Search Documents

By R. Tremblay, M. Burrows

"In the summer of 1990, pilot scale testing of a Jameson cell was carried out at Falcon bridge Limited, Kidd Creek Division. The Jameson cell is self aspirating and has fewer mechanical parts, thus it has a lower operating cost compared to conventional cells. This lower operating cost combined with positive pilot scale results, justified the evaluation of two full scale cells in the plant. The plant test had two mandates:1. Gain a thorough understanding of the cells operation and design constraints.2. Develop a flow sheet to replace three divisions of copper cleaner flotation.This paper provides an overview on the installation, commissioning and evaluation of the two Jameson cells acquired. The current status of the test program is also discussed.IntroductionThe Falcon bridge Limited-Kidd Creek Division concentrator is located in Timmins, Ontario. The concentrator, commissioned in 1966 and expanded in 1978, consists of four parallel grinding and flotation divisions utilising small cell (60 ft3) technology. With increasing pressure to maintain low operating unit costs a series of studies were undertaken to assess the impact of new technologies in the flotation circuits. The goals of the project were to improve productivity through increased metallurgical performance and/or reduced operating costs.One of the technologies investigated was the Jameson cell designed by Dr. Graeme Jameson of the University of Newcastle and marketed by MIM Holdings Limited, Australia. This style of column technology was chosen based on its potential for reduced capital and operating cost versus large conventional cells.The success of pilot testwork in 1990 led to the installation of two production sized Jameson cells beginning in October 1991. The units were to be used to confirm pilot results and determine equipment requirements for flotation modernisation. This paper will discuss the results and experiences Kidd Creek has had with the Jameson cell from pilot scale through installation and commissioning of the plant units."

Jan 1, 1993

By C. Peña, C. A. Zaror, M. Bustamante, M. Vega

The goal of this paper is to present the carbon footprint of Chilean cathodic copper, as a function of the electricity generation mix, ore grade, and process efficiency. Ore grades and acid leach-solvent extraction-electrowinning (LX-SX-EW) yields in the range 0.5-1.0% and 60-80%, respectively, were considered here. Additionally, electricity supply from two Chilean suppliers, SING (1.0 ton CO2/MWh) and SIC (0.4 ton CO2/MWh) was assessed. Simulation results show that oxide plants located in northern Chile, served by the SING network, feature carbon footprint within 4.3 - 11.4 MWh I ton cathodic copper, as compared with 3.5 - 9.3 MWh I ton copper in plants served by SIC. The footprint was found to increase as ore wade and process yields decrease.

Jan 1, 2011

By Douglas Brand

"The data that many mineral processing plants make use of, is provided by samples taken from sampling systems which are inadequately designed or improperly maintained, and therefore cause detrimental effects to plant operations, production planning and metallurgical accounting! Poorly designed or maintained sampling systems will likely produce low probability samples which give the operator a false sense of security of the product and the process. If data is the basis for action (Flintoff, 1992, p.2), then using the resulting suspect or bad assays by operators, control systems, or metallurgist and administration personnel will act and make decisions which may adversely affect the profitability of a processing plant. Here we will discuss some of the fundamental sampling problems, propagation of errors and a method to estimate what impact this has on an operations Net Smelter Return.INTRODUCTIONIn order to control a mineral processing plant at its best potential, it is necessary to obtain the best possible measurement results of the metal or mineral in question. The sample which is delivered to a measuring instrument, or lab, needs to be of the highest probability to be able to achieve this. This paper will discuss the effects of sampling errors on grade / recovery and grade / Net Smelter Return (NSR) and provide a method to estimate the monetary advantages of using probabilistic sampling in a processing plant.REVIEW OF SAMPLINGSampling, by definition, is the removal of a small representative portion from a total consignment, or flow, for the purpose of accounting or process control.• A sample can only be considered representative, if each and every increment collected, in each of the sampling stages, is representative.• Each particle of the sampling lot must have the same probability of being included in the final sample.• If both of the above conditions are met, then the final sample will be representative of the complete sampling lot.It is commonly known that in order to take truly representative and probabilistic sample, best practices indicate that:• The total stream should be sampled.• The sample cutter should intersect the sample at right angles to the flow.• The sample cutter should travel through the stream at a linear and constant speed and the speed deviations should be less than 5%."

