Search Documents

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters – usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

By Rainer Süss

An investigation was carried out by Mintek to investigate the influence of a range of alloying additions (vanadium, cobalt, zirconium, antimony and germanium) on the formability and hardenability of alloys with gold content >90 wt%. This paper reports on the hardening mechanisms that can be utilised to increase the hardness of gold (>90 wt% Au) by conventional alloying, as well as the hardening effect obtained by alloying with specific elements. Preparation methods for the alloys are described, which include the steps of melting, annealing, quenching, cold working and age hardening. Focus is given specifically on alloys that were developed at Mintek with a gold content >90 wt%, which are not only harder, but exhibit good resistance to tarnishing and corrosion.

Oct 1, 2003

By O. Guyot, A. Broussaud, M. Revalor, G. Legrand, D. Kok, E. Roux

"The paper describes the advanced grinding control system implemented at Newmont Ahafo gold mine, Ghana in 2009 and 2010. It shows how the different components of the Advanced Process Control (APC) system cooperate for increasing plant performance.The SABC circuit processes hard rock from different pits mixed with a variable proportion of oxides. The control strategy is designed to address specific disturbances, including start/stops of pebble crushers, unavailability of oxides, changes in rock size distribution resulting from segregation in the stockpile, and changes in ore type and hardness.The system consists of an expert system per se with extensive use of fuzzy logic, supplemented by an online dynamic model of the process used as a soft sensor, a VisioRock™ rock size measurement system over SAG mill feed before addition of recycled pebbles, and an AudioMill™ system to analyze the SAG mill sound and detect impacts on liners. All these components are embedded in the same OCS© software platform, which, among other benefits, makes it easy to support the entire system remotely. The paper details the physical constraints and the variables that are manipulated. It describes the control strategy and the contribution of each component of the system. It also describes the project implementation and the performance of the system. In addition to a strong involvement and support of management, the very good acceptance of the operators has been facilitated by the remote access system that made it possible to immediately modify the system each time it was needed during the baby sitting phase.The system made it possible to increase gold production significantly through increases in tonnage and recovery thanks to a better control of the grind size through a stabilization of the secondary ball milling circuit and an improvement of the operating conditions of the classifying cyclones."

Jan 1, 2012

By Lo-Sun Jen

Introduction ? Canada is one of the largest miners and explorers in the world and is a world leader in the production and export of many key mineral commodities ? Canada has a stable political regime and a competitive investment and business climate ? Canada is endowed with mineral resources, advanced technology and management know-how ? Canadian stock exchanges are the world?s leading centres for raising equity financing for exploration and mining projects anywhere on the globe As with some other countries, Canada has experienced a recent decline in major mining developments

May 1, 2002

By Michael K. Watkeys, Jacobus E. Potgieter, E. Guy Charlesworth, Carl R. Anhaeusser, Roger L. Gibson, Alexander F. M. Kisters

Intrusive features of cupriferous noritoids from the deeply eroded Proterozoic granite-gneiss terrane of the Okiep Copper District in South Africa illustrate the emplacement of basic magmas into a mid- to lower-erustal environment. The small, easterly trending intermediate to basic intrusions of the so-called Koperberg Suite display a wide variety of geometries, occurrence and emplacement modes, including dike-, sill- and plug-like bodies. Coeval granulite-facies metamorphism, partial melting and ductile deformation of country rock gneisses during intrusion of the basic magmas led to emplacement and dilation processes of the intrusions which differ significantly from those described for dikes and sills at shallow crustal levels. Regional tectonic stresses are largely negligible due to very low differential stress [( )] during deformation and intrusion, which permits emplacement at high angles to the principal compressive stress and which follows favorably inclined structural anisotropies. Dilation of the basic intrusions is largely determined by compositional differences of host rocks and occurs by thermal erosion, i.e., assimilation of wall rock gneisses. Low length-to-width ratios of basic to ultrabasic dikes and predominantly diapir-like outlines of mesocratic bodies are indicative of low viscosity contrasts between the mafic magmas and high-grade metamorphic host-rock gneisses. Buoyancy-controlled ascent of the basic to intermediate intrusions is expressed by a broad compositional zoning of basic bodies with respect to the granite-gneiss stratigraphy. Various intrusion modes within the stratigraphic column of the granite-gneiss sequence reflect a lithological and structural stratification of the seemingly homogeneous granite-gneiss terrane.

