Search Documents

By W. Standifird

"Cohesive fracture is a mechanical model widely used for modeling quasi-brittle fracture in rocklike materials. This work discusses use of this model to simulate quasi-brittle fractures generated by injection stimulation during the process of cuttings reinjection in West Africa. Cuttings reinjection is an engineering practice used for disposal of drilling waste. During this process, hydraulic fractures are created at the target formation and milled cuttings are injected with fluid. In practice, this process must remain in compliance with environmental regulations and zero-discharge policies. The purpose of this study is to determine the following factors of injection design for a field in West Africa: (1) pumping pressure capacity required to successfully perform the injection and (2) the injection rate for injection performance and the value of fracture width under injection.A simplified three-dimensional (3D) finite element model (FEM) was built. A poroelastic plastic damage model was used for simulation of the cohesive crack prorogation within the target formation. For simplicity, fracture development in both horizontal and vertical directions was simulated separately. In this way, the computational burden for one calculation was reduced to a reasonably low level, without losing accuracy of the model. Loads of the model include fluid injection and gravity, which balances the initial geostress field. Various values of injection rate were used in these calculations to determine the most reasonable value of injection pressure. The capacity of pressure of a pumping device was determined using this optimized value of injection pressure.Results in values of width and length of fractures created by the injection are presented. Injection pressures at bottom-hole (BHP) corresponding to each value of injection rate are also given. Numerical results for fracture generation and propagation in a horizontal direction were visualized. The pumping pressure capacity required to fulfill the cuttings reinjection work was determined based on the numerical results of optimized injection rates and pressure. The fracture width was determined using the given pumping pressure. The length and height of the fractures was determined using pumping pressure along with the required volume of cuttings waste to be disposed of into the formation.This work presents a case study of 3D finite element modeling of hydraulic fracturing generated by cuttings reinjection. The results of the optimized injection rate and pressure provide a best practice and a useful reference for cuttings reinjection analyses in this region."

Jan 1, 2015

By L. McFarlane, D. Rollwagen

"Madawaska Mines produces a uranium precipitate (83-85% u3o8) using a magnesium oxide slurry to precipitate the uranium from solution. The solution, at approximately 9""0 g/l u3o8 is neutralized to a pH of 7.0. At the Eldorado Nuclear Refinery in Port Hope, the precipitate is not acceptable as a single feed to the refinery process. It was discovered that a 2% silica impurity caused emulsion problems in the solvent extraction column.After extensive studies of possible solutions, such as two-stage precipitation and solvent extraction, an acceptable solution was found. The selective precipitation of uranium at a pH of 3.5-4.0 using Hydrogen Peroxide produces an almost silica free product of higher purity (90-93% u3o8) to that of straight magnesium oxide precipitation. Introduction Madawaska Mines Limited is located four miles southwest of Bancroft, Ontario. The annual production of u3o8 is approximately 610,000 pounds. To produce the final product or yellowcake, nine separate steps are required. These are (1) grinding, (2) dewatering, (3) leaching, (4) acid filtration, (5) clarification, (6) ion exchange, (7) precipitation, (8) washing, and (9) drying and packaging. To illustrate these steps, a complete flowsheet of the mill is displayed on page three.The yellowcake is sent to Eldorado Nuclear Limited in Port Hope, Ontario for further concentrating and refining. As part of their routine specification check, a test called the amenability test is performed. This test indicates how a particular dissolved yellowcake product reacts to solvent extraction. The Madawaska yellowcake did not pass the test."

Jan 1, 1982

By S. Banisi, J. A. Finch, A. R. Laplante

"A technique for on-line simultaneous estimation of gas and solids holdup (volume fraction), based on a combination of conductivity and pressure difference measurements, is proposed and tested in a laboratory flotation column (10cm in diameter and 447cm in height). Fundamental concepts underlying this technique and the effect of relevant parameters are discussed. In the studied range, 3-30 %v/v gas holdup and 2-18 % v/v solids holdup, experimental results showed good agreement between the estimated and actual holdup values (as determined by an isolating technique). The relative accuracy of the solids holdup estimation increased when solids density or solids concentration increased. Frequent re-calibration of pressure transducers was found necessary for accurate phase holdup estimation.IntroductionGas holdup is a key parameter in controlling the performance of flotation columns. For example, flotation rate is affected by bubble size and gas rate both of which, in turn, affect gas holdup. Moreover, gas holdup also determines the slurry residence time which indicates a direct influence of gas holdup on recovery.Gas holdup determination has been the focus of many studies (e.g., Castillejos, 1986; Marchese et al., 1992). Some of the techniques which have been used are given in Table 1."

