Search Documents

By G. Couture

"The Glencore Raglan mine Concentrator, located in Quebec’s Nunavik region, has been in operation since 1997. The nickel metallurgical plant was originally designed to process 100 tonnes per hour of ore to produce 130 000 tonnes of nickel concentrate per year at 16% Ni. The increased grinding capacity and the discovery of rich ore bodies have increased the annual production to more than 190 000 tonnes of concentrate at 19% Ni. In 2014, the Metallurgical group, with support from BBA, implemented an expert control system on the flotation circuit. This project was initiated to cope with the high variability of the concentrator’s feed. Increasing the plant recovery and final concentrate grade were also important project objectives. The implementation of the expert system ensures better control of concentrate inventory while maintaining maximum plant throughput. This paper describes the successful implementation of the new control system, the control technology selection and the flotation circuit optimization. It will also discuss the performances obtained with this new approach and the improved process stability.IntroductionThe Raglan Mine is located in Northern Quebec along the 62th parallel. It has been in operation since 1997 and was originally designed to produce 130 000 tonnes of concentrate annually at 16% Ni. The increasing of the grinding capacity and the discovery of rich ore bodies have increased the annual production to more than 190 000 tonnes of concentrate between 18 and 20% Ni."

Jan 1, 2015

By D. G. Hulbert, J. H. Schubert, R. G. D. Henning

"Froth depth, along with reagent addition and aeration rate, is one of the crucial factors that can be used to control a flotation circuit. Sub-optimal setpoints and disruptions in levels have a severe adverse influence on grades and recoveries. A novel control strategy has been developed which provides exceptionally tight regulation of pulp levels. The controller observes and acts on all the flotation levels simultaneously. This provides a clear improvement over the standard approach, which is to use a set of Pl controllers. The system has been run on several industrial plants and has resulted in reduced fluctuations in level; fast responses to setpoint changes, and fast settling times after start-ups or disturbances. Testwork has shown that the improvements in level stabilisation translate into improvements in recovery and grades.IntroductionProcess control and optimization have an important influence on the economic efficiency of flotation plants. Inefficient operation can allow the wrong balance between grades and recoveries, and can also lead to adverse shifts in the grade-recovery relationship. Of all metallurgical operations, flotation loses the largest proportion of valuable material. Better operation can reduce these losses.An essential requirement of a good controller is that it should be able to stabilize and regulate the plant. Stable operation allows the performance of the plant to be observed without being obscured by the effects of disturbances and fluctuations. The optimum conditions can then be detected more easily. Good regulation can maintain operation at the optimum with proper neutralization of disturbances. Only when good stabilization and regulation are achieved can an optimizing strategy be properly applied.Froth depth, aeration rate and reagent addition are the three means by which a flotation plant is generally controlled. These control actions are effective on different time scales. Reagent addition is slower in its effect as some conditioning time is required. Since reagents are only added at the head of the circuit and at a few selected points within the banks, time is required for the effect of reagent changes to move through the circuit. Because of this slower time constant, reagent addition is more suited to process optimization and to dealing with slower changes in the process. An example of these slower changes is variation in the feed."

Jan 1, 1995

By Neil R. Burns, Michael Doggett

Abstract - The Nanisivik mine offers a unique opportunity to examine the economics of a mining scenario from its original feasibility study through to closure. In the early 1970s, the Strathcona Sound project (exploration around the Nanisivik mine) had advanced to the point where a significant mineralized body had been defined and a feasibility study was initiated. The study supported development of the Nanisivik mine, with government investment in regional infrastructure, and the mine was constructed and operated for 26 years. Many elements of the feasibility study were difficult to estimate because the project was unique in its high Arctic setting. As a result, many differences were found when comparing the actual mining data to the feasibility study. The majority of these differences were the result of an actual mine life of 26 years instead of the planned 12.5 years. Most of the mining costs were higher than estimated and production occurred at a much higher extraction rate than planned. On a constant dollar basis, the metal prices were, on average, below the feasibility estimates. For the most part, these differences balanced out, with the actual mining being only slightly more profitable than anticipated in the feasibility study.

Jan 1, 2004

A comprehensive axial test program has been undertaken at the WASM Dynamic Test Facility on the performance of 20mm threadbar. The threadbar tests had a double embedment configuration, with variation to the encapsulation lengths, debonded length and surface hardware and fixtures to examine failure mechanisms. Performance was significantly affected by the collar embedment length and type of fixture nut used. Results ranged from thread shearing occurring between the nut and bar at 1kJ of energy dissipated, to control plastic deformation of a central debonded length dissipating 22kJ.

