Search Documents

By M. England

Test equipment has been developed to record automatically both the displacement of the pile head and the load applied during a conventional maintained load pile test. Some systems also have, in addition, been fitted with the facility for maintaining the applied load, as set by the operator, at very constant levels. The advantages are both commercial and technical, but a well trained operator has to be in attendance to control the test. Since typical test specifications in the UK require more than 19 hours to complete, it became inevitable that at least one equipment operator remained on site to expedite the test for its duration. Although electronic measurement and data logging of load tests may be more safe than previous direct observation of dial gauges. A single person remaining on a construction site alone is not to be recommended, even if they are just supervising the test. Further development of the testing system produced equipment which will perform the entire test specification as required without operator intervention. To achieve this, full automation is employed. The patented method particularly addresses the safety requirements and by using additional sensors, detects any uncharacteristic behaviour of the pile under test or of the reaction system and the equipment takes appropriate action in a controlled and safe manner. The quality of test data returned from these automated systems is a key element when analysing pile behaviour with models such as CEMSOLVE? and TIMESETTM. These analysis methods often indicate ground disturbance resulting from installation technique and have allowed pile design to be optimised using actual field data rather than theoretical considerations alone. An additional feature is remote access, this allows the data recorded to be transferred and the progress of the test to be viewed from practically any location. This permits experts to view the data 'live' and allows rapid diagnosis of any problems with the expected pile behaviour.

Jan 1, 2002

By Steve Thoman

After the 1989 Loma Prieta Earthquake, the California Department of Transportation (Caltrans) initiated an overview of the Caltrans Bridge Design Specifications (BDS) and bridge seismic design practice in California. This overview is continuing under the direction of the Applied Technologies Council (ATC-32), to review and revise as necessary existing standards, performance criteria, specifications, and practices for design and construction of new bridge structures within California. The ATC-32 project began in August 1991 and is expected to be completed in 1995. Since 1990, Caltrans project-specific seismic criteria have been developed and implemented on the I-280 and I-480 projects in San Francisco. Caltrans and an independent seismic safety review panel continue to develop and implement these criteria on other projects. In 1991 and 1992, project-specific seismic criteria were used on the I-880 reconstruction project in Oakland. The seismic safety review panel considered the I-880 seismic design criteria a state-of-the-art methodology to ensure seismic safety against collapse of bridge structures subjected to a maximum credible seismic event. This paper highlights the 1992 "I-880 Reconstruction Project Seismic Design Criteria Review" report prepared by the Seismic Safety Review Panel and Caltrans Division of Structures and will compare pre-1989 BDS and AASHTO methodologies to the I-880 criteria.

Jan 1, 1996

By B. Ladanyi

The design philosophies for piles in unfrozen and frozen soils are compared, and their similarities and differences are underlined. It is shown that in frozen soils, the long term behavior of a pile is difficult to predict, because of inadequate knowledge on the behavior of adfreeze bond with time, and on the value and variation of the lateral normal stress acting on the pile. Both of these problems are discussed in the paper on the basis of laboratory tests and theoretical analyses.

Jan 1, 2010

By Charles M. Wilk, Lori Tiefenthaler

"Information presented in this paper can be used to support deep soil mixing, subsurface grouting and slurry wall technology as sustainable construction technologies. Ordinary Portland Cement (OPC) is the default cementitious material used by Deep Foundation Institute (DFI) Members for geotechnical work. Owners, engineers and contractors can contribute to the sustainability of a geotechnical project by increasing the use blended hydraulic cements and industrial byproducts to replace some of the OPC in mix designs. Sustainability is defined as the quality of not being harmful to the environment or depleting natural resources. Production of cementitious materials consumes natural raw materials and energy while also generating air emissions and waste. Life Cycle Assessments can be used to compare the relative environmental impacts of one cementitious material to another. Blended hydraulic cements (BHCs) are interground (or blended) mixtures of Supplementary Cementitious Materials (SCMs) with OPC. Commonly used SCMs include fly ash, ground granulated blast furnace slag (GGBFS) and limestone. Examples of industrial byproducts commonly used in geotechnical work include coal combustion residuals (CCR) (aka fly ash), and ground granulated blast furnace slag (GGBFS). Much of life cycle impact of these SCMs and industrial byproducts have already been borne by the industries that generated them. There is increasing awareness to LCA and sustainability of different materials used on projects. This is evident in the application of the Leadership in Energy and Environmental Design (LEED) program. The savings in environmental impact with the use of SCMs and industrial byproducts can make proposed use of these materials in a geotechnical project more attractive in terms of sustainability. This paper presents (a) information that compares published life cycle assessment data of OPC, BHCs, and slag cement (SC) to illustrate the potential benefits to sustainability and (b) general strategies for positioning a geotechnical application, use, project design or cementitious material mix as a more sustainable alternative"

