Search Documents

By D. Karpoff

"IntroductionUNTIL the recent discovery and development of deposits at Allard Lake, on the Lower Romaine river, practically the whole of Quebec's - and indeed of Canada's - production of ilmenite had come from deposits in the vicinity of St. Urbain, Charlevoix •county, a village about eight miles north of Bay St. Paul on the north shore of the St. Lawrence, some sixty miles below the city of Quebec (see Figure l) . Although these deposits were known nearly three hundred years ago and were worked in a small way during the years 1872-74, when a charcoal blast furnace was operated by the Canadian Titanic Iron Company for making white pig iron, it was not until 1908 that more or less continuous production commenced and has •continued to the present by the American Titanic Iron Company. The whole of the output has been exported to the United States.The ilmenite occurs in lenses •and dyke-like bodies within anorthosite. Production has come chiefly from three deposits: General Electric, Furnace, and East and West Coulombe. During 1951 -52, an extensive diamond drilling programme was carded out under the direction of the writer to test the Furnace and the East and West Coulombe deposits (Figures 2 and 3), which form part of the property of St. Lawrence Iron and Titanium Mines, Limited. The average tenor of the orebodies encountered in the course of the drilling was 38.60 per cent TiO2 and, in addition to these high-grade •bodies, there was found a very considerable tonnage of lower grade ore."

Jan 1, 1953

By J. R. Gill

Introduction The property and plant of the Falconbridge Nickel Mines, Limited, is situated about 13 miles northeast from Sudbury, in Falconbridge township, near the eastern extremity of the southern Nickel Range. As early as 1899 or 1900 some work was clone on this property by the late Thos. A. Edison, when a shaft was sunk through 80 feet of overburden to within a few feet of the ore-body. At this point quicksand was encountered, which made it impossible to continue with the equipment at hand. As a result, the activities of the Edison party ceased in this section. There was no further progress until 1915 and 1916, when an extensive diamond-drilling campaign, carried out by the E. J. Longyear Company, located the ore-body that is now being worked. The property was acquired by the present operators in 1928, and in September of that year active mining development was commenced. Features Influencing Design Of Plant Early in 1929 plans were prepared for a smelter and the necessary crushing and sorting plant. In spite of the general trend towards the reverberatory furnace as a smelting unit, it was decided to erect a blast-furnace plant. The limited tonnage to be treated, of course, influenced this decision to a great extent. However, it was known that, with the proper procedure, extremely favourable results, both economic and metallurgical, could be obtained in blast furnace smelting. The possibility of very low slag losses, the simplicity of operation by the elimination of roasting plant, fuel plant, etc., the ability to handle coarse feed, and the lower initial cost, were considered factors in favour of the blast furnace. Notwithstanding the fact that we might be called on to treat a certain amount of concentrate, it appeared that the blast furnace was the proper unit for the contemplated operation.

Jan 1, 1932

By R. P. van Hille, N. Mooruth

Remediation of acid rock drainage (ARD) was performed within a linear flow channel reactor (LFCR) via a floating sulphur biofilm (FSB). A full sulphur species material balance was conducted in order to characterize the sulphide oxidation. The reactor was able to achieve an 82% and 93% conversion of sulphide with a hydraulic residence time of 2 and 5 days respectively. 92% and 55.5% of the converted sulphide reported to the biofilm as sulphur for the 2 and 5 day residence times respectively. The mass transport limitations within the biofilm were identified via a dissolved oxygen gradient profiling system.

