Search Documents

By H. J. McQueen

Aluminum was hot worked at 400 - 500°C and strain rates (e ) of 0.004 -0.1s-1, under reversing strains (c) of 0.5 to 0.2 or 0.5 to 0 and also advancing from 0.5 to 1 or 0.5 to 5. Under similar test conditions for different parts of the strain paths, the average measured flow stresses are found to agree with each other. In the forward and backward strain path tests, the almost identical steady state plateaus affirm the occurrence of dynamic recovery (DRV). On reversal of strain direction at constant e , there was generally negligible Bauschinger effect. In specimens annealed at 400°C, static recrystallisation (SRX) was followed microstructurally. mainly by disappearance of elongated grains with serrated boundaries because the new grains were only little a finer than the old due to low strain energy. The only influence of reversing strain path observed was the effect of change of grain boundary area as grains elongated or returned towards equiaxed. In optical microscopy, elongated grains with serrations and deformation bands confirmed DRV in forward path specimens. In reverse path specimens, equiaxed grains were gradually restored with retention of serrations and bands. In low magnification polarized optical microscopy, grain alignment increased with strain for forward path specimens; whereas it decreased in reverse path ones, supporting DRV. Orientation imaging microscopy (OIM/SEM) revealed that elongated grains are broken up as deformation bands rotate during the forward path and that grains return to equiaxed appearance on backward straining. Comparative studies using optical microscopy in polarized light (POM), OIM/SEM and transmission electron microscopy (TEM) revealed that while subgrains remain equiaxed and constant in size and character during the forward and backward paths, the fraction of low angle facets decreased while that of high angle grain facets increased with increasing strain; these are coupled with a fairly low fraction of medium angle boundaries. The results contribute to the understanding that dynamic recovery in aluminum maintains sub-boundaries with low misorientation but as grains elongate and more subgrain become adjacent to grain boundaries the fraction of high angle boundaries rises (with backward straining it was vice versa).

Jan 1, 2007

The AG/SAG circuit discharge P80 is now increasingly referred to as the ?Transfer Size? or T80 for short. From the literature it is apparent that in circuit design some approaches to the sizing of AG/SAG mills as well as the ball mills that they feed use this parameter. This paper reviews whether the use of the T80 is appropriate in this context. In the course of the review examples of AG/SAG discharge size distributions measured from range of operating circuits are used to illustrate the arguments made.

Jan 1, 2012

By William G. Pariseau

"This contribution describes linkage of stress concentration at the face of tabular excavations, for example, longwall coal mine panels, at a meter scale to surface subsidence at a kilometer scale. Joints are considered according to orientation and spacing at an intermediate scale. A new dual-node, dual-mesh technique based on first principles uses a multi-scale technique that allows for computing whole mine surface subsidence while also allowing for computational details of stress, strain and displacement about main entries and pillars, panel entries, and bleeder entries. The technique is implemented in a conventional continuous Galerkin finite element program that has been in use for many years.The advantage of the dual-node, dual-mesh technique is the capability to do a whole mine analysis that takes into account interaction between all sections of a mine where stress transfer over long distances is often the rule rather than the exception while at the same time allowing for details of stress concentration at working faces where caving is initiated and subsidence begins. The technique, outlined recently during ARMA 2014 (Pariseau, 2014), is applied to an underground coal mine in central Utah where mines are developed from outcrops in steep canyon walls. Meshes contain over 10 million, three-dimensional nodes; runtimes are typically overnight, as a practical matter. Results compare favorably with mine subsidence measurements made over a period of several years and show the capability of this new technique to provide useful design guidance for tabular deposits such as underground coal mines. The role of variability or uncertainty in strata properties is illustrated in element safety factor distributions about development, bleeder and main entries and pillars. Such details are new in this contribution. Energy tracking for mine-induced seismicity is also new. Results show a high correlation between number of events and failed elements and suggest a simple index to mine induced seismicity."

