Search Documents

By Glenn Kosick, Roger Amelunxen, Glenn Dobby

"The variability in flotation response within an orebody is often a significant problem to address during the design phase of a flotation circuit. In addition, for existing operating plants, the reasons for such a variability need to be clearly understood and accounted for if plant performance is to be optimized. MinnovEX Technologies, in collaboration with major mining companies, is developing methodologies and tools to address the issue of variability in ore characteristics (such as ore hardness and flotation response). The tool is used for design and scale-up of flotation circuits from lab flotation data, and for prediction of recovery and final concentrate grades throughout the mine block model for any given circuit design.INTRODUCTIOTNH: EI SSUEB EINGA DDRESSEDThis paper describes the current development of a methodology and software tool for improved flotation plant design and enhanced prediction of froth flotation performance in an operating plant. The need for this tool is attributed to two primary factors: variability of flotation response properties throughout an orebody and related difficulties with scaleup from laboratory tests. Consider these in more detail.It is well recognized that separation performance via froth flotation will vary significantly within a single mineral deposit. This has been enhanced through the wide application of SAG milling. Throughput with SAG mills is more susceptible to ore hardness changes than is the case with crushing-rod-ball circuits; it is not uncommon to see SAG mill throughput to vary by up to 100% on a regular basis, e.g. 1000 tph to 2000 tph.The implication of this on laboratory testing for prediction of metallurgical performance is as follows: it is unlikely that either the plant grind (size distribution) feeding froth flotation or the flotation residence time will be known at the time of laboratory testing for a given block of ore. Hence, the grind used for the laboratory test is not likely to be that which actually occurs once the ore is processed, and the laboratory retention time may not represent the plant conditions."

Jan 1, 2002

Adsorption of guar gum was investigated on model minerals typically found in water-insoluble slimes of potash ores. The ionic strength of the adsorption mixtures was varied from distilled water to saturated NaC1 and KC1. The tests were also performed using a saturated brine. The adsorption density of guar gum on illite, dolomite, and kaolinite was found to be not only a function of total ionic strength but also of the type of electrolyte present in solution. Generally, the adsorption of the polymer on the clay minerals was higher in KC1 solutions than in NaCI, but the differences gradually disappeared when the electrolyte concentration approached saturation. The results were analyzed in terms of chaotropic (K ) or kosmotropic (Na') properties of background counter-ions and their different behaviors at the hydrated mineral-water interface. Guar gum adsorption on dolomite was related to the presence of calcium and magnesium sites on the mineral surface, and to the cis-configuration of OH groups of mannose units. Based on viscosity measurements, it was suggested that guar gum macromolecules form entanglements in NaCI solutions (and distilled water), but individual molecules exist in KC1 solutions thus creating different modes of adsorption of guar gum from concentrated NaCl and KCl solutions.

Jan 1, 2006

By Peter Fullagar, Adel Vatandoost, Steve Walters, Toni Kojovic

"Traditional comminution tests are a vital component in every mine plant design. Comminution behavior governs both the cost of equipment and its operating efficiency. Most comminution tests are conducted off site on a limited number of samples, owing to the high costs and long lead times involved. Therefore a strong incentive exists to find alternative means for efficiently characterizing comminution behavior for a truly representative suite of samples. The potential for inferring comminution behavior from drill core is investigated in this paper. Our approach involves development of small scale comminution tests on the one hand, and measurement of a wide range of core attributes on the other. Our focus is the relationship between petrophysical properties and comminution behavior.Petrophysical properties of archival diamond drill core from the Ernest Henry Mine (Queensland, Australia) have been measured using a Geotek multi-sensor petrophysical core logger. We have investigated the relationship between the petrophysical properties and the corresponding small scale A*b and estimated Bond mill work index test results for 2m composites of the core. Core samples were petrophysically classified by means of cluster analysis. Comminution behaviour was then modeled for each cluster via multiple regression. The results suggest that prediction of the comminution behavior on the basis of petrophysics is viable at Ernest Henry.INTRODUCTIONMineral processing is the most important downstream operation for mining engineers and metallurgists since most mined materials are subjected to some type of comminution or beneficiation operation (SME, 1992). Comminution or size reduction is typically the first stage of processing. Size reduction steps (crushing and grinding) in any plant consume large amounts of energy, normally more than 50% of total energy (Weiss, 1985). Therefore, it is desirable to obtain laboratory results to design the size reduction equipment appropriately. One of the main factors that control the selection of hard-rock crushing equipment and the design of a crushing circuit is the mechanical character of the ore(s). Work index, density, abrasivity, compressive strength and clay content are essential parameters for ore characterisation (SME, 1992)."

