Search Documents

By V. Schenk

Dust exposure resulting from the exploitation and winning of natural resources below ground has presented a serious health problem since the beginning of mining. The boom phase of the German hard coal mining industry after World War II with at times up to 500,000 employees saw an increase of dust exposure of miners below ground as the mechanization of road heading and mining increased significantly. More and more miners were diagnosed with coal-workers-pneumoconiosis (CWP), a chronic and irreversible lung disease resulting in a significant impairment of pulmonary function. This realization led to a reduction of CWP in the German hard coal mining industry in the 1960s. The successful fight against CWP began with the introduction of technical dust prevention measures. By infusing the coal seam with water before mining, sprinkling and spraying of heading and mining machines as well as canopies with water, aspiration in places with high amounts of dust and the suppression of dust with chemical substances it is possible to significantly reduce the miners? dust exposure. All operating points below ground are checked and measured regularly with regard to dust exposure. Through the combination of these values together with the individual shift data a relatively precise profile of individual dust exposure can be obtained. This profile allows the targeted work assignment when certain predetermined limits have been reached, moving the miner to a work place with less dust exposure and thus reducing the chronic dust exposure. The state of health of the individual is known because since about 60 years ago extensive occupational health checks have been carried out regularly at least every two years which means that work restrictions can be imposed depending on the findings. Since the beginning of the 1980s more value has been attached to not only situational but also behavioral prevention. Given the comprehensive provision of protective masks, having a protective effect as well as the required comfort when being worn, each miner has the opportunity to protect his respiratory organs depending on the specific dust exposure. Through a combination of all these measures the German hard coal mining industry has succeeded in beating the classic coal miner?s disease CWP. For mines in the Ruhr valley this means that a miner who started work after 1978 will no longer develop CWP.

Aug 1, 2013

By Karen M. Moffitt

Developments in mining methods and rates have led to an increase in the frequency and size of waste dump failures that have not been adequately predicted or explained in terms of conventional slope stability analysis. Monitoring data and visual observations suggest a unique mode of failure responsible for large runout events. A numerical model has been developed to capture commonly observed patterns of deformation, and investigate the formation of the ensuing failure mechanism. The analyses have yielded a good correlation with observed field behaviour and have provided significant insight into the coincident stresses and deformations within the dump. Results indicate that while creep effects in the waste dump could have a significant effect on the magnitudes of displacement, the overall dump stability is governed by the strength of the foundation soils underlying the toe region. Consideration of both the stress and velocity fields leads to factors of safety for various dump heights and foundation slopes that are considerably less than predicted from limit equilibrium analysis. The results suggest that conventional limit equilibrium analysis techniques may not be adequate when assessing the stability and design of waste dumps on steeply sloping terrain.

May 1, 2001

By J. Lebl, S. Bharti, D. J. Cornett

"This paper presents the design and application of blasthole mining to an area at Strathcona Mine previously employing post pillar cut-and-fill. Extensive mining in the area had led to gradually deteriorating ground conditions and post pillar stoping was no longer considered acceptable. Alternative methods had to be investigated.Conventional methods for mining in poor ground were rejected because of the high cost. Blasthole mining was selected because iI offered good productivity and safety with acceptable costs. The design of this approach involved field investigations and the use of numerical modelling to simulate the different blasthole options and their impact on ground stability. The blasthole design incorporated reinforcement with cablebolts, use of a radio-controlled remote LHD unit, large-diameter holes, blast design and wall control. Potentially unstable areas were outlined during mining with ground monitoring instruments and the results used to modify mining plans during the production phase.IntroductionIn underground metal mines there is a need to improve safety and productivity and lower mining costs in order to maintain reasonable rates of return on investment. This requires the application of good engineering design to both mine planning and ground control in order to optimize production and costs and to forecast potential problems during mining. The task becomes more important when extensive mining leads to gradually deteriorating ground conditions, making existing mining methods and techniques no longer acceptable from a safety point of view. Alternative mining methods must, however, be sufficiently productive to ensure profitability. This paper presents an example of the engineering design and operating approach used by Falconbridge in dealing with such a situation at Strathcona Mine."