Jan 1, 2016

By D. Chakravarty, B. Samanta, D. Ghosh

Autonomous robots are useful for 3D underground mine mapping to avoid human exposure to hazardous spaces. To prepare a precise mine map, a self-navigating robot must navigate an arduous path, avoiding obstacles and sensing the environment. A prototype laboratory-scale robot was built and evaluated through a mock-up in a test mine gallery. It was outfitted with a 2D laser scanner, a stereo camera for obstacle avoidance, and a high-precision, laser-based imaging and digitizing system for collecting 3D point cloud data. Various algorithms were used for scan matching to facilitate simultaneous localization of the robot for mapping.

Jan 1, 2014

By T. W. Sullivan

"This paper explores the history of AC static variable frequency control drive systems on open cast mining machinery, in particular electric mining shovels and electric walking draglines, over the past ten years. It critiques the peformance of these drive systems from a productivity and operating cost standpoint and evaluates the over-all success of the original design concepts as they were envisaged in the 1970s. The paper details the state-of-the-art as it exists today as well as design improvements contemplated for the immediate future.IntroductionConsidering the fact that the very first successful application of an alternating current electrical distribution system occurred at the Gold King gold mine near Ames, Colorado, U.S.A., in the year 1891, it seems somewhat ironic that almost 100 years later, AC excavator drive systems are just now becoming commonplace in the mining industry.If one were to read the biography of Lucien L. Nunn, the first person to successfully install a commercially viable alternating current power distribution system, one would quickly visualize a parallelism between his fight to achieve acceptance of his new lower cost technology and that of those commissioned with the belief that AC static variable frequency control drive systems are not only a better performing, lower cost drive system for mining excavators today, but moreover, the drive systems of the future in our industry.This paper will deal with the evolution and incorporation of AC static drive systems on open cast mining excavators. It will trace the history of the development of these drive systems in the mining industry, the current state-of-the-art concerning these systems, and what the future holds for these excavators in our industry."

Jan 1, 1990

By S. R. McCutcheon

"The regional stratigraphy of the Lower Carboniferous Windsor Group in the Moncton Subbasin indicates that evaporites could be present in the Marysville Subbasin, part of what was formerly called the Central New Brunswick Platform. The Windsor Group consists of basement-fringing, algal build-ups (Gays River Formation), in places with intercalated siliciclastics (Parleeville), which are laterally equivalent to deeper-water, very thin to thinly bedded, euxinic limestone (Macumber). The Macumber is overlain by stratiform, nodular to mosaic anhydrite (Upperton) that is hosted by carbonate or calcareous siliciclastics. The sulphate also is equivalent, in part, to the algal buildups. Deep-water salts (Cassidy Lake) which overlie and in places are laterally equivalent to Upperton rocks have a basincentre distribution. The Windsor Group is overlain by shallow water evaporites and mudstones (Clover Hill) or by greenish grey mudstone (""transitional beds""). The paleogeographic distribution of these rocks provide important clues that help predict where deposits of salt and potash can occur.IntroductionCurrently there are three known potash deposits in southern New Brunswick (2, 3 and 4, in Fig. I). All three deposits occur in the Windsor Group of the Moncton Subbasin, but until recently their exact stratigraphic position within the group was not known.The Windsor Group is a cyclic sequence of carbonates, evaporites and red beds that is up to 1.0 km in thickness (Schenk 1969, p. 1038). It is Late Mississippian (Visean) in age and the type area is near Windsor, Nova Scotia. The group was named by Dawson (1873) but the rocks were described earlier by Hartt (1867). Dawson (ibid.) was the first to assign rocks in southern New Brunswick to the Windsor Group."

