Search Documents

By Alfred E. Pugsley

PAYMASTER CONSOLIDATED MINES, LIMITED, began an investigation into the economy and use of detachable bit drill-steel in June, 1937. This investigation has continued to the present time, and was made necessary by transportation and distribution difficulties that had arisen through the use of standard steel in three widely separated mine areas serviced by a central steel-sharpening shop. Detachable bit drill-steel performance was first studied in the workings of No. 2 mine, where the rock being drilled was composed mainly of porphyry or tourmaline, and where standard drill-steel transportation costs had been excessive. The results obtained in this early work definitely established the economy of detachable bit drill-steel at No. 2 mine. This conclusion was reached when the 're-grind' system of re-sharpening dulled detachable bits was 1n use. Preliminary observations on the performance of detachable bit drill-steel in the quartz-carbonate veins of No. S and No. 6 mines gave encouraging results, and warranted a large-scale investigation under practical mining conditions. All drilling operations were gradually changed over to use of detachable bit drill-steel. This change was completed by February, 1938.

Jan 1, 1939

By A. G. Scobie

THE research laboratory of this Company was recently faced with the problem of determining trace amounts of tungsten in a series of classifier sands. A spectrographie survey revealed the feasibility of using this instrument in the final evaluation, but a check of the common methods in use for the isolation of tungsten (3, 4) showed these methods to give incomplete separation for trace amounts. An investigation into the possibility of modifying these procedures, or developing others, was thus indicated. ASSAY PROCEDURE Weigh 10 grams of 200-mesh ore or concentrate into a 400-ml. beaker, wet the sample well with about 20 ml. of water, and add 100 ml. of hydrochloric acid. Cover, digest at 60° to 70° C. for about 1 hour, and then boil down to approximately 25 ml. Cool, add 25 ml. of hydrochloric acid and 10 ml. of nitric acid, and again boil to former volume. Add 20-ml. portions of nitric acid with successive boiling clown until chemical action is complete. Then add 20-ml. portions of hydrochloric acid until all nitric acid is removed. Take nearly to dryness on a law-temperature hot plate, but do not bake. Take up in 10 ml. of hydrochloric acid and 20 ml. of water and heat on a law-temperature hot plate until all iron goes into solution. Dilute to 200 ml. and heat to just below boiling. Stir in pulp of about half of a No. 41 Whatman filter paper (12.5-cm.) and continue digestion on plate with occasional stirring for 15 to 20 minutes.

Jan 1, 1943

By G. P. Kundargi

India is one of the fastest growing economies in the world. The role of the Iron & Steel industry is very important for the development of the country. Iron and steel are among the most important components required for the infrastructure development of the country. This is one of the fastest growing sectors. The demand drivers for the Indian Iron & Steel industry are increase in the activities of the manufacturing industry and infrastructure development. Indian Iron & Steel industry with its strong forward and backward linkages contributes significantly to overall growth and development of the economy. The industry today directly contributes 2% of India?s Gross Domestic Product and its weightage in the official Index of Industrial Production (IIP) is 6.2%. Manganese is a main ingredient for production of steel. Almost 90% manganese is being utilized by the steel industry worldwide. Globally, there is no substitute for manganese as on date. There is huge gap between demand and production of manganese ore in the country. To meet this demand gap and to support for growth of national economy, MOIL Limited (formerly Manganese Ore India Limited), a Government Enterprises, producing annually around 1.1 million tonnes (mt) of manganese ore and value added products, has geared up with various infrastructural activities to increase the present production capacity of 1.1?1.5 mt in 2016?2017 and 2.2 mt in 2020?2021. The paper deals with the technological improvements and infrastructural development activities of MOIL; this will help MOIL to become the market leader in manganese ore production globally in the coming years.

