Search Documents

By Dao Dac Tao

The Vietnam coal industry in recent years has achieved the rapid growth. However, in the process of industrialization and modernization of the country, the demand for coal for energy is constantly increasing. This paper presents the Vietnam coal industry in the last stage: the opportunities and challenges facing the coal industry as it strives to become modern, highly effective and capable of meeting the demands of national energy security, all in harmony with socio-economic and environmental needs.

Aug 1, 2013

By B. Friedrich, N. Anastasijevic, S. Stopic

The extraction of nickel from Serbian and Western Australian lateritic ore by sulphuric pressure acid leaching (PAL) has been studied. The following parameters were tested: stirring rate, acid to ore ratio, reaction time, pressure and temperature. These studies were performed with ore samples from the Rudjinci, Serbia and Silcrete, Australia, both belonging to the laterite-silicate group of deposits. An increase of the reaction temperature and the stirring speed at a fixed acid/ore ratio showed a positive influence on nickel extraction. The decrease of the oxidation potential with time correlated with the increase in Fe(II) in solution and nickel extraction as the reaction went to completion for both ores. The target values of 95 % Ni extraction and 60 % Co extraction were attained in 5 min at 250°C for the Serbian silicate ore, at an agitation rate of 1500 rpm, 10 % solids, and acid/ore ratio of 0.40. Under similar conditions only 60 % Ni, but 69 % Co could be extracted from the Australian Silcrcte ore due to different mineralogy. The nickel extraction was shown follow a diffusion-controlled reaction model.

Jan 1, 2004

By George R. White

"The Phalen Colliery, the Cape Breton Development Corporation's flagship, is now producing thermal and metallurgical grade coal in Eastern Canada's Sydney Coal Field. The colliery is a drift mine operating under the waters of the Atlantic Ocean. Improved mechanization, including a 2200 tonne per hour cable conveyor, and the introduction of modern retreat longwall mining methods as part of the Phalen concept are now paying off in better productivity and low operating costs. Geological conditions within the coal field are consistent with plans for ever greater outputs in the 1990s. Although much of the current production improvement is related to uprated machine capacity and simplified mines planning there is potential for even further development in the areas of maintenance, process control and engineering. Human resource development will also be a key factor. These programs are now well under way and Phalen Colliery is poised for top results in the 1990s. Comparison of the CBDC's top producer with similar operations elsewhere in the world, quantifies that potential.IntroductionAn exciting new mining project which has recently started production on Canada's East Coast has been conceived and designed to be one of the most modern and productive coal mining operations in North America.As with all mining operations, the business is basically that of material transportation. Daily, the product is transported many kilometres from the underground face to the surface and then to washing facilities. Men, materials and equipment are transported to and from the surface and the operating faces and services, such as electrical power, ventilating air, fresh water, discharge water, communications and compressed air are supplied throughout the operation to cover operating requirements. On all accounts the operation has been designed to take advantage of the latest proven technology."

Jan 1, 1990

By K. Reipas

"Westmin Resources Ltd. operates the 3300 TPD H-W underground copper/zinc mine on Vancouver Island. Ore storage underground is handled in a 6000 tonne coarse ore bin and a 3000 tonne fine ore bin. Both of these bins have experienced significant wear since excavation and construction in 1985. Wear problems have included both deteriorating rock walls as well as worn out steel liners and concrete at the discharge points from the bins. Extensive rehabilitation work was completed in 1993.The basis o/this paper is the rehabilitation work done on the coarse ore bin. The design and installation of ground control measures are discussed. The bin access methods used to allow the work to proceed quickly and safely are also presented. This involved the use of a Tekfoam safety bulkhead to protect workers.IntroductionMine DescriptionThe H-W mine was commissioned in 1985. Mine access is by vertical shaft with most production areas at a depth of about 500 m. Host rocks are composed of andesite and rhyolite. Mine capacity of 3300 tonnes per day is achieved mainly by longhole open stoping methods, complemented by room and pillar mining. Metals recovered from the massive sulphide ore are copper, zinc, gold, and silver. Mineable reserves at January I, 1994 were 9.7 million tonnes."