Jan 1, 1983

By J. S. DeLury

Introduction The problems of metallogenesis are largely related to those concerning the origin of igneous rocks, which, in turn, are involved with the question of crustal mechanics. Many ore-bodies are genetically related to associated intrusive and there is an equally close association apparent between igneous intrusion and crustal deformation. The problem of ore-deposition is concerned, therefore, with the fundamental problems of geology. For a long time speculations regarding crustal movements rested largely on the contraction theory and its associated conceptions. Vertical movements were considered to be all important and horizontal movements secondary to them. Magmas were pictured as rising more or less vertically in the crust and were believed to form in vertically disposed magma-chambers or reservoirs. The principle of magmatic differentiation seemed to offer the best explanation of the origin and association of diverse rock types and it seemed also to require the existence of quiescent magma-chambers for the admittedly slow process of differentiation. Accumulating evidence of the importance of horizontal movement in the crust, has, along with other considerations, discredited the contraction hypothesis and many of the inferences that go with it. The same evidence may require some change in the prevailing conception of the origin of the various types of igneous rock and of the mechanics of intrusion. Geologists are now at sea concerning some of the vital and fundamental problems of the crust, and the field is open for speculation. The writer is developing a hypothesis which seems to permit an explanation and? a correlation of earth structures and phenomena. If it rests on a firm foundation, the hypothesis, because it is fundamental, is certain to have a profound bearing on the problems of economic geology. It is for this reason that an outline of the hypothesis is offered at this time. Only a few of its economic bearings are foreseen at this time and these will be indicated.

Jan 1, 1932

By Alexander Smith

"The Silver Standard mine is 6 miles by road northwest of New Hazelton, B.C., a small town on the northern line of the Canadian National Railways some l 75 miles northeast of Prince Rupert. The deposits lie on the western slope of Glen Mountain (elevation 2,100 feet), with the main adit, mill, and campsite at 1,300 feet. The deposits were found in 1910, shortly after the area had been swept by forest fire and during a period of prospecting activity spurred by the construction of the railway. Crude ore only was shipped until 1918, when a 50-ton gravity mill was built which operated until 1922. Gross value of production of this period, at present metal prices, was about $1,000,000.In 1947 the present company was formed and a 50-ton flotation mill installed. Production from 1948 to 1955 has been in excess of $10,000,000, and net smelter returns about two-thirds of this amount. More than 60 per cent of the production and 80 per cent of the profit have come from one vein, No. 6. On the 1,300-foot level this vein had an ore section 375 feet long and 2.5 feet wide, averaging 0.18 ounces gold, 85 ounces silver, 10 per cent lead, and 16 per cent zinc.The mine workings follow a simple pattern. A series of parallel veins, striking northeast and dipping southeast, are numbered from 0 to 12, starting at the northwest. They lie within a zone trending south 70 degrees east, and the distance between Nos. 0 and 12 veins is about one mile. Recently several cross-veins, dipping northeast, have been found between Nos. 8 and 12. They are apparently of the same type as the others, though they may not have the same structural controls. They could be an important new source of ore.The mine has been developed principally by crosscut adits at the 1,500- and 1,300-foot levels and a 510-foot shaft with levels at I, 150, 1,000, ·and 850 feet. Drifts and crosscuts total 17,000 feet, chiefly on Nos. I, 4, 6, 7, and 8 veins. The drifts are stoped by shrinkage, top shrinkage rill, cut-and-fill with resuing, or open stope methods. The mill produces a lead-silver-gold-copper concentrate and a zinc concentrate, with indicated recovery of more than 96 per cent (4)."

Jan 1, 1949

By M. B. Myers

The subject matter of this paper will be discussed under three main headings. 1.-Fire-Resistant Fluids: (a) the need for such materials, based on historical events; (b) a definition of fire -resistant fluids; (c) general description, characteristics, operational parameters, advantages and disadvantages of oil-in-water emulsions (HFB), water-polymer fluids (HFC) and anhydrous or synthetic fluids (HFD). 2.-A review of equipment associated with the use of fire-resistant hydraulic fluids; (a) performance testing of hydraulic equipment, i.e. gear pumps, vane pumps, axial and radial piston pumps, hydraulic motors, etc., pressure, speed, filtration limitations, etc., and effects on valves, elastomers, paints, etc.; (b) hydraulic system design features and selection of suitable units; (c) types of mining applications currently employing fire-resistant fluids. 3.-Test methods used to evaluate fire-resistant fluids: (a) fire testing methods, i.e. wick tests, spray ignition testing, hot manifold tests, factory mutual tests, all to establish fire-resistancy parameters and acceptance; (b) new developments in fire-resistancy evaluation; (c) the examination of other performance tests, e.g., effects of evaporation, sliding wear, life of rolling element bearings, etc.

