Search Documents

By Jakob Janzen

This paper demonstrates that the introduction of a Battery Energy Storage System (BESS) into an isolated diesel generator based grid has the potential to reduce the electricity cost and deliver a good return on investment. Energy storage also allows for increased renewable energy penetration, into the isolated grid, that further reduces the electricity cost. The isolated power system studied includes several diesel generators of different sizes. The typical operating pattern is for the generators to be run at 80% to 85% of their power rating to deal with load fluctuations. Operating the diesel generators near their full power rating, however, improves their efficiency, in this case, while the frequency and load control can be carried out by the BESS. Operating the diesel generators near their full power rating reduces the number of generators which need to be operating to support a given load. As a result, the improved efficiency of the diesel generators and reduced maintenance cost, for operating fewer machines, are the reason for the savings.

Aug 1, 2013

By J. Hoover

"IntroductionThis chapter will discuss the operational and maintenance aspects of a heavy media cyclone circuits as applied to coal processing and using magnetite as the media. It deals with heavy media bath separators in terms of types of media, equipment, circuits, media recovery, maintenance, and product handling. It will detail heavy media cyclone operation and supplement the previously described topics.The heavy media cyclone was first developed in the Netherlands by the Dutch State Mines in 1945. A cyclone plant was not built in North America until 1961. Traditionally, heavy media cyclones have been used to treat size fractions between 1lz in. (12 .6 mm) and 35 mesh (0.5 mm). High maintenance related to heavy media bath separators has recently prompted some plants to crush all raw coal to minus 2 in. for treatment in heavy media cyclones.The heavy media bath separators utilize only the force of gravity to make the separation between heavy and light particles. This requires lengthy retention time which can lower capacity and also is inefficient for finer particles. A heavy media cyclone utilizes centrifugal forces which are 20 to 200 times greater than the force of gravity. This means the separation between coal and the impurities occurs very quickly, therefore a low retention time is required allowing cyclones to have high tonnage capacities. Also these greater forces allow better separation for the finer particle sizes.Heavy media cyclones are now widely used to produce both metallurgical and thermal coal. Work is in progress to reduce magnetite consumption, extend wear life, increase tonnage capacity, improve separation efficiency and automatically control these cyclone circuits."

Jan 1, 1989

By F. Hassani, E. Aflaki, M. Nokken, M. Kermani

"This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill consists of tailings, different binders such as Portland cement, fly ash and blast furnace slag and an alkali activator such as sodium silicate. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. The influence of sodium silicate concentration, pulp density and mixing time on the mechanical properties of samples were evaluated using the uniaxial strength test. Mercury intrusion porosimetery (MIP) was used to analyse the microstructure of CHF and Gelfill samples.This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Mixing time strongly influences the mechanical properties of Gelfill samples but did not have any effect on CHF samples. (iv) The MIP analyses indicate that the pore size distribution and total porosity of Gelfill and CHF were different, and this did contribute to higher strength development of the Gelfill samples. INTRODUCTIONThe increased depths of mines in the Canadian Shield and the high stress associated with these depths favour a new method of mine backfill that can both meet strength requirements and help mine productivity. The mine backfill mainly consists of tailings, water and binder materials, the latter being most expensive. Gelfill is a new mine backfill material whose binder usually consists of alkali activators such as sodium silicate and other cementitious materials such as blast furnace slag and normal Portland cement. Although sodium silicate has been used in concrete manufacture, the use of this material in mine backfill is relatively new (Doucet, 2007, Razavi, 2007). Until very recently there have been only a few isolated publications, mostly out of McGill University, regarding mine Gelfill (Razavi, 2007 and Kermani et al., 2009 and 2010). These papers have investigated some of the basic mechanical properties and mechanical behaviour of Gelfill. However, the physical performance of Gelfill in various conditions has yet to be understood. Therefore, the main objective of this study was to investigate the influence of mixing time and sodium silicate concentration on the mechanical performance of Gelfill and CHF through a series of experiments. Moreover, the microstructure of the Gelfill and CHF samples was studied."