Aug 1, 2013

By G. W. Govier

The origin and limitations of the conventional and empirical equation for the interpretation of the results of back pressure tests on gas wells are discussed. Difficulties in data interpretation arise from many causes, including Jack of flow stabilization, uncertainties in connection with the friction calculation, and the effect of turbulence near the sand face in the reservoir. A procedure is developed to ac-count for the turbulence effect. This is based upon the theoretical equation for laminar steady state flow and current knowledge of turbulent steady state flow. The procedure involves the expression of the equation for combined laminar-turbulent steady state flow in terms of a turbulence contribution factor. This factor. is shown to be dependent mainly upon the flow rate per unit of pay thickness and the reservoir permeability. The method of interpretation permits the use of judgment based upon the theory and present day under-standing of laminar-turbulent flow and is considered an improved method

Jan 1, 1961

By F. R. Ploeger, J. H. Crocket

"IntroductionRocks in the Kirkland Lake district form part of the Timiskaming Group, a south-facing homoclinal sequence of wackes, conglomerate, trachytic flows and pyroclastic rocks and syenitic intrusive rocks. Hewitt (1963) indicates that the thickest section, about 5 km, of the Timiskaming Group rocks is attained in Lebel Township. Several writers (Thomson, 1948; Hewitt, 1963; Hyde, 1978; Jensen, 1978; and Downes, 1979) have observed that the Timiskaming Group unconformably overlies the Keewatin volcanics, particularly along the northern contact. Recent work by Downes (1979) in McGarry and McVittie townships to the east of Kirkland Lake has shown that much of what had formerly been classified as Timiskaming actually belongs to an older group of rocks, the Larder Lake Group (Jensen 1978).General GeologyA series of fluviatile, braided-stream sedimentary rocks (Hyde, 1978) form the oldest of the three major rock suites at Kirkland Lake. Conglomerates constitute a large proportion of these sedimentary rocks and typically contain a large percentage of a variety of locally derived alkalic rock clasts as well as the distinctive red jasper iron-formation pebbles (Fig. 1a). The associated wacke units can be massive to finely bedded and are interbedded with the conglomerate. They also contain a large alkalic tuffaceous component.Interbedded with these sedimentary rocks are alkalic extrusive rocks, including tuffs, agglomerates, breccias and flows, which represent episodes of fissure and explosive crater eruption (Cooke and Moorhouse, 1969). The tuffs, although dominantly alkalic in composition, are commonly reworked and contain sedimentary features such as graded bedding, scouring and crossbedding (Fig. 1 b). The trachytic flows are massive to porphyritic and outcrop mainly east of Kirkland Lake in the adjoining townships. Altered leucitic porphyritic flows, locally referred to as red and green spotted trachytes, commonly occur."

Jan 1, 1982

By C. R. Fast, G. C. Howard

The loss of fluid to the formation adjacent a fracture governs the areal extent of the fracture and the success of hydraulic fracturing as a production stimulation technique. The three flow mechanisms which control this loss are the result of the viscosity of the fracturing fluid and the permeability of the formation to the fracturing fluid, its wall building properties, and the combined effects of viscosity and compressibility of the reservoir fluid. The effects of these flow mechanisms can be evaluated in terms of a fracturing fluid coefficient, the fundamental concepts of which are developed in the paper. The fracturing fluid coefficient, which may be used in calculating the areal extent of fracturing, affords a direct measure of the effectiveness of fracturing fluids. The area of hydraulically created fractures is in-creased as the coefficient is de-creased. The fifteen-fold variation noted in this coefficient for the commercially available fracturing fluids tested resulted in a six-fold difference m the calculated areal extent of the fracture system.

Jan 1, 1961

By Therese Schneck

The presence of xenon isotopes from in-situ spontaneous fission of short-lived Pu244 has been confirmed in Hadean detrital zircons from Western Australia. Hadean and meteoritic zircons can retain secondary overgrowths developed after primary cristalization at 3.97-3.94 Gyr. On the moon, the metal grain in sample 66095,78 is mantled by troilite, schreibersite and cohenite. High chlorine content FeCl2 is deposited around metallic FeNi. The magnitude of Pollonium-210 to Radon-222 on the Aristarchus plateau spectrum indicates a past greater activity. The Earth Moon system from Nb/Ta systematics is consistent with a Moon iron core delayed to 3,9 Gyr.

