Search Documents

By J. W. Meier

Introduction The great importance of air warfare during World War II and the introduction of large-scale air transportation and airborne operations created an immediate demand for large quantities of high quality light alloy products. Before this war, the use of magnesium, the lightest structural metal, was barely in the development stage, and considerable research work was needed to overcome difficulties in improving its properties and to attain uniform quality in mass production of magnesium alloy products. The Canadian Bureau of Mines was frequently called upon, by various agencies of the Armed Forces and of the newly established war industries, to examine magnesium alloys that had failed in fabrication or in actual service, and to advise on proper alloys and fabrication methods to be used. Failures in magnesium alloy castings were connected mainly with lack of knowledge of proper founding and surface-protecting techniques. Most of the defects were due to microporosity and faulty heat treatment. To aid the foundry industry, small-scale investigations were started on the effect of various factors in the casting technique in order to improve the quality of the products. These investigations were made in co-operation with representatives of the Armed Forces and the Canadian magnesium industry. This work was later co-ordinated into a broad research programme on magnesium alloys, comprising problems on melting, refining, various casting methods, heat treatment, and testing of properties of standard and special alloys. This research programme? is still in force, and the present paper contains some results of the first series of investigations on magnesium casting alloys carried out at the Experimental Foundry of the Bureau of Mines.

Jan 1, 1948

By P. Cleyle, K. McDermott, M. Hall, C. A. Harris

"This paper describes the implementation of an expert system for monitoring and control of the NO. 4 autogeneous mill and spiral circuits at Wabush Mines.This process control system incorporated the mill operating expertize of Wabush Mines operating personnel and was implemented to improve spiral iron recovery and mill productivity by:1. Continuously monitoring the mill power draw and ensuring that the mill feedrate is regulated to prevent damage to the mill motor, while simultaneously maintaining the feedrate at or as close as possible to the maximum feedrate determined by the process supervisor.2. Improving control over the spiral density and feed rate.3. Improving control over both tbe rougher and cleaner wash water.4. Reducing the frequency with which pumps are plugged.5. Allowing modifications to be made easily and quickly to test various operating strategies.This system was installed using COMDALE/C, a real-time Expert System for Process Control. It was readily accepted by the process operators and produces higher production performance in comparison to the other 5 parallel mill lines at a lower power draw."

Jan 1, 1992

By A. Gronningsater

Introduction As is well known, the fight between the blast furnace and the reverberatory furnace in copper smelting during the second decade of the century ended with a victory for the latter, a result which must largely be attributed to the introduction of flotation methods. To my knowledge, no new blast furnace has been blown-in at any American copper smelter since the War. As the metallurgy of nickel, up to and including matte smelting, is generally considered a close parallel to that of copper, the introduction of reverberatory smelting in the big new smelter of the International Nickel Company at Copper Cliff, built in 1928-30, seemed a logical adherence to a well established trend. In view of these facts, considerable comment was made when Falconbridge Nickel Mines decided to retain the blast furnace in their smelter built about the same time, in 1929. A presentation of the reasons governing this choice should therefore be of interest. The basic principles underlying the Falconbridge practice, and the considerations guiding the successive steps in the operations, will be discussed in the following. To understand the problems involved, the character and mode of occurrence of Sudbury ore must be kept in mind. Large amounts of disseminated ore are generally present. Although the gangue usually runs only about 50 per cent Si02, the ore hoisted as a rule contains more silica than needed in the smelting operation; until recently this excess was removed entirely by hand picking (in later years supplemented by magnetic sorting methods), a difficult and not very satisfactory method, in which 'the border line between ore and waste is entirely arbitrary, and therefore too much depends on the judgment of the picker.

