Search Documents

By P. S. Daly

"The purpose of this paper is to describe the types of instrumentation used at Sherritt Gordon's Ruttan Mine to monitor the"" effects of mining. The aim of the monitoring program is to establish parameters to achieve a maximum ore recovery with minimum dilut ion in a safe environment.The copper-zinc Ruttan Mine is in northwestern Manitoba, approximately 760 km from Winnipeg (Fig . I) . Production commenced in 1973 from the open pit at the rate of 10,000 tons per day. Pit bottom lies 58 metres above the first mine level. Underground development has overlapped with open-pit mining throughout. The open pit was phased out in the latter part of 1980.Underground production began in early 1979. The mining method employed in the first lift is sub-level blasthole open stoping with delayed hydraulic filling. Large-diameter (6.5-in.) holes are being drilled in the crop stope area and are also planned for some other areas for vertical retreat mining into a slot. GeologyThe orebody consists of numerous sulphide lenses of variable size, geometry and geology . The lenses occur within volcanoclastic host rocks which exhibit a strong variability in intensity and type of alteration and structural characteristics. Stope design and sequencing were based on these complex geological factors."

Jan 1, 1981

By T. Gonzales, M. Maleki, M. Caçador, B. Climenhaga, H. Ghorbani

The campaign life of furnaces in the copper making industry is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper monitoring and assessment of the existing conditions and safe remaining life of the vessels and their refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a typical fitness-for-service assessment of a rotary vessel shell in order to extend the campaign life of copper making furnaces and enhance safety. The furnace refractory management system involves a comprehensive audit and monitoring program which has been successfully applied to several copper flash smelting furnaces over the past 15 years. The fitness for service assessment provides a methodology to estimate the remaining life of the steel components by evaluating the existing damage and future damage rate based on the historical survey data. The above practices can provide the operator with cost savings by extending the vessel campaign life in lieu of implementing more rigorous refractory lining and shell audits. INTRODUCTION Primary copper smelting is generally divided into two categories of flash smelting and open bath smelting. There are many different types of vessels that can be used to convert the copper concentrate to blister copper including, flash, Mitsubishi process, TSL (ISA/Ausmelt), SKS Bottom Blowing, Anode and Teniente/Noranda furnaces, reactors, and Peirce Smith converters. Each vessel has its own complex and intense environment which requires careful refractory and steel design to withstand the severe thermomechanical and thermochemical attacks within its campaign life. The campaign life of furnaces is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper assessment of the existing conditions and safe remaining life of the vessels and/or refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a fitness-for- service assessment methodology to estimate the remaining campaign life of copper making furnaces resulting in cost savings and enhanced safety of the operating vessels.

Jan 1, 2019

By Patrice Nadeau, Yuejun Zhang, Dan Chen, Liming Huang, Claude Gagnon

"The traditional Denver flotation cell is generally suitable to process material ranging approximately from 5 µm to 300 µm. For floating over 300 µm material, its efficiency is significantly getting lower mainly due to the difficulty to suspend coarse particles uniformly, which decreases the chances of particles to attach to bubbles and increases the chances of detachment.RTFT (Rio Tinto Fer et Titane) owns one of the world’s largest hemo-ilmenite deposits. Considering the whole processing technology, the ore is only crushed to -1180 µm. The crushed ore contains about 0.32% S and most of the sulfur is removed by rotary kilns in the ore preparation plant. In order to achieve a similar S reduction, without emitting SO2 into the air, an alternative technology by flotation was pursued.Laboratory and pilot scale-up tests showed that traditional Denver flotation cell could perfectly remove the sulfur from the material sizing 0-300 µm. For the coarser particle sizes, two different models of equipment were tested to improve flotation efficiency: HF (HydroFloat Separator) from Eriez and CLF from BGRIMM (Beijing General Research Institute of Mining and Metallurgy), China. The D6” HF, which is a device that combines flotation and gravity separation, demonstrated its ability to recover those very coarse particles. As compared to the Denver flotation cell, the modified 25 L CLF coarse particle flotation cell achieved better results at higher pulp solids percentage and with a shorter flowsheet."

