Search Documents

By K. Sawamukai, S. Ogasawara, D. Umenai, T. Tsuruta

"Removal of cobalt, strontium or cesium ion from the aqueous solution containing each metal ion only using microorganism was examined. Arthrobacter nicotianae which had a high ability to remove cationic metal ion was used for the removal of each metal. The removal of cobalt, strontium or cesium using A. nicotianae cells was affected by the solution pH, concentration of metal ion, and cell amount. The effects of above mentioned factors on the removal of each metal and time course of strontium from the solution containing each metal only using A. nicotianae cells were reported in this paper. INTRODUCTIONRadioactive elements, such as cesium, iodine, strontium, plutonium, barium, cobalt, lanthanum, yttrium, and tellurium, were detected around Fukushima Daiichi nuclear power plant, which was damaged by the magnitude 9.0 earthquake and the tsunami followed.The removal of radioactive elements from contaminated sources is a worthwhile subject to investigatein terms of environmental control. Research efforts have been especially concentrated on studying microorganisms that remove uranium including bacteria (Andres et al, 1993, Hu et al, 1996, Marques et al, 1991, Strandberg et al, 1981), actinomycetes (Byerley et al, 1987, Friiss and Myers-Keith, 1986, Golab et al, 1991), fungi (Byerley et al, 1987, Galun et al, 1983a, Galun et al, 1983b,Tsezos and Volesky, 1981, White and Gadds, 1990) and yeasts (Strandberg et al, 1981, Schmate II et al, 1978).We have investigated removal and recovery of uranium from aqueous systems using microorganisms isolated from uranium mines. We identified some strains of bacteria with extremely high uranium removing abilities (Sakaguchi et al, 1996), and thus, the microbial biomass may be considered as an adsorbing agent for the removal and recovery of uranium and heavy metals present in aqueous systems around Fukushima Daiichi nuclear power plant.In the present study, we screened various species and strains of bacteria, actinomycetes, fungi, and yeasts for their ability to adsorb uranium (Tsuruta, 2002). Basic features affecting uranium adsorption?co-existing cations and anions, cell amounts, pH, and the adsorption time course?by Arthrobacter nicotianae cells, which adsorbed the largest amount of uranium, were also investigated. In addition, we examined the removal of an other actinoid element, thorium ion, which may be present with uranium in refining effluents.In this paper, the removal of cobalt, strontium, or cesium from the solution containing each metal ion using A. nicotianae cells is discussed."

Jan 1, 2012

By D. L. Johnston

"Function and ApplicationsWater-only cyclones, (WOC) are a dynamic mineral separator which cause minerals to separate in a water medium by virtue of difference in specific gravity. Figure 1 shows diagramatic plan and sectional views of a water-only cyclone.A slurry of mineral matter and water is fed through the inlet opening under gravitational or pump pressure. The combined effect of centrifugal action and conical shape is to concentrate the heaviest fraction of mineral on the periphery and bottom of the cyclone. This layer of higher specific gravity particles increases in thickness and density between the cyclone inlet and apex. The action in the bed of higher gravity particles formed in the flattened portion of the cone surrounding the tip of the vortex finder deter;nines the specific gravity of separation or cut-point. Mineral particles of lower specific gravity flow with the bulk of the water, out the vortex finder. Mineral particles of higher specific gravity flow with little water out the apex. A more technically e:mct description of the functioning of the water-only cyclone can be found in previous publications noted in the references.The water-only cyclone was invented and refined by J. Vis man, formerly of the Canadian Mines Branch staff, between 1958 and 1965. The first industrial application noted in the literature was when it was introduced as a cleaner for fine coal in 1962. Since 1970 the water-only cyclone has become a common separation apparatus in many Canadian and foreign coal processing plants. The only other mineral industry application known to the author is in separation of gold bearing heavy minerals from sand<'>. The potential does exist for other applications and this area deserves to be investigated more thoroughly than it has been."

