Search Documents

By John Crusius

? 3-year research program overview ? initial results- MainZone pit Waterline pit ? questions raised ? increasingly common in western N. America ? frequently low-pH waters with elevated concentrations of many metals ? water quality controls poorly understood ? some in U.S. are Superfund sites

May 1, 2002

By Elizabeth Edwards, Radhakrishnan Mahadevan, Vladimiros G. Papangelakis, Srinath Garg, Kurtis Judd

Mineralogical characterization of the tailings showed the deportment of Ni to be similar in the Vale and Glencore tailings, with 60% of the total Ni locked in pyrrhotite, and the balance 40% associated with pentlandite. The overall Ni dissolution was correlated with the individual dissolution extents of pyrrhotite and pentlandite as functions of four leaching regimes: ‘anoxic acid’ (with and without pH control), ‘oxic acid’ (oxygen sparging), ‘oxic acid’ (air sparging), and ‘oxic ferric’ (air sparging). The results showed that the maximum Ni dissolution was obtained during the pH controlled oxic acid leach with oxygen sparging at pH 1.5, while the anoxic acid leach at pH 1.5 resulted in minimum Ni dissolution (10–15%) from pyrrhotite. An overall Ni mass balance showed that pyrrhotite and pentlandite dissolve simultaneously in the presence of Fe(III) and oxygen, in contrast to the preferential dissolution of pyrrhotite in the absence of Fe(III). Sulphur mass balances revealed that the yield of elemental sulphur is maximized (65%) during the oxic Fe(III) leach at pH 0.6. Furthermore, the kinetics of Ni leaching and elemental sulphur formation from pyrrhotite tailings leached with ferric sulphate between 55–80°C was investigated at constant oxidation-reduction potential. Elemental sulphur yield increased with increasing temperature, but no observable trend could be linked to ferric or ferrous ion concentration.

Jan 1, 2017

By Jean-Yve Tremblay, Michel Prud'homme

"Industrial minerals include a group of more than fifty minerals which are marketed into almost all the sectors of industry; they are the backbone of many manufacturing industries. Table I shows major end-uses for industrial minerals in manufacturing sectors. At Energy, Mines and Resources, industrial minerals are divided in three major categories: (I) agro chemicals and chemicals, (2) construction mineral s, and (3) ceramics and specialty minerals. A listing of the major groups of minerals is shown in Table 2. Agro-chemicals and chemicals are sold on the basis of their chemical content and purity. Construction minerals or structural minerals are distinguished by their performance as low cost and bulky commodities. Ceramics and specialty minerals are performance-specific and are sold for their property on imparting functions on end-products. Industrial minerals have unique characteristics that are useful in many stages of processing; from crushed size to micronized fillers a single mineral ca n serve a broad range of industries because of its intrinsic properties."

Jan 1, 1988

By Abani R. Samal

The Fe assay values from the diamond drill-holes within a magnetite deposit of magmatic origin are utilized in this study. Only assay data from the unoxidized magnetite mineralization was utilized. The data from the overlying hematite mineralization zone was not used. A threedimensional block model estimated using ordinary kriging (OK) is used for analysis purposes. To estimate the non-linear standard deviations (s) and the confidence intervals (CI) of block estimates a discrete Gaussian variogram model is used in this project. The change-of support coefficient (rv) and the block-support correction are used in the ?block-anamorphosis?. A new calculated value of rv is 0.7283, implies that its influence in the block-anamorphosis is not significant. The CIs are calculated from the block-gaussian variables; then back transformed to the raw values. At 95% probability, the CI for the kriged block estimates of Fe values are calculated using Gaussian kriged estimates of the Fe and the corresponding standard deviations (Gaussian). The results indicate that the block estimates with a high influence from relatively small amount of samples can be identified as high-risk estimates.

Oct 1, 2009

By I. H. Warren

"An analysis of form-coking processes is presented in terms-of their fundamental mode of operation and their relationship to other coking processes. Their possible future role in cokemaking is assessed. IntroductionAny consideration of prospects and possibilities for form coking must commence with the iron and steel industries-their likely future growth pattern on a world and regional basis and the potential direction of future developments in iron and steelmaking technology.From the numerous estimates which have been made of the future consumption of steel, it would appear that a growth rate of 3lllo between now and the year 2000 is likely. Radical changes in steel making technology are unlikely to be commercially adopted on any significant scale during the next twenty years . However, widespread commercialization inter alia of continuous casting and direct reduction, growth of electric furnace steelmaking and a decrease in coke rates will all contribute to a growth rate for metallurgical coke that certainly will be less than that of steel."