Jan 1, 1994

By Robin Sheremeta

Fording Greenhills first acquired GPS (Global Positioning System) technology with the commissioning of a GPS-based dispatch system in December 1994. The second exposure to satellite technology came with the conversion of the conventional optical survey system to a high-resolution GPS system in June 1995. In September 1995,a GPS-based grade control system was tested on the largest shovel (Marion 301 — 58 cubic yard).In January 1996, the system was added to all of the cable shovels (2 P&H 2800s). All three applications of GPS at Greenhills are fully operational and producing positive results. This paper will focus on the practical application of GPS in a mining environment and the effect that GPS technology has had on the Greenhills Mine.

Jan 1, 1996

By R. Simon, A. Khosravi

"Tensile strength of rock samples is measured by direct and indirect tensile tests in accordance with standard guidelines. Due to the difficulties in performing direct tensile test, the indirect tensile (Brazilian) test is conventionally carried out to obtain the ultimate tensile strength. A limited number of studies have been conducted to investigate the role of sample size (length to diameter ratio = L/D) in the stress distribution of the Brazilian test using numerical and analytical methods. These investigations showed that the tensile stress distribution along the loading diameter is not uniform. They also indicated that the difference between the tensile stress at the middle part and at the sides of the sample with higher L/D ratio is greater than that in the other samples.The objective of this study is to show the effect of tensile stress distribution on the fracture surface created by the Brazilian test from a morphological point of view on the samples with different L/D ratio. Hence, a series of fracture surfaces created using the Brazilian tests on the rock samples with L/D of 0.5, 0.75, 1, 1.25 and 1.5 were investigated.In this study, all fracture surfaces were scanned by a 3D laser profilommeter. A number of roughness profiles parallel and perpendicular to loading axis have been selected from the samples with different L/D ratio and spacing of 1 mm. The results show that the roughness of the profiles perpendicular to the loading axis increases with an increase of L/D ratio, while the roughness of the profiles parallel to the loading axis decreases. Furthermore, some roughness profiles parallel to the loading axis were chosen and divided into three segments. The results revealed that the segment in adjacent to the upper loading platen possesses higher roughness than the other segments."

Jan 1, 2015

By L. C. Johnston, J. N. Gills

This paper reviews the basic reactions of the blast furnace and the open hearth furnace, and then discusses the quarrying and sizing requirements of the limestone feed for each. Particular emphasis is placed on the lime-stone at Irish Cove, now being mined under an agreement between Scotia Limestone Limited and Dosco Steel Limited. The drilling and blasting operations are described, along with loading and haulage, plant flow, water supply, power supply and transportation facilities.

Jan 1, 1967

By G. A. Peebles

"This paper describes the various types of radiometric instruments and the techniques of their operation for grade control, sampling, assaying and probing drill holes at Eldorado Nuclear's uranium mine in northern Saskatchewan. Modifications that have been made to these instruments are discussed, and suggestions are made for the development of more refined and specialized radiometric equipment."