Jan 1, 1994

By Robert B. Parsons

"It is generally acknowledged that Canadian and foreign-based mining companies are spending relatively fewer dollars in Canada and more dollars abroad than was the case not many years ago. It is common to see the Canadian tax system being fingered as one of the causes in this shift in direction. However, if one takes the time to peel away the surface of our tax system, and to probe a little deeper into its substance, it will be found that the Canadian taxation of mining is generally quite competitive. IntroductionCross-border shopping in the mining industry? - Absolutely! Economics 100 teaches that dollars are votes in the capitalist system, and mining companies are going to cast their limited number of votes where they can achieve the highest return at the least risk. The Canadian consumer knows that taxes are a major factor in cross-border shopping, and mining company executives know that the same tenet holds true in their industry. Unfortunately, mining operations are subject to such a bewildering array of tax rules that making an intelligent decision is not always an easy matter.Statutory Tax RatesConsider, for example, the ""statutory"" tax rates shown in Table 1. (Statutory tax rate in this table refers to the simple sum of federal and provincial tax rates on profits as specified in the tax legislation.) Looking only at the total statutory tax rates (such as 66070 for Manitoba) , one might quickly observe that the Canadian mining industry is subject to a truly onerous tax regime, especially as compared to the United States where statutory tax rates can be in the 34% range."

Jan 1, 1992

By W. T. Boyes, J. M. Harrison

"Squall Lake Gold Mines, Limited, owns a group of claims at Squall lake, northern Manitoba, about 75 miles east of Flin Flon and 3 to 4 miles north of the Nor-Acme mine at Snow lake. Gold mineralization was discovered in this locality several years prior to 1944, but it was only in that year that a comprehensive examination of the occurrences was begun. Development work to the end of 1946 has been encouraging and the deposits show interesting relations to rock structure.GEOLOGICAL SETTINGThe gold occurs in a sill of biotite-hornblende diorite at or near its contact with gneisses derived from arkosic sediments . In detail, the contact between the diorite and the arkose to the southeast of it is irregular, with interfingering of the two rock types. On the northwest side of the sill, between it and Squall lake, the rock is staurolite schist (see accompanying sketch-map).Several mineralized shear zones are known, of which those shown are the most important. Within the zones, the diorite is silicified and somewhat carbonatized. Fairly coarse arsenopyrite is the chief sulphide mineral in these zones but, locally, they contain also pyrite and pyrrhotite. Where quartz and chlorite are present, rather coarse gold is associated with them. In that part of the main zone where gold assays have been most consistent, the diorite is rich in albite."