Jan 1, 1989

By B. W. Brooks

"After an extensive period of University research and field trials, large scale reclamation of the Waite Amulet tailings discharge areas commenced in the spring of 1978. The Noranda program consists principally of sampling the complete dam to determine the vegetation potential of the various areas, addition of the required amelioration materials, and the use of good agricultural practices. This paper describes the development work that led to the establishment of the Noranda-Guelph Contract and the subsequent findings concerning the revegetation of tailings dams. Current revegetation procedures are presented. INTRODUCTIONThe Amulet Mine Ltd. was staked in 1924 and by 1930 had constructed a small 300 ton per day flotation plant. During the late twenties and early thirties, Noranda Mines Ltd. increased its equity in the company to gain a sixty percent share of this small mine. In 1933 the mine was amalgamated with another small producer, the Waite Ackerman Montgomery Mine Ltd., which was more than eighty per cent controlled by Noranda to form the Waite Amulet Mines Ltd.An interesting historical side point to the story of the Waite Ackerman Montgomery property is that a concentrator was never constructed. In fact, the first ore to go through the Horne mill of Noranda Mines Ltd., built in 1928, was not from the famous upper H and L ore bodies but custom shipments from the Waite."

Jan 1, 1981

By G. R. Davidge

"Falconbridge Mine has a history of significant microseismic activity dating back to 1955. Since mid-1981, a microseismic monitoring system has been operating in the area around the No .9 Shaft hoist room located 25 m from the are zone at a depth of 1200m. Several mine wide faults dissect this area and have been shown to be microseismic-active due to mining. The microseismic monitor has been interfaced with a small dedicated personal computer and a communications device to perform routine data evaluation and to produce graphical output. The programs are described and selected result s from the monitoring program are presented.IntroductionFalconbridge Mine is located on the southeast rim of the Sudbury Basin. The nickel-copper sulphide ore zone is essentially a tabular orebody striking approximately east-west and dipping at 80 degrees north near surface and rolling to 75 degrees to 80 degree s south by the 1000 level. (Mine level number s represent the approximate depth in feet below ground surface .) This dip is maintained down to the 6000 level. The north wall is comprised of jointed norite and a faulted contact up to 1 m thick exists between the ore zone and the norite. The south wall rock is a greenstone with highly siliceous lenses and often has a faulted contact with the ore zone. No less than five mine wide faults exist, as shown in Fig. I.Mining ha s been carried out from virtually the bedrock contact to depths of 1830 m although the majority of current activity is between 900 and 1500 m below surface. A winze provides access below the 4025 level and the cage hoist room is located on the 3850 level in the north wall 25 m from the contact. Because of concern for the stability of this hoist room, there has been no mining activity within 60 m of the hoist room and by 1980 this block of ore was one of the major blocks of high-grade ore remaining in the mine . Mining of this block was originally scheduled for very late in the decade.Prior to a six-month shutdown in 1982, this mine produced approximately 450,000 tonnes of ore annually, mainly by cut and- fill techniques. Following the shutdown, annual production has been reduced to approximately 200,000 tonnes and production is now mainly by undercut and fill techniques .Mining-induced seismicity has occurred at Falconbridge Mine since at least 1955 and reviews of the microseismic problems for the periods from 1965 - 1970 and from 1971 to 1979 were made by Singh (1971) and Vongpaisal et al. (1980), respectively. The need for instrumentation was addressed by these authors. Following several large events during the spring of 1980, a decision was made to investigate existing microseismic monitors and to apply micro seismic monitoring techniques in Falconbridge Mine. Application of microseismic monitoring to Falconbridge Mine was to concentrate on the No . 9 Shaft hoist room area of the mine, particularly around the 4025 level where a large mechanized cut-and- fill stope was approaching this level. By mid - 1981, the microseismic monitor was fully installed and with in a year , a short-period seismograph and a personal computer had been added to the system."

