Search Documents

By W. A. Alexander

Introduction In the course of a programme of research on beryllium in progress in these laboratories, knowledge of the recrystallization temperature became necessary. As the information is not available in the literature, the determination of this temperature for metallic beryllium was undertaken. By the reduction of grain size through working and recrystallization and the probable simultaneous induction of preferred orientation, it was hoped to improve the working properties of beryllium at lower temperatures. The recrystallization temperature is usually determined by observing the lowest temperature of annealing at which new crystals are formed in severely cold-worked metal or alloys. This temperature is profoundly influenced by the following factors: the purity of the metal, in the case of an element, or the composition of the alloy; the degree of straining or working; the temperature of straining; the original grain size; and the time held at the annealing temperature. The observed temperature is lowered by higher purity, more severe straining, lower temperature of working, smaller original grain size, and longer time of annealing. Beryllium presents special difficulties in that the percent elongation in tension is effectively zero, so that ordinary squeezing or rolling was not possible. A possible means of straining was suggested by the fact that indentation hardness tests could be made. It was known from earlier work that the metal could be worked at elevated temperatures, so that working at the lowest feasible temperature and quenching might also be a means of producing strain. The purity of the metal is also a point of some uncertainty in the case of beryllium. Losano has prepared 99.96% Be which appears to be the best reported. Distilled metal used in the present work approached this purity. However, by analogy with other metals, residual impurities may have a pronounced effect on the recrystallization. Further purification of beryllium would evidently entail considerable difficulties due to the highly reactive nature of the metal, and was not attempted.

Jan 1, 1947

By G. Avramovic-Cingara

Grain boundary characteristics and microstructural evolution are analyzed in a comparative study using orientation imaging microscopy (OIM/SEM) and transmission electron microscopy (TEM/SAD). The subgrain sizes and misorientations were determined by the OIM for aluminum deformed in torsion to equivalent strains between 0.2 and 4 over the temperature ranges of300-600°C and strain rates 0.01-1 s". The OIM gives clearer evidence of boundaries with high misorientation than does TEM, but it overestimates their frequency b y missing boundaries less than 1 0. T EM more clearly reveals low-angle arrays of widely spaced dislocations resulting in finer subgrain sizes than those indicated by OIM. The evidence supports a mechanism combining dynamic recovery (DRY), deformation band formation with permanent boundaries and geometric dynamic recrystallization (gDRX) in contrast to the hypothesis known as continuous dynamic recrystallization (cDRX).

Jan 1, 2004

THE Michipicoten area, one of numerous iron-bearing "Archean" segments in the Shield, contains two main types of iron formation, a normal Keewatin-type, consisting of interbanded chert, siliceous magnetite and jasper, and, gradational to this, a carbonate-sulphide type which contains large de-posits of siderite and pyrite. The carbonate-sulphide type of iron formation bears a direct and intimate relationship to the volcanic development of the area; it there-by affords some insight into genetic problems of Archeanron formation in general. The purpose of this pa-per is to summarize the geological setting of Michipicoten iron formations and to briefly review genetic aspects of recent work in the area. GENERAL GEOLOGY in largely by assorted volcanics and sediments of the Michipicoten series and younger, regional granite masses. (Fig. 1). The Michipicoten series comprises a thick assemblage of mixed flows and pyroclastics together with elastic sediments and banded iron formations. The volcanics belong to the Andesite-Rhyolite Association, and characters-