Jan 1, 1980

By Yve Aymong

"The objective of this paper is to help readers benefit from the practical experience of persons who have been engaged for several year s in the testing and repair of power transformers. Power transformers are known to be reliable pieces of equipment with expected usage of 25 to 30 years, but simple problems such as leaking radiators, or a bad contact on a tap changer, could shorten the life of a transformer. To ensure a longer life span, transformers should be checked on a regular basis.What is a Power Transformer?It can be a 90 MVA transformer for Hydro-Québec or a power transformer can be a 500 KVA unit in a small hospital. Generally a power transformer is an oil -filled type of 3 to 5 MVA. It can also be a dry type transformer, that should be treated in the same manner as oil-filled transformers, and some of the tests explained in this paper also apply."

Jan 1, 1984

By S. Koski, M. Schmalzel, D. A. Jacobson, S. Crosby, P. Cook, M. Mular

"Mining operations, whether new or existing, are constantly looking for ways to maximize production and improve energy efficiency, while keeping the footprint required to a minimum. The Nordberg MP1250 cone crusher was designed with these three goals in mind. A series of side-by-side evaluations comparing an MP1250 to an MP1000 were completed at two Freeport-McMoRan operations. The first evaluation began October 2009 in a tertiary position and the second began March 2010 in a secondary position, where it remains in full production today. Utilizing 25% higher power capacity than the existing MP1000 tertiary crushers, the MP1250 had 29% higher capacity and 17% lower specific energy, adjusted for differences in feed and product size. The MP1250 compared to the existing MP1000 secondary crushers achieved 30% higher capacity at a slightly reduced specific energy, while achieving a finer product.The MP1250’s higher capacity and energy efficiency may have application in many crushing plants. Depending on site specific economic factors, greenfield projects may benefit from a smaller footprint and less ancillary equipment, whereas brownfield projects may benefit from higher capacity or a finer product within the same footprint."

Jan 1, 2012

By Gustavo Brunello

Motor Failure Rates and Cost ? Motor failure rate is estimated: 3-5% per year. ? In Mining, Pulp and Paper industry failure rate is up to 12%. ? Sometimes process downtime costs are higher than motor ?? Motor failures are due: Electrical 32% Mechanical 31% Environmental 36%

Feb 1, 2008

By George McIsaac

This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development and mining method. Based on practical considerations, maximum rates are set for each zone?s development and production capacity. As for the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum number of development metres per day is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Furthermore, the fixed cost of operating the mine is taken into consideration whenever mining activities take place. Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analysed. What-if scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan.

May 1, 2003

By S. Itoh, T. Nagasaka, J. Ono

With respect to the recycling of used lead-batteries, a pure lead is required to prepare a lead-calcium alloy electrode for a new maintenance-free battery. The pure lead can be obtained by means of electrolytic and/or pyrometallurgical refining. In the lead electrorefming, antimony is concentrated in anode slime. From the viewpoint of the recycling and recovery of metal values from used lead-batteries, especially from anode slime, oxidation experiments were conducted for pure liquid antimony in the temperature range between 973 and 1373 K to elucidate the oxidation kinetics and mechanism. Furthermore, since lead anode slime generally consists of antimony, lead and bismuth, experiments have been also carried out using antimony-lead-bismuth alloy. The equation relating to the mass transfer characteristics in the gas phase was then applied to analyze the oxidation kinetics. As a result, it was found that the anode slime treatment, that is, an oxidation of antimony concentrated in anode slime followed by vaporization as antimony oxide Sb406, should be operated with higher oxygen partial pressure and sufficient amount of gas flow rate at lower temperature around 1073 K. The feasibility of the oxidation treatment for anode slime has been also discussed.

Jan 1, 2004

By R. C. Reed, A. Akhtar

Oxidation of the third generation cast single crystal, nickel-base superalloy CMSX-10 is examined using isothermal tests at 900°C and 1000°C for times ranging from 20 hours to 100 hours. X-ray diffraction, scanning electron microscopy and energy dispersive secondary X-ray analysis were used to characterize the microstructure. It was found that the external scale formed at 1000°C is made up of (Ni,Co)O and the spinel NiCo2O4. The (? + ? ') microstructure of the superalloy transforms into the intermetallic (3 phase prior to the onset of internal oxidation. Internal oxidation results in the formation of (Ni,Co)Ta2O6 and (Ni,Co)WO4. No evidence was found for the formation of alumina (Al203), and the spinels NiCr2O4 and NiAl2O4 in this third generation superalloy. Results of the laboratory investigation are compared with those of an aero-engine turbine blade removed from service and examined earlier.

