Search Documents

By V. Vakiloroaya

The paper aims at developing a hybrid solar-assisted air conditioner system for performance enhancement and energy efficiency improvement. To increase sub-cooling of the refrigerant at partial loads, we propose a new discharge bypass line together with an inline solenoid valve, installed after the compressor to regulate the mass flow rate of the refrigerant vapour passing through a hot water storage tank. For control design, a lumped parameter model is first developed to describe the dynamics of the system in an explicit form of input-output relationship. The system has been fully-instrumented to examine its performance under different operation conditions. The system model is then validated by extensive experimental tests. The predictions from the models exhibit a good coincidence with experimental results, judging by an RMS error less than 15%. Based on the obtained dynamic model, a linear quadratic regulator (LQR) is applied to optimize a cost function of the output errors and control efforts. The key challenge is to regulate the refrigerant temperature entering the condenser by controlling the valve opening. The design approach is then tested in a transient simulation tool to predict the system performance in transient conditions. The experimental results obtained from implementation with PLC demonstrate that the proposed system delivers higher system efficiency owing to the higher refrigeration effect in the direct expansion evaporator. Thus, the novel development is promising for improvement of energy efficiency, enhancement of the system performance while fulfilling the cooling demand. Consequently, between 25 and 43% of monthly electricity can be saved on average.

Aug 1, 2013

By Eric Barnard, Andreas Nashitati, John Tero, Guy Deschênes, Setta Mbalamba, John Rajala

The Otjikoto Mine, owned at 90% by B2Gold Corporation, is located 300 km north of Namibia’s capital city of Windhoek. The reserves from the open pit mine, estimated at 25.9 million tons with an average grade of 1.28 g/t Au, contain gangue minerals, pyrite and pyrrhotite, and have an estimated 10 year mine life. The feasibility study included an optimisation of gold leaching using CSTR for the original design. The results of the test work were used to establish the design criteria. Gravity tails from three composites (drill cores), representing the major ore types, were used. The XR3 sample (gravity tails) contained 0.32 g/t Au, while the XR2 and XR1 gravity tails samples (used for variability) contained, respectively, 0.30 g/t Au, and 0.47 g/t Au. The optimum leaching conditions were: a pre-treatment of 7 h at pH 10.5 with 100 g/t lead nitrate, DO > 5 ppm followed by cyanidation at 300 ppm NaCN, pH 10.0, DO > 5 ppm for 48 h. The gold extraction was 91.5% (97.2% overall extraction gravity/leach) and the cyanide addition was 0.57 kg/t NaCN. Increasing the DO to 16 ppm did not show any economic benefits. No pre-treatment or a 4-h pre-treatment reduced the gold leaching kinetics. The XR2 and XR1 gravity tails samples had gold extractions of 92.9% and 92.3%, respectively. At the plant scale, an 11 h pre-treatment is used followed by 42 h cyanidation with 250 ppm NaCN and an average DO of 8 ppm and 230 g/t lead nitrate in 2016. The cyanide addition was 0.49 kg/t NaCN. The commercial operation started on February 28th, 2015. The overall gold recovery and production were 98.4% and 145,696 ounces for 2015 and 98.1% and 166,286 ounces for 2016. It was found that retention times, gold content of leach residues and cyanide addition are comparable for the lab and the plant. Details of the Otjikoto process flowsheet are discussed in this paper along with the results of the lab leach optimisation test program and the plant leach circuit performance and improvements.

Jan 1, 2017

By A. E. Wraith, R. Harris, J. Qiu, R. Parra

Small pilot scale experiments have shown that it is possible to almost fully eliminate the minor elements (ME), namely As, Sb, Bi and Pb contained in smelter dusts by vacuum calcination of mixtures of the dust with sulphidizing agents such as dirty copper concentrate or elemental sulphur at 900 °C and 80 +/- 30 Pa for 90 minutes. The products of this calcination are a residue comprising a purified mixture of copper containing compounds along with the gangue constituents and a high sulphur condensate comprising a mixture of the minor element compounds. In particular, the Cu:ME ratios of the concentrate and dust were increased from 250 and 50, from 28 and 12 and from 36 and 8 to roughly 3000, 3000 and 100 for the calcine, for Bi, As and Sb, respectively. It has also been calculated that (i) the copper content of the vacuum calcine may be recovered by feeding it into a Peirce-Smith converter during its slag blow, and (ii) the resulting recycling could increase the minor element treatment capacity of a smelter by 100 % while also reducing the blister As content by a factor of three. The experimental results are briefly discussed and a treated dust recycling option is examined. Example operating conditions are presented and available commercial technology for the vacuum calcination of the mixtures is reviewed.