Jan 1, 2009

By Dong-kil Lee

Field tests have been conducted to investigate the characteristics of flow and physical chemistry of acid mine drainage(AMD) in the Hwangji-Yuchang settling pond in south Korea. pH and ferrous concentration of AMD flowed in the settling pond is 6.79 and 25.5 mg/l, respectively. As a results, we found that the ferrous oxidation reacted strongly around the inlet of the pond and the distributions of physicochemical properties is depended on flow characteristics and ferrous oxidation rate of AMD.

May 1, 2011

By Jörg Fischer-Bühner

Conventional 22ct Au jewellery alloys are comparably soft in the as-cast and soft-annealed state and hardening by cold-working is the only way of giving strength to the jewellery. The paper first focuses on hardening of 22ct jewellery alloys by conventional means, i.e. solid solution hardening with base metals (aiming particularly at an increased as-cast hardness) as well as precipitation hardening by alloying with base metals beyond the solubility limits and subsequent age-hardening heat treatment. Co-additions of ~2% turned out to result in most pronounced solid solution hardening up to ~100 HV1 in an investment cast & quenched state. Subsequent heat treatments, consisting of solution annealing at 850°C for 1h followed by water quenching and ageing at 300°C ? 400°C for ~ 1h lead to pronounced age-hardening with a peak hardness of ~ 260 HV1. In contrast, 22ct Au alloyed with Ni, Fe or Sb display no age-hardening effect within the same range of heat treatment parameters. The 2nd part of the paper reports on some preliminary trials to enhance the hardening effect of the base metals by additions of suitable elements, which possess a strong tendency to phase formation with the added base metal during ageing treatments. It is shown, that the age-hardening behavior of 22ct and 990/995 Au alloyed with Co or Ni can be remarkably influenced by additions of Sb. A total of only 10wt%0 of CoSb or NiSb-additions lead to a peak hardness of ~ 150 HV1 for a 22ct Au and ~ 100-120 HV1 for 990 Au , which is obtained already after very short ageing times (20-40min) at 300-400°C after solution annealing at 700°C / 1h / water quenching. It is suggested that the age-hardening mechanism in these alloys consists in precipitation of intermetallic CoSb- and NiSb-phases.

Oct 1, 2003

By M. Peshko, J. C. Gingerich, L. W. Matthews

"Noranda has successfully developed and implemented two leading-edge mineral exploration technologies — hyperspectral remote sensing and 3-D seismic surveying. Airborne hyperspectral imaging provides detailed geological and mineralogical mapping capability at both a regional and project scale that facilitates improved selection of prospective terrain and an accelerated exploration cycle. Noranda, in partnership with Falconbridge, has licensed the exclusive use of the Earth Search Sciences Inc. (ESSI) Probe-1 hyperspectral scanners (128- channel, 0.43 µm to 2.5 µm spectral range) that are capable of mapping in excess of 3500 km2 per day at 10 m pixel resolution. The technology has been successfully deployed on four continents over a broad range of terrain from desert to boreal forest and the high Arctic.To augment the company’s deep search initiatives, Noranda has successfully modified and implemented existing 3-D seismic technology to help targeting massive sulphides located at depths ranging from 500 m to 2000 m. In the fall of 1998 and early 1999, Noranda completed an 18 km2, 3-D seismic program in eastern Canada by successfully drill testing acoustic impedance anomalies locating massive sulphides at depths in excess of 1100 m."