Jan 1, 1983

By A. I. A. Salama, M. W. Mikhail, R. J. Mikula

"The Coal Research Laboratory (CRL) of CANMET along with other research organizations in coal-producing countries envisage major benefits from computer applications in coal preparation, Some of these benefits are greater system flexibility, improved coal preparation plant performance efficiency and efficient utilization of manpower, all of which result in economic benefits. Computers can be applied for both on-line and off-line purposes; this paper focuses on the on-line applications from the process control point of view.A critical discussion of the different analog and digital process control systems is presented. Recent developments in Great Britain, West Germany, Poland and Australia on automation and instrumentation using on-line measurements of coal ash and moisture contents are identified.The CRL research and development strategy aimed at achieving on-line computer control of an automated coal preparation plant is presented.IntroductionIn the past twenty years an enormous progress in the area of computer technology has been noticed. Computer applications in industrial processes offer greater system flexibility, improved plant performance efficiency and efficient utilization of manpower. Significant computer control development in mineral processing has already been achieved. Although progress has been made in the area of computer applications in coal preparation, more effort is needed to utilize the full potential.The computer applications in coal preparation can be viewed as off-line and on-line. Considerable progress has been reported in the area of off-line computer applications, especially in the areas of modelling, performance evaluation/prediction and statistical analysis. However, only modest progress in on-line applications has been reported(1-7). This paper will focus on: online instrumentation and process control applications, different analog and/or digital control systems, on-line automation and instrumentation in other countries and CRL strategy toward pilot plant automation."

Jan 1, 1985

By Ali Roshanfekr

Linear mine-waste dumps at open-pit mine sites essentially represent expedient places to deposit large quantities of waste rock. Being in valleys in most cases, the effect of the water flowing through and out of the deposit often raises questions about their hydraulic behaviour and geotechnical stability, especially the zone of the downstream toe. In order to provide better tools to assess the behaviour of these dumps a laboratory and analytical study was conducted. Firstly, physical models were built to assess the flow capacity and hydraulics associated with the linear growth of such dumps. It was found that the elevation of the point of first-emergence on the downstream side becomes constant after the dump grows to a certain length, but that the upstream depth concurrently increases. The limits of applicability of the theories of Hansen et al. (1995, 2005) are discussed in this regard. Secondly, in analysing the seepageface downstream, two approaches for solving this spatially varied flow (SVF) problem were undertaken. Under one of the approaches links to SVF depths were merely made to the hydraulic heads of the body (interior) and flux was calculated using conventional surficial nodes after the fact, Under the other approach flux nodes were used to link the SVF algorithm to the hydraulic heads further ?inside? the body of the rockfill. Although there are inherent uncertainties, it was found that these two methods can be made to perform equally well. Research continues but it appears that a linear variation in depth can be assumed without inducing any unrealistic exit gradients in the zone of primary concern with respect to unravelling.

May 1, 2011

By J. B. Evans

"NORMALLY the duties of the exploration engineer and geologist cover the initial, and possibly, the most important phase of mining property evaluation; that phase being the presentation of an opinion of the property's ore reserve potential in terms of tonnage and grade. The prime objective of this pa-per is to outline one method of bridging the wide gap that lies between a know ledge of a property' s tonnage and grade potential and an appreciation of the value of that property in dollars and cents.THE PRESENTATION OF PROPERTY EVALUATIONThe engineer engaged on a mining property evaluation, regardless of whether he be an independent consultant, or a company employee, has as his goal, the presentation of his appreciation of the property's potential value or worth within terms of reference acceptable to his principal.To furnish a complete evaluation report, the evaluator must firstly study all aspects pertaining to the particular property under consideration, then present his appreciation of the property's worth in some tangible form. The ultimate presentation is one giving a Present Value of the pro pert y in terms of monetary exchange. Such an idealistic presentation is not always possible; typical preventives being -insufficient reliable information, limited time, Jack of ability and absence of definite direction."