Jan 1, 1934

By Michel Jébrak, Claude Bellehumeur

Abstract - Regional and orientation geochemical stream sediment surveys were carried out by the Quebec Department of Energy and Resources in southwestern Quebec, over a part of the Mont­ Laurier Terrane of the Grenville Province. The area contains some small stratiform zinc deposits. The response of Zn mineralization to geochemical surveys is weak; the known mineralization is not defined by anomalous samples and consistent patterns. This study uses a technique that increases the geochemical signature of Zn mineralization in filtering out geochemical background components related to lithologies and surficial conditions. The background variations were modelled using principal component analysis, and the filtering technique consists of the partial reconstruction of the data matrix from results of principal component analysis . The filtering procedure considerably enhances the Zn anomalies located in the catchment basins of Zn deposits, and defines some new anomalies in proximity to the marbles of the Mont-Laurier Terrane, the principal metallotect of Zn mineralization.

Jan 1, 1993

Agenda ?Trends in Wireless Technology ?Success and Opportunities ?Improving plants efficiency ?Improving plants reliability ?Improving plants safety and security ?Wireless Ecosystem ?Lessons Learnt / Recommendations Why Wireless? ?Lower cost (no wiring cost) ?Flexibility (no wire) ?Standards-compliant wireless devices major factor enabling growth:?Standard WLAN (IEEE 802.11)?Wireless field I/Os (IEEE 802.11, ISA100.11 and WirelessHART) ??Wireless adoption will become a milestone that will rival the introduction of Fieldbus and the distributed control system (DCS) in its importance.? ARC Advisory Group

May 1, 2009

By George C. Bateman

WHAT I would like to do is to talk for a while tonight about the Canadian mining industry in wartime-at least, the Canadian mining industry as viewed through the eyes of the Metals Controller. There is nothing quite like the Canadian system in the system of controls in the United States, because the Canadian Controller combines the functions of a good many of the organizations here. I think the nearest counterpart would be the Divisional Chiefs of the WPB-although they have perhaps less authority and operate in a somewhat narrower field. My own field, as you know, is the metals and minerals-all of them, as a matter of fact, with the exception of steel and iron and coal and oil. And as I am responsible for supplies not only from domestic sources but also from foreign sources, I exercise most of the functions of the WPB and some of the functions of the Board of Economic Warfare. As my department is also responsible for stock-piling and for the financing of new operations, I therefore exercise some of the functions of the Metals Reserve and also of the Defense Plants Corporation. Being an administrator under the Wartime Prices and Trade Board, I also have the same function in relation w the price of metals as the OP A. The Canadian system of controls is compact, relatively simple, and I believe reasonably efficient. I think two of the reasons for that are that both the Controllers and the Directors of production are clothed with very wide authority, and also the fact that all the buying for the three arms of the service is done through the Department of Munitions and Supply, of which we are a part.

Jan 1, 1943

By A. J. Ouellet, A. Coulombe, B. Salmon

The no. 7 vein system cuts the Ventures gabbro which has undergone folding and fracturing; the latter, in response to movement on the nearby Campbell Lake fault. It fills a shear fracture which pinches and swells in the upper mine levels but has a more uniform width in the lower levels. The best copper and gold grades in the upper levels occur in the widest parts of this structure. The vein is richer in quartz on upper mine levels and in carbonate on lower levels. The north wall of the vein is more affected by major and minor element wallrock alteration than the south wall. The isocumulative ci;rves for gold and copper show a direct correlation between the two metals in the upper levels and their increased concentration in the wider parts of the vein. Gold grade decreases in lower levels. A proposed structural model identifies the no. 3 and no. 7 veins as second order conjugate fractures, related to the Campbell Lake fault. The fractures pattern suggests that a conjugate system developed between these two parallel veins as a consequence of rock competence and a relatively low confining pressure.