Jan 1, 1984

By Amin Saravari, Jamal Jafari, Abbas Sam

"The fourth concentrate production plant includes the comminution systems and the medium-low intensity magnetic separators (LIMS). Based on different conditions, two types of materials are fed into the plant. Type A: 70% of mine ore and 30% of reject materials from magnetite plant and type B: 100% of mine ore. The goal of the present study was to increase the iron grade and the blain number with low sulfur content in final concentrate as the pellet feed. An appropriate pellet feed should have more than 67% of iron, less than 0.1% of sulfur and a Blain number of more than 1800 cm2/g. The Fe, S and Blain no. amounts for the present concentrate are 66.6%, 0.95%, and 500 cm2/g (feed type:A) and 67.8%, 2.3%, and 450 cm2/g (feed type: B), respectively. In this research, the plant improvement efficiency was evaluated by changing the feed particle size distribution and using the flotation system. Laboratory experiments were designed based on the three circuits:1) LIMS (Low Intensity Grinding Rolls) feed grinding-LIMS test-flotation test2) LIMS feed grinding-flotation test-LIMS test3) LIMS concentrate grinding-flotation testThe best results were obtained using the first circuit at the LIMS feed size (d80) of 132 ?m. The processing results using the circuit no. 1 (feed type: A), showed a LIMS concentrate with 69.8% of Fe and 0.36% of sulfur. In this case, the final concentrate (after flotation) with Fe grade of 70.3%, sulfur content of 0.07% and Blain no. of 1571 cm2/g were obtained. In case of the feed type of B, the LIMS concentrate with Fe grade of 68.7%, and sulfur grade of 1.6% was achieved. Also, the Fe and sulfur contents were 69.3%, and 0.4% respectively with a Blain number of 1112 cm2/g. According to the obtained results, it was suggested that a LIMS feed comminution along with a LIMS and flotation systems are necessary to achieve an appropriate iron and sulfur grades with an acceptable blain number. To reach a concentrate Blain number as a pelletizing feed, a High Pressure Grinding Rolls (HPGR) system at the end of the processing line was recommended."

Jan 1, 2016

By G. Dörsam, M. Spreij, S. J. Van der Wal, A. P. Schmidt

The transfer of hot metal desulphurising from the torpedo cars to the hot metal ladles at the IJmuiden BOS plant no.2 caused a decrease in ladle lining life from 680 to 470 heats. Changing the desulphurising agent CaC2 for CaO during a trial period, for environmental reasons, led to a further decrease in refractory life. Availability of the ladles became critical and the major reasons for the low life were identified. Solving one of them, temperature, quickly resulted in restoration of the original lives. However, re- introduction of the new desulphurising agent on 50% of the heats again resulted in a decrease, this time from 700 to 550 heats. In order to be prepared for the full introduction of the new agent, thorough investigation of worn linings was conducted, revealing the major (chemical) wear mechanisms. With these findings, a new design for the hot metal ladle is proposed.

Jan 1, 2004

By J. B. Mawdsley

"The Red Lake Gold Shore mine is 4/5 mile west of the town of Red Lake, Ontario, and a mile northwest of the Howey mine. It came into production in August 1936, and in a little over 2 years produced 21,099.58 oz. gold from 83,949 tons milled.An investigation of this deposit was made by the writer during parts of September and October, 1937t. The geology of the deposit is also discussed by H. C. Horwood(2) , and the characteristics of the ore were investigated by the Bureau of Mines, Ottawa (1).The orebodies are pipe like and close together, in a north-northwesterly trending zone of dykes, veins, and shear zones in a granodiorite stock, just south of a pronounced valley with a trend of N.65°E. believed to lie along a strong shear zone and fault . The dykes, veins, and mineralization are believed to have been successively emplaced along structures having three general trends and that were due to compressive stresses that alternated, at least four times, from west of north to east of north. In common with many other gold deposits, the gold mineralization here occurred late and followed the last east-of-north stresses.WALL-ROCKSThe mine is within the Dome stock, % mile from its southeast margin. Near the mine the rock is a pink hornblende-biotite granodiorite, grading within short distances, but not abruptly, into a dark grey variety. Near the workings at least, scattered small inclusions form about ½ to 5 per cent of this body. Most of them are fine-grained, angular, or partly rounded, greenstone fragments, but some have been partly granitized and feldspar has been developed in them."