Jan 1, 1979

By D. S. Harries, R. I. L. Guthrie

"The use and development of scientific disciplines involved in heat transfer technology, related in general to steel masses and in particular to batch annealing, is demonstrated.The measurable benefits of cooperation are tabled; on industry's side, this includes a 10 to 20 per cent decrease in annealing time, and a corresponding higher productivity potential. The returned benefits to the academic engineer include the development and refinement of new computer algorithms related to heat transfer mechanisms.IntroductionThe object of this discussion is not really to describe an improvement in the batch annealing operation, but to use the project as an example of joint work between industry and the academic field. Both parties have derived a number of substantial benefits. These benefits will be listed, of course, but the batch anneal project will be used just as a typical example of cooperation. Why it happened will be explained, what actually happened will be described and finally some thoughts about areas in the field of heat transfer, where cooperation will continue in the future, will be highlighted. The paper will close with a message.Industry OverviewAt the outset, perhaps it should be understood that, in general, the Research Department at Dofasco believes that the universities and their staff are not destined for the problem-solving role in industry. Its opinion is that the university staff is best suited to the gathering and dissemination of knowledge. There are other more professional problem solvers for industry, including the steel industries' own individual investigation groups. Dofasco, therefore, looks to its academics for consultation. It benefits by bouncing ideas off them, and through rubbing shoulders with them in such a way that their knowledge can be tapped, and thus establish more effective scientific routes. In addition, the younger and brighter engineer s can broaden their scope through the intellectual contact with experts. The university professors can, it is believed, benefit through closer contacts with result-orientated research. They can also develop an appreciation of the fiscal control necessary for industrial investigations, without government subsidies, grants, etc., and with massive overheads."

Jan 1, 1982

By D. M. Maijer, S. L. Cockcroft, A. B. Phillion, P. Fan, C. Reilly

"A numerical model has been developed to study macrosegregation associated with liquid feeding in the Low Pressure Die Casting of A356 aluminum alloy wheels. The model of the wheel casting process has been implemented within the commercial CFD software package, FLUENT, using a User Defined Function (subroutine) to account for Si rejection based on the Scheil approximation. The model has been validated against temperature and microstructural data taken from a commercially cast wheel. The amount of segregation in the wheel has been shown to be significant in a couple of key areas. The implications of accounting for segregation include an improved ability to predict shrinkage porosity, fatigue performance and potentially also hydrogen porosity.INTRODUCTION The aluminum alloy A356 is widely used in the automotive and aerospace industries for various components. Examples include automotive wheels, automotive suspension components and airframe castings. Focusing on automotive wheels, Low-Pressure Die Cast (LPDC) A356 wheels offer significant design freedom and are far more aesthetically appealing to consumers than conventional stamped steel wheels. A356 wheels now dominate the market, appearing in all but the entry level offerings of the OEM manufacturers. However, they are typically over-designed to allow for the various casting related defects that degrade their mechanical performance. Thus, their potential to save weight has not been fully realized. Wheel manufacturers are under constant pressure to ensure their products meet strict mechanical requirements (ductility, fatigue, vibration), tight geometric tolerances and high aesthetic quality. The mechanical properties of the final product are determined by the microstructure – e.g. SDAS – and the defect population (porosity and oxides). Depending on their size and location, both porosity and oxides, can act as crack initiation sites reducing fatigue life (Caton, 2001; Jordan, 2010; Wu, 2015). There are a number of examples appearing in the literature (Atwood, 2000; Carlson, 2007; Lee, 2001; Yao, 2011) of numerical models that have focused on hydrogen-based pore formation that have demonstrated an ability to predict porosity formation and pore size distributions in geometrically simple castings. These models assume that the local gas species diffusion through the liquid metal to the pores is the rate-controlling factor of pore growth. Another common source of porosity is liquid encapsulation (Dantzig, 2009). As the pressure within the isolated liquid drops, pores form first due to the pressure dropping below the equilibrium partial pressure of hydrogen in solution and then second grow substantially as the pressure continues to drop falling below the vapour pressure of Al. One factor that can affect both mechanisms of pore formation is species macrosegregation, which has received comparatively little attention in die-casting."