Jan 1, 1984

By S Grönstrand, C. Perez, A. B. Yañez, F. Coddou, P. Morales, H. Elgueta

"The TankCell® 300 forced air flotation cell designed and built by Outotec, with active volume of over 300 m3, was installed at Codelco’s Chuquicamata concentrator in September 2008. After that, a program was conducted, where the new cell was tested against the plant’s existing flotation cells of type TankCell® 160, with an active volume of over 160 cubic meters.Testing program was exhaustive and detailed. Grade-recovery curves for each setup were reported, along with recoveries by particle size. Secondly, operational characteristics like air feed and froth height setpoints, and power consumption are compared side-by-side. As the third topic, gas dispersion characterization included velocity mapping, holdup, bubble size and bubble surface area flux operating range. The fourth area of interest was the retention time distribution (RTD) of the 300 and 160 m3 cells in comparison. A detailed campaign using radioactive tracer tests was conducted to clarify this.All of the investigations mentioned above are reported in separate papers for more detail. The aim of this paper is to collect the key findings, and present them in real terms, always referring to operability and metallurgy of the cells. It is destined for people designing new plants and to those improving and expanding existing ones. The most frequently heard question is: will the new large cells operate at same efficiency as the smaller ones. In short, the answer is: NO. They operate at improved efficiency!INTRODUCTIONIn the last two decades of minerals processing, there have been three dominant trends of development in the flotation technology: equipment scale-up, cell characterization and circuit modeling. Equipment scale-up has been rapid in the past two decades. In the year 1990, the largest flotation cell in use was 50 cubic meters of size. This year, 300 cubic meters is the largest installed cell. Characterization of flotation equipment and circuits is a very popular subject nowadays and has helped many operations to improve their recoveries through better control strategies, for example by using optimized air feed and level control profiles (Gorain, 2005), (Doucet, Gomez, Finch, 2006), or through better maintenance (Coleman, Urtubia, Alexander, 2006). Characterization work is closely linked to circuit modeling. The aim is to produce sufficient amount of data to allow reliable model building. These models are then used to design new circuits and to improve existing ones. So in summary, these three lines of development have slightly different aims – from capital and operational cost to performance optimization. Ultimately, they converge in the same end result – maximizing the profitability of the operation. Following chapters will summarize the extensive test work and scientific studies at Codelco Chuquicamata. The aim was to compare a TankCell® 300 cell, with nominal volume of 300 m3, against two TankCell® 160 machines, with 160 m3 volume in each. The work should yield answers to questions: does the larger cell produce similar results – is the scale-up successful?"

Jan 1, 2010

By C K. Bell, L. S. Collett

An AFMAG survey was flown in 1968 over the Upper Nelson River area, Manitoba. The flight direction was northwest-southeast and flight spacing was 2 miles. In the Cross Lake Subprovince, AFMAG showed that an isolated peridotite outcrop was part of a dike that extended over 80 miles. Diabase dikes are not always marked by an anomaly, but isolated cross-overs, when used in conjunction with geological and magnetic data, permit their extrapolation. Anomalies coincide with areas of sulphide mineralization. In the Flin Fion Subprovince, known and unknown northeast-trending faults are detected. The Berry Creek fault was extended south through Tramping lake, then under the Paleozoic cover. Conductors were detected at, or near, the axes of major synclines within Amisk and Snow Group sediments. Granitic terranes have low conductivity and, because they are characterized by smooth AFMAG profiles, they can be delimited. AF.MAG is being recognized as a geophysical method that can aid geological mapping and interpretation. Its most important contribution to the geologist will be in regions where out-crops are sparse.

Jan 1, 1971

By J. M. Cooper

The HBMS reverb furnace in Flin Flon was originally designed in the late 1920s. Throughout the decades campaign life has been increased due to operational practices, technological changes and brick quality improvements. In recent decades the campaign life had been extended such that a complete rebuild was scheduled every 3 years. The latest furnace rebuild and start up has been after a campaign life of nearly 6 years. Brick construction methods and techniques along with furnace operational practices allow the present campaign to be double that of the historical campaign length.