Jan 1, 2011

By CIM CIM

Why Workplace Important! ?We need Diversity is to do more in the industry as a whole to encourage and support diversity. It has long been an industry of white dudes and we?re not going to survive if that?s how we continue to think.? ? Mark Scott, HR Superintendent, Vale Inco PURPOSE OF MINING FOR DIVERSITY ? Share best practices in the areas of HR Development ? Support industry in attracting, recruiting and retaining a diverse workforce ? Raise awareness of industry HR challenges and collaborate with stakeholders to develop sustainable HR practices

May 1, 2009

By V. A. Chanturiya, T. N. Matveeva, N. K. Gromova, T. A. Ivanova

"The research is aimed at solving the problem of increasing the extraction of gold from refractory ores, which are the main source of growth in gold production in the next decades. The purpose of the research is the development and scientific substantiation of the reagent modes for flotation extracting of gold from refractory ores using eco-friendly low-cost herbal modifiers (HM), providing increase in gold recovery and quality of gold concentrates. In the course of research laboratory techniques for the preparation of experimental samples of HM were developed, which included the sequence of operations of grinding Heraclium leaves and stems grinding, 2-stages extraction at a temperature of 50-60 °C, short-term ultrasonic treatment, filtration and subsequent unification of extracts. According to the developed method, the experimental samples of HM and conducted research were tested to analyze their sorption and flotation activity related to the extraction of gold from refractory gold ores.New data on adsorption and flotation properties of Heraclium stems and leaves extracts (HSE) in selective flotation of Au-sulfide minerals were obtained using UV-spectroscopy, scanning electronic and laser microscopy and atomic force microscopy. The dimensions and shapes of adsorbed hydrophilic films of herbal reagents were identified and mechanism of formation of stable insoluble compounds on the surface of minerals in flotation was explained.Research flotation tests carried out on samples of refractory gold ore of one of Russia deposits showed the possibility of effective use of herbal modifiers to improve qualitative and quantitative indicators of enrichment compared with the standard reagent regime. New reagent modes, using herbal modifiers in an amount of 5 to 10 ml of the extract (300 - 600 g / t, respectively) improves the quality of the concentrate: gold content attains 14.7 g / t, 1.34 times higher than in the baseline experiment and provides a gain of 3.13% extraction.The developed reagent regime with herbal modifiers is the author's original design, patented (patent of the Russian Federation) and have no analogues in the world of mineral processing. (Application number 2015116125 from 04.28.2015, ""The method of flotation separation of sulfide minerals using herbal modifier"", Russia). Actual application of new plant extracts as modifiers in flotation of sulfide minerals is the possibility of replacing of highly toxic chemical compounds by environmentally safe substances of plant origin. Implementation of the developed methods of extracting gold from refractory minerals with herbal modifiers will help to improve gold recovery at 3-5% and the quality concentrate of not less than 1.2 times, leading to higher productivity and a reduction of the negative man-made effects on the environment ."

Jan 1, 2016

By D. A. Bordin, C. J. Newman, R. J. St. Eloi

"The requirements for a metallurgical acid plant treating smelter gases are both unique and demanding in terms of sulphur dioxide treatment and emission control. Since start up in 1981, the copper smelter at the Kidd Creek Division of Falconbridge Limited has undergone several major expansions. The expansion and modification of the acid plant has been an integral part of this process. Both production demands and government regulations dictate that this metallurgical acid plant be unique in terms of operating flexibility. The variable capacity to treat a wide range of sulphur dioxide concentrations, and the operating flexibility to control emissions are the topics of this paper.INTRODUCTIONThe Kidd Creek Division of Falconbridge Limitied is a base metal mining and metallurgical complex located in Timmins, Ontario. The discovery of the original copper-zinc-silver orebody was announced in April, 1964. Mining operations began in 1966 with a 9000 tonne per day concentrator coming on stream in November of that year. In April 1972, a 108 000 tonne per year zinc plant was commissioned. Over the years the facilities have been expanded, such that the concentrator now has the capacity to process 13 000 tonnes of ore per day . To expand zinc production, the world's second installation of the Cominco/Sherritt pressure leaching facility was completed in 1983 to bring total zinc production capacity to 125 000 tonnes per year. In 1973, serious planning for a smelter operation began. In early 1975, after studying both continuous smelting and flash smelting processes, a decision was made to proceed with the technology offered by Mitsubishi Metal Corporation of Japan. The Mitsubishi Continuous Smelting Process was to be used for the smelter and the Onahama No.3 tankhouse technology for the copper refinery.The smelter, which uses the Mitsubishi Continuous Smelting Process for the continuous production of blister copper from concentrate, went on line in June 1981. It has been expanded from its original capacity of 60 000 tonnes to 100 000 tonnes per year of copper.From the very early design stages for the metallurgical complex, the company had adopted a policy of constructing and operating modern plants which would meet existing and anticipated environmental standards. With this in mind, the decision was made to utilize the proven technology of fixing sulphur dioxide emissions, in the form of sulphuric acid. A 636 tonne per day single absorption contact acid plant was built to serve the zinc plant in 1972. In 1981, an 883 tonne per day double absorption contact plant was built to serve the needs of the copper smelter. The copper smelter acid plant has since been expanded to a design capacity of 1692 tonnes per day and it is the main focus of this paper."