Jan 1, 1960

By D. C. Van Aken, O. J. Rajtora

A research effort sponsored by the Department of Energy (DOE) and several steel producers, is investigating the benefits of coating steelcasting nozzles with various materials. Coatings were applied to casting simulation nozzles made from industrial tundish nozzles (primarily of magnesia) and industrial submerged entry nozzles (SEN's) (primarily of alumina-graphite) in order to extend casting time prior to nozzle clogging. Nozzles were coated by air plasma spray (APS) using a 9M series APS system from Sulzer-Metco. The ability of these coatings to provide protection from clogging was evaluated using a steel casting simulation. Substrate-coating compatibility was characterized using optical and SEM microscopy.

Jan 1, 2004

By Andrew L. Mular, Robert P. Edwards

"The operation of flotation circuits is often regarded as a combination of art and science. Expert systems offer a method by which the art may be captured and supervisory control of flotation circuits fully realized. Operating knowledge, the art, can be consistently employed to enhance regulatory control through the judicious application of an expert system. Using an expert system, a supervisory control routine was developed, and success- fully implemented, in the copper flotation circuit at Brenda Mines Ltd.The expert system ran in conjunction with regulatory PI controllers on a personal computer. The expert system received assays via an on-stream analyzer and adjusted regulatory loop set points as required in real-time. From its commissioning in November, 1989, to the end of the mine 's operation in June, 1990, it was enthusiastically embraced by the operators and attained operating levels superior to those achievable manually.IntroductionExpert system (ES) software springs from research into artificial intelligence and is currently making significant inroads into business and industry. ES proponents make many attractive claims; they are a means of capturing the knowledge of experts and they can be programmed by non-programmers. To date, most uses of this software in the process industry are in off-line applications, meaning that the applications are not tied directly to operating (on-line) environments. Moreover, in on-line environments, they are typically employed as advisors and only suggest changes. Human operators are required to close-the-loop to the process. Yet, an ES should be applicable to operating environments and, if the claims of the proponents are valid, should also be better than existing tools. As an intelligent controller an ES must use the knowledge of experienced operators, apply it directly to a process and do this without the intervention of human operators. On-line applications have been successfully employed in the closed loop control of SAG circuits (Herbst et al., 1989) and flotation circuits (Hales, 1989). Harris and Kosick (1988)detail an implementation for flotation control at the Polaris Mine."

Jan 1, 1992

By A. S. Robb

SAMPLING of an ore-body is one of the fundamentals in its exploration, development, and exploitation. It is carried out to determine the gold value per ton of an ore-shoot and the probable gold output of the refinery. Sampling also places any broken ground in one of two classes, ore or waste. The value and importance of correct sampling has been shown repeatedly in the past. On the other hand, instances could be given where those in charge of mines have not believed in sampling, and the result has been the same in every case-disaster. This has in all probability been due to assuming that good-looking, well-mineralized rock was ore. Sampling in some form might have averted this misfortune. In this essay, only the method of sampling and the estimation of ore reserves is treated. All titles, figures, and values are fictitious. None of the illustrations can be directly applied to any portion of the Hollinger mine, except Figures 1 and 2, which are included with the special permission of the Canadian Mining Journal. METHODS OF SAMPLING Hollinger Consolidated Gold Mines, Limited, has, from the very beginning of operations, carried out an extensive system of sampling, and the results of this sampling have completely governed the whole mining programme. The Hollinger discovery was made in 1909 and prospecting and exploration of 'the surface began at once. Four men were given jobs as samplers and they sampled thoroughly all the outcrops and all bed-rock which could be exposed to view by removing the overburden. When shaft sinking began, samples were taken at two-foot intervals. In 1912, an underground gang of six samplers was organized, and the number was increased at a rate of about two men per year as the size and extent of the workings grew. No permanent record of sampling was kept until 1919, in which year an average of 11.6 men took 28,458 samples, cutting 113,894 feet of sample. From that time until the end of 1934, the average number of samplers varied, but the total number of samples cut, and the total footage sampled, increased.