Jan 1, 2015

By E. Latorre, T. S. Golosinski

ABSTRACT; his paper proposes new methodology to define the pit limits that yield the maximum net present value (NPV) for a deposit, under a given economic scenario and for a given discount rate. The method uses an algorithm that combines dynamic programming and heuristics. It was tested for evaluating deposits with different sizes and various grade distributions. For the discount rate of zero, the results confirm that the economic pit limits are the same as that defined using Lerchs Grossman method. However, when discount rates higher than zero are used, the pit limits differ, yielding a higher NPV.

Jan 1, 2011

By Ltd. (CYMCO) Technology Center Yunnan Metallurgical Group Co., S. Jian, T. Song, J. D. Miller

"As sulfide zinc ore deposits become exhausted, nonsulfide zinc ore deposits become the other resource for zinc production. However, flotation for zinc recovery from nonsulfide deposits is much more difficult than the flotation of sphalerite from sulfide deposits and may become an option for zinc production only if a suitable processing technology is developed. In this regard, research efforts are being devoted to the flotation of nonsulfide zinc oxide minerals. Some common methods which have been used for the flotation of zinc oxide minerals include sulfidization-flotation, activation, and direct flotation with anionic and cationic collectors. The traditional flotation techniques have low efficiency and difficulty in separation and recovery of the zinc minerals from gangue minerals, for example, smithsonite (ZnCO3) from other carbonate gangue minerals and hemimorphite (Zn4Si2O7 (OH)2·H2O) from silicate gangue minerals. In this study potassium lauryl phosphate was evaluated as a collector for the flotation of nonsulfide zinc minerals. Results from contact angle and microflotation experiments at pH 6–9 show that hemimorphite (Zn4Si2O7 (OH)2·H2O) can be floated from quartz and that smithsonite (ZnCO3) can be floated from calcite. However, when dodecylamine, which is a common collector reported in literature for the flotation of nonsulfide zinc minerals, was used as collector, no significant difference between nonsulfide zinc minerals and gangue minerals was observed at any pH value. Initial evaluation suggests that potassium lauryl phosphate is effective at low concentration and may be a promising collector for zinc oxide mineral flotation.INTRODUCTIONBefore the twentieth century, zinc was mainly produced from nonsulfide ores (Large, 2001; Gilg, Boni, & Cook, 2008). With the development of differential flotation processes in the late 19th century major production switched from nonsulfide zinc sources to sulfide zinc ores (Hitzman, Reynolds, Sangster, Allen, & Carman, 2003; Gilg et al., 2008). However, as it is becoming more difficult to find new sulfide ores, recovery from nonsulfide deposits is being considered. Nonsulfide flotation for zinc recovery is much more difficult than the flotation recovery of sphalerite from sulfide deposits and may become an option for zinc production if a suitable technology is developed. Zinc and lead oxide ores are difficult to beneficiate ores due to their similar floatability with gangue, high solubility in water, and the influence of slimes (Fa, Miller, Tao, & Li, 2005). In order to improve the performance of oxidized minerals, lots of effort is being devoted to this field of study (Ejtemaei & Mahdi, 2014)."

Jan 1, 2016

By M. H. Colebrook

Nickel laterites contain about 70% of all continental or terrestrial nickel resources; therefore the recovery of nickel from lateritic ores has large economic significance. The processing of lateritic ores involves the preparation and movement of concentrated aqueous suspensions. However due to complex characteristics and non-Newtonian properties, ranging from shear-thinning to shear-thickening and from thixotropic to rheopectic, a basic understanding of the flow behaviour must be developed. This understanding will assist in the development of new plants and the operation of existing plants. The work in this paper involves the characterization of three ore types from the Vermelho ore deposit to categorize them as rheologically simple to complex. Rheological testing was also conducted on pure mineral samples that represent the main minerals in these samples. The results show that the rheological properties of the ore types can be related to the surface properties and physical characteristics of the main mineral constituents.