Jan 1, 2015

By Gilles Carrière

"The Huntingdon mine of Quebec Copper Corporation is situated 3 miles south of the village of Eastman, in the Eastern Townships of Quebec. The copper deposit consists of several pyrrhotite-chalcopyrite replacement bodies or bands.The first mining operations on the conspicuous surface gossan of the Huntingdon deposit started in 1865. They were suspended in 1883. The .mine was again active from 1890 to 1893 and from 1912 to 1924. These operations were carried to a depth of 500 feet, and it is estimated that some 150,000 tons of ore were extracted, of a grade reported as varying between 3 Yi and 7 per cent copper.In 1950 a program of exploration was initiated in the area of the old mine, and resulted in the finding of 500,000 tons of ore with a grade of 2 per cent copper. A new shaft was sunk to a depth of 1,160 feet, and by February 1954 the mine was extracting 800 tons of ore daily.General Geology and StructureThe mineralized zones are on the west side of a band of altered volcanic rock, locally called andesite, adjacent to a sill-like body of serpentinized peridotite which lies west of the andesite. The bands of andesite and serpentine extend several miles north and south of the mine. Their strike is generally north 15 degrees east, and they dip steeply east. Their widths vary very considerably along the strike, but in the mine area each is about 450 feet wide on surface. They are enclosed in sediments of the Caldwell series, consisting of greywackes, quartzites, slates, and shales. The andesite belongs to the same series, which is thought to be of Cambrian age (1). The ultrabasic intrusive is post-Ordovician.At p\aces along the serpentine contact the andesite shows a pronounced schistosity; it is parallel to the contact and rarely extends farther than a hundred feet from it. No evidence of strong folding or faulting has been found so far in the mine workings. Some apparent distortions and irregularities in the strike of the contact may all be due to the intrusive nature of the serpentine. In the mine area, transgressive tongues of serpentine point southward in the andesite.A few vertical lamprophyre dykes, not more than five feet thick, cut the other formations at right angles."

Jan 1, 1949

By A. Warczok

The mechanisms and kinetics of copper oxidation and reduction have been investigated in small scale thermal gravimetric experiments as well as in laboratory pilot scale, packed bed reactors. With blister copper flowing gravitationally down through a packed bed of ceramic particles, counter-current to low oxygen containing combustion gases, the rate of oxidation was found to be very high due to the large surface area created. Similarly, reduction by flowing copper through a packed bed of charcoal lead to rapid de-oxidation. Based on these laboratory measurements, fundamental rate data have been obtained. Modeling of industrial sized packed bed reactors using the laboratory results, opened up the possibilities of developing a new, very intensive, continuous process for copper fire refining. The developed mathematical model together with a computer process simulator, allowed for the design of the industrial-pilot installation to be built and tested at the ENAMI Paipote smelter in Chile.

Jan 1, 2007

By Sukumar Bandopadhyay, Arunapuram Sundararajan

"Unique production and environmental problems are associated with multiple seam mining where dragfines are used for overburden and interburden removal. On the production side, the problems are decreased dragfine efficiency in chopdown operations, the general need for spoil rehandle, complications in sequencing stripping and coal handling operations, and potential stability problems in highly stacked spoil. Many variations of dragline methods have been reported in the literature to encounter these problems. Because of the physical properties and peculiar hydrology of sub-arctic region mining of multiple seams in such areas probably could not be done with the methods used in temperate regions.The properties of thawed material would make spoil hard to place in a stable manner and thus would influence the mini sequence. For instance, multiple seam mining which requires some rehandling of spoil and prolonged exposure of overburden and interburden material might be precluded by the instability of thawed spoil and therefore mining techniques have to be modified. Since the deployment and operation of a dragline in modes different from conventional schemes will affect productivity, it will be necessary to study the effects on production of changing the dragfine operational schemes. This paper presents a heuristic simulation model of multi-seam dragline operation of a sub-arctic mine that can be used to analyze the handling of overburden and detailed study of the dragfine performance."

Jan 1, 1986

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter in blowing the copper stage has been developed to predict the molten temperature. The key assumption of the model was that white metal and gas phases in the converter were in thermal and chemical equilibrium. In this model, the chemical reaction of white metal and oxygen was accomplished completely. So long as sulfur existed in the bath, the generation of Cu2O was frozen. The reaction rate was considered to be constant and controlled by the reacted sulfur. The converter temperature was calculated by heat balances over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depended on process parameters such as oxygen efficiency, molten emissivity and oxygen enrichment.

Jan 1, 2007

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, N. Andrade

In this work, the age-hardening behavior of cast Al-Si base alloys was investigated. It was found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu-Mg alloys. TEM observations reveal that the age-hardening behavior is related to the precipitation sequence of the alloy. For the Al-Si-Cu-Mg alloy, the first aging peak is the result from the high-density GP zones, while the subsequent are from metastable phases. The transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks.