Jan 1, 1937

By A. Tohn, K. Adham, R. Lu, D. Lemieux

"To remove sulphur, carbon and arsenic from the gold concentrates of Dundee Sustainable Technologies (DST), Hatch has designed a demonstration plant roaster using the fluid bed technology. The fluid bed was selected for its ability to maintain stable temperatures and uniform reaction conditions. Data points from a small pilot plant (operated by DST) were used for setting the parameters of the demo plant roaster.The DST demonstration plant is being built to further prove their patented gold extraction process at an industrial scale. Their gold extraction process is based on halogenation at atmospheric pressure and relatively low temperatures. Before the halogen leaching, most of the sulphur, carbon and arsenic should be roasted out of the feed concentrate.The Hatch fluid bed roaster design includes a moist feed introduction system, simple bed cooling for temperature control, and cyclone fines recirculation. The demonstration plant roaster is planned for construction in 2014, and the performance results will be presented in a future paper."

Jan 1, 2014

By Kwang-Hyun Jeon

Recently, 3D printing technology in the manufacturing field is in the spotlight. In the construction industry, similar rapid prototyping technology that does not use conventional form can be applied to meet the demand on free formed structure that can provide aesthetic value and functionality. Conventional formwork can increase construction cost and period for various structure with complex shapes while it has numerous advantages such as high strength, convenience, accuracy and good quality of surface roughness. To meet the demand on free formed structure, automated freeform construction systems such as Contour Crafting and Concrete Printing have been developed with active collaboration between university and industry in USA and England. However, details on the system have not been fully released in public, so the possibility of its fusion and spin-off technology cannot be expected. In this paper, cost-effective solution for mechanical and control system for constructing a free curved structure without mold are described. As an appropriate material for the system, fiber reinforced mortar was selected by experiments on compressive strength, setting time and fluidity. After performing G-code simulation, transfer and extrusion experiments with the selected mortar mix were performed and the possibility of the development of automated freeform construction system was demonstrated. Based on this research results, it is required to keep the automated freeform construction system improve and extend it into the new application area in construction industry.

Aug 1, 2013

By J. W. Smith, J. Van Dusen, A. Papachristodoulou

"As part of a study to evaluate factors affecting tankroom air quality, the mechanism of aerosol generation from bursting bubbles in electrowinning operations has been investigated. Typically 2 to 3 mg/m2.s are produced in zinc tankrooms. Analysis shows that the rate of production of film drops (geometric mean diameter - 2 urn] increases with decreasing bubble size, and that jet droplets (geometric mean diameter - 20 um) are not produced with gas bubble larger than - 4 mm. Both mechanisms of drop formation and current efficiency are affected by surface active agents, with an over-all reduction in emission of up to 60% to 70% being achievable. A source control system which does not adversely affect electrolyte properties is always preferred, and coalescence of all gas bubbles in to a continuous stream of gas at a single point on the electrolyte surface would eliminate aerosol emissions. This objective was the basis for design of a coalescence device which, in laboratory tests, reduced the emission rate by over 95%.The control device fit s over the electrodes in the electrowinning cell and is partially immersed in the electrolyte. A number of changes in the design which resulted in significant improvement in the performance of the device are reported.Field tests have shown that only about 75% of the aerosol below 10 um can be eliminated by coalescence. The remainder (up to 95% of the total) is controlled by coalescence of droplets, by impaction on the exposed collector surface and gravitational settling.The device does not interfere with operation of the tankroom, handles the effect of surges in power during harvesting, and is simple and inexpensive to maintain. IntroductionDuring the electrowinning of metals (such as zinc and copper) gases are evolved along the electrode surface forming small bubbles. The bubbles travel upwards and burst on the electrolyte free surface generating, in this way, small droplets. Because the electrolyte is often highly acidic or contains toxic materials, the whole process can result in the formation of an aerosol in the atmosphere above the electrowinning cells which poses a serious health hazard to workers in the area, and corrodes equipment."