Jan 1, 2006

By H. Hitchen

THE PURPOSE of this paper is to indicate the working capacity of different types of ropes for various engineering and mining duties. ROPE CONSTRUCTIONS There are approximately one hundred different designs of ropes in use today but, normally, only about ten are necessary for mining and engineering duties. The rest are designed for unusual equipments, or are different ways of combining wires of special shapes. Basically, the various designs of mining ropes consist of round, triangular, and oval strands, constructed with one or several layers of wire over a single wire, or a compound construction of sever.al wires. To suit different installations ropes are made with 3, 4, 5, or more of these types of strands over a central core, the ?co re itself being manufactured from either a fibrous material or a combination of steel wires. Nevertheless, in mining, the demand for 'locked coil rope', wl1ich may be considered as a single strand, is steadily increasing, especially for use on vertical shaft winding engines. So far as the locked coil rope is concerned, many constructions have been developed to suit different requirements, such as - in addition to winding ropes - aerial carrying Topes, shaft guide ropes and haulage ropes.

Jan 1, 1957

By F. Awotwe-Appiah, P. Koshy, A. Y. Fosu, J. Dankwah, J. R. Dankwah

Ghana currently exports its bauxite raw without any value addition. Gradual depletion of high grade bauxite (with high alumina content) and the emergence of low grade bauxite (with high iron oxide content) calls for novel and inexpensive ways to recover alumina from these low grade ores. Bauxite users have indicated their willingness to pay 10% to 50% higher for a corresponding reduction in impurities by a similar amount. This project therefore investigates the carbothermal upgrading of the Ghana Awaso bauxite using waste polypropylene as reductant in a locally designed gas-fired furnace. Composite pellets of low grade bauxite sample (assaying 45% Al2O3) containing pulverised waste polypropylene were formed, oven dried, placed in fireclay crucible and fired for 30 minutes. The magnetic fraction after reduction was separated by a Low Intensity Magnet and weighed. It was observed that up to 97% of the iron oxides (occurring as hematite and goethite) could be separated into the magnetic fraction as magnetite leaving a nonmagnetic fraction with over 98% Al2O3 as opposed to the 45% Al2O3 in the as-received bauxite sample. This research direction provides yet another simple but effective way for simultaneously upgrading low grade bauxite and recycling waste polypropylene, whilst at the same time decreasing the amount of waste material generated as red mud after the Bayer process.

Jan 1, 2015

By Joseph Sawicz

By now, the concept of remotely controlling heavy equipment in underground mines has become commonplace. Personnel safety is the biggest justifier for remote control, followed by an inherent cost saving (in certain cases) when wireless video is added to the mix. There are a handful of vendors targeting this need, and for years the mines have remained loyal to their brand. But as the number of remote-control related accidents and maintenance costs increase it forces our industry to take another look at this commonplace concept. And as the blinders are taken off, the mines are getting the revelation that not all remote control systems were created equally. This paper highlights the differences between various remote control systems, and then moves into an in-depth look at HARD-LINE?s package which drastically cuts maintenance costs, and also provides a solid investment toward full Tele-operation.

Apr 1, 2005

By Qingxia Liu, Mingbo Zhang, Hongbo Zeng

The shortage of freshwater has been a major challenge for mineral flotation in arid areas. When using high salinity water, certain electrolytes are detrimental to flotation while others can improve the flotability of minerals. In this paper, the flotation behaviors and contact angles of pyrite in both Milli-Q water and high salinity water were investigated using different collectors at various pH levels. Results show that the thionocarbamate has a less affinity to pyrite in different solutions under mildly alkaline conditions as compared with potassium amyl xanthate (PAX) and N-isopropoxypropyl-N’-ethoxycarbonyl thiourea (iPOPECTU). At high pH levels, the slime coating on pyrite surfaces, which is caused by colloidal precipitates of magnesium and calcium ions in seawater, was confirmed by SEM, EDX and in-situ zeta potential measurement. The slime coating of colloidal precipitates on mineral surfaces led to low recovery of pyrite at high pH levels. The study of flotation behavior of pyrite in high salinity water improves our fundamental understanding of mineral flotation in seawater.