Jan 1, 2006

By M. E. Holter

"Limestone-bearing strata are exposed in seven areas of Alberta, each situated adjacent to rail and road facilities. Six of these centers are located along the eastern edge of the Foothills and Front Ranges of the Rocky Mountains in western Alberta. The other is in northeastern Alberta, along the eastern margin of the Alberta Basin. High-grade limestones are present in Middle Cambrian, Upper Devonian and Mississippian strata. Middle Cambrian (Eldon Formation) limestones have been exploited only in the Exshaw area west of Calgary, where they formerly were used for lime production. Limestone beds of the Upper Devonian Palliser Formation are exploited at Exshaw and at Cadomin in west-central Alberta for the manufacture of cement. Reserves of high-grade limestone also are available in the Palliser Formation near Crowsnest Lake in southwestern Alberta and near BrUle, west of Edmonton. Upper Devonian limestones of the Waterways Formation are widespread in the Fort McMurray area of northeastern Alberta, but available data indicate they are of inferior quality to the limestone deposits of the Rocky Mountains regions. The Mississippian Livingstone Formation contains large reserves of high-grade limestone at several localities in the Rocky Mountains and Foothills. Commercial development of the unit is now underway at Crowsnest Lake and at Exshaw for lime production, and future exploitation of these beds is feasible at Blairmore and Nordegg."

Jan 1, 1973

By I. M. Masters

Iron removal and control in processes employing pressure leaching technologies developed at Dynatec Corporation are reviewed. Discussions are focused on recent developments in the processing of nickel-copper matte and copper concentrates, and on the Ambatovy laterite project in Madagascar. Iron control and its implications on flowsheet design in the pressure acid leaching (PAL) treatment of laterite ores and in the oxidative pressure leaching of mixed nickel-cobalt sulphide intermediates are also discussed.

Jan 1, 2006

By N. Staroselsky

"Significant energy savings are often possible for centrifugal compressors operating in parallel by improved control strategy and improved instrumentation. Blow-off can usually be reduced by improved surge control combined with a better control strategy for loading and unloading the group of machines. More precise and stable pressure control then becomes possible. This improved control strategy will also decrease the frequency of operation near the dangerous limits of surge or overload or overspeed. A sample station of mixed centrifugal and reciprocating compressors is examined and a substantial energy saving with the recommended control strategy is projected from operating data. Present Operating Conditions of the Compressed Air StationThe Compressor StationThe compressor station described here has three centrifugal compressors and three reciprocating. It supplies a mine in New Brunswick.Compressed Air and Power ConsumptionFigure I and Figure 2 provide graphs of air consumption and pressure changes based on the owner's data.During the typical two-shift operating day (Fig . I) in the non-productive shift (midnight to 8:00 a.m.), the consumption stays at a level of 9,000 SCFM. This corresponds to a pressure of 110 PSIG. Then, after 8:00 a.m ., the air consumption starts to increase and th e pressure decreases. Around 10:00 a.m., the consumption reaches its maximum level at 97 PSIG. Around II :30 a.m., the air consumption starts to decrease because of the production drop during the lunch break of the first shift. Pressure increases again up to 109 PSIG. After the break, consumption rises to its maximum level over 16,000 SCFM andpressure drops to 97 PSIG.Around 2:30 p.m., the air consumption drops sharply to 9,000 SCFM because of the production decrease to zero level. This drop results from changing of shifts. The pressure at this time increases again up to 110 PSIG. The second shift (2:30 to II :30 p.m.) is an alogous to the first.During the three-shift operating day, the break around 4:00 . a.m . and the shift change around 6:30 a.m. cause sharp drops in air consumption. The pressure for almost the entire night shift stays near 110 PSIG because the station is working with blowing-off even under the maximum consumption. The analysis of Figures I and 2 shows that the pressure varies with the air consumption changes. During non -productive time (non-production shifts , shift changes and breaks) or during the night shift, the total station capacity is proportional to the discharge pressure. By decreasing the level of this pressure up to 97 PSIG, the flow of the station may be decreased during the non-production time as follow s:"