Jan 1, 2017

By D. J. Lloyd

"Bending is involved in the forming of many sheet parts and it is important to understand the phenomena involved. In this paper the basic equations describing bending on a global scale are compared with strain measurements of bent sheet. The development of strain on a local, microstructural scale is also investigated, as is the general aspects of plasticity and the failure process. It is shown that the global equations can be used to estimate the strains involved and the local strains can be attributed to various aspects of the plasticity. The bendability can be related to the fracture strain of the sheet and the ability of a sheet alloy to accommodate the necessary bending to form the part can be assessed.INTRODUCTION The ability of a sheet alloy to undergo bending without failure is an important capability in the forming of many parts and it is useful to be able to assess the bendability of an alloy during its development. The basic mechanics of bending were developed in the 1950s (Lubhan & Sachs, 1950; Hoffman & Sachs, 1953). When a sheet is bent the upper bend surface is in tension, the lower surface in compression and at some point within the sheet there is a plane of zero strain which is referred to as the neutral axis. For sheet exhibiting limited plasticity the neutral axis is static and occurs at the mid-point of the sheet thickness but for sheet exhibiting extensive plasticity the neutral axis progresses deeper in to the sheet as bending progresses. This results in two expressions for the maximum strain at the upper bend surface depending on the motion of the neutral axis. For Al alloys such as AA6111, AA6016 and the like extensive plasticity occurs and the neutral axis is expected to move during bending. However, very few studies have examined how the neutral axis motion and the strains develop, compared with the mechanics analysis. Geist and Parker (1984) used hardness measurements to investigate neutral axis motion but these experiments did not have the resolution necessary to compare the results with experiment but did indicate neutral axis motion. To understand the nature of plasticity and failure during bending it is important to know the extent of neutral axis motion, the scale of strain gradients developed through the sheet and the maximum strains occurring at the bend surface, finally comparing experimental results with the theoretical predictions. The influence of microstructure on the evolution of strain and failure can then be considered in the context of these parameters. Recently, bending in some automotive Al alloys has been reported mainly from the microstructural perspective (Lloyd, 2000, Lloyd et al., 2002, Mattei et al., 2013) and FEM studies have also investigated the development of plasticity under bending, demonstrating the tendency for strain localization (Becker, 1992, Shi et al., 2014)."

Jan 1, 2018

By Jacek Paraszczak, Stefan Planeta

"RésuméDans la première partie de cet article on discute Ie contexte technico-économique de l'usage des foreuses à l'eau sur béquille dans des mines sud-africaines. Par la suite on présente les résultats d'une étude comparative du forage avec les foreuses à l'huile et à l'eau par rapport aux foreuses pneumatiques. La performance des foreuses est discutée sous les deux aspects: l'aspect technique concernant Ie taux de pénetration et la quantité d'eau rejetee dans les galeries et l'aspect de fa santé et sécurité au travail, et plus particuliérement, les niveaux de bruit et de vibrations ainsi que Ie brouillard de l'huile. On conclut par l'évaluation du potentiel de forage à I'aide des foreuses hydrauliques dans Ie contexte canadien.AbstractIn the first part of this paper the technical and economical aspects of water-powered drilling are discussed. This technology, originally employed in South Africa, received some interest from Canadian mine operators. In this context a comparative experimental study of pneumatic and hydraulic (oil- and water-powered) jackleg drills has been realized. The performance of the drills is compared and the results reviewed with regards to technical aspects (penetration rate, amount of water spilled) as well as health and safety considerations (noise and vibration level, presence of oil mist). The potential for application of hydraulic jackleg drill is discussed."