Jan 1, 2015

"In many gold deposits, a reasonable amount of the gold that remains in the cyanide leach tailing is associated with pyrite. Some gold plants have found it economical to incorporate gravity circuits on the cyanide leach tailing to recover the gold bearing pyrite before subjecting it to fine grinding, then recycling the ground pyrite back to the cyanide leach circuit. For low grade gold deposits the loss of gold bearing pyrite is exacerbated as the broader process economics normally favour a coarse grind (> 150 ?m). An option that has received attention over the last decade is to recover the gold bearing sulphides in the milling circuit by gravity, similar to the widely-practiced gravity recovery of free liberated gold. The modelling and simulation of a gravity gold circuit in a milling flowsheet is relatively simple compared with a gold bearing pyrite circuit, as the recycle advantages and breakage functions for gold and pyrite are quite different. This current work represents an attempt to simulate the gravity recovery of gold bearing sulphides in a milling circuit that also incorporates fine grinding, using relatively simple simulation models. The simulation results are further explored with reference to the economics of this type of circuit.INTRODUCTION It is well known that gold is associated with pyrite in most sulphide gold deposits and that the amount of gold associated with pyrite will vary from deposit to deposit. Most of the gold associated with pyrite is liberated in the grinding circuit during the processing of a gold ore. However, some gold remains occluded in the pyrite and is lost in the final leach tailings. Little information is available in the literature on methods to enhance gold liberation from pyrite by specifically removing pyrite, either in the grinding circuit or from the final tailings stream, and grinding it finer. One of the earliest record of this approach is described by King (King, 1949) where pyrite present in Witwatersrand gold ores was recovered by circular jigs and Johnson barrels followed by fine grinding of the concentrate prior to cyanide leaching. Dominy et al., 1970, provides information on the use of Yuba jigs to recover pyrite from the discharge end of ball mills. Again, the jig concentrate was ground to a fine particle size before cyanide leaching to recover the liberated gold. Unfortunately, no information is provided in these articles on the additional gold recovery from implementing these circuits in a flowsheet. Martins et al., 1993, provides details of a gravity circuit using Reichert cones and spirals to recover gold bearing pyrite from a cyanide leach tailings followed by fine grinding of the pyrite concentrate in a Tower mill. The ground concentrate returned to the front end of the already installed leach circuit. Overall recoveries were increased by some 2% to 4% depending on the amount of gold and pyrite in the plant feed."

Jan 1, 2017

By David S. Wong

With air emission limits for total particulates continually tightening, management of `potroom dust' or airborne particulates from aluminium smelting potrooms is of increasing importance. To better understand how settled and airborne particulates are generated within a potroom, methodologies have been developed to sample and analyse the compositional signature of dust, in relation to its sources. During a smelter case study, these methods allowed tracking of mineralogical phases in dust across a range of potroom locations, showing that the mechanisms of dust generation do vary spatially and vertically in a potroom. Such methodologies may also be applicable to other metallurgical industries.