Jan 1, 2017

By Joan Stoupa

The expansion of the West Point wastewater treatment plant located in Seattle, Washington, will require a permanent tieback retaining wall to enlarge the plant site for the new treatment plant facili­ties. The retaining wall will extend approximately 3,000 feet along the property boundary between the treatment plant and the neighboring Discovery Park. Wall heights will range from 35 to as high as 65 feet. The purpose of the retaining wall is to provide a more uniform grade on the plant site and to resist lateral pressures exerted by the upslope, unstable hillside. During preliminary design of the retaining wall, various wall systems were evaluated based on assumed subsurface soil conditions. Results of preliminary studies indicated that expected subsurface conditions and wall heights made a permanent tieback retaining wall feasible. However, uncertain loads on the wall and the capacity of anchors in the native soils were significant. As a result, a detailed geotechnical program was conducted. The scope of the program included conventional drilling, sampling, analyses, and a field test program to determine site-specific anchor capacities. This paper describes the anchor test program and results.

Jan 1, 1990

By George J. Tamara

The urban environment presents special challenges for the design and construction of earth retention systems. Complications arising from difficult subsurface conditions are compounded by the presence of urban infrastructure and existing and prior construction. The proximity of adjacent structures as well as intense prior use can cause special concerns including the potential for archeological artifacts or contaminated ground or ground water. Utilities and structures may be particularly vulnerable to the effects of ground movement, dewatering and vibrations. Difficulty of access, congestion and limited work areas may severely restrict means and methods of construction. Dewatering may be limited or prohibited because of concerns for disposal of clean or contaminated water, depletion of aquifers, drawing of contaminants to the site or dewatering induced settlements.

Jan 1, 2003

By G. X. Zeng

A calculation programme of finite element method has been developed in order to study the behavior of excavation with sheet piling in soft clay. Based on a series of isotropically consolidated-undrained tests (CIU) on Hangzhou clay a linear relationship between the normalized initial tangent modulus number, E1, and stress-path parameter, a, is found for four different stress paths, and stress-path dependent modulus equations derived. Meanwhile, several influence factors, such as embedment depth and stiffness of the wall and soil conditions, were taken into consideration in the programme. Some valuable conclusions were obtained. Finally, a case history was studied by the proposed method of calculation. The result of calculation and the field observation are in good agreement.

Jan 1, 2010

By Min Sunn Ye, Wei Wang, Huawen Xiao, Kai Yao, Fook Hou Lee, Siang Huat Goh

"Previous research have shown that introducing fibers to cement soil mixture is effective in improving the ductility as well as maintaining the strength of cement-treated soil. A good knowledge of stiffness of the improved soil at small strain is essential for realistic predictions of ground movements that may affect adjacent buildings or underlying infrastructure. This paper presents a triaxial system with local strain measurement developed for studying shear modulus degradation of cement treated clay with fibers. Cylinder specimens (70mm diameter by 140mm height) with 50% cement, 100% water, 0% to 1% polypropylene fibers by mass, and 7 days of curing period were used. A local strain measurement system with floating type miniature submersible LVDT is introduced in this paper. Configuration of the mounts including the pin size, length and distance are presented and discussed. Based on the experimental results, a reasonable configuration of the mounts is recommended for fiber reinforced cement treated clay. Results showed that the proposed local strain measurement system is effective for testing the shear modulus degradation of cement treated clay with fibers under both unconfined and confined condition. Comparisons with results from resonant column and bender element tests served to verify the reliability of the local strain measurements using the proposed method.INTRODUCTIONIn many geotechnical engineering problems, the operational strain domain ranges from 10-3% to 10- 1%. A good knowledge of stiffness at small strains is essential for realistic predictions of the ground movements that may affect adjacent buildings or underlying infrastructure. As such, during the last 3 to 4 decades, the importance of using the small strain stiffness of soils for the design of foundation and underground structures has widely been accepted. Triaxial testing has been widely used to study the stress-strain behavior of soil in the laboratory. However, the stiffness obtained from the conventional triaxial apparatus is usually far smaller than those back-calculated from field measurements. This is mainly attributed to the overestimation of axial strains from the external strain measurements, which usually includes compliance effects of the loading and load measuring system as well as sitting, bedding and alignment errors between sample and system (Baldi et al., 1988). The poor resolution of the external strain measurements is another important contribution. Therefore, conventional procedures are inappropriate for small-strain stiffness evaluation due to low accuracy and resolution."