May 1, 2009

By Alex Cormode, Carlos Perucca

"Sylvinite ore from the Saskatoon area typically contains about 5% insolubles, occurring as clays and carbonates. These insoluble slimes must be removed sufficiently well to permit an efficient subsequent potassium chloride flotation, due to their high adsorptive capacity for amines used as potash collectors. The insolubles are liberated from sylvinite by high attrition scrubbing in a slurry. The liberated slimes are separated by multistage cycloning or by a selective flocculation-flotation process.An outline of the potash processing operations at Agrium Vanscoy Potash Operations is given, emphasizing the insoluble slimes froth flotation separation process. This process was originally implemented at the Agrium plant in the mid- 1970's and replaced a hydrocyclone system.IntroductionAgrium Vanscoy Potash Operations is located 40 Km southwest of Saskatoon, almost midway between the communities of Vanscoy and Delisle. Processing operations started in 1969, and the annual production capability was subsequently increased to the current 1.8 MM tonnes per year of muriate of potash.The mining operation at Agrium Potash which was described in a paper by Jones and Pruggerl , is done underground using four large continuous double rotor boring machines for the main production with development done by heliminers. Annual ore production is 5.5 MM tonnedannum. Ore is hoisted 1,100 m to surface for processing."

Jan 1, 1999

By J. D. Nye, I. A. Farr, W. J. D. Stone

"A unique deposit of barite exists near Brookfield, Nova Scotia. The crystals are extremely fine and the whole deposit virtually free of heavy metals. The deposit size was not large enough for conventional uses, such as the production of barium carbonate and drilling mud. In an effort to obtain maximum utilization, a program was begun to determine if U.S.P.-grade pharmaceutical barium sulphate for X-ray diagnosis could be produced. Early work was sufficiently encouraging to institute a development program under the federal Program for Advancement of Industrial Technology. This has been very successfully completed. Canadian and U.S. process patents have been issued, clinical trials have been successful, a production plant has been designed and the plant’s production sold. The processing plant will include magnetic separation for the removal of iron minerals, fine grinding by paddle milling to minus one micron and acid leaching. The process is unique in that at no time is the barium taken into solution.Information is given on the deposit, process, markets, use, plant capital and operating costs, and projected profits. The initial production plant will have an annual capacity of 2,000 tons per year of end product. Capital cost is $850,000 and annual turnover more than $1.5 million. As this capacity only represents approximately 15% of the North American market, rapid plant expansion is foreseen."

Jan 1, 1980

By Serge Ouellet

Identification and quantification of cementitious phases in cemented paste backfill (CPB) is difficult due to the fineness of tailings and the low binder content used in the mixture. Techniques such as X-ray diffraction and thermogravimetry were ineffective (mainly due to tailing mineral interference) to identify and quantify hydration products in most works reported in the literature. On the other hand, scanning electron microscopy (SEM) was used in many cases but mainly for qualitative purposes. This paper presents the development of a new approach based on a computer program (SEM-XMAP) that combines X-ray dot mapping images acquired by SEM and generates a coloured image representing the mineralogy and the microstructure of a given CPB specimen. The technique is applied to one CPB sample mixed with blast furnace slag (BFS) and acidic sulphated mixing water sampled in a mine dewatering system. The technique allowed identifying calcic matrix, unhydrated and partially hydrated BFS particles, and sulphated phases.