Jan 1, 1954

By A. R. MacPherson

"This paper considers four aspects of autogenous grinding. Part 1 discusses statements on power efficiency of autogenous grinding compared to conventional crushing and grinding systems. It also demonstrates how high-power efficiency can be obtained from autogenous grinding systems. Part 2 considers a simple method of testing ores to determine the type of autogenous plant which can treat these ores on a commercial basis. A comparison of testing for simple small plants vs large plants or complex ores is included. Part 3 considers important aspects which have to be considered in proper design of an autogenous grinding system. Part 4 discusses problem ores and how they can be treated in an autogenous system. INTRODUCTIONAfter about 35 years of using autogenous grinding plants in the mining industry, it is perhaps time to review where we are with this, by now, relatively old development. Autogenous grinding in this paper means grinding run-of-mine ore by fully autogenous means or by using a ball charge to assist the grinding (semi-autogenous). Also, autogenous grinding can be eitherby dry or wet.The use of autogenous grinding in the fifties was making its slow start, and it was not until the sixties that more of the mining industry would consider its use . By the seventies, most builders of new plants would have considered autogenous grinding, whether they used it or not, in the final design.In the eighties, most large plants use autogenous mills and to reduce over-all operating costs, many older conventional plants are now looking and actually retrofitting these old plants with autogenous grinding mills.It is evident that many misconceptions concerning autogenous grinding are still current. Some come from improperly designed plants which result from poor test work. There are many considerations in the proper design of autogenous plants. Some ores have been found to give problems even in a well designed plant. These ore types are beginning to be classified and recognition in the test stage allows steps to be taken in the design so that these ores can be efficiently handled in autogenous grinding plants.Therefore, this paper will address the following aspects of autogenous grinding:1. Misconceptions regarding autogenous grinding.2. Testing of ores to ensure a well designed commercial plant.3. Important considerations in mill design.4. Difficult ores, their recognition and types of design to handle such ores."

Jan 1, 1989

By Haofeng Xie, Lijun Peng, Xujun Mi, Xue Feng, Xiangqian Yin, Zhen Yang, Guojie Huang

The Cu/Al composite wires have been widely used in cable industry. Especially in the development of aerospace, the light weight character of wires is particularly important. The wires are fabricated by a drawing process and heat treatment. Mechanical and electrical properties are measured and analyzed. The bending behavior is studied by scanning electron microscope. INTRODUCTION Cu/Al composite is a typical bimetallic composite that has been used in plenty of fields such as automobile and aerospace. The composite has the advantages of excellent conductivity as well as low weight, which cannot be obtained from single copper or aluminum. Industrial products of Cu/Al composite include Cu/Al composite joints (Uscinowicz, R., 2013), Cu/Al bimetallic sheets (Li, X. et al., 2011), Cu/Al flat bar (Wu, Y. & Liu, X. & Xie, J., 2014) and CCA wires (Ahmed N., 1978). CCA wires refer to the composite wires that copper layer concentrically coated on the surface of aluminum core conductor, implementing solid combination of two metals on the interface and forming an integral. At present, the aircraft cable generally use copper or copper alloy conductor, which makes the wire in the aircraft occupy a considerable proportion due to the large density of copper. Therefore, the use of Cu/Al composite wires instead of copper wires for weight loss, is of great significance to the development of aerospace technology industry. Heat treatment is an indispensable procedure to improve plasticity during cold working process, which is of great importance to preparation of wires (Wang, Q. et al., 2008). During the heat treatment, the Intermetallic Compounds (IMCs) are inevitable formed at the contact area of Cu/Al due to the occurrence of diffusion (Lee, S. et al., 2012). According to the results of former researchers, kinds of IMCs were discovered. Antoine Gueydan (2014) identified the formation of three IMCs (Al2Cu, AlCu, and Al4Cu9) at the interface between copper and aluminum after thermal aging. IMCs have a significant effect to the properties of Cu/Al wires. Bending performance is a vital property for the actual application of wires. The brittle IMCs may create a stress concentration that can cause crack initiation during bending process. This work focus on the mechanical properties of Cu/Al composite wires after heat treatment. The effect of various annealing condition on mechanical and electrical properties are studied, in order to find the appropriate annealing conditions, which produce optimal combination properties of Cu/Al clad composite wires. Bending fracture of composite wires is discussed by morphology observation.