Jan 1, 1989

By A. M. Gaudin

Introduction The discovery of artificial radioactivity, that is, of radioactivity of acorns other than those which are naturally radioactive, has increased vastly the possibility of using radioactivity as an analytical cool. The incomparable value of radioactive atoms, which are commonly termed tracers, arises from the extreme sensitivity of this analytical method. To get an idea of this extreme sensitivity it may be useful co recall that gravimetric analytical methods will not permit the weighing of anything much lighter than one-hundredth of a milligram of material. Under the most favourable circumstances, this represents an uncertainty in the answer of 1016 acorns, or 10,000,000,000,000,000 acorns. Accurate spectrographic methods possibly have a sensitivity 10,000 times greater than this, but the uncertainty is still of the order of 1012 atoms. The tracer permits ascertainment of decay of a single atom so that its sensitivity, without half trying, can be several orders of magnitude greater than that of any other method available co chemists. In addition co the sensitivity of tracers to which reference has just been made, tracers have another property which makes them unique. A radioactive atom is almost exactly like the corresponding non-radioactive acorn m regard to its electronic structure, and therefore in regard to its chemical properties. The nucleus is different, but the nucleus does not participate in chemical reactions. Therefore, a tracer acorn behaves like an ordinary atom until such time as its nucleus undergoes a catastrophic decay. This unique property permits one to use tracer acorns as atomic spies and therefore to follow the behaviour of acorns of a certain kind among their own kind. In other words, the tracer method permits us to study and measure what we call self-diffusion. All of the uses of tracers that have been made depend on the two properties co which reference has been made.

Jan 1, 1949

By R. J. Smyth

A Steel Compression Reinforcement Repair Technique (PetroSleevel) system has been developed that has the ability to repair pipeline defects such as stress corrosion cracking (SCC) without requiring welding to the operating pipeline. The Technology has been used to repair active cracking in ERW seam and cracking in the pipe body. All repairs were performed while the pipeline was in operation. This paper will discuss the engineering theory, testing performed to verify the engineering theory, and examples of actual sleeve installations.

Jan 1, 2005

By R. D. Brown

Manitoba has now joined Ontario and Quebec in providing for new incentives and lower tax rates for the mining industry. A single rate of tax (to replace the former two-tier royalty), an investment tax credit and a relatively straightforward set of rules for calculating taxable mining profits are the main features of new mining tax legislation announced by Manitoba's Finance Minister Donald W. Craik in his May 15, 1979 budget address. On introducing amendments to reform The Metallic Minerals Royalty Act, the Finance Minister indicated that the new tax regime is intended to restore the Manitoba mining tax system to a competitive position in Canada, and should result in renewed investment in the province's mining industry. 1n this regard, the government could be right-there is little question that the new tax regime will produce greater incentives for the mining industry than the two-tier royalty system introduced by the New Democratic government in 1975. The proposed changes, contained in Bill 57, would largely be effective January I. 1979.