Jan 1, 2007

By J. F. Wright

During the last three years prospecting has been active in southeastern Manitoba and a number of interesting gold, nickel and copper deposits have been discovered within an area 90 miles north of the international boundary, and extending about 40 miles westerly from between mileage 60 and 110 on the Manitoba-Ontario boundary. As known at present, two-thirds of this area of 2,000 square miles is underlain by pre Cambrian granite and granite gneiss and is not likely to contain mineral deposits of economic importance. The remaining one-third is underlain by metamorphosed sediments and lavas (greenstones), penetrated by the granite and granite gneiss and, at various localities, cut by bosses, sills, or dykes of gabbro, diorite, granodiorite, and other types of intrusives. The nickel, copper, and gold mineralization accompanied or followed the intrusion of these different rock types. The gold deposits are limited in distribution, so far as known, to the northern part of this prospecting area and occur along Manigotagan and Wanipigow rivers. These deposits have recently been described in some detail, (3) and therefore only the copper and copper-nickel deposits of the southern part of this area, along Oiseau and Maskwa rivers, will be described in this paper.

Jan 1, 1925

By J. Chretien

The ability to continuously monitor the air quality within a mine has become instrumental in becoming a low cost producer. The many considerations involved in monitoring air quality include sensor type, hardware placement, as well as data storage medium. BESTECH has had the opportunity to gain insight into these air quality monitoring considerations through deployments of NRG1-ECOTM, a minewide energy consumption optimization system. This paper explores the particular challenges overcome through these installations, and provides a set of guidelines for mines that want to maximize data capture while minimizing costs. It provides a view of additional benefits of air quality monitoring, such as ventilation control, reporting and trending.

Aug 1, 2013

By André Chagnon, Yvon Héroux

"Résumé - Cette étude porte sur l'altération de la matière organique et des argiles dans les boues carbonatés dévoniennes du faciès ""F"" de la Formation de Pine Point et ses équivalents stratigraphiques la Formation d'Evie et l'unité bitumineuse de la base de la Formation de Horn River. La matière organique se compose principalement de bitume solide et de quelques fragments de fossiles (organo­ clastes). La majorité des échantillons ne renferment que de l'illite et des interstratifiées illite/smectite.Si on compare les températures d'homogénéïsation (Th = l00°C) des inclusions fluides de la sphalérite et des dolomites associées à la minéralisation aux températures estimées à partir de la réflec­ tance de la collinite (84°C à ll7°C), l'on ne peut pas conclure à la présence d'une anomalie ther­ mique dans le district minier de Pine Point. De plus, la réflectance des organoclastes n'est pas plus élevée dans le district minier de Pine Point que dans les localités plus éloignées des gîtes. L'analyse des minéraux argileux conduit à la même conclusion : aucune anomalie thermique n'est décelable dans les unités échantillonnées à l'intérieur du district minier de Pine Point quelque soit l'indicateur utilisé.La kaolinite et la matière organique altérée, affichant des valeurs anomales de sa réflectance, se trouve essentiellement en présence de soufre et de sulfures. Cela suggère une origine authigène de la kaolinite et une altération de la matière organique reliées au phénomènes de minéralisation.Abstract- The alteration of organic matter and clays is studied in the Devonian Pine Point Formation carbonate muds, ""F"" facies, and its lateral equivalents the Evie Formation and the biturninous unit at the base of the Horn River Formation. The organic matter is mainly composed of solid bitumen with few fossil fragments (organoclasts). Most samples contain only illite and mixed layer illite/smectite.If we compare the Th(l00°C) from fluid inclusions of sphalerite and dolomites associated with mineralization to the temperatures calculated from the reflectanœ (Ro) of the collinite (84°C to 117°C), we cannot detect a thermal anomaly in the Pine Point mining district. This result is based on the reflectance values of organoclasts from the mining district that are not higher than those reflectance values measured on organic matter (OM) away from the ore deposit. A similar conclusion is reached from the clay study: none of the parameters used allow us to identify a thermal anomaly in the samples from the mining district.The kaolinite and the altered OM showing anomalous Ro values mainly occur with sulfides and sulfur. This association suggests an authigenic origin for the kaolinite and an alteration of the OM due to the mineralization events."

