Search Documents

By G. M. Proudfoot

IN June, 1940, a .Longyear 3420 blast-hole drill rig was purchased by the Hudson Bay Mining and Smelting Company for the purpose of experimental blast-hole drilling. The early work showed that the diamond drill could compete successfully with the Leyners then in use and by January 1st, 1941, the diamond drills were placed on contract. They may be considered to have gone into production at that date. Prior to the introduction of the diamond drill, our bench drilling was clone with Ingersoll-Rand S-70 and S-83 Leyner drills. Holes up to 40 feet were drilled, using coupled 1 1/4-inch round steel. Bits with a gauge of 3 inches were used in starting these holes, with a drop of 1/8-inch gauge for each 2-foot run. The holes normally ended with 1 1/2 or 1 5/8-inch gauge, though bits down to 1 1/8 inches were available for holes longer than normal or for holes drilled in abnormally abrasive ground. This method of drilling was very satisfactory and was a distinct improvement on the three-bench method of drilling used previously (1). During 1937 and 1938, when experienced miners were available, Leyner long-hole drilling was carried on with great efficiency. However, in 1939 and 1940, labour turnover in-creased and experienced long-hole drillers became scarcer. This resulted in a marked decline in the efficiency of the drilling operations, with increased costs and less tonnage drilled per shift. EXPERIMENTAL WORK The initial diamond drilling test work was carried on with a Longyear 3420 air-driven blast-hole drill rig, drilling a 1 3/16-inch hole. Tests indicated that diamond drilling could be successfully adapted to local conditions and that overall costs compared favourably with costs obtained with the Leyner long-hole method. Leyner long holes on stope benches usually bottomed at a larger diameter than the 1 3/16 -inch diamond-drill holes. More powder could therefore be introduced into the Leyner holes than could be placed in the diamond-drill holes. To achieve the same fragmentation, additional footage was required when diamond drilling. Diamond-drill holes of larger diameter were indicated.

Jan 1, 1943

By C. Lara-Valenzuela, R. Perez-Garibay, F. López-Saucedo, A. Uribe-Salas, L. Magallanes-Hernandez

A relationship between gas dispersion parameters, namely gas rate (Jg), gas holdup (Eg), average bubble size (db) and bubble surface area flux (Sb), with the metallurgical performance (e.g., grade and recovery) has been established.. Results of eleven columns operating at five concentrators of Grupo Pefioles (Mexico), ranging between 1.52 to 3.35 min diameter and performing in the cleaning stages of lead and zinc circuits, are presented and discussed. The results showed that the effect of gas dispersion parameters was consistent and that both, Sb and Eg, correlate well with recovery particularly when the influence of feed pulp density is also considered.

Jan 1, 2009

By L. Mercier, R. Narendrula, F. Desmarais, L. Amaratunga, A. Aledresse

Thiosulfate is recognized as a promising alternative lixiviant to cyanide for the extraction of gold from ore bodies. Gold thiosulfate ([Au(S2O3)2]2), however, is not well-adsorbed by activated charcoal, making industrial scale use of thiosulfate for gold leaching impractical at present. Because of their high specific surface areas (500-1000 m2g-1) and uniform open-framework nanoporosity (pore channel diameters in the range 3-10 nm), functionalized mesoporous silicas are widely recognized as highly effective materials for the selective, rapid and high capacity uptake of mercury, gold and platinum group ions. In the present work, the efficient and rapid adsorption of gold thiosulfate by thiol-functionalized mesoporous silica (hereafter designated MP-HMS) is demonstrated, whereby the thiol groups in the materials bind with the gold complexes by ligand displacement. The adsorbed gold could be leached out using cyanide, regenerating the adsorbent for further uptake cycles. Functionalized mesoporous silica is thus a promising candidate for the preconcentration of gold from thiosulfate leachate solutions.