Aug 1, 2010

By R. C. Hartviksen, B. H. Boyum

"The Sherman Mine, Temagami, Ontario, is an iron ore pellet operation rated at one million tons per year capacity. Mining is done from three open pits in two bands of Keewatin iron-formation intercalated in a 'greenstone belt' thought to be part of the Archean 'Abitibi Belt'. The bands of iron-formation are tabular and steeply dipping, averaging 75 degrees. The principal ore mineral is magnetite.Blast holes, 1214 inches in diameter, are drilled on 28-foot centers, each hole being sampled and assayed for both total iron and magnetic iron. Concentration tests are made in the laboratory to determine the anticipated concentrate grade. Two classes of ore are recognized -'liberating' or 'refractory'. Blending is done on iron con-.tent, degree of ease of liberation (i.e. grain size) and chunkiness. The latter is important, as primary milling is done in autogenous mills. Actual daily mill results are compared with predicted grade from blast holes, exploration diamond drill holes and pit inspection. Hourly mill samples are analyzed by the X-Ray Fluorescent Analyzer, with emphasis on silica grade. In 1969, the pellet grade was improved from 7 .01 per cent silica natural to 5.50 per cent silica natural."

Jan 1, 1970

By S. Kashani-Nejad

The formation of oxides during the dehydration of MgC12,6H20, Bischofite, was studied by heating the bischofite over a range of time and temperatures in ambient atmosphere. Using a methanol-leaching technique developed by authors, the oxides that formed were isolated, identified and assayed. Three distinct regions of oxide stability were identified. The oxide produced at dehydration temperatures less than 300 °C was Mg2(OH)3C1,2H2O; at 300 °C, mixtures of MgOHC1 and Mg2(OH)3C1.2H2O were formed and at 400 °C, MgOHC1 was the only oxide produced. The presence of MgO observed in the products of the dehydration of bischofite at temperatures above 400 °C was due to the thermal decomposition of the MgOHC1 that was formed while the sample was heating to over 400 °C.

Jan 1, 2006

"Ore deposits containing rare earth elements normally contain small amounts of the radioactive elements thorium (Th) and/or uranium (U). These are the naturally-occurring isotopes U238, U235, and Th232 (and associated decay-series daughter products) that are ubiquitous in nature, and that contribute a small percentage of the natural background radiation exposure encountered by humans. The presence of these radioactive materials in the ore deposit creates potential hazards to human health and the environment that must be dealt with properly in the mining, processing, and refining of the ores, as well as management of waste streams and residues. This paper presents an overview of the environmental and safety issues associated with U and Th, with particular emphasis on rare earth mining, processing, and refining projects; the regulatory approaches followed to ensure that rare earth deposits are developed, operated, closed, and decommissioned safely; and the development of information during the project predevelopment work and permitting processes that feed into the design, operation, and closure of tailings impoundments and milling/separation/refining facilities. Case studies will be presented subject to the availability of relevant public information. INTRODUCTIONNearly all ore deposits containing economically-recoverable rare earth minerals also contain small amounts of the radioactive isotopes for the elements thorium (Th) and/or uranium (U) and their associated radioactive decay products. Therefore, the handling and management of these materials in mining and mineral processing operations must be performed so that workers and the environment are protected from harm from Th and/or U (and their radioactive decay products), just as they must be protected from any other potentially harmful constituents present in the ore or introduced in processing. Examples of these might include ores with high sulfide content, which may pose a risk of acid rock drainage, or chemicals used in ore processing and metals production.The purpose of this paper is to present information on how rare earth mining and processing projects with ores containing Th and/or U can be developed, operated, and decommissioned safely according to applicable regulations intended to protect worker health & safety and the environment.It should be noted that some countries are considering developing Th as a feedstock for producing nuclear energy, which could have some effect on future development of rare earth ore deposits. To avoid confusion, that issue is not discussed in this paper."