Jan 1, 1995

"In the present study, the reduction behavior of composite pellets comprising of iron oxide, synthetic graphite and slags were investigated in a laboratory-scale horizontal tube furnace. Two different types of slags indicating silicate base and aluminate base slags were chosen to examine the effect of slag chemistry on the reduction behavior of pellets. Slag composition of binding materials has influences on the reactions occurring in composite pellets during direct reduction. In-situ high temperature visualization approach was used to observe the slag / iron / carbon interactions at 1773K (1500°C). The off-gases were measured by means of infrared analyzer to determine the reaction rates of the pellets. Different physical appearances during the in situ reaction inferred a strong correlation between the slag composition and internal reactions. In addition, compression tests were conducted to examine physical strength of the pellets. This investigation was carried out to establish feasibility of physical property control of pellets by selecting optimum slag compositions of binding materials INTRODUCTIONCurrently, most of the iron ore mines have facilities that make an ore more usable for the blast furnace operation by improving its physical properties (e.g. pelletizing and sintering). However, during the process, a large amount of fuel is supplied to indurate materials which consequently deteriorate energy efficiency and produce more CO2 emission. Along with increased interests, direct reduced iron (DRI) making process; simply without coke oven or sintering process, has opened the era of clean and environmental friendly iron making process. While some of the established DRI technologies such as Midrex and HYL were restricted to certain locations where natural gas is abundant, coal based technologies using Rotary Hearth Furnace (RHF) such as FASMET and ITmk3 have been developed with regardless of expensive fuel deposit. In addition to the direct use of pulverized non coking coal and fine iron ore, RHF process also has advantages of utilizing waste materials such as EAF dust, biomass and recycled plastics. Nevertheless, there are still many challenges in the coal utilizing technologies as the unprocessed coal and the waste materials contain huge volatiles and ashes. Although recent investigations on volatiles in a RHF process (Sohn and Fruehan, 2005, 2006) have indicated the benefits of coal in terms of iron oxide reduction and have shown feasibility of multi-layer process, carbon composite pellets still have disadvantages because of its weak mechanical bonding strength. As the mixed system with carbon and oxides generates intermediate gases (e.g. CO and CO2) between solid particles, it is difficult to keep its physical state without the help of binding materials. In this reason, industries have been tried to use various binding materials such as bentonite, kaolinite and Portland cement. However, they are still struggling to find out new materials that provide not only sufficient mechanical strength but also metallurgical properties, such as porosity, reducibility and swelling throughout the reduction reaction. Recently, Canadian researchers (Aota et al, 2006) observed enhanced mechanical strength of pellets by using high alumina cement as a binder and concluded that the method could be used to recycle EAF dust as well, but in depth mechanism of reinforced strength has not been concerned. Most of the ashes coming from binders formulate certain type of slag during the reduction process due to its incombustibility. Thus, observation and regulation of slag property is an essential for the control of carbon composite pellet. Yet, only a little thermodynamic consideration from the perspective of slag chemistry has been adapted in the iron and steel making industries as ash has been easily ignored for its tiny proportion. In this study, effect of CaO-SiO2- Al2O3 slag system on the reduction of iron oxide was investigated in terms of"

Jan 1, 2012

By T. Kalliomäki, A. T. Aji, M. Lundström, J. Aromaa

The settling properties of anode slime in copper electrorefining have crucial effect on copper cathode quality. Anode slime settling is affected by electrolyte composition and temperature, electrolyte circulation, and the sizes and density of the slime particles and agglomerates. Typically, the industrial copper electrolytes contain 40–60 g/dm3 Cu2+, 130–220 g/dm3 H2SO4, 0.04–25 g/dm3 Ni2+, 0.005–30 g/dm3 As, and have operating temperature of 55–70°C. In optimal electrorefining process, the settling rate of anode slime is sufficiently high to avoid the risk of getting the slime entrapped in copper cathodes. In this research the settling properties of copper electrorefining bottom slimes, mainly consisting of Cu, Ni, Ag, Se, Pb, As, Bi, Sb and Ba compounds, were studied by settling rate tests. The tests were conducted in water and synthetic electrolytes with known viscosities and densities. In addition, the effect of agglomeration was taken into account – it was observed that breaking the agglomerates which existed in the as-received slimes decreased the particle sizes on average 56–73%, which decreased the settling rate. The results of this study provide detailed information of anode slime settling and thus clarify the conditions causing cathode contamination risks in copper electrorefining. INTRODUCTION Settling rates of Cu-ER anode slimes affect the purity of cathode copper and faster settling rate decreases the contamination risk (Davenport et al., 2002; Shi & Ye, 2013). The settling rates are affected by the properties of anode slime particles (Wills & Napier-Munn, 2011; Aaltonen, 2014; Kiviluoma, Aaltonen, Aromaa, Lundström & Forsén, 2016) as well as viscosity and density of the electrolyte (Davenport, King, Schlesinger, Biswas, & Robinson, 2002; Shi & Ye, 2013). Thus, it is crucial to find out how the viscosity and density affect the settling rates. Small spherical particles with diameter below approximately 50 µm obey Stokes’ law (Equation 1) (Wills & Napier-Munn, 2011). v = gd 2 (ρS – ρF) (18η) -1 (1) where v is terminal velocity (m/s), g acceleration due to gravity (m/s2), d diameter of particle (m), ρS density of particle (kg/m3), ρF density of fluid (kg/m3), and η dynamic viscosity (Pa∙s). The approximate effects of kinematic viscosity (ν = η / ρS), density (ρS) and particle sizes on settling rates defined for small anode slime particles based on Stokes’ law are presented in Figure 1. However, Stokes’ law does not take into account other than spherical shapes, and it is only applicable for small particles. Consequently, the real settling rates of the particles are lower than these (Wills & Napier-Munn, 2011). Moreover, some of the anode slime particles are larger than 50 µm (Aaltonen, 2014).