Jan 1, 2007

By J. S. Stewart

THE Mackenzie River Valley proper extends from Great Slave lake to the Arctic ocean (see map, Figure 1). From Fort Providence, near Great Slave lake, to Aklavik, near the Arctic coast, the distance by river is 1,000 miles. This will give some idea of the extent of the region. Throughout the length of the river valley, the Precambrian complex rocks are overlain by unaltered sedimentary rocks several thousand feet in thickness. These sediments are dominantly marine and Palaeozoic in age. In places, the Palaeozoic strata are overlain unconformable by Cretaceous an Tertiary sediments. The strata have been folded and, in general, the inclination of the beds to the horizontal is comparatively gentle. Here, then, we have the essentials for potential oil fields covering an area over 1,000 miles in length. This is probably the largest comparatively unexplored potential petroleum region in North America, and surface evidences of oil in the form of seepages occur in several places. Many of these seeps were known to the early explorers, and the first Geological Survey report on the Mackenzie River region, containing the results of field work carried out by R. G. McConnell in 1887-88, noted the petroliferous character of the Devonian strata and the indications of petroleum(l). This region is, however, handicapped by distance from markets and sources of supply of materials; by lack of modern transport facilities; by short season for river transport, and mountainous country separating the valley from the Pacific seaboard; and by the long winter season with weather that makes outdoor work difficult. These factors have tended to discourage the enthusiasm of would-be promoters, and so development in this region has been slow In 1920, a test well drilled about fifty miles northwest of Fort Norman discovered oil in commercial quantity, and three additional wells proved a small area to be productive.

Jan 1, 1944

By J. Grignon, C. Fleming

It is possible to reproduce the performance of an operating CIP or CIL plant in the laboratory, in small scale batch kinetic tests, coupled with mathematical models that translate kinetic data into predicted steady state gold profiles across multi-stage adsorption circuits. Once the performance of the commercial plant has been mimicked by the model, the plant operating parameters can be varied systematically in the model, and the likely response of the plant to the step wise change can be determined. In this way it is possible to inexpensively optimize the operating conditions of an existing plant, with no disruption to plant operations and no economic risk to the mining company. This approach had been adopted by IAMGOLD to optimize the performance of their Rosebel CIL plant following several major expansions in mill capacity since 2004.

Jan 1, 2011

By S. Kelebek, B. Nanthakumar

ABSTRACT The sensitivity of sulphide minerals towards oxidation depends on the mineralogical makeup and nature of sulphide ores. This paper focuses on chalcopyrite behaviour in a nickel-copper sulphide- ore matrix that was aged in the mine-site stockpiles. Results of collectorless, collector-induced flotation and recovery by size are presented following a discussion of XPS analysis that was used to gain insight into oxidative alteration of chalcopyrite’s surface chemistry. Chalcopyrite maintains its high flotation activity despite exposure to weeks of oxidative conditions. It is concluded that chalcopyrite is quite tolerant to stockpile oxidation due to various factors related to alteration of its surface chemistry.

Jan 1, 2012

By S. A. Willis

For the past several months 1 have been considering the functions of this Society and its reasons for continuance. The fact that it is now sixty years old indicates that it must have been of value and we all know that it has contributed much that was worthwhile to Nova Scotia and the Maritime Provinces. The question arises: "What is the future of the Society, and how might its activities be altered to suit present-day activities and to be of even greater value?" Let us analyse the various activities in which we are interested and determine which, if any, are of more value than others. First of all, at least once a year we have a two-day convention which constitutes a holiday for the members and their wives. This has always been well planned and has been much enjoyed. Second, there are many social and business contacts made during the meetings and interim meetings. These certainly tend toward better relations and co-operation between the various people concerned. Mine operators meet other mine operators, engineers, people from the education fields, Department of Mines, and so forth. Various sales contacts are made at these meetings which can be of value and use to both the Company selling and the customer. Third, and of greatest importance in any conference, is the exchange of ideas by the members and by authorities from outside, and the presentation of slides and drawings, or actual visits to operations. It is upon this phase that 1 wish to elaborate. These papers are not only presented to our meetings but are generally published in the C.I.M. Bulletin so that members throughout the Dominion have access to them. Many important papers describing new phases of operations have originated through our Society.