Jan 1, 2012

By O. A. Ojo, N. Esmaeili

"The effects of brazing and use of composite powder mixture as interlayer material on hot corrosion resistance of brazed IN738 superalloy were studied. Brazing was observed to result in significant reduction in the hot corrosion resistance of the superalloy. However, application of composite powder mixture, which consists of additive superalloy powder, enhanced the hot corrosion resistance of brazed samples. It is also found that although the use of composite powder mixture increased hot corrosion resistance of brazed alloy, if the additive powder completely melts, which is possible during brazing, it can significantly reduce the hot corrosion resistance of the brazed joint. Elemental micro-segregation during solidification of the joint with completely melted powder mixture produces chromium depleted zones and consequently reduces hot corrosion resistance, since a uniform distribution and adequate chromium concentration is necessary to combat hot corrosion. This has not been previously reported in the literature and it is crucial to the use of composite powder mixture for enhancing the properties of brazed superalloys.INTRODUCTION Superalloys have been developed in response to the increasing demand for materials with higher resistance to corrosion and creep and also with higher mechanical strength at higher temperatures (Smith, 1981). Ni-base superalloys are predominantly used in manufacturing hot sections of gas turbine engine components. This is due to their high strength and corrosion resistance in extremely high temperature service environments which is typical for hot sections of gas turbine engines (Miglietti, 2009). The continuous demand for higher efficiency and output has resulted in the use of higher operating temperatures and gas pressure in modern gas turbine engines (Jahnke & Demny, 1983). Consequently, this has caused thermal and mechanical stresses which result in severe degradation and damage of gas turbine engine components due to creep, fatigue and hot corrosion (Zhang, Feng, & He, 2006). The decision to replace or repair damaged parts depends on the overall repair cost and expected life of the repaired components (Jahnke & Demny, 1983). However, in most cases, it is more cost effective to repair damaged parts rather than use a full replacement."

Jan 1, 2017

By Dougal R. McCreath, Dwayne D. Tannant, Peter K. Kaiser

The Geomechanics Research Centre at Laurentian University in Sudbury, Canada, has undertaken a five-year research program into the design of support appropriate for control-ling damage caused by rockbursts. Rockburst damage mechanisms in Canadian hardrock mines are reviewed and a support design approach is presented. Each element in a sup-port system performs a reinforcing, holding, or retaining function. The desirable load-displacement characteristics for elements in burst-resistant support systems are described, and recommended support systems are presented for a spectrum of rockburst conditions ranging from minor to severe. A support system can be designed to (a) prevent the triggering of aground fall or a rockburst; (b) deform to accommodate the large imposed deformations arising from a rockburst; or (c) absorb the kinetic energy contained in ejected blocks of rock.

Jan 1, 1996

By A. P. LeBis

This article attempts to relate the concept of utility to the risk involved when only a small number of projects (compared to their probability of occurrence) are accessible to a firm and to quantify utility when other financial and physical parameters are known.

Jan 1, 1978

By Kevin J. Melong

"Redpath Canada Limited and joint venture partner Thyssen Mining and Construction Canada have recently completed the sinking of the Scissors Creek service in Saskatchewan through its joint owned company, Associated Mining Construction (AMC). The Scissors Creek service shaft was sunk at Nutrien’s Rocanville mine. The following paper outlines the shaft sinking plant and the methodology related to sinking and shaft lining. KEYWORDS Hydraulic shaft jumbo, Hydraulic shaft mucker, Potash shaft sinking, Shaft lining, Sinking galloway INTRODUCTION The sinking and lining of shafts at mines to access mineral deposits has always been one of the great mining challenges for owners, engineers and contractors. Over the course of history in Canadian mining, the sinking of potash shafts through the notorious Blairmore formation of Saskatchewan has proved to be some of the most challenging shaft sinking projects on record. There is no doubt that today’s shaft sinking business demands the utmost in safety performance while delivering projects within schedule and budget. Given these requisites, Redpath and TMCC (executed under the joint venture company, Associated Mining Construction or AMC), were taxed with developing the shaft sinking system to deliver this program in the safest and cost effective manner, with due regard to schedule and quality. Traditionally the potash shafts sunk in Saskatchewan involved a significant level of manual labour, owing to the methodology of excavation by means of chipping the frozen shaft sections with hand held pneumatic machines, and manually placing tubbing segments or steel liners of the shaft lining system. Most certainly, the AMC team wanted to make a step change from those earlier sinking programs and develop systems for sinking this potash shaft that removed the high level of manual work, thus making this project inherently safer, while endeavoring to sink more efficiently. With that in mind, the team embarked on a design program to improve its overall shaft sinking systems without the requirement for excessive capital and methodology flexibility to adapt to potential changing conditions expected to be encountered during shaft sinking. This was especially important should the new approach be met with less than expected success, and retrofitting of the system was required. The concepts were developed to provide for a much improved work environment, while easing the manual labour burden on the workers with innovative equipment and approach to the work."