Jan 1, 2016

By N. Haghdadi, D. M. Maijer, A. B. Phillion

B206 is a recently-developed high-strength Al-Cu casting alloy with reduced Ti and Fe, as compared to the well-known AA 206 alloy, for improved hot tearing resistance. In the current study, the solidification kinetics of this alloy as a function of cooling rate from 1 to 15 K/min were studied using differential scanning calorimetry (DSC) and microscopy. Specifically, the evolution in fraction solid, grain size, and secondary dendrite arm spacing have been characterized. The DSC results show the occurrence of three peaks during cooling from the liquid state, which are related to the formation of primary aluminum, a pre-eutectic intermetallic, and the eutectic phases. Thermal analysis also indicates that while the liquidus temperature is not sensitive to the cooling rate, the temperatures at which the pre-eutectic and eutectic phases form are strongly coupled to the rate of heat extraction. A decrease in the latter temperatures was observed when the rate of solidification was increased, leading to a lengthening of the freezing range of the primary phase. The results will be useful for improving B206 casting processes, specifically through modification of mould cooling conditions.

Jan 1, 2014

By Nick Vagenas

"Loading and transportation are important activities of the mining process. Automation of these activities in underground hard rock mining has been discussed for a long time. This paper deals with the performance evaluation of a prototype automatic Load-Haul-Dump (LHD) vehicle (a 7-ton GHH LF LHD model) operating in Zinkgruvan mine, Sweden. The purpose of the data analysis is to evaluate the operational and maintenance characteristics of the automatic LHD system in the mine. Graphical and numerical methods have been used for the statistical analysis of the data. IntroductionDuring the past years, the idea of integrated automation and tele-operation on Load-Haul-Dump (LHD) machines (Fig. 1) has attracted considerable interest in the Swedish mining industry. This is mainly due to the demand for improvement in the working environment and due to the rapid development of economic and reliable microprocessors for mining vehicles. Several advantages can be foreseen with the application of a Remote-controlled/Automatic LHD (RAL) system in underground mining. Some of them are (1)':• better utilization of working hours;• less interruption in production at shift changes;• better operational control of a fleet of vehicles;• improved safety; and• one operator may be able to operate more than one vehicle simultaneously."

Jan 1, 1993

By R. Ichimura

This paper summarizes the results of a five-year project, which aimed at improving the current method to process the arsenic-bearing smelter dust of El Teniente. This project, which was started in 2001, was carried out jointly by JOGMEC (Japan Oil, Gas and Metals National Corporation) and CIMM (Centro de Investigación Minera y Metalurgica, Chile), and was financially supported by the Japanese and the Chilean governments. In the new process, the smelter dust is leached with sulfuric acid to dissolve arsenic, which is subsequently precipitated as crystalline ferric arsenate (scorodite) at ambient pressure by controlling the crystallization and crystal growing stage. As a result, a stable form of ferric arsenate is obtained, which passes the U.S. E.P.A. TCLP limit of 5 mg/L As. Copper and zinc are subsequently recovered from the arsenic-free solution. The copper product can be fed into the main copper production circuit at the Las Ventanas Smelter and Refinery, whereas zinc is recovered as a marketable product. A demonstration plant was installed and operated at CODELCO's Las Ventanas Smelter and Refinery. The basic and detailed engineering design was prepared by Mitsui Mining and Smelting Co. Ltd (MMS) on the basis of a joint study done by JOGMEC, CIMM and CODELCO's Las Ventanas Division.

Jan 1, 2007

By K. H. March

In the present very highly competitive condition of the bituminous coal business, it is becoming increasingly apparent that coal mines which do not lend themselves to efficient mechanization cannot long survive. It would seem that those mining operations best fitted to survive the struggle for existence are burdened with the considerable capital and maintenance cast of carefully selected mechanical and electrical mining equipment. The ever changing conditions of coal mine operations require equipment which is adaptable to a variety of uses; and investigation of the mechanical and electrical equipment in most mines will show that the operating duty of much of this equipment is considerably different from that duty for which it was originally selected. And it would appear that one of the essential qualifications for a successful mine management is a marked ability to get satisfactory operating results from equipment which has been transferred from some other operation, rebuilt, rearranged, or in some way adapted to the job at hand. As a striking example of such mechanical ingenuity, many of us recall that the first longwall jigging conveyor used in Nova Scotia was built in Sydney Mines from odds and ends in the scrap pile at a total cost of less than $50.