Jan 1, 1954

By Li Qihou, Liu Zhihong, Liu Zhiyong, Yao Wei

Black copper sludge, which mainly contains copper, arsenic and a little antimony, bismuth, selenium, tellurium, is an important recyclable secondary resource. In this paper, selective removal of arsenic from black copper sludge by alkaline oxidative pressure leaching was studied. The influences of alkali concentration, leaching time, leaching temperature, oxygen pressure, liquid-solid ratio and other variables on the leaching rate of arsenic, copper and tellurium were investigated. The results were as follows: when the leaching process was conducted at initial alkali concentration of 1mol/L, liquid-solid ratio of 10, stirring rate of 500r/min, leaching temperature of 140°C for 5 h and oxygen pressure of 2.5MPa, the leaching rates of arsenic and tellurium were 85.43% and 59.7% respectively, and copper, antimony, bismuth were not leached. Hence, arsenic has been removed effectively from black copper sludge, while the valuable metals such as copper, antimony and bismuth remained in the residue that can be further recovered easily. INTRODUCTION Black copper sludge is a byproduct in the purification process of copper electrolyte. Arsenic, antimony and bismuth are major harmful impurities in copper electrolytic refining system. The accumulation of these impurities will cause adverse effects, such as the increase of electrolyte resistance and power consumption and deterioration of cathode copper quality (Wang, Liu, & Zhang, 2001). Hence, electrolyte purification is an essential part of the electrolysis process (Liang, Chen, & Guo, 2009). Electrolyte purification methods include electrowinning (Davenport, King, Schlesinger, & Biswas, 2002), solvent extraction (Navarro, Simpson, & Alguacil, 1999), ion exchange (Arroyo et al., 2017), coprecipitation (Wang et al., 2003, 2018; Xiao et al., 2007; Xiao, Cao, Mao, Shen, & Ren, 2014), activated carbon adsorption (Navarro & Alguacil, 2002), electrodialysis (Cifuentes et al., 2015), redox process (Zhou, Peng, Zheng, Ma, & Cui, 2011; Peng, Zheng, Zhou, & Chen, 2012; Zheng, Peng, Ke, & Chen, 2013), among which the electrowinning method is simple in operation and effective in impurities removal, making it the main process for current electrolyte purification. Some copper ions can react with harmful impurities to form complex black copper sludge by controlling the operation conditions of electrowinning process. Based on the estimated data provide by Davenport et al. (2002), an annual output of 400,000 tons cathode copper could produce 432-2168 tons of black copper sludge by electrowinning method. Black copper sludge contains 30~50% copper, 15~30% arsenic and a small amount of rare elements such as selenium and tellurium. Thus, recovery of valuable metals can bring huge economic interests. Moreover, arsenic in these sludges could cause significant environmental pollution. Therefore, effective removal of arsenic from these sludges is urgent and significant.

Jan 1, 2019

By M. Takebayashi, K. Takenaka, S. Matsubara, T. Yoneyama

The cathode production of Toyo Smelter and Refinery, owned by Sumitomo Metal Mining Co., Ltd. reached 450,000 tons per year in 2016 with three tank houses. Niihama tank house commenced operations in 1919 with conventional sheet cathode technology. Approximately 100 years of operation experience and the technical development enabled that the current density of Niihama tank house and the Toyo tank house #1 increased to 320 A/m2. These operation techniques were utilized at the Toyo tank house #2 which started in 2005, and its current density reached up to 350 A/m2 with permanent cathode technology. In order to achieve high current efficiency under condition of 350 A/m2 operation at Toyo tank house #2, continued efforts had been made to verticality of anodes and permanent cathodes. To improve verticality of anodes and cathodes, reduction of short circuit ratio by changing the shape of the anode, optimizing the anode pressing machine and off-line process for rectifying the distortion of permanent cathodes was carried out. In addition, concentration control of electrolyte and expansion of Ni removing ability from the electrolyte prevented passivation. Finally, more than 96% of the current efficiency was stably confirmed. INTRODUCTION Today, Toyo Smelter and Refinery of Sumitomo Metal Mining operates three tank houses in Japan, namely, Toyo tank house #1, Toyo tank house #2, and Niihama tank house with a total capacity of 450,000 metric tons of copper cathodes. Figure 1 shows the trend of cathode copper production and the current density at three tank houses over the last 10 years. Cathode production by Toyo Smelter and Refinery reached 450,000 tons per year in 2016 with three tank houses.