Jan 1, 2002

By Gianni Bartolacci, Patrice Nadeau, Szatvanyi. Gerard, Carl Duchesne, Claude Chrétien

"Combustion is used throughout the mineral processing industry to produce steam in boilers, to dry concentrates in rotary dryers, and to apply heat treatments in pyrometallurgical furnaces. Tight combustion control is very important in latter type of furnace since the combustion conditions directly affect final ore quality. However, achieving tight combustion control is not straightforward since most of the flames encountered in industry are turbulent non-premixed flames, they are affected by several unmeasured disturbances and are often produced by burning several types of fuel simultaneously, some of them coming from other parts of the plant. A novel method is proposed in this paper to improve process and product quality control as well as to optimize the combustion conditions based on digital flame color images. Multivariate Image Analysis and Regression is to used extract the flame color characteristics from images to predict the solids discharge temperature of an industrial rotary kiln. It is shown that this method yield extremely good 10 minutes ahead forecast of the temperature and should lead to a substantial reduction in product quality variability as well as in fuel consumption.INTRODUCTIONFuel-fired furnaces are often used in the mineral processing industry for various purposes, such as for the production of steam (utility boiler), in conjunction with rotary dryers to dry mineral concentrates or in pyrometallurgical processes for induration, roasting, and so forth. These furnaces are necessary in the supply chain from the mine to the metals, but their operating costs are constantly rising due to the fluctuations in fuel prices. Moreover, these processes are now targeted by the Kyoto Protocol since they are energy intensive and they produce significant amounts of CO2 and other pollutants such CO, NOx and SO2. To achieve both a reduction in operating costs (i.e. fuel consumption) and in pollutant emissions while maintaining or improving product quality, one needs to have a very good control of the combustion process."

Jan 1, 2005

By J. K. Afidenyo, J. Osei-Owusu

"The Obuasi Mine of AngloGold Ashanti Limited has been operating the world’s largest Biooxidation Plant at its Sulfide Treatment Plant (STP) in Ghana, using the Gencor Biox® technology since February 1994. The Biox® technology was preferred to other alternative methods of treating refractory sulfide ores such as roasting, pressure oxidation and nitric acid leaching due to among other reasons, its lower capital and operating costs, reduced technical risk, relatively benign environmental impact and its ease of operation and maintenance in a remote location.STP has since commissioning succeeded in operating this technology successfully but not without some operational problems. The Plant has seen a number of upgrades and modifications in its circuits which were motivated by cost, operational and throughput constraints.The objective of this paper is therefore to highlight the mine’s experience in the treatment of its complex carbonaceous refractory sulfide gold ores with emphasis on plant operations and improvements such as the Biox® reactors expansion, flotation concentrate upgrade project and neutralization circuit modifications. The Biox® Plant operating cost is also discussed.INTRODUCTIONThe Obuasi mine forms part of the AngloGold Ashanti Group of Gold Mines. It is located in the Adansi West District of the Republic of Ghana. The mine is primarily an underground operation, although some surface mining still takes place. Ore is processed by two main treatment plants: the Sulfide Treatment Plant (for underground ore) and the Tailings plant (for tailings reclamation operations). A third plant, the Oxide Plant, is used to batch-treat remnant opencast ore and stockpiles, of which there are adequate tonnages to keep the plant operational until 2008.Though reference is made in this paper to the Tailings and Oxide Treatment Plants, the main focus will be on the Sulfide Treatment Plant."

Jan 1, 2008

By S. Dessureault, J. Porter, M. Woodhall

Information and communication technology (ICT) is seen as a key source of future productivity improvements in mines. The information technology infrastructure (ITI) necessary to achieve these productivity improvements will come in the form of data integrated from multiple source systems throughout the mining value chain. Two pure approaches are available: supplier-controlled or operations controlled data structures; each strategy has its own advantages and disadvantages. Case studies involving the South African mining industry are used to demonstrate the advantages of using hybrid-controlled data structures. Depending on the level of operational control, new skills are also necessary to be learnt by mining professionals including: information engineering; creating consistent and quality data; and process improvement techniques that use the integrated data for improving the operation.

