Some of the problems associated with the concentration of Cu, and Ni liberated from mineral lattices during metamorphism, and other principles of metal concentration in granulite terranes, are discussed. The recognition of vesicular and pillowed zones, even though highly metamorphosed, is of fundamental importance.

Jan 1, 1969

The Bulli Seam, New South Wales, comprises medium to low volatile bituminous coal, generally of coking quality. It is worked over an area embracing 300 square miles.Variations in several factors are found.1. The seam is somewhat disturbed and dissected by various structural features.2. This structure, and present topography, have resulted in depths of cover from very shallow to approaching 2,000 ft in the presently worked areas.3. Wide variations of seam thickness occur.4. Gradations of rank occur from place to place.5. Variations in seam gas content and wide variations in seam gas composition are experienced.6. Variations in coal strength occur.These factors may contribute to the occurrence of stress and gas phenomena in mining exploitation.INTRODUCTIONThe Bulli Seam, the most extensively worked seam in Australia, is the uppermost seam of the Illawarra Coal Measures, which comprise the southern portion of the Sydney Coal Basin. Generally, the rank of the seam and its assemblage of types make it ideal for the production of hard metallurgical coke. The thickness and relatively flat dips render the seam suited to mechanized bord and pillar mining, and this method is used almost without exception. At the north-eastern corner of the field, stress and gas phenomena have occurred during mining.Various data have been assembled on physical, chemical and geological conditions of the seam which may influence the occurrence of stress and gas phenomena. This material is presented in an attempt to explain the location of such phenomena to date, and to enable variations in conditions to be considered when future possibilities are being assessed.

Jan 1, 1963

By X Yang, B Wang, L Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Huoqiu iron ore field in north-west Anhui province is located in the south-east margin of the North China Craton and hosts large iron resources. Orebodies are hosted in Neoarchean amphibolite facies metamorphic rocks, forming silicon-iron bands from north to south. The area is dominated by an Early Precambrian basement consisting of Neoarchean grey gneisses, amphibolites and metasediments. The gneisses are similar with assemblages of Trondhjemite-Tonalite-Granodiorite in compositions and intercalated with amphibolites. Igneous zircons from gneisses and amphibolites have U-Pb ages of 2.86 and 2.75 Ga respectively, which are interpreted as the crystallisation ages of their protolith. Zircons from amphibolite and gneiss have eHf(t) values of 2.4–15.5 and -3.0–1.5 respectively. The tDM2(Hf) model ages of the gneiss range from 2.87 to 3.14 Ga, which is consistent with tDM1(Hf) ages of amphibolite (2.84–3.16 Ga). The U-Pb-Hf isotopes thus confirm that the gneisses were generated by partial melting of amphibolite. Two granites produce two group Hf isotopic compositions. The older one (1916 ± 42 Ma) has eHf(t) values and tDM1(Hf) ages of -9.4–3.4 and 2.24–2.71 Ga respectively, whereas the younger one (1823 ± 41 Ma) shows a large variation in eHf(t) values of -18.1–12.5 and tDM1(Hf) model ages of 1.73–2.92 Ga. Geological and geochemical characteristics indicate that the Huoqiu banded iron formations are a Superior-type iron formation rather than an Algoma-type as previously considered.CITATION:Yang, X, Liu, L and Wang, B, 2015. Study on the Huoqiu banded iron formation, West Anhui Province, East China , in Proceedings PACRIM 2015 Congress, pp 649–656 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The use of solid state detector and radioisotope x-ray source for x-ray fluorescence analysis is illustrated by analysis for iron, copper, zinc, tin, and lead in about 700 samples taken from Australian mineral process streams. Limits of detection based on counting statistics (3 standard deviations) range from 0·001 to 0·004 per cent by weight element. The analysis accuracy was usualIy between 2 to 10 per cent (rms) of the mean element concentration and was determined by comparison with assays supplied by mineral companies. In most cases the main cause of error appears to be due to this assay and not the x-ray fluorescence technique.Some potential fields of application of solid state detector and radioisotope x-ray source for analyses in the mineral industry are indicated.

Jan 1, 1974

Plant for the production of sulphuric acid from pyrites flotation concentrates was commissioned at Cockle Creek during 1956, to meet increasing demands for commercial acid and superphosphate. Pyrite was chosen as raw material because of the uncertain supplyposition of imported brimstone and the desirability of utilising domestic sulphur.Desulphurisation of the pyrite is performed by two 40-ton per day roasters of the Turbulent Layer type operated under licence from the Badische Analin and Soda Fabrik (B.A.S.F.) organisation. These units are the first of their kind commissioned in the southernhemisphere. Pyrite is fed to the roasters in the as-received un-dried condition. Waste heat steam production is coupled with electricity generation within the plant. Sulphur dioxide is produced at comparatively high strengths and cleaned by conventional cyclone and hot electro-filter equipment.The acid unit has a capacity of 100 mono tons of sulphuric acid per day and includes cooling and wash towers, mist precipitators, a single stage drying tower, 4-pass oxidation section and absorption system.INTRODUCTIONSulphuric acid has been manufactured at Cockle Creek Works since 1913, when the first chamber nitration plant was commissioned. The raw material was brimstone roasted in Herreschoff furnaces. Since that time three additional chamber units have been constructed and have produced acid from brimstone, zinc concentrates, pyrites and -spent oxide, according to changing economic and supply factors.Three chamber units are still in operation. Contact processes have become increasingly important since the first Schroder-Grillo unit was commissioned in 1923. Six of these 5-ton per day units were operating in the mid-thirties, but have since been demolished. Two 15 ton Chemico hot gas contact units commenced operation in 1937 and 1938, and although modified, are still in service.The increasing demand over recent years for sulphuric...