Jan 1, 2019

By Shinji Shirakawa

The gold wire bonding technology is widely used for electrically connecting aluminum pads on IC devices to external terminal of semiconductor. In 1960?s, the tensile strength of gold bonding wire was about 100 MPa only. However, recently the wire with 300 MPa in strength has been developed. Since the gold bonding wire was started to use for IC package in early 1960?, the many types of gold bonding wire has been developing continuously in order to meet market?s needs, such as high density, small size and thin type of IC packages. Moreover, electronic equipments were used in automobile applications and also demanded good reliability under severe temperature environment. Thus Au-Pd alloy wire has been introduced instead of the wire with 4N(99.99wt%) purity gold to provide excellent reliability in Au-Al bond interface. The phenomena at Au-Al interface in the high temperature storage have been already explained by several studies as follows. There are five phases of inter metallic compound (IMC) between gold and aluminum. Just after bond gold ball on aluminum pad, Au5Al2 phase was formed and occupied almost all of IMC area. During high temperature storage test, Au5Al2 phase transformed to Au4Al phase, then this phase was corroded by Bromide (Br) ion that was isolated from molding resin. Thus the reliability between Au and Al degraded. In case of Au-Pd alloy wire, the concentrated palladium phase (Au-Pd-Al) was formed at the interface between Au alloy ball and Al pad. The Au-Pd-Al phase prevented from transforming between Au and Al, therefore Au5Al2 phase was hard to transform to Au4Al phase. Consequently the reliability at the interface between Au alloy ball and Al pad was less degradation. However, in recent study using several advanced analysis technique, Au4Al phase was found at the interface between Au alloy ball and Al pad same as the case of conventional gold wire (4N purity gold bonding wire). It was suggested that the formation of concentrated palladium phase (Au-Pd-Al) related the excellent reliability at ball bonding process.

Oct 1, 2003

By J. C. Salas, A. Weishaupt, J. A. Guzman

The origins of the electrorefining process date back to 1869, when the first ER cathodes were produced at Pembrey, South Wales. By the time that Pembrey was closing, Chuquicamata tank house was under construction, initiating in 1915 a long history of electrolytic cathodes production. Initially electrowon cathodes and later electrorefined cathodes were produced. During the history of Chuquicamata tank house, there have been several challenges associated with the quality demanded for electrolytic copper. Among them, the transformation from electrowinning to electrorefining in 1952, the onset of the direct commercialization of ER cathodes and the phase out of wire bars in the 80s, several technological changes including the implementation of permanent cathodes, and certainly the constant increase in complexity of the anodes refined. This paper explores the manner in which Chuquicamata has addressed these challenges and examines its links to process characteristics, which have been necessary to maintain a product quality according to market requirements and a brand, “CCC”, that is widely recognized worldwide. INTRODUCTION Located in the north of Chile, in the Atacama Desert, Chuquicamata is an open pit copper mine that for many years has played a relevant role in the global and local mining industry. Known from prehispanic times, the Chuquicamata deposit was initially developed between 1912 and 1915 by the Chile Exploration Company, the operating company of the Chile Copper Company controlled by the Guggenheim Brothers in the USA (Yeatman, 1916). Officially inaugurated on May 18th, 1915, by the President of Chile who pressed a button in Santiago sending a telegraph signal to the power generation plant specially built in Tocopilla, 1500 km north. It signaled the beginning of generating energy, sending it to Chuquicamata, another 140 km east (“El mineral de Chuquicamata”, 1915), marking the beginning of its industrial operation.

Jan 1, 2019

By Abdurrahman Tosun

It is very important for after blasting processes that muck pile fragmentation is predicted and controlled during blasting. Therefore, a significant research effort has been devoted to the development of mathematical equations that predict the value of average muck pile fragmentation. The specific charge parameter used in all of these equations is determined as the ratio of the total mass of explosives used to break a volume of rock. The length of blast surface and the row number of the blasthole are ignored in the calculation of the specific charge. However, in a blasting operation, blasthole geometry may result in additional material being impacted by a blasthole. This is due to effect shares of in both end sides of blastholes and the back region of blasting surface. In this study, a total of 14 blast tests, 8 at the first quarry and 6 at the second quarry of the Bati Anadolu (Western Anatolia) Cement Factory, were performed. In each study area blast tests were designed in the same direction continuously to provide stable structural properties of the rock. Therefore muck pile fragmentation depended on only specific charge values for each blast tests. Specific charge values were calculated according to both an average blasthole and also the total volume of material occurred as a result of blasting for each blast tests. During loading until the end of blasted material the front, the back, the arm off and the bucket off pump hydraulic pressure values occurred in hydraulic pistons of the loader were determined with a lot of data received for each blast tests. After that the relationships between specific charges values obtained according to two different methods and hydraulic pressure values of the loader were established with two correlations. The relationships between specific charges values obtained according to the total volume of material occurred as a result of blasting and hydraulic pressure values of the loader occurred as the best results especially the blasting operations that have the total length of blasting surfaces are short.