Jan 1, 1900

By H. Meseck

The new building of the Central Bank of Iraq in Baghdad was footed in difficult underground conditions on more than 600 reinforced concrete driven piles, with cross-sectional diameters of 45 x 45 cm and pile lengths of 12.0 to 18.0 m. The necessary embedded depth and the bearing capacity thus reached were established on all 600 drives piles by means of dynamic pile tests. For the calibration of the dynamic pile tests, 6 static pile load tests were carried out. The execution of the construction and the results of the extensive tests on the building site are shown.

Jan 1, 1989

By Bengt H. Fellenius

Session 2, Deep Foundation without Soil Excavation, has attracted no fewer than 22 papers dealing with subjects from soil improvement by grouting, injection, and deep mixing techniques through vibroflotation and special piles, including aspects pertaining to conventional driven and bored piles. In the short time available, it is not possible to both do justice to the papers and provide a critical review of the state-of-the-art. Instead, to meet the objective of making the next half hour worthwhile to the audience, I have chosen to comment on a few special points brought forward in the papers and thereafter to discuss more in detail a couple of aspects I have deemed to be of general interest. Four papers deal with jet-grouting, injection, and deep mixing techniques: DOMSKI, J. J. Reinforcement of subsoil under the foundations of historical buildings in Cracow using deep injection technique. RESTELLI, A. B, BERTERO, M., and LODIGIANI, E. Deep mixing technology to improve the bearing capacity of a very soft clayey soil under an earth embankment.

Jan 1, 1994

By Brian Maroney

In this paper an overview of the California Department of Transportation's (CALTRANS) bridge design criteria is presented. Special emphasis is focused upon seismic design and retrofit criteria. Topics include earthquake load definitions, foundation and structure type selection, structural earthquake analysis, and structure behavioral requirements.

Jan 1, 1993

By Kazimierz Gwizdala

In the paper the method for estimation of settlement of vertically loaded piles in a group is presented. The method is generally based on the hybrid procedure with non-linear solution for single piles and with interaction between them for the low-strain shear modulus. Some attention is paid to the influence of deformation and strength parameters used in calculations. The applied model is verified in the framework of the research programme carried out recently in the Geotechnical Department of Gdansk Technical University. It concerns monitoring and analysing the settlements of the existing structures on piles. A comparison of calculation and measurements results for two tested buildings is presented as an example.

Jan 1, 2002

By James P. Stewart

This case history describes the engineering design and construction for the Contractor of a 35-ft-deep excavation for an 800-square-foot addition to an existing sewage pump station. The site posed unexpected geotechnical complications that included deep gravelly soil, a history of local construction difficulties, groundwater consisting of heavy salt brine, and the need to underpin the existing pump station. The project took an interesting twist when the Owner issued a change order limiting the dewatering discharge to a fraction of that required to lower the water table. This documents the interesting circumstances of this job and documents the unusual subsurface conditions in the Syracuse, NY Lakefront area.