Jan 1, 2019

By J. A. Haskin

The Engineering Department at Flin Flon has the following responsibilities: 1. Underground Surveying. 2. Open-Pit Surveying and Supervision of Blasting. 3. Mine Geology and Examination of Prospects. 4. Design of Plant Additions and Improvements. 5. Miscellaneous Field W ork, Reports, etc. The entire surface plant, as well as the underground workings, are located by co-ordinates based on a triangulation system covering an area approximately one mile long by one-half mile wide. The origin of this system and one end of the base-line is the southwest corner of Township 67, Range 29, west of the Principal Meridian. The bearing of the base-line was determined from the township boundary, which runs true north, so that all other bearings are almost astronomical. This is a great convenience when our surveys must be tied to mineral claims, rights-of-way, and land subdivisions. As the base-line extends across Flin Flon lake, its measurement across smooth ice was simple and accurate. The length, slightly over 1,600 feet, has been adjusted for the temperature and tension of the standard tapes used and checked sufficiently to ensure a maximum error of 1 : 15,000. Each angle was repeated ten times, but as no special refinements were used, errors of as much as four or five seconds are possible. The elevation of the origin of the triangulation system was approximately 1,050 feet above sea level. The use of this true elevation in our surveys would have resulted in negative elevations underground as soon as the mine reached a depth greater than 1,050 feet. To avoid this complication we therefore added 4,000 feet to this elevation. The collar of the Main shaft, for example, which is actually 1,072 feet above sea level, appears in our records as at elevation 5,072. Underground surveying, which follows standard practice, is done by two mine surveyors who share three helpers. The meridian is taken underground from two wires hung in either of the two vertical shafts.

Jan 1, 1935

By O. -J. Siljan

"Refractory materials are an integral part of aluminium production. One special feature of aluminium making is the prominent role of sodium in all parts of the production process. This presence of sodium inflicts stresses on the refractory materials through reactions and may cause severe damages to the refractory linings. The present paper address possible reactions between sodium and refractories in anode bake furnaces, electrolytic pots and casting furnaces. The discussions presented in the paper points to the importance of selecting materials with excellent alkali resistance in all parts of the aluminium making process, although alkali resistance is not the sole parameter to determine refractory life-time. ""Acid"", i.e. silica-rich alumino-silicate refractories are shown to be the best materials for aluminium electrolysis cell potlinings, whereas high- alumina refractories based on minerals like andalusite seems to be the preferred choice for anode bake furnaces as well as cast house furnaces."

Jan 1, 2004

By J. Roth

"While not taking issue with the general thesis expressed in Dr. Ridge&apos;s analysis of the role of genetic concepts versus observational data in ore exploration (Ridge, 1983), the criticism could be offered that the author tends to slight the importance of conceptual (i.e. theoretical) models in mineral exploration.As a general rule, observational data in science lacks significance and utility without a theoretical construct to organize those observations. Theory in turn dictates what observations are made-and which ones are judged important. Thus, for example, prior to the elaboration-and acceptance- of the current model for volcanogenic base metal deposits, the structural aspect s of these deposits were most closely observed and studied by explorationists. The nature of the enclosing rocks and any attendant alteration was given minimal attention, and certainly didn&apos;t figure prominently as an exploration guide.Similarly, the importance of alteration features to exploration for porphyry copper-molybdenum deposits was only perceived when a theoretical model was developed to account for these aspects. Indeed, many of these porphyry copper deposits were regarded as epigenetic vein deposits by geologists of an earlier era observing and examining on a different physical scale-and with a different theoretical bias.In constructing and evaluating such conceptual models, explorationists primarily rely on observation data and proximate associations; speculative thoughts as to ultimate provenance or crustal evolution clearly play a subordinate role, as Dr. Ridge argues. This, however, should not obscure the fact that concepts and theories do indeed exert a major influence in mineral exploration."