Jan 1, 1988

By M. M. Papic, G. M. Kimber

"Hat Creek coal was treated by the liquid solvent extraction process in a continuous plant at the U.K. National Coal Board Coal Research Establishment.Extraction levels of over 80 per cent dry-mineral-matter-free (dmmf) coal were achieved.Total light oil yield was around 47 per cent of the dmmf coal. The light oil was shown to be a good feedstock for secondary refining into gasoline, jet fuel and diesel fuel.In spite of the high mineral matter content of the coal the solid residue was successfully removed from the coal extract by filtration.IntroductionBritish Columbia Hydro (BCH) and the National Coal Board of Great Britain (NCB) undertook a joint project to test the Hat Creek coal from British Columbia in the NCB's coal liquefaction process designed to produce transport fuels and feedstocks for the chemical industry by the liquid solvent extraction of coal(1), In this process most of the coal is dissolved in an aromatic solvent and the residual solids consisting of mineral matter and undissolved coal are removed by filtration. The resultant coal extract solution is fed to a hydrocracker for conversion to light liquid products and a fraction suitable for recycling as solvent. The light liquid products can be converted to gasoline and diesel fuel in a secondary refining stage.The dissolution of the coal is effected by heat-treating a slurry at a temperature in the region of 400°C which causes some bonds in the coal to rupture with the formation of radicals(2,3). These radicals are stabilized by hydrogen transfer from the hydroaromatic groups in the solvent, resulting in a reduction in the molecular weight of the coal. In the absence of donor groups the radicals combine to form an insoluble high molecular weight product(4). From studies of the kinetics of these reactions it has been shown that the formation and stabilization of the radicals is rapid at temperatures around 400°C(2,3). The dissolution of the depolymerizing coal is, however, relatively slow and the need to ensure complete dissolution in order to achieve a high extraction restricts the selection of digestion time(5). Further, it is important that digests do not contain depolymerizing coal as it may re-form under the applied stress in the filter cake inhibiting flow through the bed and resulting in low filtration rates(6).Thus, in practice relatively long digestion times are generally required in order to ensure complete dissolution of the depolymerizing coal, while it is also important to avoid depletion of the hydrogen donor groups in the solvent which would lower the rate of hydrogen donation to the coal and thus reduce the extraction yield and adversely affect the filtration(7). Clearly it is desirable to optimize the digestion time and temperature with regard to the extraction yield and filtration properties.The precise control of the distribution of products from the hydro-cracker is important for the composition of the recycle process solvent. The principal functions of the solvent are to provide a source of donatable hydrogen and a vehicle for the dissolution of the depolymerizing coal. Hydrogen transfer from the solvent, achieved by the conversion of hydroaromatic to aromatic groups, stabilizes the radicals formed by thermal cleavage of some of the bonds in the coal resulting in a progressive reduction in the size of the coal molecules(8,9) and dissolution in the solvent. The combination of radicals would result in the formation of insoluble material and a reduced extraction yield of the coal(4). Thus to achieve a high extraction yield the solvent should contain sufficient hydrogen donor groups to prevent extensive radical combination. The composition of the solvent should also be controlled to allow dissolution of the depolymerizing coal and to prevent precipitation of this material during the subsequent processing of the coal digest and extract solution. The formation of a precipitate not only reduces the extraction yield of the coal and adve"

Jan 1, 1985

By G. Q. Liu

"The application of oxygen-enriched cyanidation to three Canadian gold ore samples has been investigated. The results showed that the use of oxygen can improve gold dissolution kinetics, reduce grinding time, and lower cyanide and lime consumptions. To obtain the same gold extraction, the required cyanide leaching time was reduced from 48 hours in slurry containing 8 ppm O2 to 12 - 24 hours in 20 ppm O2 slurry. Reagent consumptions were reduced by 23 - 37% for cyanide and by 35 - 54% for lime. There was little advantage to further increasing the dissolved oxygen to 32 ppm from 20 ppm. Gold extraction from the +200 mesh fraction improved 4 - 14% in oxygen-enriched slurry. A general kinetic model derived from the cyanidation of three ore samples can be described by the following equation: <equation>where E is the gold extraction (%) at time t (hours), EI is the ultimate gold extraction (%) , and &apos;P and k are constants depending on cyanide concentration, level of dissolved oxygen, and the characteristics of the ore samples. Comparative studies of conventional carbon adsorption and carbon adsorption in oxygen-enriched slurry have also demonstrated that oxygen enrichment resulted in more favourable conditions for gold adsorption."