Jan 1, 1961

By S. Masambi, S. M. Bradshaw, C. Dorfling

The presence of iron in base metal leach solutions complicates nickel and copper recovery processes. Leach solutions are commonly purified by precipitating iron as hematite, jarosite or goethite. Fast oxidation of ferrous to ferric is an important step to remove iron by precipitation at low pH values. This study reviews the ferrous oxidation mechanism and reaction rates in chloride media using molecular oxygen. This work contributes to the development of a better understanding of iron precipitation processing steps, which continues to be an important matter in hydrometallurgy. The specific objectives were to investigate (1) the effect of key process variables (acid concentration, copper concentration, and temperature) on the rate and extent of ferrous oxidation by dissolved oxygen and (2) the oxidation mechanism by varying chloride and hydrogen ion concentrations separately. Batch oxidation tests were performed using synthetic chloride solutions containing 45 g/L Fe and 3 g/L Ni at 50 and 80°C, dissolved Cu concentrations (0.3 to 3 g/L) and HCl concentrations (2 to 4.6 M). Regression analysis indicated that the significance of the effect of different variables on the extent of oxidation achieved after five hours decreased in the following order: HCl concentration > Cu concentration > temperature. Increasing the HCl concentration from 4 M to 4.6 M caused the degree of oxidation achieved after two hours to increase from 58.3% to 98.1%. The catalytic effect of dissolved copper on ferrous oxidation was more significant at low acid concentrations. Experimental data suggest that rapid oxidation of ferrous is possible at high HCl concentrations for two main reasons. First, the formation of ferrous chloride complexes allows ferrous oxidation to proceed without the formation of superoxide as an intermediate product (the rate limiting step in dilute acid solutions). Second, the formation of ferric chloride complexes stabilises the oxidation product.

Jan 1, 2016

By d&apos, F. Elia

Hot cracking of magnesium (Mg) alloys during welding creates a barrier to enhancing the use of these alloys in automotive applications. As a result, it is imperative to understand the mechanisms responsible for hot cracking of Mg alloy welds in order to develop means of eliminating this problem. In this study, the hot cracking susceptibility of AZ91E and AE42 magnesium alloys were assessed using the moving torch Varestraint test method. Plates of 3 mm thickness were extracted from AZ91E and AE42 ingots and subsequently tested. Quantitative cracking data in terms of maximum crack length (MCL) was used for evaluating the cracking susceptibility. Scanning electron microscopy was carried out. The results suggest that AE42 showed a higher resistance to hot cracking in comparison to the AZ91E alloy. This was attributed to the difference in microstructure between the two alloys. In the fusion zone and HAZ of AE42, the brittle needle-like A1IIRE3 phase was seen to decompose to the more ductile particle-like Al2RE phase, thereby increasing the alloy's resistance to hot cracking. In contrast, SEM fractography revealed that brittle A16Mn and Mg17A112 intermetallic particles segregated to grain boundaries and triggered hot cracking in AZ91E.

Jan 1, 2011

By David E. Pearson

"Western Canadian coking coals are located in the Rocky Mountains arid foothills of British Columbia and Alberta. They are typical of non-marine coals, characterized by total sulphur contents of less than one per cent and with ash contents of 10-30 weight per cent. This mineral matter is composed principally of kaolinite and quartz.The petrographic compositions of most of the coking coals which constitute the 2.065 billion tonnes of British Columbia's measured reserves, and the compositions of the metallurgical coal currently exported from Alberta, show them to be rich in the inertinite macerals, macrinite, fusinite and semifusinite. When the mean maximum reflectance of vitrinite in oil/Romax) is used as the coal rank parameter, this high inertinite content is reflected in the lower volatile-matter yields, but the relatively inert character is also displayed by lower free swelling indices (PSI), lower maximum dilatations, lower maximum fluidities and lower coke strengths than other coals of the same rank, but richer in the reactive macerals, vitrinite, exinite and semifusinite. Despite these reduced values in the so-called caking tests, inertinite-rich coals produce strong coke.A system of classification of coking coals is introduced which is based on rank, as indicated by Ro max, and either petrographic composition, maximum dilatation, maximum fluidity or, to a lesser extent, PSI and volatile-matter yield. Six principal coal groups can be distinguished among coking coals using this versatile classification. Inertinite-rich coals are assigned to the Keystone Group (GI), Balmer Group (G3) or Moura Group (G4), each group being named for a coal typical of that population ofcoals. Reactive-rich coals are assigned to the Pittston Group (G2), Kellerman Group (G5) or Big Ben Group (G6). A multiple-regression analysis of coal quality versus price shows how the value of coking coal in the Japanese market appears to be related to reflectance and the free swelling index, and confirms the economic viability of the classification.British Columbia's measured reserves of coking coal contain representatives of four of these groups; Balmer Group (73%), Moura Group (/6%), Pittston Group (3.4%) and Kellerman Group (7.6%).This analysis of the quality of Western Canadian coking coal indicates that despite the need for large proportions of inertinite-rich coking coal in blends produced in the Japanese steel industry, there is nevertheless a demonstrated overabundance of Balmer Group and Moura Group coals available to the international coking coal market."