Jan 1, 2019

By Kim H. Shikaze, John R. Hawley

"Even though acid mine drainage is an old problem, particularly in coal mining areas, its appearance in the form of a major environmental hazard in the hardrock mining districts of Ontario was unexpected. The yellow and amber coloured wastes that characterize an acid mine drainage situation were first noted by the Ontario Water Resources Commission in the uranium mining Elliot Lake district. Problems of a similar nature were also noted in the copper-lead-zinc camp at Manitouwadge, the nickel camp at Sudbury and at numerous isolated base metal properties, both in and out of the Province of Ontario.Without exception, when acid mine drainage type effluents were evident, the specific companies involved worked sulphide or sulphide-associated ores. Without exception, the ore bodies contained quantities of iron sulphide (in various mineralogical forms) and, without exception, the milling circuits serving these operations were such that the iron sulphides were rejected to the tailings areas as waste.Once in a tailings area and after a varying period of time, iron sulphides react to form water soluble salts which, when discharged in the effluents from the tailings area, can affect stream chemistry and stream ecology.It is not unusual that the minerals pyrite, marcasite and pyrrhotite (all iron sulphides) react to form a stable oxide under atmospheric conditions. The law of stability of rocks and minerals, for instance, states that rocks and minerals are stable only in the environment of their formation and, as the environment surrounding them changes, the rocks and minerals tend to change to other species which are relatively more nearly stable under the conditions of the new environment (a). Under atmospheric conditions, iron oxide exhibits a greater stability than iron sulphide."

Jan 1, 1971

By D. S. Rogers

"Throughout the history of mining at the Dome, gold has been found in a number of different rock types and in association with a number of different structural settings. Diamond drilling plays an important role in the evaluation of the stratigraphic and structural features which control ore deposition. The main function of diamond drilling is to locate favourable areas of mineralization.To date, over 20,000 diamond drill holes have been drilled from combined surface and underground programs. Needless to say, a great many significant intersections, carrying a wide range of gold values, have resulted from the total of over 756 miles of drill cores which these programs have produced.However, the term ""significant"" takes on new meaning in light of the experience of diamond drilling in a number of ore-type situations at the Dome Mine. Drilling through individual ore veins, such as the Fuchsite Vein or the Quartz-Tourmaline Vein, often intersect the vein structure; however, assays from the veins frequently fail to yield any ore grades. Similarly, drill cores through stringer-type occurrences such as dacite or conglomerate, when assayed, fail to indicate the true size or grade of the orebody ultimately mined.IntroductionOver the years, those who explore for gold and those who have the slightly less fickle task of actually mining gold have shared a common dilemma. That dilemma lies in the failure to relate the results of diamond drill information to a positive ore situation, or ultimately to reconcile ""diamond drill indicated ore"" to actual ore reserve tonnages.Drawing on the knowledge of more than 72 years of mining history at the Dome operation in the famous Porcupine Camp, this paper will review a number of drift and stope situations in which the grades of the ore material extracted will be compared with the anticipated grade of that same drift or zone as calculated solely on the basis of diamond drill assays."