May 1, 2007

By Tassos Grammatikopoulos, Sarah Prout, William Mercer, C. Gunning

"The Nechalacho rare metal deposit is located in NWT, Canada. Avalon Rare Metals Inc. is now evaluating processing techniques for recovery of REE to be used in the industry. QEMSCANTM analysis coupled with whole rock, REE, Zr and Nb, and electron microprobe analyses were utilized to identify and quantify the mineralogy of the deposit, and define the REE distribution among minerals. QEMSCANTM mineralogy was performed on fifty intact drill samples using EXPLOMINTM that provided textural information for the mineralization; crushed samples were used to determine the variability of the ore and define REE domains, and composite samples to determine the liberation and association of the REE minerals. The sample matrix predominantly consists of biotite, feldspars, quartz, muscovite/clays, minor chlorite and amphibole, magnetite and hematite and carbonates. REE include in decreasing order of abundance allanite (3.6%), monazite (1.5%), synchysite (0.9%), columbite (0.9%), fergusonite (0.6%), bastnaesite (0.4%), and zircon 11.0%. The majority of the HREE are carried by fergusonite and zircon, and the LREE by monazite, allanite, synchysite and bastnaesite. QEMSCANTM mineralogical data is extremely valuable in assessing the mineralogy of the ore. The data have been implemented in defining the mineralogy of the ore body, support metallurgical test work, predict recoveries and grades, and finally calculate reserves of the deposit.INTRODUCTIONAvalon is in the unique position of owning and developing one of the world’s largest rare earth deposits in the Northwest Territories of Canada.The term Rare Earth Elements (REE) is used to describe the 15 lanthanide elements or metals and, more recently, the metals yttrium and scandium, which display similar physical and chemical properties. REE are not particularly rare and have a similar abundance in the earth’s crust to nickel, tin or tungsten. Unlike these better known metals however, the rare earths have little tendency to become concentrated into commercial ore deposits. When they do become concentrated, deposits of REEs usually display enrichment in one of two groups. The most commonly occurring deposits of REEs contain a sub-group of elements referred to as the “light rare earth elements” (LREEs), which include lanthanum, cerium, praseodymium, neodymium, and samarium. Less commonly, deposits of REEs contain the much more valuable sub-group of elements referred to as the “heavy rare earth elements” (HREEs), which include europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium and lutetium. Yttrium and scandium most commonly occur in association with this second HREE sub-group. Generally, LREEs are produced from the mineral bastnaesite, and the HREEs have been produced from the minerals xenotime and monazite. LREEs continue to be produced from bastnaesite, however in the 1980s, China started production of HREEs from unique laterite clay deposits. China now produces approximately 95% of the world’s rare earths."

Jan 1, 2011

By D. Turk, P. Lefebvre, J. Sargent, K. Major

"Stillwater Mining Company recovers platinum and palladium from their Nye Montana operations. Mining first commenced at Nye in 1987 at a milling rate of 455 t/d (500 stpd). The plant was expanded in 1995 with the replacement of the ball mill and the addition of flotation capacity to increase mill throughput to 1820 t/d (2000 stpd). The applications for platinum and palladium have increased in recent years particularly in the automotive industry and the supply of the metals has remained fairly constant with prices for both platinum and palladium increasing and remaining very stable. In 1997 Stillwater initiated the expansion of their operations to increase production of platinum and palladium. Projects were initiated to expand production at the Nye operations, increase smelter and refining capacities at the Columbus facilities and to develop the extension of the orebody at the East Boulder site. This paper will discuss the changes at the Nye concentrator which were completed to increase production from 1820 t/d (2000 stpd) to 2730 t/d (3000 stpd) and eliminate some of the process bottlenecks.IntroductionStillwater Mining Company is mining the only significant primary source of PGMs outside of South Africa. The J-M Reef is an extensive mineralized zone containing PGMs that has been traced over a strike length of about 43 km (27 miles) in the southwest region of Montana. Stillwater controls the entire PGM mineralized zone.Johns-Manville geologists discovered palladium and platinum in the early 1970’s. In 1979, a Manville subsidiary entered into a partnership with Chevron, USA to develop the project. In 1 987, operations at the Stillwater property near Nye, Montana commenced."

Jan 1, 2000

? CONSTRUCTION AND MINING COSTS ARE HIGH IN THE ARCTIC ? VERTICAL KIMBERLITE PIPES WITH HIGH STRIP RATIOS ? SITE SPECIFIC GEOMETRIC CONSTRAINTS ? OPEN PIT FOLLOWED BY UNDERGROUND MINING ? HIGH KIMBERLITE UNIT COSTS TRACK INSTALLED ON PIT WALL ? INTENDED TO REPLACE MAIN HAUL RAMP ? 5 MIN HOIST CYCLE TIME ? KEY ADVANTAGES - REDUCED CYCLE AND STRIPPING RATIO ? TECHNOLOGY EXISTS IN OTHER APPLICATIONS