Jan 1, 1969

By T. T. Wang, T. H. Huang, S. S. Zhan

"Fractures with diverse features dominate the hydraulic behavior of fractured rocks and are one of the major subjects for hydrogeological characterization of a site. This study investigates curve patterns obtained by packed tests, and as well the influence of fracture features based on 59 sets of in situ packer tests with different fracture combinations and fracture features. The result shows that, in the example of Heshe site, neat and tidy fractures usually provide stable channel for water flow during testing, and the hydraulic properties of fractures infilled with breccia and mud may change during testing because of leaching and/or washed out of infilling breccia and mud. Different combinations of fractures with diverse features in packed test sections lead to different curve patterns for in situ hydrogeological tests. For groundwater flowing predominately through neat and tidy fractures, the pressure-discharge curve of modified Lugeon tests are usually linear curve pattern, and the pressure decrease while the discharge increase in pressure-discharge-time curves of single-hole double packer tests, which benefit statistically determining the transmissivity of dominant fracture sets. INTRODUCTIONFractures interlaced in rock masses are major channels for groundwater flow and generally account for the anisotropic and heterogeneous characteristics of permeability for fracture rocks. To describe reasonably the permeability of a fracture rock, the Discrete Fracture Network (DFN) approach and others with similar ideals have been developed. Many methodologies and associate equipment, for instance, the televiewer and the in situ hydrogeological test, have been proposed to investigate the spatial distribution and the transmissivity for different fracture sets, which are two main parameters necessary for the DFN or similar model simulation (Pearson & Money, 1977; Barker & Black, 1983; Hsieh et al., 1985; Bernard et al., 2006; Quinn et al., 2012). However, diverse outlooks for the pressure-discharge curves and the temporal pressure and associate temporal discharge curves often confuse the investigation results by significant deviations on derived permeability (Houlsby, 1976; Zlotnik, 1994; Royle, 2009; Camilo, 2010).Aiming on technical development for in situ hydrogeological tests and fracture investigation, an experimental well site with 10 wells has been established in Heshe in central Taiwan since 2011 (Wang et al., 2011; Song, 2012; Zhan et al., 2013). Extensive geological survey and well-hole scanning by a televiewer provide spatial distributions and outlooks of fractures in detail. Additionally, a series of Lugeon tests, double packer injection tests and pumping tests have been performed to investigate the permeability of fracture rocks, and dominate fracture sets as well. Based on the results obtained from the Heshe site, this study classifies the curve patterns of hydraulic packer tests. The features of fractures involved in packed sections for packer tests are then inspected in detail. Relationship between the curve patterns of hydraulic packer tests and associated features of corresponding fractures in rock are discussed and addressed accordingly."

Jan 1, 2015

By Graham A. Davis, Michael Samis

The dramatic fluctuation in metal and energy prices in the last few years is causing mining companies to consider alternative analytical methods for mine design and valuation. The goal is to improve insight into unforeseen changes in the economic and project environment and to design projects that take advantage of management's ability to respond to these changes. Such flexibly managed projects will contain value that cannot be measured using traditional engineering economic approaches, further motivating the used of alternative, modern valuation methods. This paper considers the valuation of an uneconomic low-grade resource at an open pit gold mine using two of the most popular modern valuation methods, Dynamic Discounted Cash Flow and Real Options. Our analysis demonstrates that the conventional valuation method may incorrectly represent the value and risk attached to mining this type of resource because it is unable to recognize management's ability to respond to future events in a manner that minimizes losses and exploits advantageous business conditions. The results of this paper highlight the importance of recognizing flexibility and business uncertainty in both mine design and valuation.

Jan 1, 2003

By K. Hanumantha Rao, A. Javadi

Our recent studies revealed that the sulfide minerals in contact with water during grinding produced hydrogen peroxide (H2O2) where the amount of H2O2 production by the minerals found to be in the order of pyrite > chalcopyrite > sphalerite > galena. The H2O2 effect on the oxidation of pulp components and its influence on the concentrate grade and recovery in flotation have been studied and the results have been presented and discussed in this paper. Studies have also been carried out to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp and as well of controlling the formation of these species through known chemical means for depressing the generation of the oxidant. Flotation tests using a complex sulfide ore with the same reagent scheme that is being used at Boliden concentrator in Sweden but with the addition of i) collector and depressant, ii) Na2S reductant and iii) inorganic (EDTA) and organic (TETA) surface modifiers, during grinding stage have been performed to judge the beneficial or detrimental role of H2O2 on the selective flotation of sulfides. The results demonstrate that the selectivity of metal sulfides against pyrite increases with increasing generation of H2O2 in the pulp liquid. H2O2 is also found to be a better oxidant in chalcopyrite-galena flotation separation than the commonly used K2Cr2O7.