Jan 1, 2004

By Kevan J. R. Ford, Chris A. Fleming, Robert D. Henderson

"Kinross Gold Corporation’s Maricunga mine in Chile presents an ideal opportunity to apply the SART process to a heap leach operation. Given increasing levels of cyanide complexed copper in current pregnant solutions from Maricunga heaps (over 300 ppm Cu), there is a need to reduce these levels and decrease cyanide consumption and cost. Additionally, a means of disposing of this copper is required, preferably as a saleable product. The well published SART process applied to gold-copper cyanide solutions was selected as it allows rapid precipitation of cyanide soluble copper as a relatively pure copper sulphide. The process also allows effective recovery and recycle of cyanide back to the heap leach operation.This paper reviews the SART process chemistry and presents a summary of SART bench-scale and pilot plant testwork completed by Kinross. Key design parameters and engineering aspects of the proposed plant at Maricunga are discussed. SART plant operating costs and net revenue analysis are included and illustrate the compelling economics of installing a SART process plant. INTRODUCTIONMaricunga OperationCompañia Minera Maricunga (CMM), fully owned by Kinross Gold Corporation, operates the Maricunga mine (formerly Refugio) which is located 120 km due east of the city of Copiapó at an elevation of 4,200m above sea level in the Andes mountains of northern Chile. Figure 1 shows a map of the location of the Refugio mine relative to other gold and copper mines in the region."

Jan 1, 2008

By F. Bosché

Previous research has shown that ?Scan-vs-BIM? systems are powerful to provide valuable information for tracking structural works (progress, quality, safety). However, the transferability of this capability to other construction areas such as MEP works has not been assessed so far. Comparatively, the construction of MEP systems, in particular pipes and ducts, tends to be more flexible with respect to the positioning of individual components, so that Scan-vs-BIM systems could be defeated when tracking MEP installation works. This paper presents recent results on the feasibility and performance of using a Scan-vs- BIM system to track MEP works. The approach followed is presented and then tested with two real-life challenging case studies were conducted simultaneously but totally independently in Canada and Italy. The results show that, as expected, pipes and ducts tend to be more loosely positioned than structural elements leading to a poorer performance of the Scan-vs-BIM system. Nonetheless, it appears that the system works well to assess the level of conformance of site installation works, providing valuable information for estimating emerging performance metrics like ?percent built as-designed?. In addition, the proposed system could also be useful to accelerate and thus reduce the cost of delivering as-built BIM models for in the case of new builds.

Aug 1, 2013

By Engineering Staff

"This paper briefly describes the surface mining operations at Smoky River Coal Limited (formerly McIntyre Mines Limited, Coal Division) near Grande Cache, Alberta. Geology, mining methods, equipment, manpower and reclamation and environment topics are discussed. Introduction Smoky River Coal Limited, a wholly-owned subsidiary of McIntyre Mines Limited of Calgary, Alberta, produces a high quality, low sulphur, low volatile bituminous coking coal from its minesite located at west central Alberta, approximately 20 km from the town of Grande Cache and 360 km west of Edmonton (Fig. I). Most of the coal property is contained within a 30 km long by 20 km wide block lying in a northwest-southeast direction in mountainous terrain. Elevations vary from 920 m above sea level ·at the plant·site on the Smoky River to 1,600 mat the upper levels of current and proposed mining operations. A total of 11 coal seams have been identified. Only two seams, No. 4 Seam and No. 10 Seam are currently considered of major commercial value. These seams are recovered by both surface and underground mining. Approximately 650Jo of the plant feed coal is obtained from a conventional shovel/truck surface mine; the balance is mined underground by room-andpillar methods. Background In 1921, McIntyre Mines Limited acquired some 26,300 hectares of coal leases at Smoky River. Since then the leases were explored intermittently by different companies including McIntyre. In the mid-l 960s exploration activities increased and several feasibility studies were completed. Development of the area was undertaken by McIntyre in 1968 and, in August of the same year, a long-term contract was signed with a consortium of Japanese steel mills for delivery of 2 x 106 t of clean coking coal for 15 years commencing in 1970. Production was focussed on underground mining, using longwall methods."