Jan 1, 1980

By Peter N. Calder, Garston Blackwell

"The history and analysis of a structurally complex open-pit rock slope displacement are described. The failure involved part of the only haulage access to a major ore zone. The ongoing movement was monitored using an electronic distance measuring device and a continuous electronic system specifically designed for the problem. A major fault, infilled with a thick clay gouge, and intersected by other structural features, resulted in the transfer of weight to a rock mass acting as a buttress in the lower regions. Movements were affected by blasting vibrations and ground-water conditions. Remedial measures included limiting blasting levels and lowering the water table, following which mining was successfully resumed in the area.IntroductionBrenda Mines is situated in a mountainous region of the southern interior of British Columbia; the location is indicated on Figure 1 . The elevation is approximately 5000 ft , giving a climate typical of more northern areas. Temperatures vary from -30°C to + 30°C. A snowfall level of 400-800 cm is experienced from November to April. During the spring, a heavy runoff period occurs, increasing the pumping rate in the pit from a nominal 50* gal/min to 2000 gal/min.The orebody occurs in a fractured Jurassic rock mass referred to as the Brenda Stock; it is approximately 3000 ft in diameter and 1000 ft deep. The Brenda Stock was intruded into the Upper Triassic Nicola Group tuffs, breccias and argillites. Mineralization occurred in several stages in a relatively homogeneous quartz diorite host rock. Shearing, faulting and jointing occured later in many stages, producing mineralized clay gouge zones up to several feet in thickness'> , These gouge zones have a major effect on the stability of the pit walls.The structural geology of the pit walls is otherwise relatively simple. Figure 2 is a conventional pole diagram indicating the orientation of the rock structural systems which are present. The major system has an average dip of approximately 70 degrees to the south and strikes approximately east /west , it is not undercu t by the pit slope. Figure 3 is a photograph of part of the North wall on which this system is indicated.The basic pit design consists of a working bench height of 50 ft, with a final wall height of 100 ft between berm s and a 100-ft-wide berm every second lift. Combined with a local face slope of 50-70 degrees, the resulting wall slope, not including haulage roads, is 45 degrees. Figures 4 and 5 are generalized plans and sectional views of the pit."

Jan 1, 1980

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed.The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grade, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the final cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure I."

Jan 1, 1995

By H. Soto, P. Lacombe, R. del Villar

"During the summer of1989, Les Mines Selbaie, with the cooperation of Université Laval initiated a research project to evaluate the column flotation technology for its concentrator near Joutel, Quebec. The experimental work involved both a 5 cm by 11 m laboratory column and a 45 cm by 10 m home-made pilot unit Amenability tests were conducted using both units on various streams of the plant. Results showed that columns are not suitable for the copper cleaning circuit because the loss of precious metals, associated with the rejected pyrite, overcome the improved copper metallurgy. On the other hand, column testing at the zinc circuit showed improved zinc selectivity.Scale-up testing was', therefore, conducted on the first zinc cleaner concentrate using the laboratory-size column. The influence of variables such as porous parger grain size, wash water flow rate, airflow rate and froth depth values on column performance was' first assessed. Scale-up parameters were then determined using the optimal operating conditions from the previous tests. Simulation facilitated the determination of the most convenient plant-scale column arrangement.A number of conclusions concerning the experimental determination of scale-up parameters are also presented."

Jan 1, 1993

By Sudarshan Martins

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By S. L. Gula

"Effective and timely communication during routine operations, and especially during emergency situations, is no easy task in any underground mine. At Cominco Fertilizers, Potash Operations, where 150people are employed underground to produce 3.1 million tonnes of potash per annum at a depth of 1100 m (3600ft), this is no exception. The over-all mine workings underlie an area of approximately 20 km 2 with average travel time to the active mining areas being approximately 30 to 40 minutes by light vehicle, and significantly longer than this for heavy equipment.In a mine of this size, the deployment and management of personnel and materials on a day-to-day basis, and during mine emergencies, is an important exercise. The Personal Emergency Device (PED) system has provided the Potash Division a means to achieve improvements in this area and reduce the communications bottleneck.The MineAt Cominco Fertilizers Potash Operations, approximately 30 km southwest of Saskatoon, the orebody is the same horizon being mined by other potash producers in the Saskatoon area and extends over 300 km in an east-west direction, and approximately 150 km in a north-south direction. Mining operations are carried out with approximately 150 employees operating on a continuous-shift basis, seven days a week.Mining is presently being done from Block 6 which takes the mine to its northernmost boundary and contains reserves of approximately 50 million tonnes. Production is from one level by five twin rotor continuous mining machines, each capable of cutting a face up to 5.5 m wide and 3.3 m high . All ore is transported to the shaft via approximately 20 km of conveyor where it is removed to surface by two 24 tonne skips.After the ore is conveyed to the mill for processing, the finished product is shipped by rail car or trucks to other parts of Canada, the United States or through Vancouver to other parts of the world."