May 1, 2003

By C. Gosselin, G. M. Payenzo, C. Bazin, M. Desnoyers, G. Chevalier

"ArcelorMittal Mines Canada operates hydraulic classifiers to reduce the silica content of an iron oxide concentrate from 4.5% to less than 1.2% SiO2. Sampling campaigns were conducted to develop a preliminary model for the hydraulic classifier. Results show that iron oxide and quartz are respectively concentrated in the coarse and fine size fractions of the classifier feed. The mineral partition curves in the classifier and the size distribution of the minerals in the feed are used to simulate the classifier operation in order to identify the source of variability observed in the daily plant production data. Results indicate that most of the variation is probably caused by unsteady operating conditions of the classifiers.INTRODUCTION Hydraulic classifiers are a class of gravity separation devices (Wills, 1992) used to classify particles according to their size and specific gravity. Hydraulic classifiers also known as density separators (Hearn, 2002) combine hindered settling and upward flow of water to selectively entrain light particles to an overflow stream. Denser particles settle to an underflow stream. Hydraulic classifiers are used for various purposes ranging from cleaning of coal (Das, Sarkar, & Mehrotra, 2009), recovery of chromite from plant tailings (Kumar, Tripathy, & Rao, 2009) to upgrading iron oxide concentrate (Hearn, 2002). ArcelorMittal Mines Canada operates several hydraulic classifiers to upgrade an iron oxide concentrate by removing fine quartz and other light minerals from hematite that is the main iron oxide mineral. A project was initiated to analyze the operation of the classifier in an attempt to identify the source of the variability in the production results and to assess the potential of increasing iron recovery in the classifier. One possible disturbance for the classifier operation is the change in the classifier feed composition and size distribution, while the other considered disturbance is the operation of the classifier. The paper is divided into five sections. The first section summarizes the ore processing sequence for the production of iron oxide pellets to identify the position of the hydraulic classifier in the process. The second section describes the hydraulic classifier. The third section discusses the sampling campaigns conducted on the hydraulic classifier. The method used to process the data from sampling, the results of the data processing and simulation of the classifier are discussed in the remaining sections."

Jan 1, 2012

By Jan E. Nesset, James A. Finch, Wei Zhang

"Bubbles are unquestionably the heart of the flotation process. Their size and combined surface area are largely what drive the recovery process. This suggests that plant engineers should be aware of where their plants are operating with respect to what is achievable for these key parameters. The paper presents a model of how the key operating variables of frother type and concentration, gas rate, altitude (above sea level) and viscosity affect the Sauter mean bubble size (D32) and bubble surface area flux (Sb). The results are compared to a set of plant measurements that demonstrate the benchmarking capability of the approach. A case study is used to link hydrodynamic change to improved metallurgical performance.INTRODUCTION At the beginning of the 20th Century the early practitioners of flotation were aware of the importance of understanding bubble behaviour (Rickard, 1916) but measurement of individual bubble and gas behaviour in the industrial environment was not possible due to a lack of adequate sensors. This situation was not rectified until three quarters of a century later with the advent of industrially-robust sensors developed, notably, at the University of Queensland’s Julius Kruttschnitt Mineral Research Centre (JKMRC) (Schwarz & Alexander, 2006) and McGill University (Gomez & Finch, 2002). What emerged was not the chaotic environment perhaps expected, but defined relationships between gas rate, gas holdup, bubble size and the total surface area of bubbles. These relationships could be defined by mathematical expressions and predicted from an understanding of the key process variables (Gorain, Franzidis & Manlapig, 1997; 1999) (Hernandez-Aguilar, Gomez & Finch, 2002) (Gomez, Cortes-Lopez & Finch, 2003) (Nesset, Gomez & Finch, 2007). The early JKMRC work focused on a large pilot cell (3 m3) installed in plant environments, while the McGill work was initiated on flotation columns (Finch & Dobby, 1990) (Xu, Finch & Uribe-Sales, 1991) and later adapted to industrial mechanical cells (Cooper, Scott, Dahlke, Finch & Gomez, 2004) (Dahlke, Gomez & Finch, 2005) (Nesset, Gomez, Finch, Hernandez-Aguilar & Difeo, 2005). Yianatos of Santa Maria University (Chile), a graduate of the McGill research team, carried the work to industrial settings in South and Central America (Yianatos, Bergh, Condori & Aguilera, 2001). The methods of gas dispersion measurement are now well accepted and most major research centres and flotation cell manufacturers have adopted the technology (Pyecha, Sim, Lacouture, Hope & Stradling, 2006) (Yañez et al., 2009) (Collins, Schwarz & Alexander, 2009)."