Jan 1, 1979

By J. M. Ortiz, J. P. Bertini

"In mineral resource and ore reserve estimation, several sources of information are generally available, such as diamond drillholes, reversed-circulation drillholes, and blastholes, and originate from one or more sampling campaigns and are analyzed by one or more laboratories. In such a situation, the grade measurements may not have the same precision and one should distinguish between hard and imprecise data.This work aims at studying the impact of data imprecision in resource/reserve evaluation through two case studies on simulated deposits: a porphyry copper deposit conditioned to real exploration and production data, and a gold deposit simulated without any conditioning data. Several geostatistical techniques are used to estimate the grades of selective mining units from exploration samples, including kriging, cokriging, lognormal and indicator kriging. Two types of imprecision are examined— measurements with multiplicative errors and measurements defined as intervals. The results are compared to the simulated grades of the selective mining units from a statistical and economic viewpoint.The study concludes that imprecise measurements should never be discarded because they help to improve the estimates, and that simple methods such as kriging are as efficient as more sophisticated ones for resource/reserve assessment. Finally, a few indications on how to diagnose and model the data imprecision are given."

Jan 1, 2005

By Q. Chen, J. H. Zhang, M. Zhang, F. M. Zheng, Y. J. Zhang

The characteristics of air bubbles and gas dispersion in KYF flotation cell are studied using the method of the point conductivity probe and CFD simulation. With increasing of speed, the velocities of air bubbles increase slowly and the distribution of diameters exhibits little change. With increasing of aeration rate, the gas holdup is increased. However, the velocities and diameters of bubbles have no great change. The CFD predictions on gas holdup have good agreement with the experiment results. The gas holdup distribution in the center section is revealed. The gas dispersion in the middle and upper part of flotation cell is uniform. It would be helpful for bubbles and solid particles collision. The gas holdup of the lower part of flotation cell is scarce, and it agrees with the observation in experiment. The gas would accumulate at the suction side of impeller blades, and it would decrease the power consumption. The rotating speed and aeration rate have great effect on gas dispersion. With increasing of aeration rate, the gas holdup of flotation cell will increase. The increasing of speed would improve gas dispersion. The results are expected to help to optimize the performances of KYF flotation cell.

Jan 1, 2015

By K. Duckworth

The treatment of Turam data by conventional procedures does not permit the interpreter to make any estimate of induced current magnitudes. This problem may be overcome by using an alternative data treatment procedure. It is shown that the conventional and alternative procedures are equally satisfactory in terms of their ability to provide the location of line currents and estimates of conductor quality. A full description and evaluation of both procedures is presented in conjunction with field examples to show how the alternative procedure may assist interpretation when used to complement the conventional approach.

Jan 1, 1973

By C. J. K. Purdy, H. E. Jamieson

"The comprehensive assessment of the environmental impacts of mining rare earth element (REE) deposits depends on a sound knowledge of the mobility of REEs in low-temperature aqueous environments. Temperature, pH and water chemistry are important factors controlling the aqueous mobility of REEs, while REEs are known to readily form complexes with both inorganic and organic ligands, and it has been shown that sorption and colloid formation may play an important part in dictating REE transport in the low temperature weathering environment. Ore and host rock mineralogy is also a key factor controlling the extent to which REEs are leached from mine waste. INTRODUCTIONThe aqueous mobility of rare earth elements (REEs) has commonly been explored in the past due to their potential application as tracers of geochemical processes in aqueous systems. REE mobility in low-temperature solutions has been shown to be dependent on the pH, temperature, ionic strength, and solution chemistry. For example, the aqueous transport of REEs can be modified by complexation with organic and inorganic ligands (Johannesson & Zhou, 1999; Klungness & Byrne, 2000; Luo & Byrne, 2004; Schijf & Byrne, 2004; Tang & Johannesson, 2010; Wood, 1990, 1993), or through sorption to suspended particles and colloids (Bau, 1999; Quinn, Byrne, & Schijf, 2004, 2006a, 2006b, 2007; Sholkovitz, 1995). Here we review the coordination chemistry, sorption behaviour and potential colloid association of REEs with respect to low temperature aquatic settings.RARE EARTH ELEMENT CHEMISTRYREEs include lanthanum to lutetium of Group IIIA in the periodic table. All share very similar chemical and physical properties. Often included in REE studies is another Group IIIA element, yttrium owing to its similar properties, and occasionally scandium, although its considerably smaller ionic radius makes for different properties and will not be discussed further here. The REEs are often subdivided into the light REEs (LREE), La to Sm, and the heavy REEs (HREE), Eu to Lu, which also usually include Y (hence are often referred to as YREE). The REE may be subdivided further into the LREEs, middle REEs (MREEs), and HREEs, in which case each classification includes La-Nd, Pm to Ho, and Er to Lu as well as Y, respectively, although definitions vary throughout the literature."