Jan 1, 1980

By A. Kobzhanov, S. Saparova, S. Brochot, D. A. Mango

KATCO (an ORANO Mining and Kazatomprom joint venture) is the largest in-situ leach uranium mining operation in the world, exploiting the Muyunkum and Tortkuduk uranium deposits in southern Kazakhstan. After extraction from the deposits, uranium is then transported via a hydraulic network to be purified in three processing plants located near these deposits. Within KATCO, with the support of ORANO Mining and CASPEO, in 2018 and 2019, a large project that had as its main objective to improve the uranium accounting system was implemented. The objective of this paper is to describe this project and all the changes that it entailed. At KATCO plants, a black-box approach was previously used for uranium accounting. However, it is recommended to use all the available measurements and to deploy a data reconciliation model (between well-fields and plant) as the reconciliation uncertainty is overall lower and it provides a more accurate uranium balance. During the deployment of this project, the rules and algorithms to generate the uranium accounting report, the associated flow diagrams (for uranium accounting), the streams, units of operation, stocks, reporting and Key Performance Indicators calculation rules were re-defined.

Jan 1, 2020

By M. Mirnezami, J. A. Finch, M. S. Hashemi A.

The surface of -30µm silica suspension (2% v/v) treated with 100 ppm Mg2+ at pH 11 was fully coated with Mg(OH)2. Under this condition, the silica is strongly positively charged (+30 mV) and the suspension is dispersed. Subsequent addition of Ca2+ promoted aggregation and reduced the surface charge. At this pH calcium is present as Ca2+ and CaOH+, i.e., positively charged ions interacted with the positive surface. Aggregation by a chemical bridging mechanism is proposed. The observation may be relevant to the widespread practice in mineral processing of adding lime to promote aggregation and settling in concentrate thickeners.

Jan 1, 2004

By L. A. Melis, J. W. Rowson

"Cluff Mining has successfully operated a gold recovery plant at its Cluff Lake operation in northern Saskatchewan to recover gold f rom Phase 1 uranium leach tailings. The operating circuit consists of tailings repulping, grinding, cyanidation, carbon-inpulp, gold recov ery, and cyanide destruction by acidification, volatilization and re-neutralization. The process is described and operating data and metallurgical results from the operation are provided.INTRODUCTIONCluff Mining, a Saskatchewan partnership, is owned 20 per cent by Cameco and 80 per cent by Amok Ltd. /Ltée. (Amok), manager and operator of the partnership.The current operation includes the Phase II uranium mining and milling facilities, located at Cluff Lake, 700 km north of Saskatoon, capable of processing 300 000 tonnes o f ore to produce about 4 000 000 lb UPs (1500 tonnes of uranium) per year.The Phase I operation was initially established to process the very high grade ""0"" uranium orebody from 1980 to 1983. The leach tailings from the Phase I mill operation were found to contain elevated level s of gold . These high gold values were partially due to the gravity pre-concentration step included in the uranium recovery circuit, and to the naturally high levels of gold associated with the uranium mineralization in the""0"" orebody .During the Phase I operation some 6475 tonnes of leach tails were produced and stored in a total o f 2916 large concrete containers (vaults). This method of storage was, at the time, deemed to be the preferred method of temporary storage for the tailings.This temporary storage of high-grade gold tailings facilitated the reclamation and reprocessing of the leach tail s for gold recovery. The primary reason for reprocessing the Phase 1 leach tails was to provide for long-term permanent disposal of the material as an admixture with Phase II tailings in the Cluff Lake tailings disposal area. Although there was limited tonnage, the high gold content in the material made the in stallation of a gold recovery circuit economically justifiable."

