Search Documents

By Matt Manson

?? Current Exploration and Assessment ?? Overview of Potential Development ?? Infrastructure ?? Opportunities and Challenges ?? Renard? 1-10 kimberlite pipes and ?Lynx-Hibou? kimberlite dyke system within ?Foxtrot? property ?? 50/50 Joint Venture between Ashton (a subsidiary of Stornoway) and SOQUEM ?? Discovered 2001-2003 ?? Québec is routinely assessed as one of the top mining jurisdictions in the world ?? Agnico-Eagle Mines Ltd. Is Stornoway?s largest shareholder and a leading mine developer in Québec

May 1, 2008

Research on alternative lixiviants for gold is ongoing; however few people have looked at complete flowsheets. Alternative lixiviants are typically applied at concentrations 50 to 100 times those required for cyanidation. The higher concentrations make lixiviant recycle a vital part of the process. In addition it is no longer feasible to rely on lixiviant destruction to produce lixiviant free clean water for recycle to the comminution circuit. Ausenco has worked with Barrick to integrate reverse osmosis into the thiosulfate RIL processing flowsheet that forms the basis of the plant upgrade currently being constructed at Barrick’s Goldstrike autoclave facility.

Jan 1, 2014

By Ham. Y. M.

The corrosion behaviour of Al-B4C metal matrix composites immersed in 2500 ppm boron-containing H3B03, 0.5 M K2SO4, and 3.5% NaC1 solutions was investigated. Effects of B4C particle volume fraction on the corrosion behaviour of composites were studied using potentiodynamic polarization and electrochemical impedance spectroscopy techniques. Scanning electron microscopy was employed to study the surface morphology of the material before and after corrosion. Results show that all materials investigated are more corrosion resistant in 2500 ppm boron-containing H3B03 than in other solutions. No appreciable corrosion was observed in boric acid and sulfate solutions in contrast to an obvious pitting in NaC1 solution for both base alloy and composites. The preferential pitting sites are the interfaces of Al/Fe intermetallics for the base alloy, and the A1/B4C interfaces for the composites. Increasing the volume fraction of B4C particles in the composite decreases its corrosion resistance of Al-B4C composites.

Jan 1, 2011

By M. U. Savich

In Canadian mines, ear muffs are now an essential part of safety equipment. Because of this, a research study was conducted to investigate their efficiency. The main characteristics of eleven commercially available ear muffs were investigated in the laboratory and analyzed by: (I) a psychophysical method; and (2) a physical method. These investigations showed the following effects: head size has a significant influence on the attenuation because of a different clamping force; the amount of hair trapped between the ear muff cushion and the head decreased ear muff attenuation; attenuation and comfort are not in a causal relationship; with the use of glasses and their adapters, attenuation decreases-the adapters are not effective sound barriers; there are no great differences in attenuation with neck movement; the efficiencies of various brands of ear muffs are not equal; ear muffs with a small cushion area start serving their purpose more quickly because the force per unit area is larger; a clamping force larger than 900 g wt, in most ear muffs, does not cause an increase in attenuation; attenuation characteristics (ANSI 224.22 - 1957) of ear muffs show some correlation with physical tests. Nine ear muffs out of the eleven were tested under uniform conditions in mines. Three ear muffs were found to be the best. All three ear muff s have bands passing behind the head. The ear muff with a support strap, which improves comfort and maintains a good fit during wear, showed the best attenuation. Causes of poor attenuation are numerous: bad mounting of ear muffs on helmets, improper fitting, interferency by hair and glasses, improper wearing by miners, unsatisfactory enforcement by supervisory personnel, incomplete training of miners, etc. Results of this research have indicated that none of the ear muff s tested in this study contain all of the characteristics desirable in an ideal unit. Because of unsatisfactory ear muff attenuation in working conditions (/5 dBA), it should be a mandatory requirement that workers wear both ear muff s and ear plugs if the noise level is higher than 105 dBA (various literature recommends t io dBA). The key to the solution lies in the following: the foreman must be capable of helping and controlling miners in their task of wearing ear muffs properly; the program must be introduced to miners; and constant contact must be maintained with manufacturers.