Jan 1, 2011

By D. Y. Li, C. D. Ma, T. Zhou, T. J. Cheng

In this paper, a number of experimental tests are carried out to study the strength difference on rectangular prismatic marble specimens with different height-to-width (H/W) rations. The specimens have a nominal size of 45×15 mm in the compressive cross-section (W×T) and different heights (H = 22.5 mm, 45 mm, 60 mm and 90 mm). It is to say that the height-to-width ratios are equal to 0.5, 1.0, 1.33 and 2.0, respectively. The quasi-static uniaxial compressive tests are finished by a servo-controlled INSTRON machine (the strain rate at about 10-5/s), and the dynamic compressive tests are finished by a diameter of 50 mm cylindrical SHPB apparatus (the strain rate reaching about 101/s). The rock failure process of marble specimens is captured by a high speed camera in order to distinguish the fracture propagation behaviour. It is found that the compressive strengths increase when the H/W ratio of marble specimen changes from 2.0 to 1.0 due to the end clamping effect both for quasi-static and dynamic loads. However, when the H/W ratio changes from 1.0 to 0.5, the apparent compressive strengths decrease both for the two loading conditions. The strength decrease of short marble specimens may be attributed to the change of failure mode from shear to slabbing, which can be identified by the fracture patterns of the specimens. Based on the uniaxial compressive tests, the slabbing strength of the marble was found to be about 40% of its UCS for the specimens with a nominal height-to-width ratio of 2.0. In addition, it is found that the dynamic increase factors (DIF) are affected by the specimen’s aspect ratios. It implies that the same aspect ratios should be used to compare the dynamic and static compressive strength of rocks. Meanwhile, both the static and dynamic tensile strengths of the marble are obtained by the Brazilian disc tests. The ratio of the dynamic tensile strength to the static tensile strength of the marble is about 2.68.

Jan 1, 2015

By Stéphane Chevrel

Non-energy raw materials are vital inputs for the EU?s economy and maintaining fair and undistorted access to these materials for EU industry and citizens is increasingly difficult. Within the EU, exploration and extraction have to face increased competition for different land uses and a highly regulated environment. While the EU is currently dependent on the importation of many metals, the overall potential for mining and quarrying in Europe is strong. In spite of this, the land area available for extraction in the EU is constantly decreasing, turning access to land into a key challenge for the extractive industry. The EOMINERS project aims at contributing to demonstrate how to improve the EU capacity in implementing new mining sites and their societal and environmental acceptability. The overall aim of EO-MINERS (Earth Observation for Monitoring and Observing Environmental and Societal Impacts of Mineral Resources Exploration and Exploitation) is to bring into play EO-based methods and tools to facilitate and improve interaction between the mineral extractive industry and the society in view of its sustainable development while improving its societal acceptability. EO offers a unique opportunity to collect necessary spatial parameters that play a key role for better assessments of mining-related environmental and societal impacts. It could enable the development of means to identify the site-specific environmental and societal footprints of mineral resource extraction and to determine their respective significance. This understanding of global and cumulative footprints along a causal chain is needed in order to target policy measures. In this way the expected reduction of environmental and societal footprints in the mining sector can be most effective for the environment and more cost-efficient for public authorities and commercial operators. The project first defined environmental, socio-economic, societal, and sustainable development indicators and criteria that can possibly be dealt with using EO techniques. After an analysis of policies related to the environmental and social footprint of mineral industries, project expertise and stakeholder interviews (national and on-site) as well as site investigations led to the establishment of a list of indicators to be monitored, either directly or indirectly, through accessible parameters. Development of EO-based monitoring tools is then carried out over three demonstration sites: the lignite open pit of Sokolov in Czech Republic, the Mpumalanga coalfield centred on the town of Emalahleni (previously Witbank) in South Africa, and the Makmal gold mine in Kyrgyzstan. From these developments, it is subsequently intended to contribute to the development of generic, standardised EO data integration schemes, in particular in view of characterising affected ecosystems, populations, and societies and prepare indisputable documents that will make the basis for a sound ?trialogue? between industry, governmental organisations, and stakeholders. This paper discusses results obtained after three years into the project, focusing on product development over the demonstration sites and their relevance to the observation and monitoring of environmental and societal footprints of the extractive industry.