Jan 1, 2004

By Doug Ashbury

Diamond Miners? Challenges ? Remote ? 300 kilometres from Yellowknife ? Sub-Arctic conditions ? permafrost, climate ? No power ? No all-weather roads ? Ore bodies difficult to find ? Caribou, fish of special concern ? Communities with low education, little experience, but high expectations ? Major investment required ? Diavik C$1.3 billion

Apr 1, 2005

By F. McIntosh Galbraith

EMPLOYING geophysics to find ore was for a long time considered by the Canadian mining fraternity to be a performance of dubious value: in a category somewhere between the practice of sorcery, and using a divining rod to locate underground water. With increasing knowledge, however, and with constantly improving instruments, a solid speaking acquaintance with this adolescent science is becoming an integral part of the mining geologist's stock in trade. And quite properly so: for, in the established mining districts, the ore deposits which could be easily found, by ordinary prospecting methods, have already been located. There remain; however, in almost all of the principal mining camps, areas which are covered to varying depths by glacial debris; and it is here that the obvious opportunities exist for the successful application of geophysical methods. Geophysical results must always be considered in the closest possible relation to the local geology; and, in reality, the 'doodle-bugs' are simply additional tools for the geologist (in the same category with a plane table or a microscope). The Sudbury Basin is a shining example of precisely this state of affairs. Detailed geological mapping has not significantly altered the position of the outer norite contact as placed on Dr. Coleman's original map of the district. What detailed examination has done, of course, has been to reveal the accuracy with which the contact can be placed in different parts of the district, and to show up, in consequence, areas in which further work might reasonably be expected to disclose hitherto unknown or unsuspected ore. Viewed in this light, the proportion of the norite contact which is covered by substantial quantities of overburden is astonishingly large.

Jan 1, 1939

Agenda ? Introduction ? Inmet?s Operations and Closed Properties ? Inmet?s SECA Philosophy ? Inmet?s SECA Framework ? The Business Case for TSM ? Inmet?s TSM Reporting ? Inmet?s 2004 TSM Performance ? Opportunities for Improvement ? What Have We Learned From The TSM Process So Far? ? Summary Introduction ? Inmet has evolved into a strong TSM supporter ? Inmet is confident that TSM can be successfully and cost effectively implemented by smaller companies ? Inmet?s reporting on economic, environmental and social performance was raised significantly in our 2003 Annual Report ? a signal our commitment to good performance and improvement in these areas ? Our 2004 Annual Report has been further enhanced with the inclusion of our TSM performance

Apr 1, 2005

By Hani Henein

Most metals and alloys processed undergo a solidification processing step. Increasingly, there is a growing number of solidification processing routes that involve rapid solidification of the alloy. These include strip casting, high pressure die casting, 3D printing, and atomization for the production of powders or spray formed parts. By contrast, there are few experimental techniques developed to study the solidification path of alloys during rapid solidification. Amongst these laser melting and solidification, Electromagnetic Levitation (EML) and Impulse Atomization (IA) are the most prominent. Of relevance is the formulation of the solidification path of an alloy and the resultant identification and quantification of metastable phases and their relationship to processing conditions. This typically involves the understanding of the interplay between undercooling and cooling rate for the various phases that form. This presentation will outline some of the methodologies developed to quantify phase fractions and their solidification path as a function of processing conditions using EML and IA.

Jan 1, 2016

By Douglas E. Wolfe, Jogender Singh, Robert Miller, Dong-Ming Zhu, Jeff Eldridge

This paper discusses microstructural changes produced by two novel approaches using electron beam physical vapor deposition (EB-PVD) in which periodic strain fields/microporosity was incorporated within the large columnar grains of Zr02- 8wt.%Y2O3 (8YSZ). The traditional columnar microstructure of partially stabilized zirconia has been slightly modified to produce a lower thermal conductive thermal barrier coating (TBC) by periodically interrupting the condensing vapor resulting in microstructural modifications with diffuse or sharp interfaces and morphological changes on the sub-micron scale without changing the composition of the TBC. These microstructural modifications resulted in a 20-30% reduction in the thermal conductivity, 28-56% increase in hemispherical reflectance, improved oxidation cyclic life (over 100%), and better strain tolerance as compared to standard ZrO2-8wt.%Y2O3 deposited on platinum-nickel-aluminide and CoNiCrA1Y bond-coated MAR-M-247 test samples. The TBC with tailored microstructures were examined by various techniques including scanning electron microscopy (SEM), x-ray diffraction (XRD), steady-state laser heat flux technique, and hemispherical reflectance.