Jan 1, 2019

By F. E. Patton

"IntroductionAT NORANDA, the strength of the ore and wall-rocks per-mitted mining in large open stopes. While some of the orebodies were small and could be mined out in one stope, in most cases their size was such that it was essential that ore pillars be left during the first stage of mining. In these cases, backfilling has been necessary for ground control and to facilitate the later recovery of the ore in these pillars.This paper discusses the development of the •backfill and •its use in pillar recovery.GeologyThe ore bodies at Noranda occur as replacement deposits in a block of rhyolite flows and breccias, bounded on the north by the Horne Creek fault and on the south by the Noranda Andesite fault. Mineralization consists of pyrite, pyrrhotite, magnetite, chalcopyrite, sphalerite, gold, and various tellurides.The main orebody is a massive sulphide deposit designated the 'H' orebody. It is elliptical in plan, measuring roughly 400 feet by 800 feet, and is divided into two zones -Upper H, extending from surface to the 1,500-foot level, and Lower H, from the 1 ,500-foot level to just below the 3,000-foot level.Mining MethodsOpen stope mining in both Upper H and Lower H zones has been fully described in previous publications (1). A brief review only of the mining methods will be given here."

Jan 1, 1952

By Joseph F. Daniels

In recent considerations of the utilization and beneficiation of coal, the chemise and the chemical engineer have been occupying the centre of the stage with their presentation of the picture of new fuel forms. The stage hands and supernumeraries of the cast, the miners and the consumers who carry the brunt of the present-day burdens, are apt to be forgotten in the glorious settings and the climaxes. With no thought of disparaging or of minimizing the efforts of our fellow scientists, let us remember that economic considerations as well as technical difficulties will limit these chemical applications, which must develop and move slowly before reaching the stage of industrial application at some later day. In the meantime, the coal-mining industry must live on hard faces rather than rosy dreams. In these brief notes it is my purpose to call attention to some of the physical advances in the utilization and beneficiation of coal which have been of interest to the industry in the State of Washington.

Jan 1, 1928

By RALPH R. STEA, John H. Fowler

Clay, quartz sand and lignite deposits overlie Carboniferous rocks in central mainland Nova Scotia. Recent evidence indicates that these deposits are fairly extensive. Sands consist of almost pure angular quartz grains. Clays are highly plastic and range in colour from black through grey and blue to mottled red and white. Palynologica/ information dates the sediments as Ear{y Cretaceous, and mineralogical studies show them to consist primarily of quartz, kaolinite and mica. There is not yet enough evidence for detailed stratigraphic description, but sequence and thickness of sediments are known to vary greatly over short distances. Drill logs from Musquodoboit Valley recorded Cretaceous sediments at 168 m thick. Of the three active pits in Cretaceous sediments of central Nova Scotia, two are for silica sand production and are located at Elmsvale and Brazil Lake while a third pit at Shubenacadie produces clay for manufacture of structural clay products.

Jan 1, 1984

By F. Khomamizadeh

In this study, deep cryogenic treatment was applied to A319 cast aluminum samples. Although the cryogenic treatment didn't have any significant effect on mechanical properties of the well degassed and fluxed samples, but the tensile strength of the samples containing a considerable amount of gas and shrinkage defects was improved surprisingly, This improvement was attributed to the strengthening of the a-aluminum matrix which slows down the propagation of the existing defects. There was no significant increase in the hardness after cryogenic treatment, The abrasion resistance of the alloy was improved after cryogenic treatment, by developing a homogeneous protector shield, composed of abrasive grains penetrated into the soft aluminum matrix and kept tight.