Aug 1, 2013

By D. Pearcey, S. T. Vessey, V. Hegde, J. Staples

"Pellet quality has taken on a new dimension during the last ten years. Quality in the seventies was generally defined as adherence to certain physical and chemical specifications. Today, the talk is in terms of how the business is managed, how customer's expectations can be exceeded, not only in product quality, but in service responsiveness.Coke breeze and flux additions, lower silica levels, and improved furnace control practices have all contributed to the improvement of pellet physical and metallurgical properties. Statistical process control has provided additional insight into the parameters that affect pellet quality.Increased customer contact and product quality surveys have heightened our awareness of customer needs and also provide direction for quality improvement test work. Current work is focussed on improving reducibility and understanding the relationship between tumble, fired compression and metallurgical properties.This paper will review the Iron Ore Company of Canada's efforts during the past decade and describe some of its initiatives for the future.IntroductionThe Carol Pellet PlantThe Iron Ore Company of Canada's Carol Project is located in Labrador City in the southwestern portion of Newfoundland and Labrador , approximately 965 Ian northeast of Montreal. The project consists of mining facilities, beneficiation complex and a pellet plant, which began operations in 1962. The pellet plant consists of six Dravo-Lurgi straight grate machines, regrinding, filtering and balling facilities. The current capacity of the Carol pellet plant is approximately 10.5 million tonnes , while the concentrator has the capacity to produce about 18 million tonnes of concentrate.The orebody consists of specular hematite, magnetite and small quantities of limonite and goethite. The average grade of the orebody is approximately 39% iron."

Jan 1, 1991

By J. R. Morris, A. E. Ball, G. W. Kuzyk

"AECL Research has constructed an underground laboratory for the research and development required for the Canadian Nuclear Fuel Waste Management Program. The experimental program in the laboratory will contribute to the assessment of the feasibility and safety of nuclear fuel waste disposal deep in stable plutonic rock.In 1988, AECL extended the shaft of the Underground Research Laboratory (URL) from the existing 255 m depth to a depth of 443 m in cooperation with the United States Department of Energy (USDOE). The project, which involved carrying out research activities while excavation and construction work was in progress, required careful planning. To accommodate the research programs, full-face blasting with a burn cut was used to advance the shaft. Existing facilities at the URL had to be modified to accommodate an expanded underground facility at a new depth. This paper discusses the design criteria, shaft-sinking methods and approaches used to accommodate the research work during this shaft extension project.IntroductionThe Underground Research Laboratory (URL), a major geotechnical research facility, has been developed by AECL Research, 120 km northeast of Winnipeg, Manitoba. The URL is part of the Canadian Nuclear Fuel Waste Management Program (CNFWMP), which is assessing the concept of nuclear fuel waste disposal in a vault deep in stable plutonic rock of the Canadian Shield (Hancox, 1986). The URL provides a representative environment to conduct a wide variety of geotechnical research relevant to nuclear waste disposal. Extensive characterization and monitoring programs were carried out prior to construction and will continue during operation. The operating phase experiments began in 1989 and will continue until the year 2CXXl (Simmons, 1990). Figure I shows the present extent of the URL facilities and the proposed future development."