Jan 1, 2012

By David G. Almond

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations having large SAG mills fitted with variable speed drives. Problems associated with effective operation of this equipment has created the need for better operator knowledge of mill load behavior and the need for new instrumentation capable of providing accurate information about load movement and composition. This paper discusses two performance enhancing instruments available to address these needs.INTRODUCTIONThe economic demands of new mining projects has resulted in increased equipment sizes and this is particularly evident in milling where there are now many SAG mills operating in the range of 28’ – 40’ diameter with installed powers of 8 – 22 MW. These mills are designed to process very high capacities of ore daily2 and the variable characteristics of many of the deposits mined results in the need to vary the mill speed during processing to cater for the changes in ore hardness. Mill speed changes often result in operational problems associated with high-energy impacts striking the mill liners reducing energy efficiency as well as degrading the grinding media through breakage, accelerating liner wear and in extreme cases even breaking liners. These operational problems have given rise to the need to have instruments aimed at providing operators with accurate information in real time about the load composition and movement within SAG mills.The original concepts for operating SAG mills were derived from past experience of operation of conventional fixed speed ball mills. However, the relatively stable conditions that applies with fixed speed and constant ball charge in ball mills supports theoretical approaches to the grinding process based on energy calculations such as Bond’s Work Index concept. Later a set of parameters Si and Bij were used for describing load kinetics, but all of these methods neglect the details of load movement and how the energy is actually used inside of the mill. It is now commonly accepted as a basic rule that SAG mills grind by impact whilst ball mills grind by attrition and consequently SAG mills are designed and operated to generate a large amount of impacts by the cataracting load without paying sufficient attention to where these impacts are actually occurring. Many mills are operated on the basis that as long as the mill is consuming the expected power there is little attention given to the class of bodies using this energy and this often results in the inefficient use of energy."

Jan 1, 2005

By C. G. Bruce

"ON NOVEMBER 15th, 1950, the Department of Mines and Technical Surveys announced the discovery of vermiculite near Perth, Ontario. The announcement followed nearly a month of study to determine so far as possible the potentialities of the deposit and quality of the material from surface indications. The mineral was identified by the writer in the field among samples submitted by Mr. Arthur Powers of Stanleyville or, September 22nd, 1950. Within a week of the announcement, mining rights to properties covering a major portion of the deposit had been acquired by commercial interests.Hitherto, Canada has had to import her entire requirements of vermiculite. Prospects of .a domestic supply gave promise of considerable benefit to many industries, particularly the building industry, and to the consumer public. Should the deposit •prove large enough there was also the possibility of exporting to centres in the United States.Field and laboratory studies were continued at the Mines Branch during the winter of 1950-51 as opportunity occurred. It is the purpose of this paper to describe the results of these •preliminary investigations, to attempt to present the Stanleyville occurrence in its proper perspective with regard to similar occurrences elsewhere, and to review the salient features of the vermiculite industry.Properties and UsesVermiculite is a hydrated magnesium aluminum silicate. In appearance it resembles mica, having the same micaceous cleavage, but it differs from that mineral in being very soft, pliable, and inelastic. Colours range from black through dark olive-green and brown to almost colourless."

Jan 1, 1952

By G. G. Eichholz

SUMMARY RADIOACTIVE dynamite has been prepared by introducing a small amount of antimony-124 into the explosive. Test work is described on the effectiveness of this tracer, on radiation levels in its neighbourhood, and on different methods of .application. Factors determining the choice of isotope, amount of activity, and overall cost of this process are discussed. INTRODUCTION Instances are known in which dynamite remains unexploded in drill holes in mining operations. Usually such 'bootlegs' are easily located by inspection of the face and the powder is removed before subsequent drilling is started. Occasionally, however, serious accidents occur because workmen drill into an undetected piece of dynamite. In order to avoid such accidents it was suggested that a different method of location might be tied, such as that afforded by the use of radioactive tracers. This paper describes some experiments that were carried out under the auspices of the Department of Mines and Technical Surveys, with the active co-operation of Canadian Industries Ltd. and Canadian Refractories Ltd., to test the feasibility of such a scheme.