Jan 1, 1979

By J. -M. Lalancette, D. Lemieux, C. Chouinard

"A gold bearing concentrate containing 107 g/T of gold, 9.3% copper and 706 ppm of mercury was processed at the demonstration scale for the extraction of gold and copper using a cyanide free process. The concentrate was generated through flotation to upgrade the gold and copper grade, but also showed contamination with mercury. This concentrate was submitted to the DST process demonstration plant. The concentrate was first oxidized using a fluidized bed to produce a calcine. The mercury was volatilized during the oxidation stage with an efficiency higher than 98%. The mercury was condensed and removed from the sulfuric acid using a thiosulphate process. Copper was extracted from the calcine as copper sulphate using diluted sulfuric acid. The solid remaining after acid leaching was submitted to the DST chlorination process for gold extraction. Under optimized conditions, a gold extraction of 97.3% was achieved in the chlorination reactor. Gold was recovered from the pregnant brine by precipitation on silica using a DST proprietary process.INTRODUCTION Dundee Sustainable Technologies Inc. (DST) offers proprietary metallurgical processes for the treatment of material from the mining industry. DST processes enable the extraction of precious metals and for the removal and stabilization of contaminants, such as arsenic, from ores and concentrates. DST provides environmentally-friendly, viable and efficient processes, capable of handling complex and refractory ores which cannot be processed with conventional approaches due to metallurgical issues or environmental considerations. Several mining jurisdictions around the world have banned or restricted the use of cyanide. DST has developed a closed loop chlorination process as an alternative to the conventional cyanidation process for the extraction of precious metals from minerals. The tailings from the process are inert from toxic substances such as cyanide and organic compounds, are sulphide depleted which means they do not generate acid, and thus, meet and/or exceed environmental norms. The process has demonstrated excellent gold recoveries within a fraction of the time needed for cyanidation to obtain similar results. Moreover, the closed loop process does not generate any liquid effluent and does not consume much water: it only requires a water make-up to compensate for moisture leaving with the tailings and by-products, and seawater may be used. The improved environmental footprint of the DST process has been certified by the Environment Technology Validation program (ETV) which provides an independent evaluation of the performance claims of innovative technologies."

Jan 1, 2017

By Navid Bahrani

Overview ? Case history of footwall slab failure ? Procedure used to build a finite element model ?? Pre- and post- mining topography ?? Slab geometry ?? Excavation stages ?? Input parameters ? Finite element modelling results ?? Unloading-induced displacements (magnitudes & directions) ?? Calibration of overall model using measured prism displacements ?? Shear stresses and displacements along the base of slab ?? Factors of safety at different stages ?? Effectiveness of rock bolts ?? Staged or unstaged model? ? Conclusion

May 1, 2008

By Stephen G. Mlot

Technical Study Work ?Technical study work enables informed decisions: -Obtain a higher price for a quality asset -Minimize expenditure on a project that won?t provide adequate returns -Optimize expenditure on a project to capitalize on the potential return

May 1, 2013

By Daniel D. M. Adams

In 2004, Rio Tinto started a major project to implement Mine Monitoring and Control (MMC) systems worldwide. A detailed selection processes was undertaken and migration to a standard system was started. Today systems are operating around the world and serve as the core of to many business processes. Implementations include highly union areas, large mines, centrally managed mines, and remote areas. Each implementation has unique challenges but all are working towards the common goal with common systems. This paper reviews two projects that Rio Tinto has deployed in diverse conditions. The projects are the Rossing Uranium upgrade from the original Wenco system to the common standard and Iron Ore of Canada?s general technology upgrade. Also discussed is the future of mining at Rio Tinto, specifically the drill automation projects, and how it is utilizing the common standard MMC systems.