Jan 1, 1991

By Adriana Ramirez, Bradford C. Wesstrom, Blanca Olave

The Freeport McMoRan El Paso Copper Refinery optimizes electrolyte quality using a number of systems. The facility controls copper, arsenic, antimony and bismuth using electro-winning cells within the Tank House and Nickel Carbonate Plant Liberator Circuit (NCP). The NCP manages sulfuric acid content utilizing recycled electrolyte in the slimes autoclave as well as operation of the Acid Purification Unit, APU. The El Paso Refinery removes common sulfates using metal hydrolysis with sodium carbonate. Finally, a Mechanical Vapor Recompression, (MVR), at the water recovery plant removes sodium sulfate generated by the NCP. This paper will provide a summary of these operations. INTRODUCTION In the mid 1920’s Nichols Copper Company, in Laurel Hill, New York, recognized the need for a modern copper refining facility in the southwest. Because of the many railroad heads, affordable power and abundant labor supply, and the close proximity to regional copper smelters in Mexico, Arizona, and New Mexico, El Paso became the ideal location. In December 1928, ground was broken for the joint venture refinery between the Nichols Copper Company, Phelps Dodge, and the Calumet and Arizona Mining Company. In September 1930, Nichols Copper Company became a part of Phelps Dodge Corporation after a stock exchange. In July 1938, Nichols Division officially became Phelps Dodge Refining Corporation. In March 2007, Freeport McMoRan Copper & Gold acquired Phelps Dodge. Water is a precious commodity in the desert southwest, making conservation of this natural resource an important goal for the El Paso Operations. In the 1980’s, work on the treatment of slimes was improved through the use of pressure leaching of the refinery slimes using an autoclave. Due to the high tellurium content in the leached slimes solution, it was crucial to implement a method for its removal before the solution returns to the tank house electrolyte. A copper telluride cementation operation was installed for tellurium recovery and the ability for the recycle of the leachate and wash water to the refinery electrolyte. In October of 1997, ground was broken for the construction of the water recovery plant using an MVR to reuse process water, reducing water consumption by 25%. In 2002, electrolyte purification was further improved with the installation of an Acid Purification Unit, (APU) (Sheedy, Pajunen, & Wesstrom, 2007). The APU recycles 90% of the acids (both sulfuric and arsenic acids) back to the tank house electrolyte. The solution that passes through the APU is treated with soda ash to precipitate metals out of solution as carbonates and generates a sodium sulfate solution. This sodium sulfate solution is easily processed in the new water recovery plant, where the majority of the water recycles back into the plant as pure condensate. In 2012, the power plant at the refinery upgraded its Reverse Osmosis System to provide RO water to the tankhouse. This insured that the refinery would not have to bleed electrolyte for metals contained in well water such as: calcium, magnesium, iron and sodium chloride.

Jan 1, 2019

By A. J. Basu

Air quality in underground mining operations can fluctuate significantly during the working day, but until recently the only way to ensure a mine had sufficient air quality was to over-ventilate and, with significant delay in adjusting the volume or direction of the airflow, working conditions were tolerable but rarely ideal. Underground ventilation management systems have been considered to achieve improved energy efficiency since at least 1995 in Canada. However, Mine Ventilation Optimization, (MVO) and integrating it with Ventilation on Demand (VOD) is only becoming more of a reality in the last seven (7) years. A systems approach to MVO takes into account all the elements from the point the power is distributed into the ventilation fans through to the actual quality and quantity of fresh air to the working face. Opportunities exist throughout the system for energy savings but not all of them are cost-effective. Depending on the application, these opportunities can be easily realized by properly sizing, streamlining, maintaining and operating the ventilation system using premium mine proven energy efficient components throughout. Implementation of VOD is a key step in achieving the MVO objective. However, VOD is a concept, and it requires various tools, procedures, and strategies for cost-effective and operationally viable implementations. This paper provides a historical background in the development of VOD and provides a framework for proper and cost effective implementation. In addition, an optimized ventilation system will also allow increased airflow by reducing resistances and shock losses. This turn in would allow production target improvement, which could be an attractive objective compared to energy savings. Mine ventilation is the life support system of an underground mine, and contributes to sustainable development and corporate social responsibility goals assuring health and safety aspects of strategic planning. The proposed framework addresses implementing mine ventilation optimization integrating ventilation on demand as a vehicle for energy, health and safety improvement and overall productivity gains in the mining cycle efficiency while significantly reducing carbon footprint of a mine.

