Search Documents

By G. Portillo

Electrospark Deposition (ESD) is a pulsed-arc micro-welding process characterized by using high current electrical pulses, of a short duration, to deposit an electrode material on a metallic substrate. The short duration of the electrical pulse allows for a low heat input over the substrate and an extremely rapid solidification of the deposited material. As a result, the ESD is capable of a wide variety of microstructures like micro-segregationfree solid solutions, nanostructured grains, metastable structures, and amorphous phases. The present work shows a microstructural analysis of rapidly solidified Al-Ni alloys coatings by the ESD process. Field Emission Scanning Electron Microscopy (FE-SEM) and X-Ray Diffraction (XRD) were performed to present the microstructural evolution as a function of the welding parameters. The phases and non-equilibrium metastable structures present in the alloys, and their distribution, were found to be a sensitive function of the alloy composition; hence its formation is governed primarily by thermodynamic considerations.

Jan 1, 2011

By R. Farhat

Coating systems that yield a thermally grown oxide (TGO) protective layer have been proposed as a potential method for extending the lifecycle of components exposed to high temperature corrosion. This is particularly relevant to the petrochemical industry, where any reduction in corrosion rates can yield substantial cost reductions. The primary goal of this project is to develop a coating repair procedure and to investigate the oxidation performance of the repaired location. Electrospark deposition (ESD) was used to repair spalled segments of TGO grown on MCrA1Y substrates using various electrodes possessing mixed crystal structures. Specifically, electrodes of NiCoCrA1Y (BCC-FCC mixtures) and CoNiCrA1Y (FCCBCC mixtures), were deposited and oxidized to develop the TGO using a heat treatment of 24 hours at 1000°C in air. This presentation will focus on the microstructural evolution of the base metal and ESD repair on damaged area, in both as- deposited and oxidized forms. Results of SEM and XRD analysis will be presented.

Jan 1, 2011

Polymer electrolyte membrane (PEM) fuel cell has increasingly become the potential choice of zero-emission power source for portable, mobile and stationary co¬generation applications. However, technical barriers need to be overcome before its widespread commercialization; cost reduction and performance improvement including reliability are the two key areas, that can be realized through better cell/stack design and improved understanding of the transport processes occurring inside the individual cells and stacks. In this presentation, we will provide an overview of various cell/stack models that are available in the literature, their strength and weakness, and then present a comprehensive multi-species, multi-phase and multi-dimensional formulation of a single PEM fuel cell, with consistent and systematic formulation for all the regions involved, including the solid bipolar plates, gas flow channels, the electrode backing layers, the catalyst layers and the electrolyte membrane. Such a detailed approach allows us to extract sufficient information to the analysis of a stack of PEM fuel cells. Stack model will be presented that investigates the various stack designs and flow configurations, and the optimal stack design based on the present study will be described. Also some innovative cell/stack designs will be featured.

Jan 1, 2005

By H. Saari, M. Pates, P. C. Patnaik, A. Merati

Single crystal nickel-base superalloys such as PWA1484 exhibit superior performance compared to conventional superalloys, and are used extensively in turbine blade applications requiring good high temperature properties. The life of these blades is typically limited by cracks and erosion. Due to the high cost of these blades, welding techniques are being considered to weld/repair worn components, extending their useful lives and delaying the need for expensive replacement components. However, the sensitivities for solidification cracking and post weld heat treatment cracking are relatively high in these alloys. Electron beam (EB) welding can deliver concentrated heat sources and has the potential to address these issues. Numerous welding trials and structural tests must be conducted to identify the optimum method and welding parameters. Weldability is studied over a range of material conditions, welding parameters, and directions. The influence of welding parameters on the fusion zone microstructure and resultant weldability is investigated using combination of microscopic examination and micro-hardness testing. This paper summarizes some of the results of a feasibility study conducted to understand the effects of welding parameters on localized microstructural features, cracking sensitivity, and mechanical properties of autogenously EB welded coupons of single crystal PWA1484.