Jan 1, 2016

By J B. Maughan

Gas and oil seeps have been known in Quebec for more than one hundred years. These occur in three main areas which contain sedimentary rocks with a total thickness estimated to vary from 6,000 to 20,000 feet. The strata in these areas are similar in many respects to those in producing areas of southwestern Ontario and the Appalachian basin, and the prospects for finding and developing commercial reserves of oil and gas in Quebec would therefore also appear to be favourable. Little of the exploratory drilling to date has been con-ducted in a systematic manner, and most of the drilling has utilized improper or inadequate equipment. Many wells have also failed to adequately test and fully evaluate the principal zones of interest. Relatively high drilling costs have hindered systematic exploration; however, with improved portable equipment, it is expected that future wells can be drilled with greater efficiency and at less cost. Most of the mineral rights in Quebec are held by the Provincial Government, and acreage can still be leased in large blocks on favourable terms.

Jan 1, 1964

By G. W. Poling, E. M. Coelho

"Sedimentary phosphate ores make up approximately 87% of the world's known reserves and are generally more difficult to beneficiate than igneous ores. In almost all cases, desliming prior to flotation represents the major source of losses. Laboratory studies of selective desliming of sedimentary ores are presented. Some fundamental studies with pure mineral systems are also discussed. Selective desliming, especially using selective flocculation, gave the best performance. Possible industrial applications of this selective flocculation-flotation procedure are discussed.IntroductionPhosphate ores are a major source of raw materials used in inorganic fertilizers (which supply nitrogen, phosphorus and potassium). Approximately 96% of the total world production of phosphate is utilized in the fertilizer industry. Reserves and production data are available in the literature. Today deposits with grades as low as 4% P2O5 are exploited in a few cases. However, in some northern African deposits, ore grades are still as high as 33 - 35% P2O5. Hout pointed out in 1982 that approximately 200 million tonnes of phosphate ore were upgraded by flotation only.Although there is a large number of phosphate minerals (over 300, only those in the apatite series are important ore minerals in phosphate ores. The most common member in this series is fluorapatite – Ca5(PO4)3F. However, in sedimentary phosphate rocks, many different substituents occur in the apatite lattice. Carbonate-fluorapatite (or francolite) is one of the most common names used to describe sedimentary apatites. It can be represented by the empirical formula:"

Jan 1, 1986

By Osamu Inoue, Takashi Yamashita, Takashi Ikemoto

The expansion project in Naoshima smelter and refinery to meet enhancing recycling business of E-scrap was successfully completed in 2016 to have a capacity of 110,000 tpa of E-scrap treatment. Increasing treatment of E-scrap has raised the Ni content of copper anode to 4000 ppm on average, which is double the level of 10 years ago, and to 6000 ppm or more occasionally. The tank house has refined such copper anode to copper cathode with starter sheets. Since most Ni in Copper anode dissolves in copper electrolyte, the Ni content of the electrolyte has increased to 27 g/L and more. Ni accumulated in the electrolyte has increased power consumption during the electrolytic refining of copper, although cathode quality has been controlled satisfactory so far. In order to ensure sustainable operation while growing E- scrap business, the NiSO4 process has been expanded recently so as to recover Ni in the electrolyte more and the pressurized-leaching technology will be introduced to the slime leaching process so as to enhance the capacity of slime treatment and to improve Ni recovery in the near future. INTRODUCTION In recent years, the treatment amount of E-scrap at Naoshima smelter and refinery has increased according to the growth of its recycling business as shown in Figure 1, while impurities from E-scrap have concentrated in copper anode as well. Especially, Ni content in anode has been increasing remarkably since 2012, causing to raise Ni content in the electrolyte as shown in Figure 2. The increment of Ni content in copper anode and electrolyte has adversely affected the electrorefining process, slime leaching process, and NiSO4 crystallization process at the tank house. Such severe conditions provided opportunities to redesign the tank house to establish a robust process to which more Ni is acceptable.