Jan 1, 2012

By David A. Edgecombre

This paper discusses modern practices in the extrusion of steel. Particular emphasis is given to a description of the Ugine Sejournet method of extrusion, involving the use of glass as a hot work lubricant. Other methods are also mentioned. A brief history of extrusion is presented; present practices in the quality extrusion of tubing and solids are described; and the future potentials of the) process as a tonnage producer are briefly discussed. The advantages of extrusion and the reasons for the use of a glass lubricant, as well as the various methods of using glass, are given. The process, as described, is being used in the manufacture of large commercial quantities of stainless steel tubing and sections. This extrusion process is an essential and unique means of forming such atomic-age materials as titanium, zirconium, molybdenum and other super alloys all of which are materials required in the creation of nuclear installations.

Jan 1, 1963

By George E. Cole

Introduction In view of the fact that, during the past year, two Manitoba mines-Flin Fion and Sherritt Gordon-have entered the list of producers and have materially increased that Province's contribution to the metal production of the Dominion, it would seem appropriate at this time to review the progress of the industry in the Province, with particular reference to the out-standing metal-mining developments of the past decade. That these two mines have been able to continue their operations in spite of the low prices of copper and zinc adds a touch of brightness to the industrial life of the Province. Depression in metal prices is not encouraging to the mining industry, but it does stimulate efficiency in methods and costs of production. As two thriving towns have grown around the two mines, the will of the management to carry-on is of great consequence to Manitoba, this year so hard hit by the .agricultural depression. And, much as it is a pleasant feature in the mining situation that these mines have been able to continue operations, nevertheless it must be noted, in reviewing the mining developments of the past few years in Manitoba, that the Province was fortunate enough to profit by good times, in that an industry was established which gives evidence of permanency. In the metallic field, the section of Manitoba that first received attention from prospectors was the boundary district, west of the Lake of the Woods. Several claims were staked here at the time of the gold boom in the neighbouring Ontario area. But the first real interest in metalliferous deposits dates from the discovery of gold in March, 1911, in quartz veins on the shores of Rice lake, some twenty miles east of lake Winnipeg. Systematic and organized prospecting of the pre-Cambrian areas of the Province may be said to have commenced with that discovery. The first gold discovery in northern Manitoba was made at Wekusko (Herb) lake in 1914. This was followed by the discovery of the Flin Flan and Mandy copper ore-bodies in 1915 on Flin Fion and Schist lakes, respectively.