Jan 1, 1995

By N. J. Duncan

"Coal mining, whether surface or underground, has hazards that make it unique in the field of industrial safety and health. The often soft, faulted and folded sedimentary strata make wall or roof movement a risk to the safe and economic removal of the coal, while the extraction and handling of coal may create an explosion hazard even in surface operations, In Canada, these problems are compounded by the situation of the coal fields which range from deep undersea deposits in Nova Scotia to steeply pitching thick coal seams high in the Rocky Mountains. Climate too can create its own problems, particularly the effect of metals of minus 40°C temperatures, as crumpled dragline booms at prairie strip mines witness. Because of the difficult and sometimes hazardous conditions, Canada's underground colliery managers, in common with those of other Commonwealth coal-producing countries, must have a government ""certificate of competency"" before being appointed as mine managers. Certification of assistant managers (""under-managers"") and foremen (""fire-bosses"") is also a legal requirement for all of Canada's underground collieries, while the province of Alberta requires certification of surface management personnel. Electricians and mechanics who install and maintain the specially designed equipment underground and in hazardous areas of surface mines and processing plants, and mine surveyors who ensure accuracy of the location of underground workings, must also hold government certificates of competency. The requisites for all certification include a minimum work experience and knowledge of coal mining technology and mine safety and health legislation. Despite recognition of the hazards and increasing knowledge of methods of preventing explosions of flammable gas and coal dust in Canada's underground mines, there have been several disastrous explosions such as those at Springhill Colliery in Nova Scotia in 1891 with the loss of 125 lives, at Hillcrest Colliery in Alberta in 1914 with 189 dead, and more recently · explosions and fires in No. 20 and No. 26 Collieries in Cape Breton. Preventing explosions has required developing optimal ventilation techniques, reducing ignition potential, suppressing ignition at source, draining flammable gas before it can enter the air courses, and preventing, or sealing off, autogenous heatings with their associated carbon monoxide or explosion dangers."

Jan 1, 1985

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to maximise health and safety performance in the mining industry through implementing continual improvement in management of major unwanted events. A comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This will be extended to outburst, coal burst and bumps, interface displays and controls, tailings dams and inrush in 2013. RISKGATE presents substantive and leading edge controls to assist industry stakeholders in the design, management and reporting of organisational and regulatory compliance requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry. All major Australian mining companies are contributing topic experts to this broad industry initiative. In the first 24 months, nine coal mining companies nominated over 80 different experts who contributed over 400 days of individual time to the knowledge capture workshops. RISKGATE is the largest single Australian Coal Association Research Program (ACARP) occupational health and safety (OHS) initiative to date.

Aug 1, 2013

By W. A. Dixon Edwards

Industrial mineral production in Alberta, worth $468 million in 1997, comes from a dozen types of industrial minerals, mined by about 400 producers. Cement and lime from Paleozoic limestone formations exposed along the Rocky Mountains account for the greatest production value. Sand andgravel is the primary source ofmineral aggregate. Almost two-thirds of this aggregate is consumed in the Edmonton and Calgary regions. Sulphur produced at 48 sour gas processing plants and two oil sands plants was valued at $84.8 million in 1997 and accounted for 80% ofCanadian sulphur production. Four companies solution mine the Elk Point salt beds to produce chlor-alkali chemicals, industrial salt and sodium chlorate. Natural brine is also produced as a dust control product. Al $22 million, peat moss is a major industrial mineral product in Alberta. Other minerals with noteworthy production include shale, stone, silica and ammolite. The commodities with the greatest development potential are diamond, silica and oil sands tailings by-product minerals.

Jan 1, 2001

By Northeastern University, B. Y. Cui, B. Y. Wang, D. Z. Wei, W. G. Liu, Z. C. Guan, S. L. Gao

To recover iron values from low grade ores by reverse froth flotation method, further research on cationic collectors used in reverse flotation of iron ores is launched to promote the utilization efficiency of iron ores. In this paper, one new cationic surfactant, bis(2-hydroxylethyl) dodecylamine (BHD), that could be dissolved in water easily was used as collector for quartz flotation. Flotation results indicated that BHD shows stronger collecting performance on quartz than hematite. The maximum recovery of 96.30% to quartz is obtained at a collector concentration of 20.0 mg/L in the pulp pH range from 5 to 7. This collector can be used to float quartz from hematite. And optimal separation results with 86.59% iron recovery and 66.60% iron grade to synthetic sample were achieved at a collector concentration of 20.0 mg/L and pulp pH of 5.02 when hematite and quartz were mixed at a mass ratio of 3:2. The adsorption mechanism of the collector on quartz surface was investigated by XPS analysis, infrared spectroscopic analysis and zeta-potential measurements, which revealed that electrostatic attraction and hydrogen bonding adsorption occur between collector and quartz surface.