Jan 1, 1957

By Thomas Deschamps

The main objective of this work was to investigate the effect of binder addition on the geochemical properties of surface paste tailings. Nine leaching columns were prepared following different disposal configurations: non-cemented, non-cemented with cemented layers, and cemented .The proportions of cement by total paste weight were between 0 and 1% for a whole column; the maximum amount of cement in a single layer was 2%. The material used was a sulphide-rich tailings coming from a Canadian hard rock polymetallic mine. The columns have been flushed once a week during 30 weeks. The recovered leachates were analyzed for pH, Eh, conductivity, and a wide range of elements. The drainage rates were monitored during the initial disposal as well as after each column flush. The results show that binder addition can improve the whole environmental performances for some of the studied disposal configurations. The disposal configuration consisting of intercalation of three 2% cement paste layers within non-cemented layers (0.66 wt.% of cement for the whole column), and the configuration with 2% cement added only in the two bottom layers (0,44 wt.% of cement for the whole column), showed the best results in terms of water quality and drainage rates.

May 1, 2007

By K. G. Thorne, D. R. Lentz, A. F. Park

"The Main zone of the Clarence Stream gold deposit is hosted by a shear zone adjacent to the Saint George batholith in southwestern New Brunswick. The mineralization history relates to progressive deformation in the shear zone and the intrusion of the Magaguadavic granodiorite.Of three phases of deformation that have affected the area (D1-D3), D1 is not observed in the Clarence Stream shear zone. Two suites of igneous rocks intrude the shear zone: post-D2, pre-D3 gabbro; and granitic dikes, which crosscut the gabbros. Granitic dikes show a diverse range of relationships to D3 features, from pre-syn-D3 mylonitic fabrics in transposed and highly deformed enclaves, to nondeformed and entirely discordant dikes (post-D3).A variety of veins occur within this shear zone. Zoisite-bearing and later, crosscutting epidote-bearing veins are preserved as relics in quartz-mylonites, and predate quartz veins that host gold mineralization. The epidote-bearing veins are associated with pseudotachylitic cataclasite dikes, consistent with transient brittle failure during ductile deformation.Deformation relates to right-lateral strike-slip motion across the shear zone, and subhorizontal and near-vertical stretching lineations imply transpression. A late (late- or post-D3) dip-slip phase of motion is also apparent, and cooling followed a metamorphic peak early in D2-D3 history. Deformation of the shear zone, and more localized transient brittle failure, provided the permeability for fluid movement and vein emplacement. This scenario is similar to the findings of other studies, in which geochemical, tracer isotopic, and age-dating (U/Pb, 40Ar/39Ar) results suggest that the adjacent Magaguadavic granodiorite provided heat and metals. La zone principale (Main zone) du gisement d’or de Clarence Stream est encaissée par une zone de cisaillement qui longe le batholite de Saint George dans le sud-ouest du Nouveau Brunswick. L’historique de la mise en place de la minéralisation accorde un rôle important à la déformation progressive dans la zone de cisaillement et à la mise en place de la granodiorite de Magaguadavic.Des trois phases de déformation à avoir affecté la région (D1-D3), les effets de D1 ne sont pas observés dans la zone de cisaillement de Clarence Stream. Deux suites de roches ignées se sont mises en place dans cette zone de cisaillement : un gabbro post D2, pré-D3 et des dykes granitiques qui recoupent le gabbro. Les dykes granitiques montrent une grande diversité de relations avec les structures D3, allant de précoces à synchrones aux fabriques mylonitiques D3 dans des enclaves transportées et fortement déformées à des dykes complètement discordants et non déformés (post-D3).On note diverses veines dans cette zone de cisaillement. Des veines contenant de la zoisite ainsi que des veines d’épidote sécantes plus tardives, lesquelles sont préservées comme reliquats dans les mylonites à quartz et sont plus vieilles que les veines de quartz contenant la minéralisation aurifère. Les veines d’épidote sont associées à des dykes de catacalasite à texture de pseudotachylite, compatibles avec une rupture cassante épisodique durant la déformation ductile.La déformation résulte d’un mouvement décrochant dextre le long de la zone de cisaillement et les linéations d’étirement subhorizontales et quasi-verticales impliquent de la transpression. Une phase tardive (tardi- ou post-D3) de mouvement selon le pendage est aussi apparente, et le refroidissement succède à un pic métamorphique tôt dans l’histoire D2-D3. La déformation de la zone de cisaillement et la rupture cassante épisodique ont fourni la perméabilité nécessaire au mouvement des fluides et à la mise en place des veines. Ce scénario est similaire à celui proposé par d’autres études, dans lesquelles les résultats de géochimie, de traceurs isotopiques et de géochronologie (U/Pb, 40Ar/39Ar) suggèrent que la granodiorite de Magaguadavic avoisinante a fourni la chaleur et les métaux."