Jan 1, 2011

By Warren A. Sheaffer

THE chief uses for copper are as a conductor of electricity and as the chief component in brasses and bronzes. For such uses, the copper must be of very high purity. H the impurities are zinc, iron, lead, arsenic, or antimony, they can be removed to a great extent by fire-refining. H, however, gold, silver, nickel, or cobalt are present, electrolytic refining is necessary. Electrolytic refining must be preceded by fire-refining and hence all impure copper must be fire-refined. The electrolytic refining of copper is most efficiently carried on when the impurities in the anodes are at a minimum. Some of the impurities tend to deposit with the copper at the cathode, while others remain in solution, decreasing the conductivity of the electrolyte and thus increasing the voltage necessary for refining. Since these dissolved impurities must be removed by continuous purifications, the amount of impurity in the anode copper should be reduced by furnace refining to some predetermined limit. Anode furnace operation aims to reduce these impurities to a minimum beyond which the cost of further furnace refining would exceed that of removing the remaining small amounts of impurities from the electrolyte. The anodes should have a fine-grain internal structure because any pieces of metal becoming detached from the anode during the electrolytic refining are inconvenient to remove from the cells and may cause short-circuits. Impurities tend to disrupt such a structure and thus form zones of weakness during corrosion. When the impurities are reduced to a satisfactory mini-mum, the anode, due to having a fine-grain structure, will corrode uniformly over the entire surface area exposed to the electrolyte. Oxides of the impurities may be volatile, in which case they pass off as flue gases, or they may form viscous slags having a lower specific gravity than molten copper, thus permitting their removal by skimming. Some impurities can be oxidized by introducing air into the bath. Due to the large solubility of oxygen in molten copper, oxygen is distributed uniformly throughout the bath and thus comes into intimate contact with all impurities. The oxides which are insoluble in molten. copper are removed either as flue gases or as slag.

Jan 1, 1942

By K. Stankiewicz

Projects as regards state-of-the-art mechatronic systems aiming at increase of safety in the mining industry and at improvement of coal production technologies, which have been completed at the KOMAG Institute of Mining Technology, are presented. These projects cover automation, monitoring and visualization systems, systems for implementation of artificial intelligence techniques, and database recording systems. iRIS system for electronic marking, identification, and recording of components of powered roof supports, which was implemented in 31 Polish mining enterprises, is presented as an example of the work directly associated with an increase of operational safety. Specialists from KOMAG, ELSTA, Ltd., and Silesian University of Technology in Poland, have developed flexible, configurable, and scalable system for data management, which refers to all fixed assets of mining enterprises, meeting the requirements of users as regards marking and identification of fixed assets. The system for control of roadheaders using intelligent algorithms, based on artificial intelligence techniques is also the example of innovative actions. This system aims at increasing the safety and effectiveness of teamwork due to a possibility of remote, semiautonomous operation. Introduction of artificial intelligence technology enables adaptation of roadheader mining system to the present mining-and-geological conditions. Moreover, work aiming at implementation of state-of-the-art system for control of mine jig?s beneficiation node, integrating machines and equipment in one system, is carried out as regards automation, information integration, and visualization in coal beneficiation process. Work on recovery and conversion of thermal energy, which is a by-product during operation of machines and equipment, especially mine diesel drives, is presented. Systems for energy recuperation are more and more important due to the necessity of continuous increase of power production efficiency.

Aug 1, 2013

By Jan W. Merks

The objective of metrology in mineral exploration is to derive unbiased confidence limits for masses of metals contained in reserves and resources. Sets of test results for gold and silver determined in pairs of interleaved bulk samples give unbiased confidence limits for the central value of each metal. The same sets of test results show how to verify spatial dependence by applying Fisher?s F-test to the variance of a set and the first variance term of the ordered set. A significant degree of spatial dependence gives a higher degree of precision for the central values of gold and silver. Plotting variance terms of an ordered set against the variance of the set and its lower limits of asymmetric 99% and 95% confidence ranges gives a sampling variogram. Sampling variograms put in plain view where spatial dependence in sampling units or sample spaces dissipates into randomness. The application of statistical methods to test results for sets of ordered core samples within boreholes, and for sets of ordered ore volumes within profiles, plays an important role in defining reserves and resources.