Jan 1, 1930

By Robert Boutilier

For more information on what the social licence means, see the following: Joyce, S. and Thomson, I. 2000. Earning a social licence to operate: Social acceptability and resource development in Latin America. The Canadian Mining and Metallurgical Bulletin, 93(1037) Nelson, J. and Scoble, M. 2006. Social License to Operate: Issues of Situational Analysis and Process. Vancouver, BC: Department of Mining Engineering, University of British Colombia. Thomson, I. and Boutilier, R.G. 2010. The Social License to Operate In P.Darling, (Ed.), SME Mining Engineering Handbook: Littleton, CO: Society for Mining, Metallurgy and Exploration. Much of what has been written and said about the social license to operate focuses on what the company has to do or not do. But the social license is a two-sided relationship. We also need to look at what the community has to do, or not do, in order to be capable of issuing a social license that is meaningful.

May 1, 2010

SOME months ago a Committee on Deep-level Mining was appointed [by the Government of the Union of South Africa] to consider the possibility of gold mining being carried on at a depth below 8,500 feet. The Committee consisted of Sir Robert Kotze (Chairman) , Mr. H. S. H. Donald (Government Mining Engineer), and Mr. H. R. Hill. The Committee has now made a report which was tabled in the House of Assembly on March 1st. The Committee reported that the tonnage of ore locked up in the deep level areas of the Central Witwatersrand is enormous, and in the 30 miles between Roodepoort and the East Rand Proprietory Mines has a value of about £200,000,000. The Committee says that, with good ventilation, the present system of wet mining, possibly with some modification and with the aid of refrigeration, may be carried to 10,000 feet, but that greater depths will require the adoption of dry mining. "A vigorous campaign of practical experiment into the possibility of dry mining should be initiated, and the Committee recommends to the Government the appointment of a committee of experts, consisting of representatives of the mining industry, the Mines Department, and the medical profession, with the Government Mining Engineer as chairman. The Committee suggests the provision of £30,000 for the first year for the investigations and experiments contemplated, which could best be carried out by an organization which might be styled 'The Rand Mining Research Institute' and constituted somewhat on the Jines of the South African Institute for Medical Research" . The Committee suggests that this committee of experts should arrange for experiments to be made with dry mining in one of the deepest mines, and investigate ventilation, refrigeration, support of workings, and the physiological problems connected with mining. "We emphasize the necessity of treating this whole question as one of importance and urgency. The investigations should be prosecuted with the utmost vigour and should not be delayed at any time for want of funds or for any other reason. If they are not done thoroughly and quickly, the whole scheme might just as well be left severely alone.

Jan 1, 1945

By Todd S. Harris

"IntroductionThe western region of North America has long been considered a dynamic market supporting such diversified industries as lumber, agriculture, cement, and electronics. In recent years however, the region has also been the focus of a great deal of activity in the extender and filler mineral s business from companies seeking to position themselves to take advantage of the large demand for these materials both here and abroad.Extender and Filler MineralsExtender and filler mineral s include 15different products used in numerous end uses. The nine most important extenders and fillers are listed in Table I. These products range in price from under $50 a ton to over $4,000 a ton and basically represent the following three different types of minerals:Particulate products-Calcium carbonate; Kaolin; Silica.Platy minerals-Talc (Montana, Canada); Mica.Fibrous minerals-Talc (California, Eastern U.S .A.);Wollastonite.What distinguishes these products from other industrial minerals? For one thing, an important feature of extender and filler minerals is that they are used primarily in such consumer non-durable good s as paper, paint, plastics, sealants, and rubber which traditionally do not react as violently to swings in the economic cycle. In addition, these minerals are sold principally on key physical properties, usually brightness, particle size and shape, oil absorption, and hardness. As part of the physical minerals segment of industrial minerals, extenders and fillers are traditionally the most stable group and typically the most profitable. Studies by C.H. Kline over the past decade on extender and filler minerals has revealed historic average profitability (expressed as a percentage on sales) nearly double that of most other industrial mineral s.The demand for these minerals in the western region (Fig. 1), closely follow s the areas of greatest population concentration. These markets include pulp and paper, mainly in the Pacific Northwest, and paint, around Los Angeles and San Fran cisco. Other significant markets for extender and filler minerals in western North America include joint cements, carpet backing, and plastics, mainly PVC pipe."