Jan 1, 1932

By Rénard Chaigneau

Quality during induration Drying ??40% of energy ??Drying velocity = f(1/radius2) ??Size versus risk of condensation ??Flow is important (minimise fines)Oxidation ??IOC Fe2+ typically 0.04% ??Important to minimise Fe2+forLow Temperature Disintegration ??Tight size distribution is key13

May 1, 2011

By P. V. Amosov, V. A. Masloboev, D. V. Makarov, S. G. Seleznev, A. A. Baklanov

"The development of industry and intensive use of natural resources leads to a significant decrease in the share of reserves of rich ores, deposits of which have nearly all been exploited. Large amounts of displaced rock mass are accumulated, significant emissions of gas and dust from mining, dust from dumps and tailing pits, ingress of chemicals and toxic elements in surface and groundwater all can have negative effects on existing ecosystems and human health. Especially dangerous is the impact in Arctic regions with extreme climate conditions. The maintenance of overburden dumps and tailings dams requires significant capital and material costs. In this paper, some mining enterprises of the Murmansk region, in the Russian Federation, consider the environmental problems of the industry and propose some solutions.INTRODUCTIONThe safety of environment during the extraction and processing of minerals is a very acute problem throughout the whole world. The problem acquires a specific character in the Russian Federation. There, rather poor minerals, often existing in unconventional forms and including several mineral components are processed. The Russian mineral base has a specific geographical location; most of the deposits under operation are located in the Subarctic or Arctic regions, as well as in Siberia and in the Far East. Vast amounts of rock waste and tailings pose serious economic and ecological problems in mining regions. The operation of overburden heaps and tailings requires considerable capital and material costs. The dumps withdraw vast lands from potential commercial use. Large amounts of mined rock disturb the existing geological balance; emissions of gas and dust which accompany the mining operations, dusting of waste heaps and tailings, emissions of reagents and heavy metals into natural surface and ground waters all can produce negative effects on existing ecosystems and human health."

Jan 1, 2016

By E. Asselin, G. K. Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe(II)Fe( III)H2SO4 solution at 90 °C and 110 °C. Results from the calculation of speciation in the above solution reveal that, at both 90 °C and 110 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller VALUES (for the reversible potential of the ferric/ferrous couple. Exchange current densities of the ferric/ferrous couple were obtained and are on the order of 106 10 5 A/cm2 a t 9 0 °C and 1 07 10 6 A/cm2 at 110 °C, respectively. The Tafel slopes from the CPP method are higher than those from the CPC method at both 90 °C and 110 °C. The transfer coefficients were about 0.360.59 at 90 °C and 0.370.65 at 110 °C. Based on the exchange current densities obtained, the rate constant kc was calculated. It was found that kc at 90 °C was slightly larger than at 110 °C, especially for the results obtained by the CPC method. The average rate constants are 862.17 cm/s for CPC and 65.30 cm/s for CPP at 90 °C, and 477.69 cm/s for CPC and 63.53 cm/s for CPP at 110 °C for nominal Fe3+/Fe2+ ratios ranging from 1:1 to 1000:1. INTRODUCTIONChalcopyrite is one of the most abundant copper-bearing minerals, accounting for approximately 70% of the world’s known copper reserves (Wang, 2005). Most of the currently proposed leaching processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale, such as Activox (U.S. 5,232,491, 1993), Nenatech (U.S. 5,993,635, 1999), Dynatec (U.S. 5,730,776, 1998), AAC/UBC (U.S. 6,503,293, 2003), Total Pressure Oxidation (U.S. 5,698,170, 1997), CESL (U.S. 5,874,055, 1999) and Galvanox (U.S. 7,846,233, 2010).To date, much effort has been devoted to understanding the kinetics and mechanisms of the oxidative processes (Biegler & Horne, 1985; Córdoba, Muñoz, Blázquez, González, & Ballester, 2008, 2009; Ghahremaninezhad, Asselin, & Dixon, 2010; Hirato, Majima, & Awakura, 1987; Hiroyoshi, Kuroiwa, Miki, Tsunekawa, & Hirajima, 2004; Warren, Wadsworth, & El-raghy, 1982) or the cathode reduction reactions of chalcopyrite itself (Arce & González, 2002; Biegler & Swift, 1976; Biegler, 1977; Nava, González, Leinen, & Ramos-Barrado, 2008), by chemical or electrochemical methods. However, as the most important cathodic processes in chalcopyrite leaching systems, the cathodic reductions of ferric ions or dissolved oxygen are worth measuring due to their effects on the overall leaching rate, as predicted by mixed potential theory."