Oct 1, 2009

By M. Maldonado

This work details the application of a decentralized control strategy to a pilot flotation column working with a two-phase system (water-air). The process is represented by a multivariable system composed of three inputs and three outputs. The selected control variables are the froth depth, the air hold-up and the bias rate, whereas the corresponding manipulated variables are the set-points of the local flow controllers of tailings, air and wash water. All controlled variables are estimated using electrical conductivity based techniques. In particular, the results of a new method for estimating the bias rate, based on the measurement of the volumetric fraction of wash water under the interface, is presented. This method reduces the coupling problem associated to the bias estimation as a difference between feed and tailing water rates. Moreover, the nominal system transfer matrix can be represented by an upper triangular matrix, in such a way that the closed-loop system stability reduces to the stability of the independent control loops. The experimental results show that the closed-loop system performance, particularly that of the bias rate loop, is strongly dependent on the air flow rate, reaching in some cases the saturation point of the controller.

Jan 1, 2007

By E. Fritz

This paper reviews the history, developments and 10 milestones of the oxygen steelmaking processes, with a special focus on conventional autothermic converters, high-speed converters with a blowing rate up to 5 m3n/t min and allothermic converters with coal addition, post combustion and the possibility to increase the scrap rate up to 50%. Related operating results are introduced. A new process route, which is based on hot metal and chromium ore, is outlined. The cost advantage for the production of 304 stainless steel grade is higher than 100 USS/t. The synthesis of EAF and oxygen converter steelmaking, a comparison of decarburization rates, refining combustion burners for optimized oxygen-management in EAF and an example for a large advanced EAF are outlined. Possibilities of flexible steelmaking and the growth and outlook of worldwide oxygen steelmaking are described.

Jan 1, 2004

By D. D. Liu

This paper proposes a charge induction dust measurement method based on detrended fluctuation analysis (DFA) for use in coal mine environments, based upon electrostatic interference, dust properties, wind speed, particle size, moisture content and other factors. In this methods, sequence x(t) is first obtained through a dust concentration sensing probe, and then the cumulative deviation y(t) is calculated, and y(t) is divided into same lengths. Secondly, a first-order linear fit is used for data of each interval, and mean-square deviation filtered DFA was calculated for each interval. Finally, the dust mass concentration of the corresponding time is obtain by supplemented calibration coefficient and fitted the data point which is the mean and square root for all lengths of interval. Simulation and verification experiments showed that the charge induction dust measurement method based on DFA can reduce coal mine electrostatic interference effects with high accuracy. The design has been successfully applied to select areas.

Aug 1, 2013

By R. Gutray, J. E. Grainger

This paper deals with the use of a cement-deslimed mill tailings mixture for a scraping floor in cut-and-fill stopes at Madsen Red Lake Gold Mines Limited. It describes the mixing and placing procedures and the precautions used with respect to the floor while mining in the stopes. Details of the mix are presented, and advantages and disadvantages discussed. The paper concludes with a brief outline of the costs.

Jan 1, 1966

By E. M. Cameron

Reconnaissance radiometric and geochemical data have been obtained for an area on the western shore of Wollaston Lake that includes the Rabbit Lake uranium deposit. The study area is extensively drift cover ed. The geochemical data were obtained by analysis of center-lake sediments and surface waters for a variety of elements and other constituents. The airborne radiometric data comprise measurements of eU, eTh and K obtained with a .50,000-cc NaI (Tl) detector at a mean terrain clearance of 120 m and 5-km flight-line spacing. Uranium in lake sediments and uranium in waters are the most effective geochemical indicators of uranium mineralization; the other elements measured are not notably anomalous. A sample site density of one per 1 8 km 2 is more than adequate for identification of the mineralized area. Because many water samples contain close to or below the current analytical detection limit of 0.05 ppb U, the use of sediments is generally favoured. for broad-scale reconnaissance in the region. Uranium in these lake sediments appears to be little influenced by variations in the organic or iron and manganese content. The most effective radiometric indicator of the mineralization is the eU/eTh ratio. This parameter is less influenced by environmental variation on the ground beneath the flight line than eU alone . The eTh/K ratio is anomalous under the Athabasca Formation unconformity where, in places, the uranium mineralization is localized.

Jan 1, 1977