Jan 1, 1989

By B. R. McEwen, A. N. Samis, J. H. Gray

"The Quebrada Blanca Copper Mine is an open pit copper project located at 4200 m elevation in the Chilean Andes. The deposit is a world-class supergene enriched porphyry with a mining reserve of 89 Mt of 1.3% copper. The supergene zone will produce 6.3 Mt of ore per year for more than 15 years to produce 75 000 t of cathode copper per year.This paper will review the project geology the computer model ling of the deposit, the mine planning process and the property production scheduling. With copper production .fixed by the onsite electrowinning capacity, the planning and scheduling aspects to optimize the project NPV will be discussed. Some of the logistics, equipment. personnel and process difficulties of operating a mine at 42()() m elevation will also be described. IntroductionProject DescriptionThe Quebrada Blanca Copper Mine is an open pit copper project located in the northern part of the Chilean Andes. The project is based on the supergene enriched portion of a porphyry deposit which has a mining reserve of 89 million tonnes at 1.3070 copper. Below the enrichment blanket, the protore represents a further resource.All ore will be leached, the higher grade material will be crushed and stacked for thin layer heap leaching, and the lower grade and oxide material will be dump leached as run-of-mine material. Solvent extraction and electrowinning will be used to produce 75 000 tonnes of cathode copper per year. Power will be supplied by a 40 MW on-site diesel generating plant with the waste heat being used for process heating. The leaching operation will operate in excess of 15 years and may be followed by open pit mining and conventional ore concentration of the underlying primary sulphide mineralization.Because of the dry location water will be piped 37 km from a ground water source at the Salar de Michincha. Water requirements will be approximately 1.5 million m3/year. The operation will eventually employ approximately 550 people on a 7-day-on, 7-day-off rotation with two twelve-hour shifts per day with an on-site camp. Busing will be provided to the port city of Iquique."

Jan 1, 1994

"Since the publication of a literature review on this topic (McIvor and Finch. 1986), the author has been involved in more than thirty rod milling efficiency tests at seven different milling operations. There have also been several interesting additional articles on rod milling found in the literature. This update describes the most important findings from investigations carried out since the previous review, as well as developments in the techniques used to evaluate the grinding efficiency of rod mills.Rod Mill Power DrawA series of power draw versus charge level measurements were taken on the rod mills at Leg Mines Selbaie and Kidd Creek Mines Limited (McIvor. 1989). These revealed a significant (about 10070) loss in power draw with the installation of new liners, a common observation among rod mill operators. This loss in power draw depends on the liner design, particularly the average thickness and lifting face profile of the new liner. The theoretical power usage of both mills was approximately 5070 lower than that given by the Allis-Chalmers power draw formula (Rowland. 1982).The shape of the power draw versus charge level curve suggested an opportunity for reducing media consumption. By increasing mill speed, power draw could be maintained with a smaller mill load, most significantly for mills operating with high charge levels. Analysis of data from 62 installations confirmed this (McIvor, 1989). On average, a 10 percentage point increase in critical speed results in a 15070 in specific media consumption (Le. kg of steel consumed per kWh of energy consumed). Table 1 lists a number of relatively high speed rod milling installations. No negative effects on the drive train, liner life, or the tendency for rods to tangle have been reported. A reduced lifting angle of the new liner leading face (e.g. 45 versus 90 degrees from the mill perimeter) is recommended for higher speed rod mills (Leclerq, 1990)."

Jan 1, 1995

By J. J. O?Neill

Introduction The Beattie mine is the first of its character to be exploited in Quebec. It is primarily a large low-grade gold deposit containing values which a few years ago would not have been considered as ore. Much interest is attached to this development as its success may mean a greatly enlarged scope to gold mining in Canada on deposits which have formerly been considered worthless. Because of its potential importance as a pioneer in low-grade gold mining, the Quebec Bureau of Mines decided to make a careful detailed study of the Beattie in the hope not only of assisting in its development, but of stimulating the search for similar essential geological conditions in other parts of the Province. This paper is a summary of the results obtained during two months on the property in 1932, supplemented by a few trips underground in 1933. The full report will appear in the Annual Report of the Quebec Bureau of Mines for 1932, Part C. Location and Means of Access: The Beattie ore-body is situated two miles west and one half mile north of the centre of Duparquet township, and approximately 22 miles north 28° west of the town of Noranda. Until the fall of 1932, access to the property was from LaSarre, on the Canadian National railway, over a thirty-mile water route with one portage 600 feet long; about 2,000 tons of machinery and supplies were taken in by that route. An automobile road, nine miles long, now connects the property with the Makamik highway, and a narrow-gauge railway, without ballast, gives outlet for concentrates from the mill to the C.N.R. tracks of the Rouyn-Taschereau line, nineteen miles distant.

Jan 1, 1934

By K. Soga

DOWA has long been specialized in the treatment of complex massive sulfide ores from exploration through smelting. Its competitive advantage derived from ore dressing technology to dress and concentrate complex ore to various kinds of metals concentrates. With this technology, the company recovers as many as seventeen different nonferrous metals. Therefore, it is crucial for the environment management and recycling business both to recover valuable elements like gold, silver, copper etc. and to handle hazardous elements in safety. From this view point, the nonferrous metal industry has a potential to play an important role; that is "The Anchor of Recycling" or "The Joint of Recycling Loop". By utilizing these mining, smelting and refining technologies, know-how and facilities, DOWA became a leading waste treatment, soil remediation and metal recycling company in Japan. This knowledge is now being applied in China .