Jan 1, 2019

By J-F. Béland, N. Parson

Aluminum extrusions are widely used for automotive crash management systems due to their superior specific energy absorption capabilities, as compared to steel. The Al-Mg-Si alloy series can be readily extruded into complex multi-hollow profiles, as required in crash systems, and can be used to target a range of desired strength levels. This paper focuses on the development of an axial crush test protocol and evaluation of the crush performance of common 6XXX series alloys for a variety of tempers. The observed crush behaviour is then compared to tensile test results.

Jan 1, 2015

By M. E. Hurst

Introduction Between 1903 and 1905, W. Mclnnis, of the Geological Survey of Canada, made a micrometer traverse of the Kawinogans (Crow) river from Kapkichegimaga lake to its junction with the Otoskwin river. He reported that a belt of Keewatin rocks, 1 to 4 miles wide, was exposed along the course of the river for 17 miles east of Kapkichegimaga lake. Prospectors and exploration companies paid little attention to the mineral possibilities of this belt until the summer of 1928 when, with the adoption of airplane transportation, the area became readily accessible. Within a short time widespread interest was aroused by the announcement of attractive finds, and a mild rush followed. During the winter months, hundreds of claims were staked on either side of Crow river for 12 miles east of Pickle lake. In the summer of 1929, much of this ground was systematically explored and a considerable amount of development work was done on the known deposits.

Jan 1, 1930

By C. H. B. Leitch

"The Bralorne-Pioneer deposit produced more gold than any other deposit in British Columbia over its 70 years of operation (130 kg or 4 million oz of Au, from 7 million tonnes of 18 glt ore). Mineralization is related to a suite of late Cretaceous albitite dykes of 85 to 90 Ma age. It thus occurred long after and is genetically unrelated to the Early Permian (275 Ma) Bralorne diorite and soda granite.The major veins strike about 110 degrees and dip north at 70 degrees, with slickensides plunging 45 degrees east that indicate last movement was reverse. Major ore shoots in the veins occupy somewhat less than 20% of the vein and plunge steeply west, roughly perpendicular to the slickensides. The structures that contain the veins probably formed at around 95 to 90 Ma during a strike-slip episode with easterly directed maximum compression.Disseminated pyrite, pyrrhotite, and minor chalcopyrite occur within envelopes up to several metres from the veins. Arsenopyrite is confined to vein selvages. Local sphalerite and galena appear to correlate with gold-rich portions of the veins. Traces of tetrahedrite and stibnite have been observed but tellurides have not. Gold is found principally as thin smeared flakes of the native metal in the black sulphidic septae of the strongly ribboned veins. Hydrothermal alteration envelopes around the veins grade outwards from intensely foliated quartz - ankerite - sercite (±fuchsite) to less sheared calcite - chlorite - albite to unsheared epidote -calcite.Open-space vein filling textures found in the deep (mesothermal) environment at Bralorne can be explained by a fault- valve model. High-angle reverse faults may have acted as fluid-pressure activated valves on geopressured reservoirs, causing large cyclic fluctuations in fluid pressure that promoted mineral deposition in an episodic fashion . The faults that were mineralized were reactivated sub-vertical former strike slip faults, oriented at a high angle to the northeast-directed stress in a compressive regime."