Jan 1, 1982

By G. E. Veins

This paper summarizes an investigation in which beneficiated ilmenite ore was smelted in a continuous, three-phase, 250 kv.a., open-top electric furnace. Minus %. inch ore was smelted, using the standard method. Fine ore, in the order of minus 14 mesh, was smelted in the briquetted form by the open bath method, and in the unagglomerated form by the cold dry-top method. The latter was shown to be superior. The data obtained .are discussed at some length. During the investigation, slag aver-aging 82.5 per cent Ti02 was produced over a period of 87 hours, the maximum being 85 per cent. Such slag should .be particularly attractive for the production of titanium tetrachloride, from which titaniurn metal is produced. The advantages of using paper-mill bark for producing a furnace charge of low bulk density, as required in cold dry-top smelting, were emphasized.

Jan 1, 1957

By Robin Phinney

Certain statements in this presentation may constitute "forward-looking" statements which involve known and unknown risks, uncertainties and other factors which may cause the actual results, pe1formance or achievements of the Corporation, or industry results, to be materially different from any future results, performance or achievements expressed or implied by such forward-looking statements. When used in this presentation, such statements use such words as "may", "would", "could", "will", "intend", "expect", "believe", "plan", "anticipate", "estimate" and other similar terminology. These statements reflect the Corporation's current expectations regarding future events and operating performance and speak only as of the date of this presentation. Forward-looking statements involve significant risks and uncertainties, should not be read as guarantees of future performance or results, and will not necessa1ily be accurate indications of whether or not such results will be achieved. A number of factors could cause actual results to differ materially from the results discussed in the forward looking statements including, but not limited to, the factors discussed in the Corporation's annual information form filed on March 9, 2011. Actual results could differ materially from those currently anticipated due to a number of factors and risks. These include, but are not limited to, the failure to obtain necessary regulatory approvals, including environmental approval, the failure to secure full project financing, the failure to implement the recommendations set out in the Technical Report, the failure to raise financing to implement the recommendations in the Technical Report, risks associated with the mining industry in general (e.g., operational risks in development, exploration and production; delays or changes in plans with respect to exploration or development projects or capital expenditures; the uncertainty of estimates and projections relating to production, reserves and resources, costs and expenses; and health, safety and environmental risks), decrease in potash prices and exchange rate fluctuations. Although the forward-looking statements contained in this presentation are based upon what management of the Corporation believes are reasonable assumptions, the Corporation cannot assure shareholders that actual results will be consistent with these fonvard-looking statements. These fon\?ard-looking statements are made as of the date of this presentation and are expressly qualified in their entirety by this cautionary statement. Subject to applicable securities laws, the Corporation assumes no obligation to update or revise them to reflect new events or circumstances. This presentation is a market update based on the Corporation's public disclosure and does not form a part of any offer of securities, or constitute a solicitation of any offer to purchase or subscribe for securities. Any purchase of securities in the company should be made solely on the basis of information contained in the Corporation's public record which is available on www.sedar.com .

May 1, 2013

By Walter K. (Cory) Conrad

Two pumping tests in the Chilson Member of the lower Lakota Formation were completed at nearly the same location in 1979 and 2008. The 1979 test consisted of a pumping well and several surrounding observation wells penetrating the full 55-m thickness of the aquifer. The 2008 test consisted of a pumping well and three surrounding observation wells screened over 10 m in one of the known uranium ore horizons in the lower portion of the Lakota penetrated only about 3 meters of the more than 55-m thick lower Lakota aquifer. The average transmissivity and storativity values determined from the 1979 tests were 17.6 m2/day and 1.8 x 10-4, respectively. Comparing median transmissivity of 13.9 m2/day and storativity of 1.2 x 10-4 determined in the 2008 test to the 1979 test, the new aquifer parameters for the lower Lakota are respectively about 80 and 70 percent of the 1979 results. Because transmissivity and storativity depend on aquifer thickness, comparing the results suggests that there may be some scaling effect between the tests due to the differing lengths of screened intervals. However, the effect cannot be predicted by calculations such as relative screen lengths or open intervals to the formation, or sandstone versus shale thicknesses on geophysical logs. The scaling effect is attributed to partial disconnection between the lower and upper portions of the Lakota Formation aquifer by locally continuous shale interbeds. Suggestions to resolve this scaling issue are presented.

Aug 1, 2010