Jan 1, 1986

By N. Saracoglu, R. H. Wallis, J. E. Betz, F. L. Jagodits, B. R. Krause

"Geophysical test surveys were conducted with various methods (EM, lP, gravity and magnetic) over the McClean uranium deposits of the Canadian Oxy- lnco Joint Venture. The result s were assessed to judge the contribution each method might make toward further discoveries of graphite-associated uranium occurrences.The best drill targets have proven to be discontinuities in graphitic conductors and locations where the tatter are intersected by fracture zones in the Athabasca. The tests demonstrated that the preferred combination of geophysical survey s is horizontal loop EM to locate graphitic conductors in the basement and VLF-EM to locate the fractures.IntroductionThe discoveries of the McClean North and South uranium deposit s (Fig. 1) are essentially geophysical successes resulting from drilling MaxMin delineations of INPUT airborne electromagnetic responses (Saracoglu et al., 1983). After the initial discovery in 1979, various geophysical methods, techniques and instruments were employed to test their effectiveness in this environment and to guide exploration for other deposit s of a similar nature in the remainder of the 260 km2 property.The McClean uranium deposits lie below 150 m to 180 m of overburden and Athabasca Group. Radioactive signatures might be expected; however, the Athabasca Group acts as a barrier to radioactive emanations. Fortunately, the uranium mineralization is associated with graphite in the crystalline basement. Prior drilling of ground electromagnetic anomalies confirmed that EM surveys could locate and out line basement graphitic conductors. However, as there were many anomalies, most of which could not reasonably be expected to be associated with uranium , there was need to identify additional parameters, related to mineralization, which could be detected geophysically and used to narrow the search."

Jan 1, 1986

By Steven Chung

Decision Network Modelling in a mining operation represents a complex process environment that is inherently more variable than a processing plant or factory. The uncertain availability of loading locations, haulage paths, loading and hauling equipment, along with inconsistent operator behaviour, cause a relatively large number of upset events that must be recognized, communicated and dealt with by the appropriate management authority. Traditional process maps that represent a deterministic model of the mining process can quickly break down in the face of such a volatile environment. An alternate modelling strategy, composed of decision networks, focuses on the interactions between goal-oriented entities and their environment, allowing system integrators to explicitly determine the information to be exchanged while providing feedback mechanisms that improve system flexibility and decision quality. This ensures a consistent framework for incrementally increasing system automation.

May 1, 2010

By S. McCarthy, K. E. Waters, A. Jordens

The beneficiation of rare earth (RE) element bearing minerals has become an active area of research as applications for these elements grow while the supply to non-Chinese consumers is restricted by export quotas. One of the most interesting beneficiation techniques for RE minerals is froth flotation as their unique chemistry suggests that collectors with a specific affinity for RE cations should be able to selectively recover these minerals. Existing literature, focusing mainly on bastnäsite flotation, identifies hydroxamic acids as excellent collectors for RE minerals. The high stability of hydroxamate-RE cation complexes is the explanation most often offered for the observed selectivity of these reagents in bastnäsite flotation however some research has also suggested that mineral solubility plays a crucial role in the success of hydroxamic acid flotation of RE minerals. This work investigates the interaction of allanite, a relatively insoluble RE-silicate mineral, with benzohydroxamic acid using zeta potential measurements and microflotation. The effects of Fe(III) and Fe(II) ions as potential activating ions (cations that form stable hydroxamate complexes) on benzohydroxamic adsorption to the allanite surface are investigated as a potential solution to promote hydroxamic acid adsorption. The results indicate that the optimum conditions for separation of allanite from quartz occur at pH 4 using FeCl2 as an activator for benzohydroxamic acid adsorption.

Jan 1, 2014

By D. Sbarbaro

In many modem concentrators the use of supervisory systems in their grinding circuits has meant more consistent operations and increases in capacity. These systems rely on a series of specific algorithms that uses different pieces of information and drives actions over the process. One of these algorithms is the ball mill overload detection, which plays an important role in any supervisory strategy designed to maximize ore feed rate in wet grinding circuits. This paper introduces different overload detection algorithms, and compares them in terms of the time taken to detect the overload condition. This comparative analysis is based on highly noisy power draw measurements obtained in an industrial plant.