Jan 1, 2016

By R. Vergunst, E. A. Devuyst, G. Robbins

"INTRODUCTIONThe Inca process for continuous cyanide removal from industrial wastewaters was patented in 1984 by G.J. Borbely, et.al. (1). The process requires SO2, air, lime and a copper catalyst. Both free and complexed cyanide are oxidized to cyanate in the pH range 8 to 10. Cyanide bound to iron is removed by precipitation as a ferrocyanide insoluble salt and other base metals are removed as hydroxides.The process was piloted in 1982 on barren bleed solution at Campbell Red Lake Mines Ltd., Ontario (2). Since 1982, the Inca SO2-air cyanide removal technology has been applied in twelve commercial installations. The process has significant advantages over other commercial processes in the completeness of cyanide removal and lower reagent requirements and costs.COMMERCIAL INSTALLATIONSBy the end of 1988 Inca will have applied its patented cyanide removal technology to twelve commercial operations. Three of these, namely Scottie Gold Mines, Dupont of Canada Expl. Baker mill and Carolin, all in British Columbia, Canada, have ceased cyanidation operations but SO2-air cyanide destruction results were good for all mills, particularly so for over two years for the Scottie mill.Removal of cyanide from CIL slurry tailings is applied at Equity Silver (9,500 tpd) and Inca's new 1,200 tpd mill at Inca/Golden Knight. Detoxification of CIP tailings is carried out by Colosseum California (3,600 tpd) and Canamax's Ketza River operation (360 tpd). Repulped tailings from Merril-Crowe flowsheets are treated at Total Erickson's Mount Skukum mill (300 tpd) and Skyline's Johnny Mountain mill (200 tpd) and barren bleed at Inco/Queenston's McBean mill (500 tpd). Lynngold's MacLellan mill (1,800 tpd) treats pond supernatant water. Plating shop cyanide effluents are decyanized at Kuntz Electroplating in Kitchener, Ontario. Many of the above commercial operations were described in some detail in previous publications (3,4). Typical installations are described in this paper. A summary of operating results is given in Table 1."

Jan 1, 1989

By C. Gravel, A. Fathi, P. Rivard, G. Ballivy, Z. Moradian, M. Quirion

Knowing shear mechanism of discontinuities under monotonic and cyclic loading conditions is a key factor in stability analysis of rock slopes and rock foundations. In this paper, the effect of cyclic loads on the shear mechanism of joint asperities is described. For this purpose, a fresh tension-split joint from a granite block was used as a reference and thirty five mortar replicas were fabricated. Cyclic shear tests were conducted on replicas under low values of constant normal load (CNL) using a servo-controlled loading system. Tests were performed in two consecutive steps; load-controlled and then displacementcontrolled. In the load controlled part, after initial increase of shear stress to 0.25 MPa, the test was stopped for 2 minutes, then increased to 0.5 MPa, and finally decreased to 0.25 MPa. This process was repeated ten times. At the end, the test was continued up to 10 mm shear displacement under displacement-controlled loading in order to pass the peak shear strength and reach the residual strength. Characterizing joint surface and modeling of involved asperities during the tests was undertaken using a Matlab code developed with new mathematical expressions. The algorithm used in the code is based on three-dimensional coordinates of the scanned joints’ surfaces before and after the test. It was found that a high percentage of degradation happens during the first cycle of loading and during the other cycles, degradation occurs gradually. While comparing tests conducted in monotonic and cyclic loading conditions, it was observed that under low number of cycles, the pronounced mechanism is consolidation of the joint surfaces. This consolidation increases contact areas and, therefore, shear strength parameters.