Jan 1, 2007

By Trygve Høy

"Important stratabound lead-zinc deposits in southeastern B. C. occur in rocks that range in age from Proterozoic Helikian to Middle Cambrian. The Sullivan deposit, and similar but smaller deposits in the Sullivan area are the only important deposits that occur in clastic rocks with little carbonate content. The highly deformed and metamorphosed Shuswap deposits, of probable Hadrynian to Helikian age, are in mixed marble, calc-silicate gneiss and pelitic schist assemblages, rocks transitional between clastics and carbonates. Deposits in younger rocks, such as the Kootenay Arc deposits in the Lower Cambrian Badshot-Reeves Formation and the Monarch -Kicking Horse deposits in Middle Cambrian dolomite, are hosted by platformal carbonate rocks.An important regional control for the distribution of deposits appears to be a northeast-trending tectonic zone that crosses the Rocky Mountains and the Purcell Mountains just south of the Sullivan area, and projects southwestward toward the Salmo camp at the southern end of the Kootenay Arc. Pronounced northeast-trending gravity and magnetic anomalies, basic volcanism of Hadrynian age (the Irene volcanics west of Creston) and a preferred alignment of Mesozoic granitic rocks indicates that the zone coincides with deep crustal structures. Within the zone are dramatic and abrupt thickness and facies changes in Hadrynian Windermere rocks and lower Paleozoic rocks, and on the east side of the Rocky Mountain Trench in Helikian Purcell Supergroup rocks, indicating that block-faulting was active intermittently within the zone from Helikian through to lower Paleozoic time. Right-lateral and reverse movements occurred on northeast-trending tear faults within the zone in Mesozoic time."

Jan 1, 1982

By J. Groppo, W. Zhang, R. Honaker

"The flotation of monazite is depressed when using hydroxamic acid as a collector in the presence of calcium ions which may exist due to the dissolution of minerals such as calcite. Minor dosages of sodium hexametaphosphate (SHMP) were found to effectively depress calcite, whereas the flotation of monazite was not impaired in single mineral flotation tests. However, in a mixed mineral flotation system, monazite flotation was depressed significantly. The mechanism of hydroxamate adsorption on monazite and calcite, the depression mechanism of calcite on monazite, as well as the depression mechanism of SHMP on calcite and monazite were studied using micro-flotation, electro-kinetic, and adsorption tests. Findings indicate that the adsorption of hydroxamate on monazite was due to chemisorption while adsorption on calcite was a result of physical interaction. SHMP significantly increased the negative charges of calcite surfaces which depressed the adsorption of the hydroxamate anions on the calcite surfaces due to an elevated electrostatic repulsion force. When calcium-rich minerals such as calcite are mixed with monazite, the calcium ions dissolved from the mineral surfaces specifically adsorb onto the phosphate oxygen sites on the monazite mineral surfaces thereby causing depressing effects. The addition of SHMP to suppress collector adsorption on the calcite surfaces interacts with the calcium species that were specifically adsorbed onto the monazite surface, which prevents hydroxamic acid adsorption onto the rare earth oxygen sites due steric hindrance and results in the flotation depression of monazite. INTRODUCTIONAs one of the commercial rare earth ores, monazite has been widely exploited to produce additives for catalysts, batteries, alloys, etc. Because of the complexity and the fine nature of some monazite ores, methods such as gravity, magnetic, and electrostatic separation to treat beach sand monazite fail to produce satisfactory concentrates, suggesting the use of floatation is warranted (Cheng, Holtham, & Tran, 1993). The primary associated minerals of monazite ores include ilmenite, quartz, zircon, rutile, sillimanite (Dixit & Biswas, 1969; Pavez a& Peres, 1994, 1993). Using sodium oleate as collector for monazite has been reported in many studies (Cheng et al., 1993; Dixit & Biswas, 1969; Pavez & Peres, 1994, 1993). Several investigations have reported maximum floatability of monazite occurring at pH values between 8 and 9 (Cheng et al., 1993; Dixit & Biswas, 1969). A study conducted by Pavez and Peres (1994) compared the use of hydroxamate and sodium oleate for the treatment of a monazite ore and found that hydroxamate significantly improved the grade of rougher concentrate."

Jan 1, 2016