Jan 1, 1994

By H. C. Boydell

Introduction Situated in the district of South Lorrain, some 16 miles southeast of Cobalt, Ontario, and reached from that centre either by branch line of the T. & N. O. railway or by what, for a mining camp, is a reasonably good road, the Keeley mine, owned by the Keeley Silver Mines,' Ltd., has had its history recorded by C. W. Knight (1). Silver was first discovered in South Lorrain, in Woods' vein, on Keeley property, in 1907, and the Keeley mine has been described by Knight (2) and Bell (3). The total production to February 28th, 1930, has been 10,760,107 ounces of silver and 1,285. 434 pounds (weight) of cobalt.

Jan 1, 1931

By A. E. Reschke

Optimized mine planning of the Leeville Gold Mine, Nevada, necessitated the requirement for an average of 2540 tpd of high quality cemented rockfill (CRF) in primary stoping blocks and underhand cut and fill workings. To meet this requirement, a number of innovative design features were incorporated into the overall batching plant design. Foremost is the use of a dedicated skip to transfer crushed aggregate from surface down through the ventilation shaft to twin underground storage silos. Also, the use of a high shear colloidal mixer on surface to pre-slurry a cement/flyash binder with pipeline delivery to one of two separate underground CRF mixing stations was incorporated. Finally, the binder and aggregate are combined in a 9 m3 twin shaft compulsory type mixer before loading into teleram trucks for placement.

May 1, 2007

By Alfred W. G. Wilson

THE state of development of its iron and steel industries serves as a 1eading index to the general condition of a nation's business affairs. In this paper, the authors present an economic study of the progress of this group of industries in Canada for the decade 1927-1936. The statistical data and most of the tables which accompany this article have been com-piled by John Casey, Statistician, Bureau of Mines; the text and some of the computations have been prepared by the seni0r author. The principal source of statistical information has been the publications of the Dominion Bureau of Statistics; where other sources have been consulted, they are noted in the text. All weights are given in short tons. Records for the years 1913 and 1918 are also presented in the group of tables dealing with iron ore and pig iron; they will serve as a basis for comparison with nearly normal years in the two decades prior to 1927-36, which included the abnorma1 years of the Great War. GENERAL REVIEW At the beginning of the decade under review, this group of industries had returned to almost normal production, as determined by pre-war conditions. Iron ore consumption showed a steady increase between 1927 and 1930; a marked decline began in 1930 and reached its culmination in 1932, when the recorded consumption of ore was 293,353 to11s, about 16 per cent of the average consumption during the first four years of the decade; the last four years of the decade show a gradual increase in consumption; the amount of ore used in 1936 was still slightly below the amount used ten years before, in 1927 (see Table 1, top).

Jan 1, 1938

By G. Barrasso

REACH was proposed by the EU Commission in October 2003 and stands for the Registration Evaluation, Authorisation and Restriction of Chemicals. It requires that all substances identified as persistent, bio-accumulative and toxic, whether the risk of those chemicals being released is real or perceived, require registration prior to them being allowed to be imported into the European Union. An internal investigation by the metals industry indicates that almost all primary raw materials streams would be classified as hazardous due to the potential health or environmental hazard properties of one or more of their ingredients. REACH uses a wide definition for chemicals and metals and as such its implications greatly impact the entire supply chain of the metals industry. The process of registration would require the producer/ importer to produce a dossier. Initiatives along the same lines as the EU REACH are also coming up in other parts of the world. REACH requires registration of at least four substances manufactured by the aluminium industry: aluminium metal, including powder, aluminium oxide, and aluminium hydroxide. The proposed legislation permits the affected companies to band together to form a consortium to develop certain aspects of the registration application. The aluminium industry has established a consortium and testing is currently underway.