Jan 1, 2015

By J. F. Liu, L. Chen, C. P. Wang

"Calcite-cemented joints abound in the rock masses of Beishan area, which is the most potential area for the high-level radioactive waste (HLW) disposal of China. The mechanical properties of Beishan granite containing a calcite-cemented joint with a dip angle of 82° was investigated under uniaxial compression and the acoustic emission (AE) characteristics were also studied in this paper. Compared to intact granite, the calcite-cemented joint caused a decrease more than 50% in uniaxial compressive strength and a decrease more than 90% in shear strength. The Young’s modulus was also decreased, while the circumferential deformation of jointed granite was sharply increased. The AE monitoring system successfully recorded the process of micro-crack development and the results indicated that the risk of rock-burst could be reduced due to the appearance of calcite-cemented joint.INTRODUCTIONThe properties of jointed rocks differ considerably from that of intact rock. Due to the difficulties in specimen preparation, analogue experiments with artificially prefabricated fractures are often used to study the mechanical behavior of jointed rock (Chen et al. 2012; Kulatilake et al. 2001; Singh et al. 2001). However, natural joints are not quite similar to the artificial fractures and it is necessary to investigate the mechanical behavior of jointed rocks. Xie et al. 2011 studied the mechanical properties of marbles with natural joints by uniaxial compression tests and found that the uniaxial compressive strength of jointed rock is greatly decreased. With the unaxial compression tests, Jacobsson 2005, 2007 tested the intact and jointed granites, which were taken from the potential site for high-level radioactive waste (HLW) disposal of Sweden. However, no significant difference in strength or modulus was found. The above research results are inconsistent and it indicates the complexity of the mechanical properties of natural joints."

Jan 1, 2015

By Terry Aben

Outline ?Review of standards that can be used to identify current coating conditions and optimal points to perform coating maintenance. ?Identify how standards can be used to extrapolate the future condition of coatings to achieve predictive maintenance planning. ?Demonstrate how the above can be combined with project estimating to generate a data driven, quantitative, predictive, risk-based asset integrity maintenance program for Protective Coatings. The Value of Asset Integrity Programs ?Maximize the benefit produced from the investment in maintenance spending. ?Get the best bang for your buck! ?Don?t perform maintenance work before it is necessary ?Money is invested early with no increase in the service life extension. ?Don?t delay until it is too late. ?Planned Maintenance is far less costly than Reactive Maintenance. ?Identify the Optimal Point for Maintenance.

Nov 1, 2011

By Claude A. Jr. Seger

Introduction This paper presents in detailed form the results of settling tests that were published in a few preliminary notes in the April 1949 issue of the Bulletin (p. 166). Carborel is the trade name for sodium carboxymethyl-cellulose and aluminium carboxymethyl-cellulose produced by the reaction of monochloroacetic acid on the alkali cellulose to form an ether. The water-soluble sodium carboxymethyl-cellulose has been known in Europe for several years as sodium cellulose glycolate and has been marketed under several trade names. These cellulose ethers, however, are relatively new in North America, where the name carboxymethyl-cellulose is often abbreviated to C.M.C., or they are referred to as cellulose gum. The particular grade of Carboxel used in the settling tests in the mill of Chesterville Mines, Limited, is the high-viscosity sodium carboxymethyl- cellulose known as Carboxel H.V. It is a white, fluffy powder and is hygroscopic, although not deliquescent. Carboxel solutions in water are colourless, odourless, and resistant to beat and light. They are stable to alkalies, but are precipitated by acids when the pH is reduced below 4.0, and also by solutions of soluble lead, iron, copper, aluminium, and chromium salts. Solutions of Carboxel exhibit the properties of hydrophilic colloids.

Jan 1, 1949

The Bluebell mine of The Consolidated Mining and Smelting Company of Canada Limited extends under Kootenay lake, in southern British Columbia, and water control underground has always been a major problem. This paper gives a brief history of the operation, and then de-scribes the methods used by Cominco to keep the combination of lake seepage, ground water and thermal spring water under control. The pumping arrangements are de-scribed in considerable detail, with illustrations to show the various stages of development, and the power supply sys-tem is outlined.

Jan 1, 1966

By R. Pandher, R. Schonewille, N. Tripathi

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGE TM METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By R. Pandher, R. Schonewille

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGETH METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By Jian Deng

Rockbursts are sudden and violent failure of rocks in deep and/or high stress mines, which may destroy the excavation space and cause an accident or even the death of mining workers. This study is motivated by the pervasiveness of rockbursts all round the world. It has been found that rockbursts are often stimulated by dynamic fluctuation which is generated by mining operations or other sources of vibrations, such as blasting in adjacent stopes. This paper attempts to investigate the dynamically stimulating mechanism of pillar rockbursts in hard rock mines from an innovative point of view. Rockbursts are classified into triggered rockbursts and induced rockbursts in accordance with the magnitude of the stimulation force. Triggered rockbursts occur only when a small fraction of stress changes associated with rockbursts is accounted for by the causative excavation, whereas induced rockbursts happen where the causative factor is responsible for most of the stress changes required to produce the rockburst. By considering rockbursts as a dynamic instability problem of structures, rigorous mathematical models are set up for triggered rockbursts and induced rockbursts, respectively. By using the method of averaging and the method of eigenvalue problems, the boundaries of rockburst occurrence of a pillar are obtained for these two rockbursts. A new explanation of the failure mode of fretting or necking of pillars is given, the perturbation effect for pillar rockbursts is found, and the parametric resonance mechanism of pillar rockbursts is revealed. The quantitative relation between blasting parameters and pillar rockbursts obtained can be directly used to control the rockbursts. Contrary to conventional methods where only rock materials or rock specimen were used to study rockbursts, this investigation attaches more attention on the structural effect on rockbursts, which have strong potential applications in deep mining.