Jan 1, 1985

By A. Esterhuizen, S. Essack, H. Joubert, N. Fowler

Tenova Pyromet has developed innovative technologies for copper smelting and electric slag cleaning furnaces. Based on client feedback and requirements, innovative designs have been developed to address key design areas and improve furnace reliability, operability and hygiene. These developments include the NovaLance™ lance system to prevent lance bending on top submerged lance furnaces, the SlagFlo™ slag tapping flow control device to better control bath levels and tapping rate for granulation, and an electrode seal for improved sealing directly onto the electrode casing to allow water-cooled electrode components to be located above the furnace roof. The potential application and benefits of these innovative designs are discussed. INTRODUCTION Tenova Pyromet has a long history in the engineering and supply of innovative electric furnace and related equipment for the base metals and platinum industries. Recently Tenova Pyromet has used its furnace equipment design experience to engineer innovative solutions for top submerged lance (TSL) furnaces, and potentially other furnace technologies. These equipment design solutions are developed to address specific operating challenges and operator requirements. Three of these innovative equipment developments are discussed in this paper. First the NovaLance™ lance technology to prevent lance bending during operation in TSL furnaces, such as used for primary copper smelting, is described. Lance bending has been identified as a significant problem for TSL furnace operators as it causes down time and affects furnace availability. The SlagFlo™ device to control the slag flow rate during tapping has been developed based on specific requirements in the mineral wool industry. The SlagFlo™ device can be used to control slag bath levels in primary smelting, converting and slag cleaning furnaces for base metals including copper. In addition, it can be remotely activated for the safe closing of slag tapholes located upstream from a water granulation system. Finally, Tenova Pyromet developed an electrode seal that seals directly onto an electrode surface. This is a special requirement related to base metals and platinum electric smelting and slag cleaning furnaces where furnace operators prefer to keep the water-cooled electrode equipment above the furnace roof. The seal can be used to seal directly onto the potentially hot and uneven surface of Söderberg, pre-baked and graphite electrodes.

Jan 1, 2019

By R. S. Jones

"Fording Coal Ltd. is now in its fifth year of a 15-year contract to supply 3 million long tons of clean coal per annum to its Japanese steel-making customers. The mine employs both conventional truck-shovel and unconventional ""walking"" dragline coal mining techniques in multiple-seam pits. This paper describes the present and future application of the 60-cu.-yd dragline and truck-shovel pre-stripping fleet in 1•ecovering 5- to 40-footthick coal seams in mountainous terrain. Deep blastholes, coal flow demands, spring ""run-off"", seam and inter-seam thrust faulting, limited seam outcrop data and regional faulting are a few of the problems encountered in this application. The author discusses these problems and their solutions as applied at Fording Coal Ltd."

Jan 1, 1976

By Gavin Ritson, Chris Ward

"The oil sands industry is still fairly young with the first viable oil sand operation having been started in Alberta in 1960. Since then numerous modifications and improvements have been tried and implemented. The current process makes use of high velocity pumping of oil sands slurry with hot water (hydrotransport) to achieve separation of bitumen from the sand.A number of the oil sands processes have been adapted from unit operations that are used in mineral processing, such as crushing, screening, flotation, cycloning and thickening. This paper outlines a typical oil sands process flowsheet and investigates the differences and similarities in technologies and costs to other mineral processing industries. It also considers the very large throughputs required, and presents some of the difficulties and challenges currently faced by the industry as a result of high demand for oil and environmental pressures.INTRODUCTIONOil sands (also known as tar sands) deposits are found throughout the world. The Athabasca Oil Sands deposit in Aberta is the largest of these. Oil sands consist of a mixture of crude bitumen (a semi-solid form of crude oil), silica sand, clay minerals, and water. The Athabasca, Peace River and Cold Lake deposits cover 141,000 square kilometers and contain about 1.7 trillion barrels (270×109 m3) of bitumen in-place, comparable in magnitude to the world's total proven reserves of conventional oil"