Jan 1, 1983

By R. Saulters, M. Garshasb

The Transportable Moisture Limit (TML) is the copper concentrate moisture content beyond which liquefaction may occur during shipping. This study indicates that TML is a function of mineralogical characteristics of concentrate, which in turn may directly affect moisture retention properties. A comprehensive mineralogical and chemical analysis was conducted to determine the impact of composition and mineral content on concentrate’s TML. The analysis indicates that the high TML value is associated with particular minerals such as gypsum, swelling clay, muscovite and pyrite. Since higher TML values allow higher moisture contents for shipping, this property is desirable for concentrate inventory management and shipping flexibility. Scarcity of minerals that may increase TML contributes to limitations of shippable inventory. INTRODUCTION TML is the maximum moisture content of copper concentrate beyond which liquefaction may occur. Moisture content above the TML is considered a shipping hazard as it may result in loss of lives and cargo. The details of TML testing are given in ISO 12742:2007 (ISO 12742). In principle, TML is 90% of the Flow Moisture Point. The method of testing for Flow Moisture Point and TML is based on procedures that provide pulsations that simulate the cyclic force of ocean waves to determine moisture levels at which the onset of concentrate flow may occur. International Maritime Organization (IMO) provides guidelines for developing and approving TML testing and moisture determination in the context of its Moisture Management Plan (MMP) for shipment of copper concentrate cargoes (IMO 2013). The IMO regulations are specifically provided in MSC.1/Circ. 1454 “Guidelines for developing and approving procedures for sampling, testing and controlling the moisture content for solid bulk cargoes which may liquefy”. Since each port has its own operational characteristics, resource availability, peculiarities of governmental structure, and desired methods of interaction with the authorities, it is necessary to adopt the IMO guidelines to the local requirements. In order to establish a TML and MMP measurement system, it is required to implement and follow proper guidelines for the relevant procedures. For example, sampling procedures are developed in accordance of ISO 12743, “Copper, lead, zinc, and nickel concentrates – Sampling procedures for determination of metal and moisture content”. Moisture content of copper concentrate samples are determined in accordance with ISO 10251, “Copper, lead, zinc, and nickel concentrates – Determination of mass loss of bulk material on drying”. To assure strict adherence to the MMP procedures, the overall system needs to be integrated into the site QA/QC system, which would make them auditable and certified in accordance with standards such as ISO 9001, ISO 17025, and ISO 17020.

Jan 1, 2019

By Carricajo T., S. Nazari

This paper discusses a unique dynamic solution for optimizing comminution area in real time. The proposed technology is a combination of model predictive controller, optimization methods and real-time digital twin for mineral processing. For grinding area, the ultimate goal of an effective control strategy is to maximize the mineral processing, reduce energy consumption and stabilized size classification. To have a continuous and effective comminution operation, a reliable control system that minimizes the need for human intervention is necessary. The implemented advanced control strategy for comminution area consists of two layers in hierarchical structure. The lower layer objective is to stabilize the process stabilization using model based predictive controller (MPC) technique. The unique MPC used in this layer is called BrainWave™ chosen for its robustness, convergence and delay handling; furthermore, the developed platform offers stable and repeatable solution and has short implementation time. The upper layer is a supervisory control, which sends the preferred process operation points to the lower layer to drive the process towards optimal performance. The goal of this layer is to optimize the process targets, as well as making decision. To increase process performance, automatic ore characteristic adaptations are implemented in this layer. A digital twin of comminution area is built in the second layer that runs amongst the process in parallel. By communicating, the process data in real time, a virtual densitometer is built that is being used in our advance process control strategy. Our control strategy has been developed, tested and implemented in various areas of a copper concentration plant. The targets for implementing advance process control are usually increased throughput, decrease energy consumption and variability reduction in particle size distribution. Overall, the results showed in different mine sites are increase throughput between 2 and 5%, specific energy consumption reduction about 15% and process variability reduction up to 60%. In this paper we discuss the results of the recent implementation of this technology on Minera Los Pelambres, Minera Collahuasi and CAP Minería. Their concentrator plants have installed control systems with the most updates optimization features, for SAG mill, ball mills and thickeners.