Jan 1, 2015

By Terry A. Lee

The grade of mineral resource estimates underpin all major economic considerations of mining prospects. While there are reporting requirements to satisfy when stating a mineral resource estimate, an examination of NI 43-101 style reports suggests that authors believe that there are a number of ways of addressing these requirements. As a reader of these reports, some processes are helpful and others are not so in getting a real appreciation of how realistic is the mineral resource estimate. Critical to the quality of the mineral resource estimate is how realistic is the economic mineral concentration component. In many cases, this parameter is called grade. The industry experiences increased difficulty in achieving realistic grade estimates as the sample grade variability increases. The level of transparency in a mineral resource estimate is very much a function of the competence of the author. An objective presentation of the critical data, such as grade sampling variability can assist a reader in determining if the geology of the mineral concentration is adequately understood and how realistic is mineral resource grade estimate. This paper has considered 75 NI 43-101 style reports released in the past 2 years. The review demonstrates features that were helpful in determining how realistic the mineral resource grade estimate is. If there is insufficient transparency in a report, there is a high probability that the mineral resource grade estimate will not be realistic.

Apr 1, 2005

By Lucien Piché

"IN any opportunity such as I am now given, I suppose that one should not fail to say that what the world has to offer to this year's graduates in science and in engineering is the greatest promise ever held out. High-ranking new scientists and engineers -particularly those with the Ph.D. degree -find themselves in an apparently delightful situation; the glow of attention that surrounds them and the dazzling starting salaries that are offered to them may indeed be turning their heads a bit and the attitudes of some of them are sometimes expressed with a smugness that can find its equivalent only in freshmen. On the average, however, the new graduates are, without any doubt, the best trained ever, or at least they have been the most expensive to train in the universities.There appear to be exciting opportunities for competent, well-trained and educated scientists and engineers far beyond the numbers that can be annually produced, and the demands for excellence in depth as well as in breadth of training probably will continue to increase for many years to come. The problem is visible all around us in Canada that there is much more money to buy brains than there are brains to be bought."

Jan 1, 1966

By M. Nejati, A. Paluszny, R. W. Zimmerman

A numerical method is proposed to propagate multiple discrete fractures leading to primary fragmentation in a mine that is being worked using block caving. Deformation is computed using the finite element method, fractures are represented explicitly, and the mine domain is discretized by an unstructured mesh. Bedding planes are represented by systematically varying the elastic modulus of the rock and by defining horizontal weakness planes. Fractures and matrix are represented using parametric surfaces, and tips are defined by their boundary curves. Tip advance is controlled by a failure criterion, and a criterion for propagation direction and magnitude, based on the evaluation of the modal stress intensity factors. A novel domain integral approach is applied to accurately compute stress intensity factors (K) ahead of fracture tips in three dimensions. The method does not require a structured volumetric mesh structure around the crack tip, as integration is performed over a series of virtual surface domains along the crack front. The method is efficient, as it makes direct use of automatically generated, arbitrary tetrahedral meshes, and approximates stress intensity factors (KI, KII, KIII) along each crack front using Interaction-integrals. As opposed to the JIntegral, the method does not decompose K a-posteriori, but instead uses an auxiliary field to directly compute modal K. When using this method, numerical approximations of K do not exhibit dependence on the mesh layout, and require meshes that can generally be ten times coarser than are required by displacement- and stress-based methods. Volumetric meshing requires only, on average, 17% of each computation step. Thus, cracks do not follow any pre-existing mesh structure, and the method is well suited for high-density fracture datasets. The method is demonstrated for primary fragmentation of a mine area covering 110 initial draw points, immediately beneath a 2m high undercut. Displacement is constrained at all boundaries except the surface of the undercut. The growth of the fractures is investigated at the onset of the undercut. Ninety initial disc-shaped fractures are taken into account, each having an initial radius of 10 m. Fractures grow around the undercut, intersect the bedding plane boundaries, and the domain is fragmented as a result.

Jan 1, 2015