Jan 1, 1947

By E. Van Den Neste

A concise historical review is given of the Overpelt plant and the general principles of zinc hydrometallurgy are briefly outlined, together with a description of the new electrolytic zinc plant ore roasting process and, more particularly, the original Overpelt roasting process. A detailed description of the flowsheet of the zinc electrowinning plant, .with an annual capacity of 100,000 t, successfully put into operation in May 1974, is given. The treatment of the residues is performed following the goethite process ; the purification is continuous in two steps; the tank house is equipped with cells containing jumbo cathodes; the handling and stripping of the cathodes is fully mechanized. Concluding the description, some metallurgical and other features of the project are explained in detail.

Jan 1, 1977

By Victor Azbe

Introduction Lime enters our daily life in many ways. Our building, chemical, agricultural, sanitary, and industrial endeavours depend on it to such a great extent that it could probably be called the most important inorganic chemical, and the extent to which it is used might be considered an index of industrial development. Industrial limes vary greatly in quality, due to internal structure and other characteristics. They may be good or bad, sensitive or slow to react. While improper manufacture may not greatly alter the appearance of the lime, it may affect its properties considerably and thus its suitability in the many processes in which lime is used. In some of the processes, one kind of lime is wanted, in others another. While the nature of the stone from which it is made has much to do with whether a lime is suitable or not, its burning and hydration are the crux of the matter. Up to not so many years ago, the knowledge of lime burning was rather imperfect and it is only relatively recently that its manufacture is approaching the state of a higher industrial art. This slow development was in part due to lime manufacture being scattered among many small concerns who, independently, either lacked the inclination or could not afford to strive for a higher technical development.

Jan 1, 1946

By Robert G. Boutilier

So far, most social performance monitoring systems have not gone beyond listing the impacts on various stakeholders. Executives have had to rely on intuition to devise interventions that would improve the impacts. This paper describes a survey process, known as the Stakeholder 360 (S360), which eliminates much of the guesswork. The paper reviews key studies showing that raising the levels of communication, trust, and common vision among stakeholders leads to the acquisition of the resources needed to improve the socio-economic situation. Therefore, the Stakeholder 360 measures the levels of these three factors in the relationships between a company and its stakeholders, and among the stakeholders themselves. In a validation study at a gold mine in rural Papua New Guinea, the S360 produced a socio-political ?roadmap? that showed management and stakeholders alike which relationships need more communication, trust, or common goals/vision. Management used the findings to create alliances that helped the government move forward on a regulatory regime for the mine closure. The community used the findings to focus its planning for life after the closure. An S360 survey conducted six months later revealed a decline in dependence on the mine and an overall increase in levels of mutual understanding.

May 1, 2002

By X. G. Zhao, M. Cai, L. K. Ma, P. F. Li

"Crack initiation stress is one of the characteristic stress thresholds in the rock deformation process under compression. By analyzing AE responses of brittle rocks in uniaxial compression, a new method which is called cumulative AE hit (CAEH) method is proposed for determining the crack initiation stress. An advantage of the CAEH method is that the method removes the user's subjective judgment. To verify the CAEH method, uniaxial compression tests with AE measurement using 77 crystalline rock specimens were conducted. The test specimens cover eight rock classes with different mineral grain distributions. Crack initiation stresses of these specimens were determined by the proposed CAEH method and the LSR method, and the resulting mean crack initiation stresses determined using the two methods were comparable. In addition, taking one rock class with 20 specimens for example, the mean crack initiation stresses determined using the CAEH method and those from several established strain-based and AE-based methods were similar. Hence, the CAEH method can be used as an alternative method for crack initiation stress determination.INTRODUCTIONExperimental observations indicate that the failure process of brittle rocks is associated with crack initiation, crack propagation, crack damage and final strain localization (Brace et al., 1966; Bieniawski, 1967; Lockner, 1993; Wawersik & Fairhurst, 1970). Compression tests on cylindrical specimen are often used to characterize the crack development process. The crack initiation stress (sci), crack damage stress (scd), and peak stress (sc) represent important stress thresholds during the failure process of brittle rocks. Among the three characteristic stress magnitudes, sci is difficult to be determined objectively, directly from examining the stress–strain curves. Some researchers argued that sci obtained from laboratory compression tests is an important parameter for estimating the spalling failure observed in brittle rocks around underground excavations (Andersson et al., 2009; Diederichs, 2007; Martin, 1997). sci can also be used to estimate rock tensile strength and Hoek-Brown failure criterion parameter mi (Cai, 2010). Over the last 40 years, various strain-based methods have been proposed to determine the crack initiation stress in compression tests (Brace et al., 1966; Diederichs, 2007; Eberhardt et al., 1998; Lajtai, 1974; Martin & Chandler, 1994; Stacey, 1981). Nicksiar and Martin (2012) proposed a Lateral Strain Response (LSR) method for establishing sci for low-porosity rocks. Meanwhile, they also used different strain-based methods to evaluate sci of Äspö diorite, and the results showed that all strain-based methods gave acceptable crack initiation stress values. Subsequently, they utilized the LSR method to further investigate the crack initiation stresses in igneous, metamorphic, and sedimentary rocks in compression tests (Nicksiar & Martin, 2013). Compared with previously proposed strain-based methods, an advantage of the LSR method is that it removes the user judgment when interpreting sci. However, the use of the LSR method relies on accurate determination of scd and on having a polynomial fitting equation to find the maximum LSR value."