Aug 1, 2013

By R. P. Mahant

"Extensive pilot plant investigations were conducted both on partial roasting an d electric furnace smelting from September 1973 to August 1975.The objectives of the pilot plant investigations were:(I ) to confirm the application of available process technology to treatment of Falconbridge concentrate.(2) to examine partial roasting variables.(3) to investigate electric furnace smelting of roaster calcines .(4) to develop process design and operating parameters for a commercial plant.This part of the paper will cover the following topics:Partial Roasting InvestigationsPilot Electric Furnace InvestigationsPartial Roasting InvestigationsThe specific objectives were to:1. establish process variables for maximum oxygen efficiency and bed fluidi ation.2. determine the product distribution between the roaster and the various gas cleaning stages.3. produce a mass and thermal balance."

Jan 1, 1984

By W. Wallace

The aerospace industry celebrated 100 years of powered flight in 2003, and the remarkable achievements that have occurred during the past 100 years are in no small way due to major developments in materials. Modern alloys for airframes, engines and other major sub-systems have evolved through the intelligent application of new processing concepts involving melting, casting, hot and cold working, heat treatment and more recently vapour phase processing. Alloy design has evolved in parallel to allow maximum benefits to be achieved from these processing advances. However, the pace of development seems to be slowing and future gains are likely to be made by learning how to extract major value from aerospace assets. Understanding the modes of deterioration and establishing cost effective lifetimes by holistic life cycle management seem to be the way of the future. Extending component lifetimes by repair, rejuvenation and refurbishment are all viable possibilities and they offer great opportunities for Canada, which, traditionally, has been a major user of modern aerospace materials rather than a supplier. The challenges for metallurgist, physicists and engineers will be no less than in the past and should create new business opportunities for Canada. The scenario described above will be developed by calling upon examples drawn from the author's experience.

Jan 1, 2004

By Feng Tianran, Lu Shijie, Shen Zhengchang, Han Zhibin, Tan Ming

"As a kind of non-metallic material, high-purify quartz sand has been widely used in many fields. Flotation is a popular way to process quartz sand. But it is in difficult position for flotation to get high-purify quartz product due to large amount of coarse particles contained in the feed. In this paper, a design principle of special flotation cell for high-purify quartz sand has been put forward base on ore property analysis and laboratory test, and the pilot scale special flotation cell has been developed to meet the requirement of the quartz sand flotation process. The special flotation cell for high-purify quartz sand is featured by middle positioned impeller, false bottom and draft tube, which could decrease the rising distance of mineralized bubble and strengthen the circulation capacity of the lower part of the flotation cell. Hydrodynamic study indicates that high air dispersion degree and strong lower slurry circulation could be produced by pilot scale special flotation cell, which is helpful to create a suitable hydrodynamic environment for quartz sand processing.INTRODUCTIONNatural quartz is a non-metallic mineral, which is widely used as raw material in multiple industry process (Shifu, 2006). High purity quartz, especially containing more than 99.9% silicon dioxide, is characterized by high temperature resistance, small thermal expansion coefficient, highly insulating and so on. The demand of high purity quartz has been rising along with social and economic development, now high purity quartz is widely used in the field of photovoltaic industry, electronic information, communications and aerospace industry.Quartz is a kind of main rocking-forming minerals in the nature. There are seven genetic types, such as natural crystal, quartz sandstone, quartzite, vein quartz, konilite, natural siliceous sand, granite quartz (Baolei, Shuilin, & Dianchao, 2012). The natural crystal is primarily used as raw material to refine high purity quartz, but it is not available for two reasons. On the one hand, the natural crystal is extremely expensive and poor in resources reserves, which can not satisfy the need of large-scale industrial production. On the other hand, the chemical component of natural crystal is instability, it may lead to low stable product performance in large industrial applications, and it is also difficult to achieve raw materials standardization. Therefore, there are a lot of studies to search for other technological methods to obtain high purity quartz from other genetic quartz types."