Jan 1, 2007

By Jian Deng, Haitian Sun, Zengqian Hou, Shuhe Song

"Abstract - Volcanogenic massive sulfide (VMS) deposits, an important base-metal deposit type in China, occur widely in submarine volcanic districts of variable magmatic affinities. These VMS deposits range in age from Archean to Mesozoic, but most are in Proterozoic and Paleozoic sequences. More than 60% of VMS deposits formed in the Paleozoic, the most important metallogenic eon. Three important Paleozoic VMS-metallogenic provinces include Northern Qilian, Sanjiang and Altai provinces. The Proterozoic constitutes the next important era, but with no VMS deposits in the middle Proterozoic. VMS deposits associated with the Proterozoic volcanic rocks occur around the Yangtze Platform and in the western Kunlun-Qinling. The Triassic is third in importance, with VMS deposits concentrated in the Sanjiang Tethys. The Archean has only one VMS deposit, on the northern margin of the Sino-Korea Platform.Five distinct compositional classes of Chinese VMS deposits have been distinguished: Cu, Cu- Zn (or Zn-Cu), Cu-Fe, Zn-Pb-Cu, and Pb-Zn (-Cu). The Cu, Cu-Co, and Cu-Zn types of deposits occur sporadically from the Archean to Paleozoic, and are closely associated with mafic and ultramafic volcanic sequences. The Zn-Pb-Cu and some Cu-Zn type deposits are restricted to the Paleozoic and Triassic, and are hosted by calc-alkaline felsic rocks in bimodal basalt-rhyolite sequences, whereas Cu-Fe and Pb-Zn type (except for the Laochang deposit) deposits are restricted to the Proterozoic and occur in calc-alkaline volcanic sequences. As large quantities of marine mafic volcanic rocks were deposited in western China, Cu and Cu-Zn deposits are major types of Chinese VMS deposits.Chinese VMS deposits formed in a wide range of paleo-tectonic settings and depositional environments, such as island-arcs, rifts, aulacogens, and ocean ridge hot spots. Among these, the rift and back-arc environments are the most important, containing about 60% of Chinese VMS deposits. Aulacogens are a subordinate environment where most of the Proterozoic VMS deposits formed. The oceanic ridge and hot-spot systems are common in the tectono-magmatic domains in China, but contain only a few small Cu and Cu-Zn type VMS deposits.The Chinese VMS deposits have usually been influenced by both deformation and metamorphism to various degrees, resulting in changes in the shape and metal distribution. Seven representative deposit styles have been recognized: sheets, sheet plus strata-bound stringer, cyclically zoned deposits, mounds, mound-like deposits, strata-bound stringer-disseminated, and stockwork-disseminated deposits. The formation of these various styles of deposits is controlled by several key factors, such as lithology and permeability of the host rocks, focused or unfocused discharge, temperature and chemical composition (e.g., salinity) of hydrothermal fluids, as well as depth of seawater."

Jan 1, 1999

"The gravimetric dust sampler is one of the tools now available to the industrial hygienists for determining the worker 's exposure to the numerous types of particulate matter that may be present in the workplace. The paper ' reviews the different sampling trains that can be used for the two major criteria for respirable dust and some of the sources of error in this dust assessment technique.IntroductionIt may be stated simply that the measurement of airborne dust in the working environment is done for one or two reasons: namely, for engineering control purposes and! or to evaluate the potential for toxicological insult arising from the inhalation of dust particles.This paper reviews the progress made in the development of dust-assessing instruments, particularly the gravimetric types designed to meet British and U.S. dust criteria , and discusses the limitations in their use for this purpose."

Jan 1, 1981

"INTRODUCTIONThe Department of Energy, Mines and Resources has recently developed two automatic controls for use in the cyanidation circuits of Canadian gold mills. These controls are the alkalinity probe and the Continuous Cyanide Titrator both of which are discussed in the paper ""Instrumentation in the Cyanide Process"".(1)In May 1966 these process controls and associated recording equipment were installed in the Bralorne mill by two Scientific Officers from the Department. The object was to determine if the equipment was amenable and applicable to this particular circuit. The purpose of this paper is to discuss the performance of the equipment over a test period of 4 months.CONCLUSIONSThe results of test work to date indicates that both the Conductivity Probe and the Continuous Cyanide Titrator would be an as set to the operation of the Bralorne mill.The conclusions are generalized as follows:-(1) At a milling rate of 100, 000 tons per year the expected reductionin reagent consumption would give a direct saving of 37, 660 lbs of lime@$0.030 per lb and 15, 790 lbs of sodium cyanide@ $0.175 per lb. Such cost savings would pay for the equipment and installation costs within a 30 month period"