Jan 1, 2004

By M. Solomon

Giant, sediment-hosted lead-zinc deposits in northern Australia fonned during development of Mid-Proterozoic extensional basins that overlie Lower Proterozoic basement. The basement in the Mount Isa area, exposed by folding and faulting, contains fractionated, high-heat-producing granites. These granites generate heat at a rate of about 6",Wm-3, probably sufficient to fonn giant lead-zinc deposits either by (a) driving episodic convection of saline basement and basin fluids for periods of IOS to 106 years at temperatures of about 230°C, or (b) heating basin fluids moving under the influence of topographic relief or fault movement. The presence or absence of such granites may form a vital component of the genetic model. Ore-fonning fluid flow was probably initiated by continent-scale, extensional basin fracturing.

Jan 1, 1992

By BARRY BANNATYNE

Gypsum in Manitoba is quarried from the Jurassic Amaranth Formation a1 Gypsumville and Harcus; it has been mined near Amaranth and Silver Plains. At Gypsumville, gypsum is carbonate- free but has thin clay laminae between gypsum layers; the rock is folded in places, and some anhydrite is present. At Harcus, gypsum contains scattered dolomite, both as patches in a penemosaic pattern and as thin layers; small chalcedonic concretions also can be found. The quarry at Harcus was opened late in 1978 and currently produces about 100,000 tonnes annually. The two inactive mines near Amaranth operated from 1932 lo 1963 and from 1967 to 1970, and contain a central anhydrite layer. The mine near Silver Plains was flooded from an underlying artesian aquifer in 1975 and has not been reopened. Manitoba gypsum is used in cemem plants in Mani1oba and Saskatchewan and in wallboard plants in the three Prairie Provinces.

Jan 1, 1984

By E. Poiate, P. A. L. P. Firme, D. Roehl, M. A. Carrion, A. M. Costa

Drilling high-pressure/high-temperature wells in salt rock formations is still a challenge for the energy industry. Creep and solubility is part of the salt rock physical-chemical behaviour, which must be considered in the design of the wells. The stress redistribution caused by drilling, in addition to thermallyactivated processes, triggers creep deformation, leading to borehole closure and the imposition of loads on the casing. The drilling fluid is designed by computer modeling in order to control the creep strain rate to a limit which allows the drilling operations and the casing setting. Depending upon the composition of the drilling fluid, chemical reactions on the salt wall may occur, especially in case of water-based fluids in highly soluble salt rocks. In those cases, cavities by dissolution (washouts) can be generated and the casing column remains uncovered by the cementation and laterally unconfined along the cavity length. This scenario is propitious to the loss of integrity of the casing due to phenomena such as plastic collapse, buckling and non-uniform loading on the casing provoked by the closure of salt formation around it. The casing should remain intact during the wellbore life-time. In this work, a section of a typical well crossing salt formation composed by halite and carnallite is considered. An idealized-cylindrical washout cavity inside a highly soluble salt layer is assumed. The purpose here is to evaluate the effect of the dimensions of the cavity on the integrity of the casing. Several typical diameters and lengths of the cavity are adopted. Numerical analyses are carried out with an in-house finite-element system composed by the pre-processor MTOOL 3D®, the simulator ANVEC 3D® and the post-processor POS 3D®. Salt rocks are modeled as visco-elastic materials. Creep is simulated by the Double Mechanism Creep Law, widely employed in Brazilian salt rock mechanics research. Cement and casing (steel) are modeled as elasto-plastic materials described by the Mohr-Coulomb and the von Mises criteria, respectively. Casing integrity is evaluated with respect to vertical and horizontal displacements. Vertical displacements imposed to the casing can provoke the failure of the column by plastic collapse or by buckling. Besides that, horizontal displacements of salt due to creep closure shall lead to the undesirable contact with the casing. Failure envelopes based on displacements are generated. The results of the simulations have shown that the casing failure by plastic collapse occurs preferentially in short columns, as well as buckling occurs in long and slender columns. The occurrence of both failure modes is more frequent in large-diameter cavities. Additionally, failure caused by contact between salt and casing occurs preferentially in short-diameter cavities.

Jan 1, 2015

By M. Solomon

Abstract -Giant, sediment-hosted lead-zinc deposits in northern Australia formed during development of Mid-Proterozoic extensional basins that overlie Lower Proterozoic basement. The basement in the Mount Isa area, exposed by folding and faulting, contains fractionated, high-heat-producing granites. These granites generate heat at a rate of about 6 ?Wm-3, probably sufficient to form giant lead-zinc deposits either by (a) driving episodic convection of saline basement and basin fluids for periods of 105 to 106 years at temperatures of about 230°C, or (b) heating basin fluids moving under the influence of topographic relief or fault movement. The presence or absence of such granites may form a vital component of the genetic model. Ore-forming fluid flow was probably initiated by continent-scale, extensional basin fracturing.

Jan 1, 1992