Aug 1, 2013

By Ron Bradburn, Derek Perkins

"The Brenda mine is located in south central British Columbia, 22 km north west of Peachland, in the heart of the Okanagan Valley. Situated at an elevation of 1500 metres, the mine area straddles the divide between the headwaters of Trepanier Creek and Peachland Creek. These flow into Okanagan Lake, the chief valley water resource located 1100 metres below. The creeks are of great significance to the water management of the area as they constitute the water supply for the Municipality of Peachland, a thriving retirement community with a population of 5000. A location map is shown in Figure 1.The history of the Brenda Mine operation has been well documented previously. After twenty years of operation, the open pit mine shut down in June 1990 due to the depletion of its ore reserves. During the course of its life, it produced 109 million tonnes of waste rock which is thought to contain approximately 0.10% copper as chalcopyrite and 0.015% molybdenum as molybdenite stored in four rock piles around the pit. Similarly, approximately 200 million tonnes of tailings were produced grading 0.015% copper and 0.005% molybdenum. During operation, tailings were hydrocycloned to produce a coarse sand for dam building with the fine slime stored behind the dam. It is estimated that 40% of the tailings were used for the dam construction. The layout of the mine site is shown in Figure 2.The mine was operated under a zero discharge permit. This was achieved by diverting practically all surface water flowing towards the mine area around the site. Water affected by mine operations, was discharged to the tailings impoundment, and recycled to the mill for reuse. The recycle rate was 90% and seepage from the tailings embankment and saddle dam was pumped back to the tailings pond. Because acid drainage was not a problem with the low grade Brenda rock, runoff from the rockpiles was initially released to the local environment. However, due to the alkaline nature of the waste rock, dissolution of low concentrations of molybdenum in the site runoff waters became evident by the late 1970's. The molybdenum content of Peachland Lake, the water reservoir for the municipality of Peachland, approached the Canadian Drinking Water Standard of 0.25 ppm. By 1979, a series of diversion and collection ditches was completed to direct all runoff water from the rockpiles to the tailings impoundment area. This had a significant detrimental effect on the site water balance causing it to go into a considerable surplus condition. During normal operation, this oversupply was contained by the rate of tailings dam building. An economic shutdown of the mine during 1984 forced a limited discharge from the site to protect the integrity of the tailings dam."

Jan 1, 1995

By José Cáceres

Mine To Mill? ? Carlisle(1954) ?The economic of a fund resource with particular reference to mining?. ? Steine(1978) ?Coarser grind may mean lower metal recovery but higher profit?. ? Metalica (1999) ?Mine Plant Integrated Planning?. ? JK (2002) Mine to Mill Strategic Planning ? Camus, Kelebek (2002) ?Management of Mineral Resources: Creating Value in the Mining Business?. ? Caceres (2003) ?Integrating Milling Parameters in the Mining Planning?

May 1, 2006

By R. H. Seraphim

"The Phoenix Camp, in the Boundary Creek district of southern British Columbia, produced before 1920 about 15 million tons of ore averaging more than l ·5 per cent copper, about 0.03 ounces per ton in gold, and 0·5 ounces per ton in silver. Attwood Copper Mines Ltd. conducted an exploration program in the Phoenix area from 1951to1953.Publications on the camp are listed in the bibliography. Brock's work was not sufficiently detailed to unravel the structural and stratigraphic pro bl.ems. The work of LeRoy and McNaughton is referred to later.The stratigraphic column is as follows:Tertiary.Midway Formation: Volcanics and hypabyssals; dacitic to basaltic flows, with associated dykes and sills of syenite (pulaskite in part) and augite porphyry.Jura-Cretaceous.Intrusives of quartz diorite and diorite (nearest outcrop two miles from Phoenix).Late Palaeozoic or Triassic (Attwood Series).Brooklyn Formation: Sharps tone conglomerate, limestone, grey-wacke and/ or andesitic tuff, with minor shale and basalt. Rawhide Formation: shale with minor conglomerate.Early Palaeozoic.Knob Hill Formation: Chert and andesite, with minor limestone, shale, and serpentine.This column differs from that of LeRoy in two important respects: (I) Attwood's work indicates that the Rawhide shale is basal to, rather than stratigraphically above, the Brooklyn formation. The shale contains conglomerate lenses, which become more abundant and thicker toward the top, and grades upward into Brooklyn conglomerate. Ripple marks indicate that the shale is right side up."