May 1, 2010

By Denghong Wang

Abstract- The Ashele Cu-Zn deposit is a recently discovered volcanogenic massive sulfide deposit in Xinjiang, China, hosted by Lower to Middle Devonian submarine bimodal volcanic rocks. The primary ores of this polygenetic deposit are represented by massive syn-depositional pyrite, chalcopyrite, and sphalerite, and were formed by submarine exhalation. Hydrothermal alteration consists of strong sericitization, chloritization, silicification, and carbonatization of the metavolcanic rocks beneath the massive orebodies. Depletion of Na2O is an obvious chemical change in the hydrothermal halo. Geological and geochemical evidence suggest that the Ashele Cu-Zn massive sulfide deposit was formed by submarine exhalation related to bimodal volcanic rocks, trapped in a rifting basin, then deformed by shearing, and thermally metamorphosed by the intrusion of dacitic porphyry. Sulfur and lead isotopic studies indicate that metals such as copper and zinc may have originated from spilites, but that volatile components, especially sulfur, were derived directly from submarine volcanic magmas.

Jan 1, 1999

By Jeffrey S. Loen

"Abstract - The size, morphology, surface texture, per cent mineral inclusions, and bulk chemistry (Ag and trace elements) of placer gold particles vary systematically according to transport distance from source rocks, as indicated by a case study from the Pioneer district in Montana, and data from the literature.Placer gold samples show a rapid decrease in mean and maximum particle length, and a gradual increase in flatness index (F.I. = length + breadth/2 X thickness) from about F.I. = 2 in bedrock deposits, to as much as F.I. = 45 over transport distances of several tens of kilometers. Primary mineral inclusions (mainly quartz, sulfide minerals, and iron oxides) are mostly lost within 10 km to 20 km of fluvial transport; this loss of quartz and trace metals causes a major change in bulk chemistry of placer gold samples. Following the loss of inclusions and the development of flakes, edges of flakes are folded and the mean number of folded edges in a sample increases with distance. When viewed under the electron microscope, surface textures of placer gold particles also become progressively more pitted with distance.Analysis of placer gold particles can be used to help evaluate placer source-area problems (placers with no known hard-rock gold deposits). For example, coarse placer gold containing abundant inclusions indicates a proximal source. On the other hand, an abundance of thin flakes is evidence of a long transport distance and possible reworking from older gravels. Placer gold characteristics can therefore provide information on distance to mineralized source rocks."

Jan 1, 1995

By D. Auerswald, M. Kotze, V. Yahorava, T. Udayar

Uranium can be recovered from lower grade uranium ores (<800 mg/kg U3O8), leach residues, and waste dumps cost-effectively via resin-in-pulp (RIP). Using this technology, no solid/liquid separation or washing of the leach residues are required. Furthermore, the uranium recovery can be higher than with conventional methods. RIP technologies have, however, been perceived negatively due to concerns around potential resin fouling and losses. This paper highlights the advancements made in RIP and discusses a number of potential applications where the technology could deliver economic and consequential environmental benefits by reducing the uranium levels in the waste.

Jan 1, 2014

By C. Liu

Zeta potentials and settling rates of an oil sands tailings sample taken from Syncrude Canada Ltd&apos;s Aurora Stacker Pilot Operation were studied. Two clay minerals, kaolinite and illite, were also studied since these are the major constituent minerals in the fine oil sands tailings. Process water, decanted water as well as distilled water were used. It was observed that the zeta potentials of the tailings solids showed maximum negative values in process water at pH 8-10, which coincides with the pH of commercial hot water bitumen extraction process. The settling rates of the tailings sample were very low, at 0.008 m/hr in decanted water and 0.04 m/hr in process water. The rates were increased to 1.0 m/hr in decanted water and 0.13 m/hr in process water at an addition of 50 g/t Ciba AF1235. Although the settling rate was higher the supernatant was cloudier in decanted water than in process water. Further increase in the dosages of Ciba AF1235 did not increase the settling rates in decanted water but gradually increased it in process water, reaching 0.46 m/hr at 100 g/t. The results indicated that lower concentrations of Ca2+ and Mg2 (in decanted water) benefited settling rates but did not benefit supernatant clarity. Test results also indicated that Ciba AF1235 caused selective flocculation of the tailings sample, since the top sediments had higher illite and lower quartz contents than the bottom sediments.