Jan 1, 2004

By K. Yoo

Chalcopyrite is the most abundant copper sulfide mineral, which is normally processed using pyrometallurgical methods (i.e., smelting) to produce copper metal. Smelting has several major disadvantages, such as high gas-handling costs, high capital costs, saturation of sulfuric acid market, and inability to treat low-grade concentrates and to recover some by-products, such as zinc, nickel and cobalt. The development of hydrometallurgical processes for chalcopyrite is desirable to overcome the problems of smelting. Because chalcopyrite is refractory, the leaching rate for chalcopyrite is very low. Therefore, increasing the leaching rate has been extensively investigated, both in sulfate and chloride media, as well as in the presence of bacteria. Chloride leaching processes have shown relatively high leaching rates. The mechanism of the chloride leaching process has been investigated, but the behavior of chalcopyrite leaching in chloride solution is not clear. Therefore, the effect of the solution redox potential on the leaching rate of chalcopyrite in chloride solution was investigated. In the present study, leaching experiments were carried out using 0.1 M chloride solutions and the results indicate that high leaching rates of chalcopyrite can be achieved at relatively low solution redox potentials.

Jan 1, 2007

By B. Zhu, W. E. Lee, N. Li

Al powder is used extensively as an antioxidant in carbon-containing bricks, but it cannot be used directly in water-based carbon-containing castables due to its hydration tendency. To overcome this problem, in this work, SiO2-PVA (polyvinyl alcohol) inorganic-organic hybrid coatings have been prepared via sol-gel processing, and used to coat Al powder. The hydration behaviour of uncoated and coated Al powders has been investigated in water at 60 or 100°C for 36h by examining phase and microstructural changes. While significant hydration is detected in uncoated Al powder, no obvious hydration is detected in coated Al powder, indicating that its hydration resistance has been greatly improved. Oxidation resistance of graphite coexisting with uncoated or coated Al powder was also investigated in air at 1250°C for 1.5h. The oxidation ratio of graphite coexisting with coated Al powder was similar to that of graphite coexisting with uncoated Al powder, indicating that both powders showed similar antioxidising behaviour. This, along with the much improved hydration resistance, makes the coated Al powder a potential antioxidant in carbon-containing castables systems.

Jan 1, 2004

By Arthur Lieu

The mill effluent treatment circuit (Bulk Neutralization (BN)) in the Cameco Key Lake Operation was modified in 2008 to enhance the removal efficiency of selenium (Se) and molybdenum (Mo) from the mill process water. This modification was completed in part due to increased knowledge of the effects these elements have on biota. In addition, legacy effects from the historical operation of the Key Lake mill in regards to Se and Mo were shown to have an effect on the regional biota in the downstream receptors. This was a challenging initiative as there was no off the shelf technology available and the removal process had to be incorporated into an existing (brownfield) process. These modifications have resulted in significant reduction in the concentration of these elements in the Key Lake mill effluent. The removal efficiency for Se and Mo in the modified circuit has increased to 95% and 75%. As a result, concentrations of Se and Mo are now consistently less than 0.4 mg/l and 0.02 mg/l. In addition, the Se and Mo precipitates formed were extensively studied to ensure long-term geochemical stability in the Key Lake in-pit tailings facility. This presentation will provide additional detail on the hydrometallurgical removal mechanisms and process modifications required in the Key Lake BN circuit to remove these elements to trace levels.