Jan 1, 2015

By T. R. Chari

The safe-level dilution of low-level radioactive wastes in large volumes of selected granular material is proposed as an alternative method of permanent waste disposal to current Canadian practice of concentration and encapsulation. Accepting the fact that a "background level" of radioactivity exists throughout the world, the authors feel that the concept of controlled dilution of radioactive wastes to a level in keeping with "background" is a plausible alternative to current thinking on the subject and is worthy of equal consideration.

Jan 1, 1979

By A. A. Brant

BECAUSE of its simplicity, the dip needle is widely used for locating magnetic rock formations in drift-covered areas. Although it responds only to strong magnetic disturbances, it has the advantage that surveys with it can be carried out rapidly, at relatively low cost, by untrained operators. More accurate surveys can be made with a much more sensitive instrument known as the magnetometer, but this must be operated by a specialist and the resulting survey costs are much higher. Mining men use the dip needle for the location of magnetic ores or mineral deposits associated with magnetic rocks. In certain districts, a survey with the dip needle may aid in solving geological structure. In the Little Long Lac and Crow River gold camps of Ontario, it has recently been used for these purposes. In interpreting the results of a dip needle survey, an understanding of the chief magnetic and mechanical factors determining the dip recorded by the needle is definitely necessary. For example, many observers locate a magnetic body by the highest dip values, apparently unaware that these frequently may not lie directly above the body. It should also be realized that a careful dip needle survey may yield information regarding the dip, breadth, and perhaps depth, of the magnetic body. Moreover, the observer should know when numerous closely-spaced dip readings are necessary, and when the dip may be measured at more widely separated intervals. The purpose of the following article is primarily to describe the factors affecting the registration of the dip needle, with a view to aiding investigators in a more accurate and complete interpretation of their results. To explain the cause of magnetic disturbances (anomalies) and the action of the dip needle, a knowledge of certain fundamental magnetic terms is necessary.

Jan 1, 1938

By A. Desbiens, R. del Villar

"This two-part paper summarizes the design and implementation of a distributed PIbased control strategy installed at the B grinding circuit, at the Kidd Creek Division of Falconbridge Ltd. Part I details the design of the control strategy using a grinding circuit dynamic simulator (DYNAFRAG). The first step consisted of sampling campaigns and data processing to calibrate DYNAFRAG. Then, several control alternatives were designed and tested with the simulator. The main feature of these strategies is their ability to regulate or keep within an upper and lower limit five output variables (circulating load, rod mill density, cyclone feed and overflow densities and pump box level) with only three manipulated variables (rod mill water, pump box water and rod mill tonnage). By simulation on DYNAFRAG, it was possible to discriminate among several control structures. The preferred control strategy uses a saturation algorithm, which allows the adequate regulation of two measured variables with only one actuator. Controllers located in interacting loops are appropriately tuned, taking into account the existing process coupling. Part II will present the implementation of the selected control strategy.IntroductionSteady state simulators are used to predict the stationary state of a given process under specific operating conditions. Tradi - tionally, steady state simulation has been applied for process flowsheet design, for evaluating process modification benefits or for determining key operating parameters in process operation optimization. Dynamic simulators add a new dimension to process simulation since they allow the prediction of the process transient behaviour, resulting from the application of a different set of operating conditions and/or from natural disturbances or equipment failure. Dynamic simulators can also be used for the training of new operators or for the design of control strategies."