Jan 1, 2019

By A. R. Kinkel JR.

"The Buffalo Ankerite mine is in the southern part of the Porcupine gold district of northern Ontario. The mine has a history of exploration and development reaching back to 1911, and has been operated continuously since 1932. From 1932 to 1942 a total of 510,874 oz. gold was produced from the mine. In 1941 the production was 71,654 oz. from 448,621 tons of ore.With few exceptions, the ore-bearing veins did not crop out. They were discovered during the prospecting of the prominent outcrops of barren or low-grade quartz-carbonate breccia near the veins.GEOLOGICAL SETTINGThe Porcupine gold district lies in an area of folded and sheared Precambrian lavas, sediments, and intrusives. The Buffalo Ankerite mine is in the southern part of a large fold. The structure appears to be a continuation of the Vipond cross anticline and accompanying syncline described in earlier papers (1, 2). The orebodies lie along both flanks of the synclinal part of the fold, and are known as the north and south vein systems, respectively. No mineable veins have been found on the axis of the syncline (Fig. 1).The rocks found in the mine area are pillow lava, dacite, conglomerate, quartz porphyry, tuff, and fragmental lava. The tuff and fragmental lava are now largely altered to chlorite schist. Productive veins have been found only in pillow lava, dacite, and conglomerate, but a minor amount of gold occurs in some of the quartz porphyry. The Porcupine Creek fault, a zone of intense shearing over 1,000 feet in width, lies immediately south of the mine. A spur fault branches to the northwest from the Porcupine Creek fault, separating the north from the south vein systems ( Fig. 1) ."

Jan 1, 1954

By N. E. Izatt

Molecular recognition technology (MRT) has a wide range of applications in the hydrometallurgical and chemical processing industries for the selective removal of iron as well as various other impurities from a variety of streams, including aqueous solutions through a wide pH range, as well as organic solutions. An example of a commercial application is provided for the removal of iron from an aluminum chlorohydrate stream. In this example, MRT has a selectivity for iron relative to aluminum which is significantly higher than that of ion exchange resins. A discussion of MRT capabilities for other impurities and streams is also provided.

Jan 1, 2006

By J. G. Stevens, S. W. Colley

"Selective separations of metals and ions in mineral extraction and refining are becoming more challenging as ore bodies become more complex and environmental pressures increase. The separation and containment of mercury produced in gold mining are a factor in the profitability and operability of mines. This paper will discuss the development and implementation of the Johnson Matthey HgFree selective mercury removal process. The process is designed to selectively recover co-leached mercury from either heap leach pregnant solutions at ambient temperature and low mercury concentrations, or electrowinning pregnant solutions at elevated temperature and high mercury concentration, without affecting gold or silver recovery. The process utilizes a highly selective adsorption-desorption step in which mercury is removed quantitatively by the HgFree adsorbent without adsorption of gold, silver or other metals present. Development of the original HgFree adsorbent has resulted in a process whereby mercury can be recovered as an inert salt and is never present as the free metal. The HgFree adsorbent can be regenerated and recycled in situ, and is capable of being reused multiple times. The overall process is compatible with existing gold mining and recovery practices and offers significant environmental and sustainability benefits, including reduction or elimination of the need to retort mercury with a subsequent reduction in potential mercury air emissions. Development of the HgFree adsorbent and process will be discussed along with a pilot operation at two operating mines.INTRODUCTIONMany gold ore bodies contain high concentrations of mercury which when extracted with cyanide, co-extract with the gold and other metals. This mercury is carried through the process with the gold, posing environmental and technical issues when it is separated from the doré. This paper describes a method to selectively adsorb mercury from the gold recovery circuit while it is in a soluble form, leaving gold to be processed as normal. The removal of mercury from the circuit eliminates the need for mercury retorting of doré and so reduces the potential environmental impact of fugitive emissions of elemental mercury."