Jan 1, 1957

By R J. Norris, D J. MacKenzie

Gold-bearing veins have formed at a wide range of depths throughout the uplift history of the Otago Schist. The earliest gold mineralisation occurred during the later stages of Mesozoic metamorphism. This mineralisation was characterised by diffuse wall rock alteration with greenschist facies metamorphic or retrograde metamorphic mineral assemblages, and gold occurs in this altered rock. Quartz veins formed in .steeply dipping extensional fractures associated with this mineralisation type strike north to northeast. The Macraes mine exploits this deposit type. The present northwest strike of the mineralised zone at Macraes is a result of post-mineralisation deformation of the schistosity-parallel mineralised shear zone which hosts northeast striking extensional veins. This combination of schistosity-parallel shear zone and steeply dipping northeast striking veins may exist elsewhere in Otago, and this deposit type is most prospective. Steeply dipping quartz veins formed during post-metamorphic un-roofing of the Otago Schist strike northwest to west and occur as clusters of near-parallel structures in east and central Otago. These veins consist mainly of massive quartz, although some prismatic quartz occurs also. Breccia fragments in veins are common and these are generally silicified, with some gold. Wall rock alteration is negligible, and vein margins are sharp. A set of middle Tertiary veins occurs in northwest Otago. Most of these also strike northwest and dip steeply, but some strike northeast. These veins contain abundant ankeritic carbonate as well as quartz. The carbonate pervades adjacent wall rock as veinlets, but gold mineralisation is confined to veins. Quartz is commonly prismatic and vuggy, and contains gold, which is commonly coarse grained especially in silicified breccia zones. Associated veins contain stibnite. This vein type formed close to the paleosurface (>2 km). Mineralised veins in Marlborough currently strike northwest, but these have been rotated from northeast strike during Alpine Fault displacement of Marlborough from Otago. Some of these veins were formed under late metamorphic conditions and are similar to the north to northeast striking veins in Otago. As in Otago, this type should be considered to be most prospective if they have associated schistosity-parallel shears.

Jan 1, 2000

The Hill 50 Gold Mine is situated at Boogardie, 3 miles on a bearing of 295 degrees from; Mount Magnet township. Mount Magnet lies 300 miles north-north-east of Perth, Western Australia (Fig. 1).The older workings of the mine may be identified with those of Sirdar, Gold Mining Lease 696M The Sirdar had been worked before 1902 though no records remain, and irom 1903 to 1912 about a thousana tons at a grade of 6' 2 dwt. was extracted annually; by the end of 1918 6,225 oz. of gold had been obtained from the milling of 17,852 tons of ore. In view of these yields, and the length and width of the lode, this mine was early recognized as one of the most promising in the district. From 1919 to 1924 the ground,including G.M.L. 1282M, was held as Mt. Zion G.M.L. 1183M.The Hill 50 Gold Mine N.L. company took up the workings as Hill 50 G.M.L. 1282M in 1934 and have continued operations to the date of writing. To the end of 1956 the Hill 50 Gold Mine had yielded 982,106 tons of ore for a return of 448,'602 fine oz. of gold.The mine has been described by: J utson (1915), Feldtmann (1920), Johnson (1949), and Finucane (1953). Finucane (1953) details the mine structure to a depth of 414 ft. The author was able to examine the mine to a depth of 1305 ft. Detailed main level mapping to the 1060 level and a detailed surface examination have revealed aspects of the structure which were previously obscure.

Jan 1, 1960

By B Orchard

New Zealand SteelÆs Waikato North Head mine, situated at the mouth of the Waikato River, supplies approximately 1.2 million tonnes per annum of titanomagnetite concentrate to the Glenbrook steel mill. The mine draws its fresh water supply from the Waikato River, abstracting approximately 38 000 cubic metres per day. During the concentration process of the ironsand, slimes are liberated into the plant wastewater. The plant wastewater, storm water and groundwater from the mining operation is treated and passed through settling ponds. Around 118 400 cubic metres per day of water are drawn from the recycle settling ponds for use in the concentration plant. Typically a daily average of up to 15 100 cubic metres of the treated water is discharged back to the Waikato River. Since the early 1990s significant improvements have been made to the water treatment at Waikato North Head mine and regularly the mine discharge water quality is similar or better than background river water quality.

Jan 1, 2002