Jan 1, 2003

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid shoring system consisting of cast-in-place soldier piles with Cutter Soil Mixing (CSM) infill panels was constructed for temporary support of a 19.8 m (65 ft) deep excavation in Vancouver, British Columbia, Canada. Deep Mixing (DM) was completed up to 9.7 m (32 ft) in fill, peat, wood waste and clayey silt with embedment in dense till, and soldier piles constructed through the dense till extending to below final excavation level. Two trial CSM panels were installed ahead of production to assist with developing the termination criteria of the CSM panels in the dense till. The constructed depth of the CSM panels was based on interpretation of real-time monitoring data obtained through the Bauer B-tronic system. Inclinometer monitoring data from two CSM panels and two soldier piles, as well as soldier pile survey target data was used to assess and monitor the performance of the hybrid shoring system throughout bulk excavation. The objectives of this paper are to provide an overview of the design and construction aspects of the hybrid DM shoring system and to present inclinometer and pile target data to demonstrate the lateral performance of the CSM infill panels and soldier piles. This paper also discusses the merits of using real-time monitoring data as part of the engineering decision-making process for validating CSM panel construction. BACKGROUND A hybrid DM shoring design was recently completed for a high-rise development in downtown Vancouver, British Columbia for temporary support of a five level basement excavation. Deep mixing was proposed by the excavation and shoring design-build team as the preferred method to construct infill panels between soldier piles because of the speed at which the shoring system could be constructed in variable fill, peat, wood waste and overburden compared with traditional secant piling methods. The development site is generally a truncated triangle in plan, with the longest side of the triangle being approximately 115.7 m (380 ft) long and the two shorter sides being approximately 71.6 m (235 ft) (Hybrid Shoring Wall 1) to 75.0 m (246 ft) (Hybrid Shoring Wall 2) long. The site is bounded by an existing bridge off-ramp structure along its longest side, and by city streets on the other two sides, as shown in Figure 1. The truncated section is approximately 16.8 m (55 ft) (Hybrid Shoring Wall 3) long. Due to project constraints, the hybrid DM and soldier pile shoring system was only proposed for the two shorter sides of the triangle and the truncated section. Traditional secant piles were installed for the longest side. This paper focusses on the hybrid shoring system. A typical detail showing the CSM infill panel with the soldier piles is presented in Figure 2."

Jan 1, 2017

By J. Brian Anderson

Jointed micropiles were investigated to support bridge foundations where shallow rock was present. In this application, micropiles would have some amount of unsupported length, and would be subject to nominal lateral loads. Five lateral load tests were conducted on micropiles to demonstrate the impact of casing joints and rock socket embedment on lateral behavior. Load tests were simulated with FB-Multipier, a hybrid-finite element program for analysis of deep foundations, for proper design of the loading apparatus and instrumentation. The micropile sections were 2 m (6.56 ft) long, 273 mm (10.75 in) in diameter, 13 mm (0.5 in) thick walled, with a 50-mm (2-in) long threaded joint. Micropiles were made of one to three casing sections and were embedded 0.3, 0.6, 1.5, or 3.0 m (1, 2, 5, or 10 ft) into rock. In each test, two identical micropiles were pulled together using a simple frame until the weaker pile failed. All micropiles were instrumented with inclinometer casings while two contained strain gages at 0.76 m (2.5 ft) intervals. Load and displacement were measured at the pile heads. Tests showed the embedment of 0.6 m, 1.5 m, and 3.0 m (2 ft, 5 ft and 10 ft) sufficiently carried lateral loads over 180 kN (20 tons). The piles embedded 0.3 m (1 ft) were not able to maintain lateral load. In general, all micropiles tested to failure exhibited a brittle failure mode where there is small lateral deflection followed by a sudden failure at the casing joint. This was demonstrated in three of the load tests. In most cases, the micropiles were stiffer and stronger in the load tests than originally predicted numerically. The final test, where piles were not loaded to failure, verified that embedding vibrating wire rebar strain meters in the grout captured the bending moment profile of the micropile. The results showed the maximum moment in this case being carried directly across the threaded joint as predicted by the preliminary models. The results of these tests were used to calibrate the FB-Multipier numerical model. Using a load test that included bending strain measurements for a match, the soil properties were adjusted to produce reasonable matches for all of the load tests.

Jan 1, 2011

By Stephen T. Young

The construction of Phase 2 of Hong Kong Station, its retail podium and International Finance Centre Two, the tallest building in Hong Kong, will be completed in the middle of 2003. This paper describes the design and construction of the slurry wall for the Station (both Phase 1 and Phase 2) and the two commercial buildings at the Station. The slurry wall is used as the permanent earth support wall for the station box and the excavation depth ranges from 70 feet to 120 feet. Top-down construction technique was adopted to support the excavation of the station, while circular cofferdams relying on hoop stiffness were constructed to support the basement excavation of the two towers. The designed behavior of the slurry wall is also compared to the as built behavior.