Jan 1, 1993

By Ross I. Kelly

Carbonate rocks are widespread throughout Ontario and provide raw material for more uses than perhaps any other rock type. The principal carbonate rocks that are used by industry in Ontario are Paleozoic era limestone and dolostone. Limestone is a sedimentary rock that is composed mainly of the mineral calcite (CaCO,) while dolostone, also a sedimentary rock, is composed mostly of dolomite [CaMg (CO,),l. The majority of the province's limestone and dolostone extraction occurs from Paleozoic era rocks located in southern Ontario. Calcite and dolomite are also found in Precambrian marbles, calcite veins and carbonatites, however, utilization of these rocks by industry has been less common. Calcite and dolomite-rich rocks are utilized for a wide variety of uses including raw materials for cement and lime manufacture, chemical and metallurgical stone, fillers and construction aggregates (Derry, Michener, Booth and Wahl and OGS 1989a). For some uses chemical and physical requirements are very important. In the manufacture of glass, for instance, the chemical requirements of source materials are very important and very stringent. In other uses physical criteria such as whiteness may be more important. Although carbonate rocks are quite plentiful within the province, deposits that contain high concentrations of calcite or dolomite are somewhat limited. For that reason, this paper focuses on deposits that are known to, or may contain, a high percentage of calcite and/or dolomite. The paper emphasizes potential sedimentary limestone and dolostone resources, as these are the carbonate rocks most commonly utilized by industry in Ontario.

Jan 1, 2001

By Joachim von Scheele

An oxyfuel-based technology - OXYFINES - has been introduced for in-plant recycling. It provides fines, dust, sludge (without any drying-step) and other by-products arising in the steel and metal producing industries to be recycled directly back into existing processes or a separate unit on-site. Results from full-scale installation (20,000 tpy) for dust treatment, full-scale and pilot-scale trials with dry and wet materials in the steel and ferroalloy industries are presented. Processing rates at 3.5 t/h have been demonstrated. The product is agglomerates or lumpy pieces, the latter if the product has passed an all-liquid stage and thereafter been crushed. The technology does not only provide a solution to the problems connected to dust and sludge generated in metal production. It also turns these materials into a low-cost raw material useful for the production in question, thus replacing part of the raw material input in electric arc furnaces, blast furnaces, etc. Elements harmful to re-use of the processed dust or sludge, e.g., zinc and alkaline components in steel production, are removed as secondary dust, and material yield of main components for re-use is very high, about 98%. The paper reviews the concept, the results obtained and its status; its use for sludge recycling is emphasized.

Jan 1, 2004

By Clyde Williams

If you would allow me some liberties, I would re-state the title of this talk as Scientific Research, Our Greatest Resource, because that title would represent more clearly a present-day conception of the metals and minerals situation. It is a subject worthy of careful consideration. Canada and the United States are so similar and interdependent in their national economies that, in the following discussion, examples of conditions in the United States may? be interpreted to apply to Canada as well. Moreover, it is a striking fact that the per capita value of mineral production in Canada and the United States in 1940 was almost the same. Therefore, in the consideration of this subject, I have made no attempt to differentiate between the two countries. The consumption of the world's mineral resources in the last few decades, and particularly during World War II, has been so enormous as to require some form of magic to ensure the continued progress of civilization in the face of a diminishing supply of these resources which are so critically essential. As Dr. C. K. Leith pointed out in 1941, industrial expansion has been so great that, during the first forty years of this century, the world used more of its mineral recourses than in all preceding history. And this did not include the all-out consumption during the succeeding five years of war.