Aug 1, 2010

By M. Gruber-Pretzler

Technical Sn- bronzes tend to form both macrosegregations and microsegrega¬tions during DC-casting due to the particular thermodynamic properties and kinetics of phase transformation. As a result a heterogeneous cast microstructure forms that is some¬times a reason for a decrease in workability. The extent of macrosegregations in DC-casting can effectively be influenced by casting parameters like casting velocity, primary cooling or inlet geometry which in fact change the relative flow between the melt and the forming solid. In order to understand the influence and interaction of the related phenom¬ena, simulation methods are applied. The solidification of the strand as well as the forma¬tion of macrosegregation are simulated with a two phase volume averaging model. The velocity field of the melt flow is explicitly calculated by solving the corresponding mo¬mentum conservation equations. Within the mushy zone the local formation of microseg¬regations in the presence of feeding flow is estimated. The thermodynamics of the Cu-Sn system is accounted for and it is distinguished explicitly between interface and average concentrations. To investigate the influence of feeding flow on the formation of mac-rosegregations, a study has been performed. Based on this result, the phenomena of mac¬rosegregations are described in a detailed discussion.

Jan 1, 2007

By Jeffrey D. Smith, William G. Fahrenholtz, Jose M. Soto

Interactions between A356 aluminum (Al-Si alloy) and dense fused silica (FS) riser tubes used for low-pressure casting of aluminum alloys were evaluated using a sessile drop approach. The tubes have a short service life, but cost and thermal shock resistance make them an effective solution. The main problem encountered during use is the reaction of aluminum with silica to form alumina and silicon, which causes failure. Tests have been conducted on as-fired (uncoated) and modified (coated) tubes. Experiments were carried out in a horizontal furnace at 1225°C under argon to minimize the effect of the aluminum oxide on the interactions at the alloy-silica interface. Images of the drop were acquired and contact angle values were estimated for uncoated and coated samples, but no significant differences in the contact angles were observed. Scanning electron microscopy revealed the presence of cracks at the interface between the reaction zone and the unreacted silica. The presence of reaction products (silicon in the reacting alloy and aluminum in a reaction zone between the alloy and the unaffected silica) has been confirmed using energy dispersive spectroscopy. A two layer coating system was found to be effective in reducing penetration of the aluminum alloy.

Jan 1, 2004

By David Morley

This paper considers the ideal truck-excavator combination, defined as the combination resulting in the lowest direct unit cost, in consideration of multiple haul scenarios characterized by different haul distances, material and equipment availability. Through the application of Monte Carlo simulation, selected for its unique ability to handle the uncertainty of activity durations, the ?four to six passes? loading rule is shown to not correlate with the selection of the minimum cost fleet. Additionally, through the results of the simulation it is determined that the haul truck capacity has a greater effect on the overall efficiency of the system than does the excavator capacity. As a result, in order to arrive at efficient operations, the entire earthmoving system must be viewed as whole, namely, considering haulers together with excavators, as opposed to the popular method of first selecting a loading unit and then selecting a hauler obeying the ?four to six passes? loading rule. Furthermore, truck utilization and excavator utilization exhibit an inverse relationship and neither directly correlates with the overall efficiency of the earthmoving operation. The following conclusions are drawn: first, with limited financial resources, it is more valuable to increase hauling unit size before increasing loading unit size and second, predefined rules or generalizations, not based on evidence, potentially eliminate optimal truck excavator combinations from being considered.

Aug 1, 2013

"Adopted in 2003, theses guidelines are intended to assist the Qualified Person(s) in the planning, supervision, preparation and reporting of mineral resources and mineral reserve estimates. The report is divided into two broad sections “General Guidelines” appropriate for most metals and “Guidelines Specific to Particular Commodities” for potash, industrial minerals, uranium and coal. “These guidelines are reference in the Companion Policy of NI 43-101 with a statement that a qualified person classifying a mineral deposit as a mineral resource or mineral reserve should follow them.”Executive SummaryThe following is a summary, in table format, of the main elements of the Estimation Best Practice Committee's report ""Estimation of Mineral Resource and Mineral Reserve Best Practice Guidelines"". While the summary table is provided for convenience, the Committee recommends that the report be read in its entirety and the table summary not be used as a stand alone document. These guidelines are not intended to be either prescriptive or exhaustive. They do not preclude innovation. Preamble: These guidelines have been prepared by the Canadian Institute of Mining and Metallurgy and Petroleum (CIM) led Estimation Best Practices Committee. They are intended to assist the Qualified Person(s) (QP) in the planning, supervision, preparation and reporting of Mineral Resource and Mineral Reserve (MRMR) estimates. All MRMR estimation work from which public reporting will ensue must be designed and carried out under the direction of a QP in accordance with National Instrument 43-101 (NI 43-101) and related forms. A QP is defined in NI 43-101 as ""an individual who is an engineer or geoscientist with at least five (5) years of experience in mineral exploration, mine development, mine operation, project assessment or any combination of these; has experience relevant to the subject matter of the mineral project and technical report; and is a member in good standing of a professional association"". Disclosure of MRMR estimates is to be made in accordance with industry standard definitions approved by the CIM (the CIM Standards adopted by the CIM Council in August 2002) which have been incorporated by reference into NI 43-101."