Jan 1, 2006

HIGH LAKE PROPERTY --HISTORYHISTORY -19501950??s ??Kennarctic Exploration discovers Exploration sulphides (A/B & (D Zones) at High Lake during helicopter reconnaissance exploration program.- -1991 93 Aber signs agreement to earn in to the High Lake Property from Kennecott. 63 holes drilled, primarily testing the known deposits. -2001 Wolfden purchases 100% interest in High Lake from Kennecott and Aber -2002 Wolfden performs helicopter borne TEM Survey over the High Lake Greenstone Belt. -2003 West Zone was discovered following UTEM & Gravity Surveys (performed by Teck Cominco ) over an airborne anomaly approx. 1km west of the known deposits. -2004 Wolfden awarded Bill Dennis Prospector of the Year

May 1, 2006

By Paul Ransom

Sullivan Production and Present Value ? Mined 150 million tonnes ? 6.0% Pb, 5.5% Zn, 2 opt Ag, + Sn, Cd, In ? May 2006 Value + US$43 Billion ? 50% of metal from first 37% (55MT) of tons ? True original size ~ 110-120 Mt @ 17%Pb+Zn ? 30MT unconsolidated fill + HW cave

May 1, 2006

By L. H. McKay

Tailing Dams Three types of dam have been structed to impound tailings from the Allenby mill: 1.- By classifier unit 2.- By earth dam 3.- By direct deposition of tailings The first type, which includes two dams, was built across a shallow valley which sloped down to Similkameen river, just below the mill site. Two earth embankments, one below the other, were built across the valley. Tailings were then piped to Akins classifiers mounted on wooden wheels. The classifiers were set up at one side of the valley and gradually moved ahead on the sand embankment created by the sand discharge from these classifiers, the slime overflow going to settli.ng ponds formed by the dams. Decanting wells were built in the settling ponds by placing four six-by-six timbers vertically in the ground, two feet apart, to which two-by-six tongue-and-groove boards were nailed. The elevations of the ponds were raised, as required, by nailing additional two-by-six boards on the well and bolting on more six-by-six timbers when required. The bottoms of the wells were attached to a covered launder made of three-inch lumber laid on a one per cent grade. This launder carried the overflow through the dam. The second type of dam was built across a long, narrow valley, known as Hitchen&apos;s Flat, the upper ~n d of which was about 2½ miles north of the mill. This valley, an ideal tailings site, was 4,000 feet long and from 600 to 800 feet wide. An earth embankment with a concrete spillway through the top was built approximately 28 feet high across the lower end of this valley. Tailings were then dumped into the upper end of valley, with no further expense until the basin was filled up to the level of the flume where this entered the valley. When the upper end of the valley was filled to this point there was still room for more tailings at the lower end. Therefore, a pump was installed to elevate the tailings to build a wall around the upper end of the valley by depositing sands from a launder built up on 20 foot supports and sloping both ways from the pumping station around the upper end of the basin.

Jan 1, 1950

By W. J. Wright

Summary Statement The following notes on the geology of the Grand Lake coalfield are intended to be introductory to a second paper being read at this meeting, which paper will describe the earlier and the more modern mining methods. The coal industry of the Grand Lake coalfield is centred chiefly within a three-mile radius of Minto, but minor operations are dotted over an area of approximately 50 square miles extending easterly to the vicinity of Chipman and Coal Creek (see Figure 1). The coal comes from one seam of Pennsylvanian age. The seam varies in thickness from 16 to 30 inches and lies almost horizontal at depths of 0 to 125 feet. It has been mined and prospected over an area of approximately 150 square miles, but in a portion of this area the commercial possibilities have been destroyed by erosion. The industry is the oldest of its kind in North America, but it did not at tract particular publicity until about 1914. Since that date, mining methods have improved and the output has rapidly increased until, in 1934, it amounted to 271,335 long tons, and furnished employment for about 1,000 men (1). Approximately 73 percent of this amount was produced by the Minto Coal Company, the Miramichi Lumber Company, the Avon Coal Company, and Welton and Henderson, and 25 per cent by the Rothwell Coal Company, Harvey Welton Limited, G. H. King, the Reade Construction Company, and the Newcastle Coal Company. The remainder was produced by J. W. Carter, G. D. Crossman, T. H. Swift, C. S. Yeamans, and several other small operators. The coal is won by underground mining, except in the case of the Reade Construction Company, and a minor operation by Ashfield and Pieton, who have employed open stripping. It is mined only as required to fill definite orders, and is loaded directly into cars for shipment. In 1934, the larger mines did not operate full time, and the production could easily have been increased if markets had been available. The coal is sold in four grades: screened or lump, run of mine, slack, and stripping. The chief market is with the railways and commercial plants, with a fair amount for domestic purposes.