Jan 1, 1995

By E. Y. Carlson

"IN A SHORT PAPER it is impossible to do much more than to list the industrial minerals found in Saskatchewan and to give a brief description of the activity associated with each. I will not attempt to discuss the geology. It is sufficient to say that the settled part of the Province is covered by glacial drift which varies in thickness from a few feet to several hundreds of feet, and that this has hindered the search over much of the Province.CLAYA notable exception to this is the Cypress Hills area in the southwest corner which did not suffer any glacial action and where we find some of the large exposures of Cretaceous clays. In this area, the majority of the deposits are of stone-ware clays which are •an excellent raw material for such products as face brick and sewer pipe. Although the clay cannot be transported over any great distance it is used extensively in Alberta and Saskatchewan in the production of these products."

Jan 1, 1959

By F. Andrieux

"Extruded aluminum profiles are increasingly used for lightweight vehicle construction. Since fracture strains of aluminum profiles are relatively low, damage modeling is crucial for reliable crash simulation. For aluminum profiles, not only the stress state but also the orientation influenced both the deformation and damage behavior. For the material characterization smooth tensile tests were performed in six orientations, both stress-strain curves and r-values were registered. Moreover notched tensile and shear-tension tests were performed in three directions. Finally punch specimens were tested to investigate biaxial loading. Digital image correlation (DIC) analyses were performed to determine local strain values such as critical values at failure. Numerical investigations were conducted with the strain based damage model GISSMO, which is well suited and widely applied for crash simulation. For a strain based failure model the choice of the deformation model is crucial. Deformation models with increasing complexity were investigated to find the best compromise over all experiments. It was found that there is still a great requirement on development of a material model which describes the orientation dependence of the hardening behavior over all stress states in order to be able to use a strain based failure model reliably.INTRODUCTION Weight reduction is an important step for less energy consumption and as a consequence aluminium is increasingly used in automotive parts. An important field of application is the well-established aluminium extrusion which allows the realisation of quite complex shapes of profiles required for an innovative lightweight design with integrated functions. Typical applications are chassis parts, bumpers, crash elements, air bags, etc. Especially the Al–Mg–Si medium strength alloys of the 6000 series can be easily extruded to form complex profiles and prevail for extrusion. Since fracture strains of aluminum profiles are relatively low, damage modeling is crucial for reliable crash simulation. For aluminum profiles not only the influence of the stress state but also the orientation with respect to the extrusion direction have an influence on both the deformation and damage behavior and need to be characterized. The effect of orientation on deformation behavior has been intensively investigated in the last decades and material models haves been proposed (e.g. Barlat & Lian, 1989; Barlat, Lege, & Brem, 1991; Barlat et al., 2003) to describe accurately anisotropic behavior. However it can be noticed that the parameters of anisotropic material models often rely on the yield stress in different directions, which means that the effect of strain hardening is not automatically accounted for. The accuracy of the models at large deformation is not guaranteed and has to be verified. In contrast to deformation models both the characterisation and the modeling of anisotropic damage behavior are not systematically studied. Isotropic failure models based on a critical strain as function of stress triaxiality (ratio of the hydrostatic stress to von Mises equivalent stress) are widely used for crash application (e.g., Bai & Wierzbicki, 2010; Sun, Andrieux & Feucht, 2009; Sun et al., 2013). The mechanisms of failure are manifold and not fully understood; to develop an anisotropic failure model it is mandatory to also have experimental data in different orientations for loading scenarios other than uniaxial tension, e. g. shear, biaxial tension, which implies an extensive experiment plan. This makes the development of failure models more challenging than deformation models for which it is possible to develop a reasonable anisotropic model using the framework of yield function and calibrate the material parameters based on results of tensile tests in different directions. Moreover the development of deformation and failure models are intricate as the variables governing the damage evolution are predicted by the def"