Jan 1, 2016

By R. Cottam

The deformation and recrystallisation of magnesium yttrium alloys containing 0.23, 0.84 and 2.71wt% yttrium and commercially pure magnesium extrusion has been investigated at temperatures between 200 and 350°C. The alloys were produced as billets 7.5 cm diameter, solution treated at 525 °C for 8 h and extruded into 3 cm diameter bar at 390°C. Channel die compression was employed to deform the samples at a strain rate of 1x10-3s-1. For the 0.23 wt% yttrium alloy and the pure magnesium, dynamic recrystallization (DRX) occurred at all temperatures and the amount of DRX increased as the temperature was raised. In the alloys containing 0.84 and 2.71 wt% yttrium DRX was almost completely suppressed at all temperatures. The absence of DRX in the 0.84 and 2.71 wt% yttrium alloys was accompanied by a decrease in the ductility, except at 350°C the highest deformation temperature. It was observed that this increase in ductility was accompanied by a reduction in deformation twinning and the initiation of pyramidal slip. This work highlights the important role that DRX plays in enhancing the ductility of magnesium alloys.

Jan 1, 2006

By R. J. McLeod

"A new backfill plant was constructed in 1966 adjacent to the mill of Giant Yellowknife Mines. The reasons for the addition were to increase the storage capacity for sand fill, provide facilities for mixing cement with the fill for mine stope floors and provide a system for pumping fill to B -3 raise, a horizontal distance of 4700 feet from the mill. At the same time it was hoped to increase the density of the fill pumped underground.The plant consists of two only steel storage tanks of approximately 400 tons capacity of sand fill each. They are 17 feet in diameter and have conical bottoms. The cylindrical section is 28 feet high and the conical section 14 feet high. Each tank is fitted with water nozzles around the conical sections to remove solids at the required density. The water pressure on the nozzles is 150 lbs per square inch. The cyclones used to produce the sand back fill are located on top of the storage tanks. Five model Dl0B Kreb cyclones are used for this purpose. The vortex finders are 2 1/ 4 inch and the apex 1 1/4 inch. The cement silo or storage tank is located in the same building. It is a steel tank 17 feet diameter by 41 feet high with a conical bottom. The silo holds 250 tons of bulk cement, which is unloaded by air from a bulk highway carrier using 12 to 15 lbs air pressure. The cement is conveyed to the top of the silo, a distance of 70 feet from the ground by 450 lbs. of air.The mixing tank is a rubber lined steel tank 14 feet in diameter by 14 feet high. It is equipped with a Lightning Mixer supplied by Greey Mixing Equipment Ltd. The mechanism is driven by a 40 HP motor. The lower shaft is unsupported and is equipped with two 36 inch diameter axial flow turbine type rubber covered impellers. The backfill is discharged from the storage tank into the mixing tank by a 5"" x 4"" SRL-C pump powered by a 20 HP motor. A level control in the mixing tank regulates the rate of discharge of this pump through a Grinnell-Saunders automatic control valve. The cement silo is situated at such a height above the mixing tank to allow for a Rota-Lock, a small hopper and a cement feeder. The feeder is an Omega gravimetric belt type dry feeder with a Sensogram controller. The capacity of the cement feeder is 20 tons of cement per hour. The cement and backfill are mixed in the mixing tank at whatever ratio is required for the mine stope floors."