Jan 1, 1935

By Craig Dirk

Agenda Applications of ?GPS ?Drill Navigation ?Cycle time monitoring ?UDS / Boom Stress monitoring ?Payload systems ?Laser Surveying Future Applications

May 1, 2006

By C. O. Campbell

THE recognition by C. W. McKee, field engineer for Springer Sturgeon Gold Mines, Limited, in the fall of 1940, of the economic possibilities of a small outcrop of baryres near Pembroke, in Hants county, Nova Scotia, followed by aggressive exploration and development by the Company, has placed Canada for the first time in its history in the position of becoming a major producer of barytes and its products. In past years, production of this mineral in Canada has been unimportant. Thus the coral output from 1885 ro 1933, inclusive, amounted to only 41,027 short tons, following which there was no production until 1939. Deposits in Nova Scotia, and particularly in the Lake Ainslie district, Cape Breton, have been the main source of supply, with a production between 1866 and 1925 of 31,689 tons. Following the examination of the outcrop of baryres near Pembroke by Mr. C. W. McKee in October, 1940, the area surrounding it was trenched, and, as this work gave encouraging results, a diamond drilling programme was commenced. A grid system was laid our and sixteen holes aggregating 2809.3 feet were put down, spaced at 100-foot intervals, the deepest hole being 300 feet. This drilling outlined a body of high-grade baryres over 600 feet long and 200 to 250 feet wide, with an average depth of 120 feet and estimated to contain well over one million tons of ore. The limits of the body were reached on the west, north, and southwest, but the drilling was suspended before the eastern limit was determined. Quarrying operations, and construction of a 100-ton mill, were commenced in February, 1941. The mill was placed in operation on May 29th, and on June 15th, eight months after the initial discovery, the first shipment of 2,500 long rons of milled baryres was made to Trinidad, British West Indies.

Jan 1, 1942

By Brian Rausch

Agenda ?? Refresher: Victor Project Execution ?? Operations Capability roadmap: ? Operations staffing starter group: design participation ? Operations staffing build up for production start-up ? Training and commissioning integration ? Turning OPSCAP ramp-up into a project ?? Go Live! The Results

May 1, 2009

By G. M. Mason

History Due to its strong affinity for oxygen, aluminium as an element was isolated only after many other rarer metals had been prepared and studied. It was just over one hundred years ago that two scientists, Hans Christian Oersted and Friedrich Wohler, produced the first few pellets of aluminium and determined its physical properties. These early investigators used metallic potassium as a reducing agent. Later, St. Claire Deville, by using sodium instead of potassium, improved the yield in the reduction and produced some pounds of aluminium. From a figure of about $110 per pound in 1855, the price had fallen to about $4 per pound by 1886. In that year, a very important discovery was made independently by Charles Martin Hall in Oberlin , Ohio, and Paul . Heroult in France. Stated in its simplest terms, the discovery of Hall and Heroult was that aluminium could be produced by electrolyzing a solution of the oxide in molten cryolite. The application of the Hall-Heroult process made the metal immediately available in commercial quantities and, by 1900, the price had fallen to 23 cents per pound. The growth of the industry in the past fifty years is well known, and is outside the scope of this paper. It is, perhaps, not generally known that aluminium was first produced in Canada at Shawinigan Falls in 1901. Since that time, production has been continuous at one or more smelters in the Province of Quebec. The largest of these smelters, which is also the largest aluminium smelter in the world, is at Arvida, Quebec, on the Saguenay river. A large power potential and access to ocean shipping were the two principal reasons for the establishment of aluminium production facilities in the Saguenay district. It is interesting to note that the aluminium industry, as a large user of power, took an active part in the early industrial development at Niagara Falls and Shawinigan Falls, and is now repeating the process in the Saguenay valley.

Jan 1, 1949