Jan 1, 1997

By Earle J. Klohn

"The design, construction and operation of tailings dams is rapidly becoming a major consideration for most new mining developments, as well as for many existing operations. In North America, under pressure from public opinion, various government agencies have in recent years enacted legislation covering the design, construction and operation of tailings dams. In British Columbia, comprehensive legislation has been passed during the past year (1971). All of these new regulations may be placed into two broad categories: regulations concerning the safety of the dam and appurtenant structures, and regulations concerning the prevention of pollution. Both types of regulation affect the design of the tailings dam facilities. Consequently, they must be considered jointly by the designer. A good tailings dam design must satisfy the basic requirements of safety, pollution control, storage capacity and economy. To achieve this, 'the design must be based on a thorough understanding of both the geotechnical problems involved and the requirements of the mining development. Obviously, this requires close cooperation between the designing geotechnical engineers and the mining operators. This paper outlines the major engineering factors that should be considered in the investigation, design, construct ion and operation of tailings dams. Basic methods of tailings dam construction are reviewed and the advantages and disadvantages of each briefly discussed. Comparisons are made between the design and construction of conventional water supply dams and tailings dams. Examples are presented of some of the problems that may arise during construction and operation of a tailings dam. The paper also explains the need for basic instrumentation of tailings dams and for carrying out simple field tests and measurements during construction and operation. Of prime importance is the downstream monitoring of surface and subsurface seepage flows. These observations are invaluable where contamination of surface and/or subsurface water may become a contentious issue at some future date. Each tailings dam design must be based on a study of the particular requirements of that project. To make a proper evaluation, adequate data must be available concerning a large number of items•, including such things as: topography, hydrology, geology, subsoil properties, seismicity, government regulations, fineness of mill grind, mill water balance, availability of suitable construction materials, volume of water to be stored behind starter dam, downstream development or liability, and many others. The large number of variables involved in such an evaluation often result in the designer considering two or more alternative designs. Selection of the final design, which is usually based on detailed cost analyses of the alternatives, must be made in close consultation with the owner."

Jan 1, 1972

By M. Reda

Inorganic oxidizing agents of the type MeOx-z such as Chromate, Vanadate, Tungstate, and Molybdate... etc. are widely used as corrosion inhibitor. In non acidic solution these oxidizing agent are reduced on the surface of the meta, according to OX + m e + p H20 Red + n OH" In which y = (n-m)/m. The purpose of this publication is to show that for many metals the value of y for any oxidizing agent determines the possibility of that oxidizing agent being an inhibitor or activator for the corrosion process. The inhibition efficiency for other ions such as Pertecnetate and Tellurate which have not been extensively studied can be predicted. A mathematical, equation was derived to express the relationship among the concentration of oxidizing agent, degree of retardation of the corrosion process I cord cor ° (ratio of corrosion current in the solution containing inhibitor to the base solution) , ionic strength of the solution and the coefficient y. The validity of y and the mathematical, equation were verified by many experimental, works on various metals such as zinc, aluminum and steel. Al, the above research works are based on the published research works of Prof. Mikhailoviskii (from 1979 til, 1998) from the Russian Academy of Science.

Jan 1, 2010

By ANNE FUZESY

Soluble potassium salts in bedded underground salt deposits supply most of The world demand for potassium f or agricultural and industrial use. The potassium salts, sylvite and carnallite, were f irs, noted in drillcores in southern Saskatchewan during The search for oil and gas in ihe early /940s. Problems in shafi sinking beset pioneering potash companies, however, and cominuous production did no, begin uniil 1962. Powsh deposits in southern Saskatchewan occur within ihe uppermost 60 111 of the Middle Devonian Prairie Evaporite a, depths in excess of 900 m. Four groups of po/ash-bearing haliie beds have been distinguished: the Esierha-::,y, White Bear, Belle Plaine and Paiience Lake members. Powsh deposiis extend a jell' kilomeires into Manitoba and south imo orth Dakoia and non heasiern Moniana. Individual potash-rich beds are extensive and consistent in grade and Th ickness. Local th ickening occurs where carnallite is the dominani poiash mineral. Th e preferred ore, sy lviniie, is a clean mixiure of sylvite and haliie. Carnalliie and insolubles are avoided wherever possible because of Their detrimenwl effects on mine stability, grade and refining. Sy lvin ite is exTracted by underground mining or brought TO swjace as brine in solution mining. Poiash is separaiedfrom halite byfloiation or sequential crystallization. The refined produci, potassium chloride, is employed as a fertilizer ingredient as well as in chemical and other industrial capaciiies. The ten poiash mines of Wesiern Canada all are in Saskatchewan and account for aboui 25 per cem of world production. Faciliiies are being expanded, and a new mine and refinery was planned for ihe Breden bury area. Deposiis in Manitoba also were being evaluaied.