Jan 1, 1949

By Tiago Webber

Mineral resources estimation comprises basically two stages: (i) data collection, analysis and validation, and (ii) the estimate of the grades and tones of the deposit. The most applied method for sampling survey in mineral exploration is rotary drilling with total core recovery. High drilling costs make borehole geophysical logging attractive to obtain the maximum possible information from each borehole helping to understand ore intersections, grades variability, limits of the deposits and continuity of the mineralization. In this paper, borehole geophysical logging was used to enhance the sampling survey and to derive grades indirectly (without lab analysis) with a certain amount of uncertainty. Indicator kriging (IK) was the estimation method used, as it is adequate to incorporate the uncertainty associated with the geophysical derived grade values. The results were compared to the conventional procedures using grades determined via core analysis and ordinary kriging. Borehole geophysical logging proved to be efficient to define the essential features of ore deposit and IK provided results with acceptable precision and accuracy if compared to the model provided by ordinary kriging.

Oct 1, 2009

By T. Yalcin

"This paper describes a process that can provide high rates of dewatering and that has the potential of bringing significant savings in tailing disposal costs. It involves a three-stage, closed-circuit operation employing a hydrocyclone, a settling cone and a thickener. The mill tailing, with adjusted pulp density, is first fed to the hydrocyclone. The underflow from the hydrocyclone goes to the settling cone for further dewatering. The overflows from the hydrocyclone and the settling cone are sent to a thickener which, with the addition of a flocculant, gives a clear liquid effluent and a dilute underflow which is recycled back to the hydrocyclone. The underflow of the settling cone is a material with as high as 78% pulp density and is suitable for direct disposal or for use as mine backfill.INTRODUCTIONDewatering is an essential process for the disposal of mill tailings and forms an additional cost item in milling operations. Cost-cutting measures are therefore desirable in this area as in any other stage of milling. One way of achieving this is through increased rate of dewatering which would require smaller dewatering units with correspondingly lower capital and operating costs."

Jan 1, 1987

By Rolf Andreas Lauten, Guy Kluck

"Formation of scales may have important detrimental effects in many mineral processing applications. A well-known problem is the need for frequent maintenance to remove scale from processing equipment. Another challenge may relate to encapsulation of valuable minerals in precipitating scale. In this work, we explore the ability of some crystal growth inhibitors to prevent or lower the degree of scale precipitation. In many situations pregnant leach solutions contains substantial concentrations of calcium, magnesium, sulfate and carbonate in addition to dissolved valuable elements, e.g. gold, copper, zinc. Together with non-dissolved gangue minerals, some slurries may also contain particulate gold, copper etc. During normal processing of the pregnant leach solution it may be exposed to temperature gradients or similar promoting precipitation of various scales. Valuable minerals may become entrapped in precipitates and thus become inaccessible to the lixiviant. Use of a crystal growth inhibitor may lower the degree of encapsulation of valuable elements.Using a simple model system, supersaturated with respect to gypsum, the effect of some crystal growth inhibitors on the prevention of scale is evaluated in terms of amount precipitated gypsum, the particle size of the precipitated gypsum and the carbon gold loading capacity.INTRODUCTIONGold bearing sulfide ores are often roasted or pressure oxidised prior to leaching. The purpose of this unit operation is to prevent loading the leaching circuit with sulfides that consume cyanide. Pressure oxidation or roasting chemically converts the sulfides into sulfates and at the same time, the pH of the slurry ends up in the acidic range. Typically, lime addition is the preferred means to raise the pH to around 10 where gold leaching takes place. Combination of large amounts of calcium ions from the lime with sulfate ions from the ore induces precipitation of gypsum. Compounds like calcium carbonate may also precipitate if carbonate ions are present in the slurry. Depending upon the composition of the ore, compounds like calcium carbonate and other types of scale may also precipitate on gold surfaces on the slurry particles. A layer of scale on top of exposed gold surfaces will prevent dissolution in the cyanidation that takes place during leaching. Naturally, such a precipitation may lower the gold recovery."