Jan 1, 1968

"Eastern Canadian thermal coal mined at Minto, New Brunswick, and in western Cape Breton at St. Rose, Inverness County, Nova Scotia, contains 6-8 per cent sulphur. Both coals are high volatile bituminous. types. The Minto coal averages 18 per cent ash, 7 per cent sulphur and has a Btu rating of 11,900 per lb. Pyritic sulphur accounts for 75 per cent of the total sulphur and the remainder is largely organic; the amount of sulphate sulphur is negligible. This means that in a 7 per cent sulphur coal, 2 per cent is organic and 5 per cent pyritic sulphur. Pit-head St. Rose coal contains approximately 10 per cent ash, 7 per cent sulphur and 11 ,800 Btu/lb. The distribution of sulphur is different to that of Minto coal because about 12 per cent sulphate sulphur is present. Thus, a 7 per cent sulphur coal would contain 4 per cent pyritic, 2 per cent organic and 1 per cent sulphate sulphur.The iron sulphides, pyrite and, to a lesser extent, marcassite occur over a wide size range from large sulphur balls to crack fillings, lenses, and individual crystals and framboids. Coarse-grained pyrite and sulphur balls are easily separated during washing. It is the fine grain sizes, intimately mixed with the coal constituents, that are difficult to separate. Quantimet analyses of the fine grains in coal from both localities showed that about 50 per cent were smaller than 30 micron(1).No efforts have been made to wash the Inverness coal of Nova Scotia and in 1980 washing ceased in New Brunswick. Previously, the Minto coal was processed in an antiquated jig circuit which reduced ash from the strip operation run-of-mine value of more than 20 per cent to less than 18. More effective removal of ash and sulphur could clearly be obtained. Laboratory tests on both Minto and St. Rose coal have shown that ash rejection rates of 40 to 50 per cent at yields of 70-80 per cent were possible(2), Little information on sulphur removal was available."

Jan 1, 1981

By G. W. H. Norman

The surficial Archæan rocks of the southern gold belt of western Quebec are constricted near Kewagama lake by granite masses to the north and south. This divides the belt into natural eastern and western parts. This paper deals with the eastern part, extending from Malanie to Haig township. In this section the Keewatin-Timiskaming rocks have a length of about 70 miles and end abruptly against garnetiferous gneisses of the Grenville terrain. In the western half of the section where exploration has been under way since the early twenties, there are sixteen mines that are or have been in operation, and eleven prospective mines. In the eastern half where exploration has been carried on since the early thirties, six prospective gold mines are under development, one· of which, Louvicourt Goldfields, is at the initial production stage. Of the sixteen properties in the western half that are operating or have operated, all, except the Golden Manitou, which is a base metal mine, and the old Green Stabell from which there was a small production of copper, produce gold. Of the eleven prospective mines in the western half nine have gold. New Bidlamaque has gold and copper and one, East Sullivan, has copper-zinc ore. Since production began in 1927 gold, silver, zinc, copper, and lead having a total value of about $10,000,000 have been produced from the mines of the eastern section of the southern gold belt of western Quebec.

Jan 1, 1954

By H. W. Little

INTRODUCTION MINERAL deposits of Salmo map-area (Figure 1) have aroused the interest of prospectors for more than a half-century. Properties within the map-area have produced lead, zinc, silver, tungsten, and gold. Sheep Creek mining camp ranks fifth in the Province in the total production of gold, but during recent years interest has been concentrated upon base metals, and meticulous prospecting and exploration have resulted in the discovery of many large zinc-lead orebodies. PREVIOUS WORK Geological investigations of the region were begun long ago, and it is interesting to trace the development of ideas with our increasing knowledge of the geology of this complex area. The first geological examination of the rocks of Salmo map-area was made in 1859-60 by H. Bauerman (1), who was employed as geologist accompanying the first international Boundary Survey. Bauerman examined the rocks exposed along Pend d'Oreille river and published a section indicating that the sedimentary rocks are probably of Palaeozoic age, and are intruded by granite of unknown age. McConnell and Brock(2), in 1894 - 1900, carried out the reconnaissance mapping of the West Kootenay Sheet, on which they outlined the Mesozoic rocks of the Rossland Beaver Mountain volcanic groups that they believed rested unconformably upon the sedimentary rocks to the southeast, which they regarded as of Palaeozoic age.