Jan 1, 2008

By Tony Robles

"A new process is disclosed for the recovery of gold and/or silver values from activated carbon wherein they are adsorbed as cyanide complexes. A unique chemistry allows the new process to use mill process water containing an inexpensive, non-hazardous compound as the eluant. The new process has an elution period of 5 hours at 98°C. The gold in the eluant can be recovered by electrowinning or zinc precipitation. The new elution process is simple, reliable, and provides an eluted carbon that may not require thermal regeneration before reuse. Retrofitting the new process to existing processes such as Zadra, Anglo, and others will not require significant capital expenditures.IntroductionThe efficient and reliable elution process for gold/silver from activated carbon is a very important process in the gold mining industry. The most common techniques for elution of gold cyanide from activated carbon are the Zadra and Anglo procedures.Specialized elution techniques like the Micron and Acetonitrile processes have not been commercialized to significant extent probably due to relatively complex unit operations and expensive reagents.Important functions of the gold recovery circuit are:Efficiently recover gold/silver from the loaded carbon.Carbon is in good condition for reuse for optimum recovery.The pregnant solution is amenable to electrowinning or zinc precipitation to recover gold/silver from the solution.The whole process to be simple and short to reduce gold inventories.Present Elution ProcessesTable 1 shows some carbon elution processes that are available today. The two main elution processes used in the industry are: (1) the Zadra process, in which hot cyanide solution is circulated through an elution column and electrowinning cells; and (2) the Anglo American Research Laboratory (Anglo) process, consisting of a pretreatment step with caustic cyanide solution, followed by elution with deionized water."

Jan 1, 2000

By Osvaldo A. Bascur, Curt Heftier

The lack of integrated information including the Energy/Utility Suppliers with sufficient detail for analysis causes inefficient operation in metallurgical complexes including the Energy/Utility Suppliers . Defining the right context for information use is essential for sustainable operations. This being said, what are we doing to enable people to act upon information and to be aligned to optimize the use of resources like raw materials, energy, water and consumables for an entire metallurgical complex? Collaboration between all company entities is a key component of improving efficiency. Evolution of web technology and object modeling of enterprise assets enables collaboration across the whole business. Operational troubleshooting occurs more quickly as the organization acts on issues to reduce wasteful operation. This paper presents a real time software infrastructure with tools that give users the ability to sift through available data, transform data into information for business continuous improvement and optimization. We will introduce a new technology for analyzing real time data, information and events using multidimensional analysis of information to detect anomalies based on the statistics of the data classified by time events to reduce the information into action. A new paradigm for collaboration at a local and strategic level is proposed to enable the enterprise to become proactive in dealing with wasted time and products. Three examples from the industry will presented and their benefits highlighted.

Jan 1, 2011

"Air Products approached LAC Minerals in 1987 to initiate trials with pure oxygen in the leach circuit at several LAC facilities in Canada. This paper gives an overview of oxygen use and covers specific operating data from the Doyon and Terrains Aurifères mills near Val D'Or in northwestern Quebec. LAC also uses oxygen at the Macassa mill in Kirkland Lake, Ontario.In addition to the LAC facilities, oxygen is currently in use for test purposes at the Holt McDermott mine in Kirkland Lake, Ontario and the Camflo mine near Val D'Or.There are two requirements for oxygen in the cyanide leach mill. Firstly, oxygen is required in the familiar gold dissolution reaction as follows:(1) 4 AU (s) + 8 NaCN (aq) + 02 (aq)+ 2H 20(aq) - 4NaAu(CN) 2(aq)+ 4Na OH(aq)Of the reagents on the left side of the equation, the availability of gold is fixed by the ore in question. Obviously, water is available in excess, 1eaving cyanide and oxygen as the limiting constituents in the process. Most mills operate with an excess of cyanide, which is fairly closely monitored. Dissolved oxygen levels, however, are not normally watched very closely and find their own level based on the temperature, the availability of compressed air and the ability of the ore to consume oxygen.Typical D.O. levels are in the 3-8 ppm range, however levels less than 1 ppm are not uncommon for refractory ores.With pure oxygen, dissolved oxygen levels as high as 30 ppm can be achieved. (Figure #1). This greatly accelerates the kinetics of the leach reaction and may also shift the reaction further towards completion thus increasing gold dissolution slightly."

Jan 1, 1990