Jan 1, 2003

By J. Vanderlaan

A proposed method of applying high-speed, non-destructive part scanning technologies to the production process of UO2 (Uranium Dioxide) fuel pellets is presented. The scanning process examines each pellet individually for correct surface roughness and any surface imperfection or defects. Using optical scanning methods, which consist of laser and CCD camera technology, the complete circumferential surface of the pellet is examined to meet the reactor fuel bundle specifications.

Aug 1, 2010

By Mohammad Mehdi Salarirad

Fouling of activated carbon by different organic species is a great concern in carbon in pulp and carbon in leach circuits. The rate of gold adsorption onto activated carbon from synthetic gold solutions which contained different amounts of potassium ethyl xanthate (PEX), potassium isobutyl xanthate (PIBX), and methyl isobutyl carbinol (MIBC) were evaluated through batch adsorption tests. The results of these experiments showed that the gold sorption rate rapidly decreases by increasing the concentration of collectors including PIBX and PEX up to 20 mg/L and at higher concentrations, the kinetic rate constant (i.e., k value) gradually leveled off to 53 h-1 for PIBX, which is 46% lower than the 99 h-1 for PEX. At low concentrations of up to 15 mg/L of MIBC, a gradual decrease of the rate constant was observed, while at higher concentrations, the decrease was found to be more pronounced. The gold loading capacity and the rate of gold adsorption onto activated carbon from a gold cyanidation pulp in the presence of flotation reagents were also evaluated. The results of these experiments showed that the flotation reagents have no significant effect on the gold loading capacity of activated carbon at prolong adsorption period, meanwhile the rate of gold adsorption continuously decreases by increasing the concentration of flotation reagents in the leaching solution.

Oct 1, 2011

By Z. -G. Ren, J. -S. Qian, Y. -G. Yang

The waste slags from chemical and metallurgical plants contain approximately wt 1% water soluble Cr6+. This hexavalent chromium is very harmful to human health, and the treatment of the slags has concerned metallurgists for many years. A sintering method was developed to treat the waste slag. In this process, sinter was made from a mixture of the waste slag containing hexavalent chromium, iron concentrate and coke breezes. During sintering, hexavalent chromium was reduced to trivalent chromium. The latter is known as a non-harmful material and can be used as chromium resource for the production of ferrochromium or chromium-containing cast iron. After sintering the hexavalent chromium in the sinter could be reduced to less than 0.0008%. It was found that the waste slag with fine particles was favourable to the Cr6+ removal. An increase of carbon content in the sintering mixture could increase the rate of Cr6+ removal and the strength of the sinter produced. The rate of Cr6+ removal increased with increasing basicity of the sintering materials with basicity less than B=1.8, above which it decreased with increasing basicity. Blast furnace was found to operate smoothly when using the sinter made from the waste slag containing chromium. However the productivity of sintering machine was slightly low compared to the sintering operation using ordinary raw materials.