Jan 1, 1984

By C. O. Stee

IN the October, 1936, issue of the Canadian Mining Journal there was published a series of very comprehensive and exccellently illustrated papers by Mr. C. O. Stee and members of his staff dealing with Siscoe operations and ore-bodies. These were, in the order in which they appeared: Geology of Siscoe Gold Mine, by O. L. BACKMAN Diesel Power at Siscoe Gold Mines, Ltd., by C. O. STEE andE. A. BLOMQUIST Mining at Siscoe, by L. T. POSTLE and W. F. Engineering and Surveying, Siscoe Milling Practice, Research and Testing Laboratory, Assaying of Mill Tails and Solutions, BROWN(6) by P. A. TEEPLE (7) by L. E. DJINGHEUZTAN by L. RIVETT (8) by G. IRWIN (9) The Editor of the Canadian Mining Journal cordially assented to our suggestion that these papers be reviewed at the 1937 Annual General Meeting of the Institute, and the authors very kindly accepted our invitation to present such reviews . Of these courtesies, full acknowledgment is here accorded. To our readers, we commend the original papers in the Canadian Mining Journal. The summaries presented at the meeting follow. EDITOR. THE GEOGLY OF THE SISCOE MINE The Siscoe gold deposits lie in and near a stock of granodiorite, related to the Bourlamaque batholith, which has intruded highly folded Keewatin volcanic rocks .. The volcanic rocks lie to the north of a belt of Timiskaming sediments.

Jan 1, 1937

By J. G. Manchuk, M. Thurston

"The degree of uncertainty associated with a natural diamond resource is important to quantify from the time of discovery through the production lifetime. Data collection occurs during the discovery, exploration, delineation, and production or recovery phases. Quantifying the relationship between data and uncertainty is an important component of project valuation. The value of data is measured as their potential to reduce uncertainty if they are collected. A method is developed using Monte Carlo simulation for predicting resource uncertainty and valuing data during critical phases of development, particularly discovery and exploration. The technique is applied to diamond pipe deposits.RÉSUMÉ Il est important de quantifier le degré d’incertitude associé à une ressource diamantifère naturelle, depuis le moment de sa découverte et durant toute la durée de l’exploitation. La collecte de données se fait durant les phases de découverte, d’exploration, de délimitation, et de production ou de récupération. La quantification de la relation entre les données et l’incertitude est une composante importante de l’évaluation du projet. La valeur des données est mesurée en tant que leur potentiel à réduire l’incertitude si elles sont recueillies. Une méthode a été développée qui utilise la simulation de Monte Carlo pour prédire l’incertitude de la ressource et évaluer les données durant les phases critiques du développement, surtout celles de la découverte et de l’exploration. La technique est appliquée à des gisements de cheminées diamantifères."

Jan 1, 2015

By S. Foged

Umicore and MWH jointly demonstrated that mechanical dewatering of goethite and neutralised tailings significantly increased the life of a 30 ha tailings pond and improved the operation of the pond. Umicore operates one of its zinc production plants in Balen, Belgium. As part of its production process, an excess of neutralised and goethite¬containing tailings is generated. These have historically been stored inside large lined ponds. As the storage area of the current goethite pond was nearing its capacity, Umicore studied the potential for an extension to the existing embankment. However, this extension would face intense regulatory scrutiny, because the environmental and safety impacts were considered important. Together with Umicore, MWH suggested and investigated an alternative treatment approach consisting of mechanical dewatering prior to storage. A feasibility study was prepared where wet storage was compared to dry storage. Differences in safety risks, environmental impacts and economic costs were outlined. The study demonstrated that the life of the tailings pond could be increased from 6 to 22 years, seriously reducing the environmental impacts and safety risks at no significantly higher cost than would have been incurred with the continued operation of the existing pond. The results of the study are presented in this paper.

Jan 1, 2006