Jan 1, 2018

By Russell Spry

THE cyanide plant of the Cariboo Gold Quartz Mining Company, Limited, at Wells, B.C:, in the Barkerville section of the Cariboo mining division, was erected during the latter part of 1932 and placed in operation in January, 1933. The initial capacity of the plant was about 50 tons daily. This was increased to 100 tons at the end of 1934 and stepped-up to 150 tons in September, 1935. It is expected that further plant extensions, for milling a total of 200 tons daily, will be required during the early part of 1936. Recent additions to the mill have been so planned as to permit ready expansion to 275 tons daily when underground development warrants the milling of this tonnage. It is the purpose of this paper to outline briefly the steps taken to bring the plant to its present capacity and to comment on possibilities for further plant expansion. The gold in Cariboo Gold Quartz ore occurs as free gold in the quartz and on pyrite surfaces. Some of it is very finely divided, specks l/10,000 inch having been observed microscopically, according to Dr. G. Hanson. In addition to pyrite, which comprises probably 15 to 20 per cent of the mill feed, galena and sphalerite are present, with small amounts of arseno-pyrite and chalcopyrite. Sulphobismuthites-chiviatite, galenobismutite, cosalite, etc.-occur more or less frequently in certain sections of the mine. Following tests on Cariboo ore by the Mines Branch, Department of Mines, at Ottawa, treatment of the ore by straigh t cyanidation was recommended and a 50-ton plant employing continuous counter-current decantation was erected. This plant was built as a pilot mill, the intention being to erect a larger mill after metallurgical treatment had proved successful over an extended period. This original installation, however, has been enlarged and retained as an operating unit, additional equipment being added to it as capacity increases have been required.

Jan 1, 1936

By Lee Nichols

The Oil Sand Industry in northern Alberta, Canada, disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called Consolidated Tailings or Composite Tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities. Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are long-term stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface. The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process.

May 1, 2004

By L Gill

The four basic types of electric motors -squirrel-cage, wound rotor, synchronous and D.C. -are de-scribed, with particular reference to speed-torque characteristics. The three classifications of squirrel-cage motors, C.E.M.A. B, C and D, are compared, and methods of selection for specific drives are outlined. Wound rotor and synchronous motors are covered from the viewpoint of construction details, methods of operation and control required. The application of these motors to crushers, conveyors and ball mills is described and reasons for their selection are given. The application of D.C. motors to haulage equipment and mine hoist drives is included, and the basic principles of a variable voltage drive are illustrated. Efforts have been made through-out to provide specific examples of motor selection, with particular reference to the mining industry. THIS paper will attempt to answer the question -"which motor should be used for a specific drive?" Although it is impossible to cover the complete subject of electric motor application here, we hope to give some idea of the types of motors available and why certain types are used on specific applications.

Jan 1, 1963

By M. Sider, D. L. Piron

"The cost of energy is a growing factor in the cost of zinc production. Electrowinning from sulphate solutions with periodical reverse current or from acidic chloride or alkaline solutions could be the way to lower costs. A comparison of the energy consumption for electrolysis shows that the alkaline solution may be considered the most promising alternative. IntroductionZinc electrowinning from sulphate solutions is a very energy intensive process (typical specific energy usage : around 3.1 kWh / kg zinc). This energy consumption represents 35% of the total cost of electrolysis and is the most important cost component.In order to lower costs, the energy efficiency of the sulphate process should be improved or alternative processes should be developed. In this laboratory, that objective has resulted in research on electro winning in sulphate solutions with the use of periodical reverse current (PRC) and in acidic chloride and alkaline solutions.Some of the results obtained in this laboratory and already published and new experimental results reported in this paper make it possible to present a more critical comparison of the energy consumption of the three processes mentioned.ExperimentalThe experiments at constant current were carried out as described previously. Specific conditions are indicated in Table I. Current efficiencies were obtained by weighing deposits.ResultsThe best energy consumptions for electrolysis obtained in this laboratory for the three media are presented in Table I. More detailed results can be found in the papers already mentioned."

Jan 1, 1988