Jan 1, 2005

By G. R. Larocque

"The Loss Prevention Program and management style applied at Kidd Creek enabled them to maintain a 1.02/200 000 man-hours accident frequency over a 20-year period. Falconbridge Limited, Kidd Creek Division operates a major zinc, copper, silver mine, two gold mines and a metallurgical facility in Timmins, Ontario. The metallurgical site and the base metal mine are 17 miles apart and joined by their own railroad. The minesite consists of two shafts, one 3000 feet deep and the other to 5200 feet deep, as well as the necessary maintenance and service shops. The metallurgical site consists of a 14 000 STPD concentrator, a zinc refining plant, copper smelter, copper refinery, and the necessary maintenance shops. The two gold mining operations are adjacent to the metallurgical site.At the time of writing this paper the workforce consisted of some 2500 people divided between the two sites. Nine hundred and ninety-two employees are stationed at the minesite, with the remainder at the metallurgical site and gold mines. The workforce in the Timmins operation is non-unionized and reflects the belief that employee interests are well served.Beside providing competitive wages and an excellent benefit package, Kidd Creek takes special pride in its employee relations practices and continued efforts in communication.In each of the programs referred to, there have been equal involvement by both management and the employees. Each crew, under the direction of a supervisor, makes up its own health and safety committee. To maintain a successful Loss Prevention Program, it is essential that management and the employees work closely together and provide meaningful input and effort to succeed.At this point, refer to the lost time injury frequency as a measure of failure and refer to the opposite end of the scale as the measure of success. The ultimate goal of every operating company is to have a zero frequency, therefore denoting 100070 success. The company uses most of the tangible safety aids found in other mining operations, such as safety posters, safety reminders, check lists, and the use of the Neil George Safety System. The difference is the manner and style of management at the Kidd Creek Division. Their ""open door"" policy and the close association, between management and the employees, has always served them well. Also, at Kidd Creek they believe they have a well-trained and dedicated workforce."

Jan 1, 1989

By H. Henao, F. Canales

The present work evaluated the use of copper ore flotation tails as flux in the process of smelting copper concentrates. For this purpose, experimental and simulated liquidus lines were obtained at different ratios of tail/flux. Experimental variables included temperature, partial pressure of oxygen and sulfur dioxide and the conditions of tridymite or spinel saturation. The results indicate the feasibility of replacing the flux by increasing the temperature of the smelting process by 20°C. Results of simulation using FactSage and HSC confirm that the required increase in temperature can be achieved by increasing the flow of concentrate, enrichment of oxygen or increasing the matte grade. INTRODUCTION In the pyro-metallurgical process of copper production, the smelting stage produces two liquid phases, a sulphide phase rich in copper and another composed mainly of oxides called slag. The slag phase is the product of oxidation of the iron contained in the flotation concentrate. The smelting process which is carried out at temperatures of 1250°C, require the addition of silica as a flux and the injection of air enriched in oxygen (Schlesinger 2011). Currently, one of the most important aspects of the mining industry is the minimization of costs, the optimization of the use of available resources and the reduction of environmental impact. Under this context, the use of flotation tails from as a flux in the copper smelting process has the potential of reduced production costs and generate an environmental benefit by reduce the disposal amount of this waste material Regarding the use of copper tails as flux in the copper smelting process, a thermodynamic simulation study using the FactSage software had been reported in the literature (Parra et al., 2011). The results indicated an increase of 35°C in the temperature the liquidus for the equilibrium matte/spinel and a subsequent requirement of energy in the process of approximately 350 [MJ/ton slag]. Given that the calculated viscosity remains in the same order of magnitude, the melting temperature is a more relevant parameter for the evaluation of the use of tailings as flux.

Jan 1, 2019