Jan 1, 2009

By M. Kreuh

An investigation of the pressure pulse spectrum generated by the gas dispersion processes in a Peirce Smith copper converter was undertaken via the simultaneous measurement of four tuyeres using high frequency pressure transducers. The data was captured, stored, and analyzed using digital data processing techniques; including power spectral density plots, band-pass filtering, and a principal component analysis (PCA). The process was characterized throughout by a dominant 3 Hz pulse signature attributed to the formation of lateral gas envelopes. In particular, test tuyeres in the tuyere line tended to operate synchronously at the dominant frequency, regardless of operating conditions tested and despite being distributed along the converter. Synchronous behavior is thought to arise from the acoustic coupling and possible resonance behavior of the gas delivery system on the converter.

Jan 1, 2007

By Weng Fu, James Vaughan, Stefan Lakemond

Uranium bearing copper sulphide flotation concentrates produced from iron oxide copper gold uranium (IOCG–U) ore contains radionuclides such as 238U, 230Th, 210Pb, 226Ra, 210Po, which have the potential to reduce their marketability, thus posing a challenge to the industry. Thus, a two–stage leach process has been proposed in this study. In first stage, a sulphuric acid leach process effectively dissolve most of the 238U and 230Th into solution, but other radionulclides (mainly 210Pb, 226Ra and 210Po) remain associated with copper sulphide minerals owing to their low solubilities in sulphuric acid solution. In the second leaching stage, the use of methanesulfonic acid (MSA, CH3SO3H) is investigated to selectively dissolve the 210Pb, 226Ra and 210Po from the residue of the first stage. The results indicate that 96% of 238U, 87% of 230Th, 90% of 210Pb, 86% of 226Ra and 17% of 210Po are dissolved using 3 mol/L MSA solution at 90°C for 3 hours, which represents a dramatic decrease in the radioactivity of the copper concentrate. INTRODUCTION Australia is host to one of the largest iron oxide copper–gold–uranium (IOCG–U) deposits in the world. Most of the value in these deposits is associated with copper. In mineral processing, the gangue minerals are separated from copper sulphide minerals that report to a copper flotation concentrate. However, due to the strong association of uranium with copper minerals and hematite, even clean copper concentrates can contain significant amounts of uranium (238U) and its radioactive decay elements, of which thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) are the long life radionuclides. These hazardous radionuclides negatively affect the marketability of the copper concentrates. Customer copper smelters in China, Japan and Europe may consider the radionuclides penalty elements or may not be able to process the feed. Therefore, there is a strong motivation to remove radionuclides from copper concentrates at the mine site before shipping to custom smelters in global market. Hydrometallurgical leaching has been widely employed to remove radionuclides from different kinds of minerals such as copper concentrates (Ragozzini & Sparrow, 1987), zircon concentrates (Aral, Sparrow, McDonald, & Norgate, 2007), and coal ash (Lei, Qi, Sun, Xu, & Wang, 2014). Leaching using sulphuric acid (H2SO4) solutions is the most widely used process for the extraction of uranium from uranium ores due to the relatively low cost and wide availability of the acid (Bhargava et al., 2015; Gilligan & Nikoloski, 2015). The leach process involves treating ground ore slurry with sulphuric acid at elevated temperatures (typically 60–90 °C) under oxidising conditions in order to convert the uranium in the minerals 2+ from the relatively insoluble tetravalent form (UO2) into water–soluble hexavalent state (UO2), which then complexes with SO42- and forms UO2(SO4)22- in solution. The uranium oxidation is generally carried out in the presence of ferric ion (Fe3+), regardless of the reagent and oxidant used. The most commonly used oxidants for uranium include sodium chlorate, pyrolusite and oxygen (Ring, 1980). These oxidants act indirectly by converting ferrous sulphate, formed by the oxidation reaction of UO2 in slurries, into ferric sulphate. The presence of Fe–containing gangue minerals such as hematite in the ore usually provides sufficient Fe required for the oxidation of UO2. After sulphuric acid leaching, the locked thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) elements are chemically liberated from hematite and uranium mineral grains (Ciobanu, Wade, Cook, Schmidt Mumm, & Giles, 2013). However, the extraction rate of radium (226Ra), lead (210Pb), and polonium (210Po) in sulphate solution is very low due to the limited solubilities of (Ra, Pb, Po)SO4 (Bagnall & Freeman, 1956; Liu & Papangelakis, 2006; Nikitin & Tolmachev, 1933).