Jan 1, 1990

By D. F. Sangster

"Eight volcanogenic massive sulphide districts in Canada and Japan, ranging in age from Archean to Miocene, were selected for analysis. The study revealed that: {I) each district has an average diameter of 32 km; (2) the districts contain 4 to 20 deposits each, with an average of /2 deposits; (3) the average total base metal content per district is 4.6 million tonnes, with a coefficient of variation of32%; (4) ranked in order of size, the largest deposit in each district contains, on average, 67% of the total metal and the second largest about 13 %. The remaining deposits range downward in decreasing proportions. Empirical observations such as these may be used f or evaluating the undiscovered potential of new districts as well as contributing to a better understanding of the distribution and genesis of this important class of base metal deposits. Previous WorkThe characteristic geological features o f volcanogenic massive sulphide deposits have been described by numerous authors over the past fifteen years and it is now widely accepted that these deposits comprise a major ""deposit-type."" In addition to these geological parameters, however, it is now becoming apparent that volcanogenic massive sulphide deposits show several distinctive grade-tonnage relationships. For example, Singer et al. (1975) demonstrated a slight negative correlation between copper grade and ore tonnage in their sampling of 146 volcanogenic deposits. In a study of 110 Canadian Precambrian deposits of this type, Boldy (1977) showed that the size of the modal deposit is 0.39 million tons, that of the median deposit is 1.40 million tons and the arithmetic average is 6.85 million tons. Moreover, Boldy's data show that the average grade of combined base metals (Cu + Zn + Pb) for each of the se three deposit-sizes is, respectively, 6.25%, 5.35% and 6.47%. Because the lead content of Canadian Precambrian volcanogeni c deposits is most frequently less than 1%, the total metal grade is effectively Cu + Zn . From Figure 2 in Bold y (1977), it can be seen that 83% of the deposits fall in the range of 0.l to 10 million tons ."

Jan 1, 1980

By S. Amira

The corrosion behavior of high pressure die-cast and thixocast AXJ530 magnesium alloys has been investigated in 0.05M NaC1 solution at pH 6.0 using potentiodynamic polarization tests, electrochemical noise (EN) technique, electro-chemical impedance spectroscopy (EIS) and scanning reference electrode technique (SRET). The behavior of die-cast and thixocast specimens were compared using each of these techniques and the results discussed. Further tests have been carried out with die-cast AZ91D alloy to better compare and interpret the results. Experiments indicate that the thixocast specimens of AXJ530 alloy have a better corrosion resistance than those of die cast alloy in neutral solution.

Jan 1, 2006

By Phillip Mackey, Elmira Moosavi-Khoonsari

L'industrie du cuivre traverse une période passionnante, marquée par une forte demande, de bons prix et l'ouverture de nouvelles grandes installations. L'année 2022 a battu des records de production de cuivre, ce qui laisse entrevoir un potentiel de croissance supplémentaire. De grands projets sont en cours, comme la technologie Double Flash à Manyar, en Indonésie, qui peut produire plus de 500 000 tonnes de cuivre par an. À Munda, en Inde, on a construit la plus grande usine de cuivre du monde, qui produit plus de 1 000 000 tonnes de cuivre par an en combinant deux phases. De plus, l’installation de cellules de flottation de dernière génération au Mexique, au Chili et dans d'autres pays témoignent de la volonté de l'entreprise d'utiliser les technologies les plus récentes [1]. L'importance du cuivre dans la transition énergétique est évidente, l'accent étant mis à la fois sur la croissance et sur la protection de l'environnement. Cela se traduit par le développement d'usines de premier ordre dédiées aux pratiques durables.

May 2, 2024

By E. Trickey

In the mining industry there exists a constant drive for increased safety and productivity and decreased operating costs. This acts as a driver for implementing advanced technology. As more and more mining operations turn to new technologies, an observed bottle-neck for technology advancement has been the limitation of machine vision solutions available. LiDAR has been seen as a possible solution to the machine vision problem. In the past, a few studies on machine vision solutions have been undertaken by various groups involving scanning laser range-finders and millimetre-wave radar. These studies have done little more than highlight the limitations of both technologies in the mining environment. Little work has been done, however, exploring the applicability of LiDAR imaging technology for mining applications. Neptec Technologies Corp. has developed an obscurant-penetrating LiDAR (OPAL) sensor technology which overcomes the limitations faced by traditional LiDAR sensors when operating in a dusty environment, as well as advanced 3D real-time intelligence (3DRi) data processing algorithms that enable the real-time exploitation of 3D imaging data with sensors mounted on moving vehicles. Working with Teck Resources Ltd. and Barrick Gold Corporation, Neptec is adapting the OPAL sensors and 3DRi technology to mining applications. This paper highlights a number of real-time OPAL/3DRi based mining applications demonstrating how this technology overcomes the limitations of traditional LiDAR to provide a real-time machine vision solution that supports mine machine autonomy.

Aug 1, 2013