Jan 1, 1951

By Philippe Ribagnac, Bruno Courtaud, Jean-Marie Lambert, Valérie Weigel

Mabounié is a polymetallic deposit in Gabon containing niobium (1.2 wt.%), tantalum (0.03 wt.%), rare earth elements (REE) (1.4 wt.%) and uranium (0.03 wt.%) that are mostly carried by pyrochlore minerals. The classical route for niobium recovery is a pyrometallurgical process that consists of pyrochlore flotation, dephosphorization of the niobium concentrate and aluminothermy to obtain ferro-niobium. Pyrochlore concentrates can also be treated by a hydrometallurgical process with a mixture of sulfuric and hydrofluoric acid leaching followed by solvent extraction to separate niobium and tantalum. However, the first process does not allow recovering REE and the second one is not environmentally friendly because of the use of HF. ERAMET is looking for new opportunities on strategic metals market and has recently developed a hydrometallurgical process for the recovery of all these metals based on a sulfuric acid treatment of the ore (Donati, Courtaud, & Weigel, 2014). As for most of the oxidized ore processes, the major impurity is iron (~30 wt.%). Thus, in this hydrometallurgical process, the question arises of the elimination and stabilization of the iron as residue. The iron in solution is ferrous; goethite precipitation seems the most adapted crystalline form. Lab and pilot tests have shown kinetics of precipitation of 6 g.L-1.h-1 at pH 4.5. To reduce the salt discharge, sodium-jarosite form is more adapted, but at pH 2, 95°C only 30% of iron is precipitated in 5 hours, compared to 100% in goethite form at the same time and pH 2, 80°C. Different ways of oxidation were tested, air, pure O2, activated carbon, without drastic effect. The more efficient was ozone use, at room temperature; the kinetics of oxidation is five time faster than the other ways with 30% of sodium removed from the solution.

Jan 1, 2016

By F. Rojas, M. Sanchez, J. Palacios, O. Pavez

Copper sulfide is the main mining resources in Chile, and most of this metal is obtained via pyrometallurgical extraction in seven copper smelter plants, which extends from the northern Atacama desert to the central part of the country. In 2002, 1,522,000 metric tons of fine copper were produced, with a notorious environmental impact due to the large amount of slag generated, including transportation and disposing problems. Therefore, there is a great interest in finding alternative uses in order to give additional value to the slag. This is a total project development concept, which consider residues as new resources where new components could be obtained, improving sustainability in mining activities and also ensuring clean production processes. Thus, the present work shows a review of copper slag characterization as well as several ways of utilization, including compact material for road and railway installation, part of admixtures in concrete.

Jan 1, 2004

By Joerg Hammerschmidt, Marcus Runkel, Steffen Haus

Given the limited number of new plant construction, focus is turning to the optimization of existing metallurgical roasting plants. To meet the goals of high process efficiency with limited capital expenditure, plant owners are looking for new strategies, including digitization and expert support. As a supplier for numerous roasting, gas cleaning and sulfuric acid plants, Outotec has intensified its effort in recent years to develop solutions to accommodate increasing customer need. This article presents a short review on how Outotec is applying advanced control tools for the fluidized bed industry. Focus will be given on how to transfer the existing technology (used in selected Zinc roasting plants for over a year now) to copper roasting. Outotec has developed the Pretium Roaster Optimizer, a system based on heat and mass-balanced simulation models. Direct experience with this technology will be shared and will highlight similarities to the Partial and Sulfate Copper roasting processes. Pretium detects equipment and plant bottlenecks and provides consistency in process development. The Pretium program combines 24/7 advanced online digitalization tools, along with expert personal support when required. INTRODUCTION Fluidized bed reactors have been used for commercial-scale zinc and copper roasting since the 1950s. While the principles of roasting remain unchanged, over time, the technology has advanced to improve process control of roasting plants. In the past, environmental and safety standards were the driving forces for improvement of equipment and plant design. Today, the emphasis is on plant efficiency and optimization. Another change has come in process control philosophy. While plant control and operation have traditionally been the responsibility of owner/operators, they have now shifted to include both integrated digital tools and specific know-how from engineering companies. This can be seen from the earliest design stages through commissioning and into production, as evidenced by zinc roasting plants in Mexico, Brazil and Turkey.

Jan 1, 2019