Jan 1, 2019

By L. A. Melis, J. W. Rowson

"Cluff Mining operates the Phase II uranium mine and mill at Cluff Lake, northern Saskatchewan. During the Phase I operation, uranium tailings were generated by acid leaching of a gravity concentrate and high-grade ore for uranium recovery. The pre-treatment gravity process, as well as the high-grade nature of the ore, led to a concentration of gold in the tailings which justified the installation of a small circuit to recover the contained gold. The operating circuit consists of tailings repulping, grinding, cyanidation, carbon-in-pulp, gold recovery, and cyanide destruction by acidification, volatilization and re-neutralization. The process is described and typical operating parameters are provided. 1.0 INTRODUCTIONCluff Mining, a Saskatchewan partnership, is owned 20 percent by Saskatchewan Mining Development Corporation (SMDC) and 80 percent by Amok Ltd./Ltee. (Amok), manager and operator of the partnership.The current operation includes the Phase II uranium mining and milling facilities, located at Cluff Lake 700 km north of Saskatoon, capable of processing 300,000 tonnes of ore to produce about 4,000,000 lbs. U308 (1500 tonnes of uranium) per year.The Phase I operation was initially established to process the very high grade ""D"" uranium orebody from 1980 to 1983. The leach tailings from the operation Phase I mill operation were found to contain elevated levels of gold. These high gold values were partially due to the gravity pre-concentration step included in the uranium recovery circuit, and to the naturally high levels of gold associated with the uranium mineralization in the ""D"" orebody."

Jan 1, 1988

By J. A. McLennan, J. M. Ortiz

Nickel laterite deposits are typically formed from tropically weathered mafic-to-ultramafic complexes. The resulting nickel concentration is found within soil horizons and is mineable with regular dozer units. At the time of mining, digging elevations are needed at selective mining units (SMUs) or representative dozer regions (RDRs). Moreover, for mine planning, the costs due to dilution and lost ore require mining elevations to be specified. A conditional simulation approach is used to calculate “optimum” RDR mining elevations. Multiple realizations of the ore base surface are simulated. For a single bottom surface realization, dilution and lost ore costs are calculated over the entire vertical extent of each RDR. The optimum mining elevation is the elevation where the lowest summed cost of “accepting dilution” and “wasting ore” occurs. The reported RDR dilution is the cost of mining the volume of waste located below the bottom surface and above the optimum mining elevation. The reported RDR lost ore is the cost of not mining the volume of ore above the bottom surface and below the optimum mining elevation. For all ore bottom surface realizations, optimum RDR mining elevations and their associated dilution and lost ore costs are calculated and compiled to represent production uncertainty.

Jan 1, 2006

By Michael B. Cortie

Mesoporous gold sponge has the unique property of being both metallic and highly resistant to oxidation. It has potential application in catalysis, in bio-sensors, in optical coatings, in analytical chemistry and, as we show here, as the basis for a new kind of ultra-capacitor. Due to the cost of gold, the most probable niche for a gold-based ultra-capacitor would be in the high-power/high-energy regime, a region where gold would compete with devices based on RuO2. A high internal resistance limits the power that can be usefully drawn from existing carbon-based ultra-capacitors, and that this problem can potentially be overcome by gold-based devices. A simple proof-of-concept ultra-capacitor based on mesoporous gold is described and its behaviour during charge and discharge cycles examined. In this work a step change in the input or output voltage of the device was used as the controlling parameter. There was also a residual faradaic current resulting from traces of undissolved aluminium left over from the AuAl2 precursor used to make the sponge, and some charge storage due to polarization of the solution. Deconvolution of these three effects was not entirely accomplished, but an ostensible capacitance of about 7 to 14 mF/g Au was demonstrated. Further improvement from these early results seems likely.

Oct 1, 2003