Jan 1, 1967

By S McQuitty

The metallurgical treatment of Falconbridge ore re-quires an extremely fine grind of the pyrrhotite portion ? for maximum liberation and recovery of nickel. This paper describes the operation of a grate discharge pebble mill in closed circuit with cyclones regrinding 25 to 30 tons per hour of sulphides to approximately 90 per cent minus 325 mesh. The consumption of the screened ore grinding medium is of the order of 2.5 pounds per kw.-hour, or less than 1 per cent of the tonnage of re-ground sulphides. IN RECENT years, there has been a considerable interest in pebble grinding in the uranium industry, and a number of installations have appeared. However, the use of sulphide ore pebbles as a grinding medium has so far been relatively limited. There has also been some question as to their suitability for the very fine grinding of sulphide concentrates. This paper describes the preliminary results of a commercial operation involving the

Jan 1, 1964

By I Wilkomirsky, F. Parada, R. Parra, E. Balladares

"The neutral roasting of As bearing copper concentrates is confirmed well established and promising option for the treatment of this type of complex concentrate. The AS elimination by volatilization allows subsequent treatment of the calcines produced in a conventional pyrometallurgical process, by blending this product with standard concentrates.Several tests were performed using the fluidized bed pilot plant at the University of Concepción with different types of concentrates. Calcines, fines from two hot cyclones and flue dust from the ESP were collected. These materials were characterized using QEMSCAN® and the results used for the development of a mass and energy balance which took into consideration the specific chemical transformations that occurred in the reactor.A physico-chemical/kinetic model is proposed to explain the formation of bornite, chalcopyrite and magnetite. The mechanism involves solid-gas reactions between chalcocite, pyrrhotite and gaseous sulfur that without the mineralogical characterization would not have been possible to propose"

Jan 1, 2014

By G. Mucsi, J. Faitli, K. Bohács

"The authors developed an online tube rheometer to supplement a Netzsch MiniCer (Netzsch GmbH, Germany) stirred media mill in order to monitor online the rheological characteristics of the suspension and therefore the result of grinding during the process. Previously it was demonstrated that the above measuring system was working appropriately based on the preliminary tests. The product related stress model was applied for the evaluation of the grinding results. It was found that the suspension concentration and the change of the material properties during grinding, consequently the rheology strongly affects the grinding result, i.e. specific surface area, median particle size as well as specific grinding energy. The tested model limestone – water suspensions behaved Newtonian initially, then after a given grinding time their properties had changed and they become Bingham plastic. INTRODUCTIONStirred media milling now is a common practice to produce fine and ultrafine granular materials for different purposes. With an increasing demand of ultrafine powders for industries (Kwade, 1999), wet and dry ultrafine grinding has been increasingly used in various fields, such as minerals (Mucsi, Rácz, & Mádai, 2013)(Rácz, 2014), ceramic materials (Becker & Schwedes, 1999), pigments (Ohenoja, Illikainen, & Niinimäki, 2013), chemical products (Baláž et al., 2013), microorganisms (Kwade & Schwedes, 2002) and pharmaceutics (Afolabi, Akinlabi, & Bilgili, 2014). It is well known that suspension rheology affects the wet comminution of materials (He, Wang, & Forssberg, 2006a). The rheological behaviour of the suspension containing the ground particles might indicate the level of interparticle interaction or aggregation and therefore it is an important variable factor of the process control (Muster & Prestidge, 1995). The influence of the rheological behaviour of mineral suspensions on their grindability has attracted more and more interests and attention, especially on ultrafine grinding performance (He, Wang, & Forssberg, 2006b) (Bernhardt et al., 1999). However, there are still many issues concerning the machine and the process for the different applications. When grinding is effective and the particle size range decreases significantly, the circulating suspension is becoming typically non-Newtonian. The changed rheological behaviour and the increasing rheological material parameters can negatively affect the grinding efficiency; therefore it is an important issue. Ultrafine stirred media milling as well as solid-liquid two phase flow have been studied for a long time at the Institute of Raw Materials Preparation and Environmental Processing of the University of Miskolc. Regarding ultrafine grinding the research is focusing on the description of materials’ grindability (energetic aspects) both in wet and dry circumstances (Mucsi et al., 2013; Rácz, 2014). Concerning rheology, the three measuring pipes tube rheometer was developed decades ago (Faitli & Gombköto, 2015). So far many different solid materials from all over the world had been tested in this rheometer (Faitli & Gombköto, 2015). Main aim of these tests was to gain basic data for large scale hydraulic transport applications. Among the many stirred media mills there is a Netzsch MiniCer mill at the Institute. It was reasonable to combine the two fields together, and the goal of the research presented in this paper is to develop an online tube rheometer for the Netzsch mill and to carry out grinding and rheological testing simultaneously."

Jan 1, 2016