Jan 1, 1947

By E. Mohammadi Zahrani

In this study, Mg-doped fluorapatite (Mg-FA) nanopowders were prepared through a sol-gel, technique and characterized. Designated degree of Mg2+ ions incorporation into the apatite structure was indicated by the x value in the general formula of (Ca10-xMgx (PO4)6F2), where x=0, 0.25, 0.5, 0.75, and 1. XRD, AAS, FTIR and TEM techniques were utilized to characterize the synthesized nanopowders. In vitro bioactivity of the powders was evaluated in simulated body fluid. Powders had a crystallite size less than 100 nm. It was concluded that Mg-substitution could alter bioactivity and dissolution behaviour of Mg-FA. These two parameters were proportional to magnesium content of the powders.

Jan 1, 2010

By Mel Owen, Bob Tipman

"A number of studies have identified the presence of heavy minerals in the Athabasca oil sands. A 1996 Mineral Development Agreement study into the recovery of Co-Products identified low operating costs, a simple flowsheet and access to market as key drivers in advancing interest in a viable project.Commercial bitumen extraction processes recover 50% of the titanium heavy minerals and 85% of the zircon into froth containing 1 % of the feed solids. Froth treatment tailings grade is 11.5% Ti02 and 3.6% Zr02.Processing this high grade feed in a combination of flotation, roasting, screening, gravity concentration and magnetic separation, results in concentrates of rutile, leucoxene, ilmenite, zircon and rare earths of marketable quality.A combination of high grade feed and a simple process lead to operating costs among the lowest in the industry. Low cost heavy minerals and low energy costs indicate an intriguing potential for low cost pigment production in Alberta. The production of heavy minerals from oil sands remains one of the largest untapped resources in the Province of Alberta1.0 IntroductionThis paper describes the results of an investigation into the recovery of heavy minerals from tailings produced by the major oil sands plants. The study was carried out under a Canada-Alberta Mineral Development Agreement (Alberta Chamber of Resources 1996). The MDA Co-Products Study examined the potential for the economic recovery of heavy minerals from oil sands tailings."

Jan 1, 1998

By Yan Qun, Chen Xiao-ming, Ma Pei-long, Luo Xian-ping, Luo Cai-gui, Feng Bo

The effect of leach promoting reagent LPF on the leaching process of a weathered crust elution-deposited rare earth ore has been investigated and the mechanism is discussed. The result shows that the leach promoting reagent LPF can enhance the leaching extraction of rare earth ore effectively. With the addition of LPF to the lixiviant at a concentration of 0.1%, the leaching extraction increased by more than 8%, the ammonium sulfate concentration could be decreased by 25%, and the leaching liquid/solid ratio reduced by 34%. The mechanism analysis shows that LPF can react with rare earth ions and form soluble coordination compounds, thus reducing the activity of the leached rare earth ions, increasing the concentration difference for ion diffusion, and promoting the rare earth leaching process. These results will hopefully help point to a new approach to making the leaching process of low-grade weathered crust elution-deposited rare earth ore more efficient and with lower lixiviant consumption.

Jan 1, 2014

By N. Nemeth

A brief summary of available filtration research is given. Its usefulness and shortcomings to practical application are examined and suggestions for new avenues of research outlined.

Jan 1, 1967

By F. Ford, Z. Dai, A. W. Lee

ABSTRACT: As high-grade nickel sulphide ores are being depleted and processing laterite ores continues to pose challenges, the future of nickel extraction lies in low-grade ultramafic ores. Canada has large resources of low-grade ultramafic nickel sulphide ores in the Thompson Nickel Belt. Most of the deposits are high tonnage and open pittable, but have high MgO content. The main challenge in processing low-grade ultramafic ores is the presence of serpentine. Chrysotile, one of the three polymorphs of serpentine, is the most common form of asbestos. In addition, the high slurry viscosity associated with ultramafic ores makes grinding and flotation possible only at a very low solids percentage.

Jan 1, 2011

By J. Drelich

We report structural forces measured for 10 nm silica particles deposited on alumina substrate and 5-80 nm alumina particles on mica using atomic force microscopy technique. For nanoparticles forming clusters, oscillation of structural forces was recorded with a periodicity that is close to the size of the nanoparticles used. Additionally, selected force-separation results indicate that the forces involved between the AFM probe and individual nanoparticles can be studied using the nanoparticle-coated substrates.

Jan 1, 2006