Jan 1, 2004

By J. C. Glandus, N. Tessier-Doyen, M. Huger

The Young's modulus of bi-phased model materials (vitreous matrix containing spherical alumina inclusions) have been determined by two complementary approaches: experimental and analytical. If the matrix and inclusions exhibit close coefficients of thermal expansion, the experimental results lie in the vicinity of the lower bound of the Hashin & Shtrikman's model. If there is a dilatometric disagreement between the components, untypical behaviors, similar to those obtained for a family of industrial refractory materials, were observed when the temperature varies.

Jan 1, 2004

By Jian Li, V. Y. Gertsman, David C. Katz, M. Elboujdaini

Analysis of stress corrosion cracking (SCC) usually involves high-end analytical tools including scanning electron microscope (SEM) and analytical transmission electron microscope (TEM). In recent years, focused ion beam microscope (FIB) has found many applications in materials science fields. In this study, high-resolution FIB images have shown details of crack morphology and a plan-view TEM specimen containing the selected crack-tip was successfully prepared. The preparation of cross-sectioned samples containing crack tips was of paramount importance for subsequent TEM analyses.

Jan 1, 2004

By Michael Schindler

Uranyl mineral dissolution appears to be complex, affected by factors such as solution pH and the presence of various cations in solution, and sometimes involving formation of secondary surface precipitates. Such secondary precipitates potentially could armor the underlying uranyl mineral surfaces from further dissolution. A detailed understanding on the formation of secondary precipitate is therefore essential for predictive modeling of radionuclide fate and transport in the subsurface. Several types of secondary precipitates on the surface of uranyl minerals were examined using Atomic Force Microscopy, Scanning Electron Microscopy, and, Xray Photoelectron Spectroscopy.

Aug 1, 2010

By Michel Noël

This paper presents a partial compilation of adopted measures of waste rock dump closures at mine sites located in Canada and Alaska, where the climate includes cold winters. The paper also presents the selection process that was followed for some of those mine sites. Mining operations usually generate waste rock that can sometimes result in very large quantities. Additionally, the nature of the ore body and the host rock will often introduce environmental impacts. These impacts need to be managed not only during the operations but also in the long term. Mine closure plans consequently have to address the long term issues that sometimes require perpetual treatment. Closure planning often involves the evaluation of risks associated with environmental and financial liabilities. It needs to consider the science, some common definition of objectives, and there will be a need to manage resources and schedules. Closure planning is essentially an exercise in constrained decision making. A performance and risk based ranking matrix is often developed during this selection process to identify the preferred option(s). The case studies presented in this paper provides a few examples. The level of knowledge on acid rock drainage from waste rock dumps has increased considerably over the past decades. It did not necessarily increase the level of complexity of the adopted closure methods, as the selected closure methods are often kept simple. A common approach consists of stabilising the slopes of the waste rock dumps material by resloping and then covering the waste rock with a growth media to support vegetation. Such covers prevent direct contact of animals with the waste rock material, minimise erosion and reduce infiltration to various degrees. The inclusion of water treatment is obviously dependent on the water quality being released.

Nov 1, 2008

By R. M. Kalanchey

The application of pressure oxidation processes to copper feed materials has gained increased exposure in recent years and some of these processes have made commercial inroads, although rather limited to date. Among the hydrometallurgical processes with significant commercial potential, Dynatec's copper pressure leaching process has been applied to arsenic-bearing copper materials and has shown, through a number of batch and continuous test programs, that pressure oxidation is a technically feasible option for the recovery of copper with coincident sequestration of arsenic in an environmentally benign residue.

Jan 1, 2007

By D. Kim

Kennecott operates one of the largest and most modern copper refineries in the world at Magna, Utah, USA. The inputs to the refinery are anodes produced at Kennecott Smelter, which has extremely high contents of lead and bismuth. In order to minimize undesired effects in the electrolytic refining process, unwanted impurities, especially bismuth, must be controlled. This paper describes the process development of practicing state-of-the-art quality control and presents the pilot test results of using the MRT Technology for Bi production.

Jan 1, 2007