Jan 1, 2006

By A. Roy MacLean

"Cape Breton is an island on the eastern extremity of Nova Scotia, Canada. Here, coal mining under the Atlantic Ocean has been a way of life since the early French militia mined coal for heating purposes in 1720. Despite many ups and downs over the intervening years, the coal industry has survived and is now in a favourable position to benefit from the upswing in international coal usage.Mining in Cape Breton Early mining in Cape Breton was done by hand picks and shovels. The coal was loaded into mine cars which were hauled by horses to the main haulage system for transport to surface. Later, compressed-air cutting machines and drills led to the use of explosives to blast the coal so that it could be loaded by hand and transported as above. In 1923, longwall mining (by hand) was introduced. In 1950, the Dominion Coal Company developed the Dosco continuous miner in order to mechanize the longwall coal-getting operation. At this time, conveyor belts came into wide-spread use, along with diesel locomotives to haul mine cars from the longwall face to the main transport system. During this period, coal was also mined by conventional mechanized room-and-pillar equipment such as cutting machines, loaders, roof bolters, etc. This system evolved into the use of the continuous ·miners of today, which are employed in the Lingan Mine room-and-pillar section. However, this method is only satisfactory at shallow depths and gradients. For these reasons, almost all the coal in this coal field will be mined by longwall methods. In 1968, the Government of Canada expropriated the assets of the Dominion Coal Company on Cape Breton Island in order to prevent complete closure of an uneconomic industry by its owners. The government created, by an Act of Parliament, the Cape Breton Development Corporation which now operates the coal mines, coal preparation plants, railway, shipping pier and ancillary services (Fig. 2). Since its inception, the Corporation has closed three mines, opened two new mines, is in the process of developing a third new mine, and has invested heavily in the one mine which remains from its previous owners."

Jan 1, 1985

By L. H. Shang

The 319 Al-Si alloy is one of the most prominently used aluminium-based alloys in motor vehicle and engine applications, Microporosity present in 319 alloy castings reduces the load bearing capacity of the castings, The quantitative prediction of microporosity levels in Al-Si castings has been a subject of much interest for several years. In this research a new criteria function, tf 1,98 R13° (tf: local solidification time, R: cooling rate) was developed by multiple regression analyses, correlating thermal data from simulation studies to experimentally obtained microporosity values. This new criteria function gives a general prediction of microporosity in 319 Al-Si castings.

Jan 1, 2005

By Tweedy. D. H.

"The paper describes the rapid development of, and operational experience in the utilization of, pneumatic low-pressure pipeline hoisting systems to vertically convey raw coal and rock through shafts, supplementing shaft capacity-the greatest lift to date being 535 m.A typical installation has raised over 250,000 tonnes in less than one year from a depth of 413 m through a 350/ 400-mm pipeline at a rate of 85 tonnes per hour. Operational experience on seven systems has provided valuable data on performance and operating costs.The main advantages of the systems lie in the flexibility of the pipeline to occupy existing free space in shafts and underground roadways, the relatively low first cost, the short delivery and installation time, and the economical running cost.Conclusions are therefore reached on future applications for example, the use of boreholes in older mines where new production technology has outstripped shaft or slope capacity, inter-level hoisting to implement concentration on transport roads and perhaps full mine output from relatively small mines.IntroductionIt is seven years since the basic art and practice of the pneumatic hoisting of minerals was described. The technique was developed in Western Canada by Radmark Engineering and found favour in the United Kingdom with the National Coal Board. Engineering and commercial feasibility trails were conducted in collaboration with the Mining Department and Mining Research and Development Establishment of the N.C.B. There was also considerable involvement with the British Health and Safety Executive.During the last five years, rapid progress has been made in the installation of new systems in the United Kingdom, Hungary and other countries. The operational experience gained makes it possible to report ""in depth"" on these installations, which cover a wide range of different physical mining applications."

Jan 1, 1982