Jan 1, 2016

By Jeffrey D. Eisenman

FRP is a proven material for the solvent extraction processes of copper production. There is a history of successful applications of FRP piping and equipment in hydrometallurgical processing. The performance of FRP equipment has not always been consistent, but at no fault of the material. Its non-metal attributes and behavior vary from those of more typical materials of construction, such as steel and alloys. FRP is a mainstay material in many areas of solvent extraction and electrowinning and yet not well understood by all. We will discuss the critical concerns, which are key to reliable performance of FRP systems. This paper will include discussion of key elements, which are fundamental to reliable FRP piping design and considered best practices. Essential design and construction considerations to maximize reliable service life of FRP equipment, such as thickeners and process vessels, used in copper extraction and processing, will be discussed. Additionally, we will expose potential pitfalls and share lessons learned from previous copper processing plant projects, which can aid and impact other copper processing projects to ensure best system performance and reliability. INTRODUCTION The corrosion resistant attributes of fiberglass reinforced plastics (FRP) make it an attractive and cost effective material of construction in corrosive service applications that are found in copper processing. FRP is used all over the processing plant in seawater, brine and sulfuric acid services where the corrosive nature of these services would challenge most ferrous materials and coatings. FRP is a fully customizable material to meet the specific needs of each service and process. FRP piping and equipment can be found throughout the hydrometallurgical process, in the acid plant, desalination, leaching processes, solvent extraction and electrowinning to name a few. Beyond its superior corrosion resistant characteristics, FRP can be made abrasion resistant by introducing particulate additives into the resin, such as silicon carbide and alumina oxide. Because many of these services have combustible organic elements in the flow streams with accompanying safety concerns, the linings can be made conductive with carbon fibers to dissipate static charges that might collect on the surface of the equipment otherwise. Further, FRP can be made flame retardant as well, where flammability may be of concern.

Jan 1, 2019

By I. Osvath, I. Gombköto, G. Mucsi, Z. Molnár

"In the present research, a deposited brown coal fly ash was used as raw material for geopolymer. The reactivity of the fly ash was altered using mechanical activation, which is one of the promising methods to improve bulk and surface reactivity. The mechanical activation experiments were carried out in a high energy density mill using 5 m/s circumferential speed, and various residence times (1, 3, 5, 10, 15 and 60 min). The effect of mechanical activation on particle size distribution was measured by a laser particle size analyzer and structural changes using FT-IR. Geopolymer samples were prepared from mechanically activated fly ash with an alkali solution. The progress of geopolymerisation was monitored using an Isothermal Conduction Calorimeter. The heat flow curve obtained indicated that reactions were more prominent and started much earlier in the mechanically activated samples. This observation is further supported by the compressive strength results which also improved in geopolymers using mechanically activated fly ash. Based on the obtained results, it can be inferred that mechanical activation is a possible way to enhance the reactivity of fly ash and consequently properties of resulting geopolymers.INTRODUCTIONCoal fired power plants generate fly ash and slag in huge amount worldwide, about 780 million tons/year (Heidrich et al. 2013). Due to the relatively low utilization rate, enormous quantities of these wastes are landfilled in ponds. The fly ash is the finest grained particle fraction of the solid ash, which is transported with flue gas, and removed by electrostatic or bag filters. The fly ash has pozzolanic activity, it does not react with water, but in the presence of calcium hydroxide solution hardens and solidifies, producing a reaction product practically insoluble in water (Opoczky, 2001). The most important property of the fly ash regarding geopolymerization is its reactivity, which depends on the chemical and phase composition, the dispersity (specific surface area, particle size distribution), and the morphology of the fly ash particles, and determined by the physical properties and chemical composition of the fly ash. Geopolymers concerning their chemical structure are polysialates, where the sialate (silicon-oxoaluminate) network is built up from the bonds of Si-oxide and Al-oxide by sharing oxygen atoms (Davidovits, 1988)."

Jan 1, 2016