Jan 1, 2012

By Rakesh Kumar, Rajabrahma K., A. K. Verma, V. Mukesh

"In this study, laboratory investigation as well as numerical investigation is carried out to ascertain the transition from one mode to another for Semi-circular bend setup. Laboratory investigation is carried by varying the span length (s/2R); crack length (a/R); notch angle (a); and notch thickness (t). The specimen consists of cement, sand and water mixture in a ratio of 1:1:0.5 by weight and are prepared as per the ISRM standards (2014). Tests are conducted by a servo controlled universal testing machine at a strain rate of 0.2 mm/ min. The results are collected in terms of failure load, crack mouth opening displacement (CMOD) and images of crack initiation and propagation.Image analysis of laboratory tested samples shows that crack initiates at the notch tip when the notch inclination angle is 0°. As the notch angle increases (i.e. 30° and 60°) the fracture begins to initiate behind the notch tip. The direction of crack propagation in front and back side of the sample is same for notch inclination angle is 0° whereas it differs more and more as crack inclination increases. The transition represents the change in mode of failure from mode I (0°), mode II (30°) and mixed mode I/II fracture (60°).Finite element method used to find the transition based on MTS failure criterion. The inclination of notch is varied like 40, 42, 44, 45, and 50 deg and FEM analysis shows that the transition from mode-I to Mode-II take place at 49 deg. The same procedure can be extended to find the transition from mode-II to mode-III."

Jan 1, 2015

By R. E. Whitehead, G. J. Prior

"Abstract -Biotite from aplite that appears to have crystallized simultaneously with disseminated Cu-Mo mineralization at MacLeod Lake in northern Quebec yields K-Ar dates in the range 2032 ± 44 Ma to '2f1:)1 ± 47 Ma. The mean value, 2065 Ma, is some 400 Ma younger than the 2485 ± 64 Ma date obtained from a hornblende concentrate separated from a granodiorite sill that is spatially, but apparently not genetically, associated with the disseminated Cu-Mo deposit. The mean biotite date of 2065 Ma at MacLeod Lake, a K-Ar date of 2055 Ma reported from an area 50 km east of MacLeod Lake and published dates of about 2000 Ma for galenas from the Chibougamau Cu-Au ores, suggest a widespread thermal and mineralization event, in that part of the Superior Province east of James Bay, that differs from the common late Archean mineralization that is related to volcanism and metamorphic-intrusive activity.Sommaire - Les datations au K-Ar sur des biotites qui auraient cristallisé en même temps que la minéralisation disséminée en Cu et Mo dans une aplite mise en place au Lac MacLeod, au nord du Québec, s'échalonnent entre 2032 ± 44 Ma et '2f1:)1 ± 47 Ma. La datation moyenne, soit 2065 Ma, est d'environ 400 Ma plus récente que la datation obtenue pour un concentré de hornblende extrait d'un fùon-couche de granodiorite qui est spatialement mais ne serait pas génétiquement as­ sociée à la minéralisation disséminée en Cu et Mo. La datation moyenne de la minéralisation au Lac MacLeod, soit 2065 Ma, la dataion au K-Ar à 2055 Ma citée pour une région à 50 km à l'est du Lac MacLeod, de même que les datations d'environ 2000 Ma établies pour des galènes qui se trouvent dans le minerai aurifère et cuprifère à Chibougamau, suggèrent un phénomène thermique répandu qui aurait produit la minéralisation dans cette région à l'est de la Baie James, dans la province du lac Supérieur. Ce phénomene serait différent de celui qui aurait produit la minéralisation répan­ due d'âge archéen tardif qui elle serait associée à l'activité volcanique et à l'activité intrusive accompagnée de métamorphisme."

Jan 1, 1992