Jan 1, 2016

By Laura Kelsey

Contaminant Robust In Situ Water Extractor CRIWE Nafion-based water clean-up Extract purified water from natural extraterrestrial sources In situ water processing for downstream electrolysis Chemically resistant to process contaminants such as acid

May 1, 2013

By Matthew A. Baumann

Tooth wear on mining shovels presents a challenge for productivity. A shovel with worn teeth suffers from increased digging forces, longer fill times, and an increased likelihood of lost or broken teeth and adapters. Efficient maintenance planning relies on knowledge of tooth decay rates and patterns. A fully automated wear monitoring system can record detailed logs of tooth wear, permitting G.E.T. personnel to optimize maintenance scheduling. Studies have demonstrated that planned tooth change-outs result in significantly reduced costs as compared to unplanned maintenance. A machine-vision-based tooth-wear monitoring method is introduced. A rugged camera is installed on the boom of cable shovels, or on the stick of hydraulic shovels. The images are processed using a photogrammetric algorithm to determine the individual tooth lengths. Tooth length data is collected at intervals during shovel operations, forming a profile of the current wear state, speed of decay, wear pattern, and expected lifespan of teeth. A case study in a South American mine on a Komatsu PC8000 hydraulic front shovel is presented. Tooth wear is tracked over a 6-day period and wear rate statistics are computed for 6 teeth. This validates the system and provides an example of how wear patterns can be recorded and analysed by an automatic system. Armed with this data, mine personnel can reduce the cost and lost time due to unplanned maintenance, and observe the effects of mine conditions and operator behaviour on tooth wear.

May 1, 2011

By Atsuki Sado, Akira Ueno, Kazuaki Takebayashi, Kunio Watanabe

The Saganoseki Refinery of Pan Pacific Copper Co., Ltd., Japan, introduced the ISA 2000® process in 2006 to improve product quality and productivity. After resolving various technical difficulties associated with the process, a current density of 325 A/m2 and electrolytic copper production of 234 000 tons per year were realized in 2018. In recent years, Saganoseki Smelter & Refinery has promoted treatment of recycled materials in addition to copper concentrates. Accordingly, the amount and type of impurities charged to the smelting process have tended to increase. In the electrorefining process, impurities such as nickel and antimony cause anodic passivation and formation of suspended solids, respectively. Although these undesirable phenomena can be avoided by controlling impurity concentrations in the anode and electrolyte to appropriate ranges, this also limits the choice of recycled materials that can be processed by the smelter. To achieve both stable operation of the electrorefining process and flexibility in treatment of recycled materials in the smelting process, Saganoseki Refinery improved the capacity of the impurity recovery processes during 2016 to 2018. This paper describes the expansion of the purification plant to remove and recover nickel and antimony. INTRODUCTION The Saganoseki Refinery of Pan Pacific Copper Co., Ltd., Japan, introduced the ISA 2000® (wax- less permanent cathode method) in 2006 to improve product quality and productivity. Since then, the refinery has gradually increased current density, and has been committed to establishing stable operation and high productivity via various improvements related to the electrolyte filtration and additive management systems. Figure 1 shows the trends of current density and current efficiency at the refinery. Although the current efficiency temporarily dropped when the current density was raised to 322 A/m2, it consistently exceeded 97% thereafter. At present, stable operation at 325 A/m2 has been achieved and continues.

Jan 1, 2019