Jan 1, 2003

By Stephan Großwig, Karolina Nycz, Arne Kindler

"Commonly used anchor monitoring systems are mainly based on the use of anchor force meters. However, experience shows that the reliability of the display of force meters lowers over time. Other measurement and test methods like for example fibre bragg grating method require a comparison with an unloaded optical fibre and give only selective information about the bearing behavior. Moreover the obtained information has to be interpreted. In the following article, first measuring results of an anchor monitoring system based on measurements with optical fibre are presented. The new monitoring system is based on the Rayleigh technology and was used to test the load bearing behavior of the anchor grout body as well as for the evaluation of the grout body condition in concrete-damaging groundwater.INTRODUCTIONThe first fibre optic sensors came onto the market about three decades ago. Initially used as special solutions only in selected cases, now they have found use in almost all areas of technology, especially in areas, where electrical sensor systems reach their limits. The first application examples of spatially resolved fibre-optic sensors in the field of geotechnics have been in existence since the mid-1990s, in projects such as the assessment of the of radioactive repository location sites (Hurtig et al. 1994), for the monitoring of landfill sealing systems (Hurtig et al. 1995) or within the framework of the rehabilitation of mountain farming landscapes (Schreck et al. 1998).The company's first own works in the field of glass fibre measurement technology have been in existence since 1993. The first carried out projects were a monitoring at the Edertalsperre (Dietz et al. 2001), a monitoring with glass fibre tendon at a flood bridge in Carinthia as well as monitoring within the framework of the Storebælt crossing. In all cases, the structure was permanently monitored by means of individual-point measurements. Since 1993 various fibre-optic sensor solutions for geotechnical applications have been introduced to the market (Voet, Glötzl 1996, Hurtig et al. 1994)."

Jan 1, 2017

By Richard K. Sandaas

Start Date: April 4, 1988 Completion Date: Dec. 29, 1989 Contractor: SCI Contractors Past and present transportation centers will come together at International District Station, located at the south entrance to the tunnel next to the turn-of-the-century Union Station train depot. The area will bustle once again with activity as commuters and visitors converge on the modern transit station at the edge of Seattle's International District. Buses coming from south Interstate 5 and Interstate 90 will enter the tunnel through this station. [ ] International District Station is an open-air station, 1,060 feet long and 82 feet wide (about 15,400 cubic yards of concrete were used to build the station). A concrete lid over the southern portion of the station staging area is held in place by 131 support piles. The station will include entrances on Jackson Street and King Street. Union Pacific Realty is planning to build an office and retail complex upon the lid. The station also has an international flair. Symbols of the Chinese zodiac will be etched into the station plaza floor. The station platform walls will be lined with large steel panels embellished with designs in origami?a Japanese folded paper art form. [ ]

Jan 1, 1990

By John Wise

Significant movement to an existing slurry wall which serves as a retaining wall on 'O' Street in Southeast Washington, D.C. initiated the Department of Public Works for the District of Columbia to invite specialty contractors to propose a rehabilitation and stabilization for the failed slurry wall. Nicholson Construction Company proposed and was awarded a contract for the construction of an anchored precast lagging and soldier pile wall to be located approximately 4 feet in front of the existing structure with granular fill placed between the new and existing walls. Stabilization of the existing slurry wall also included drilling horizontal weep holes and demolishing the failed panels down to the existing ground surface. A new and improved drainage system was also constructed to increase the amount of water directed toward the existing storm sewer system running along 'O' Street. This paper provides a detailed account of these construction activities.

Jan 1, 2003

By Fabio Santillán, Mario Mauro, Raffaella Granata

"This paper presents the utilization of slurry walls methods for the recent remediation of three high hazard active dams in the United States. Tuttle Creek Dam, located in Manhattan, KS, required seismic retrofit. To this extent, transverse shear walls were installed on the downstream slope using self-hardening slurry (SHS) to reinforce the liquefiable foundation soils. Herbert Hoover Dike, located around Lake Okeechobee, FL, is subject to potential failure because of internal erosion, piping and slope instability at high water levels. The innovative use of the hydromill equipment with SHS allowed the successful construction of the cutoff wall through heterogeneous soils and rock. At Bolivar Dam, located in Bolivar, OH, under-seepage negatively affects the structural stability of the dam, and a partial seepage barrier wall is required through the upstream slope of the dam. In this case, the Contractor selected the plastic concrete seepage barrier, excavated by a combination of clamshell and hydromill equipment. The main features of the three projects are summarized in Table 1. IntroductionTuttle Creek Dam was constructed by the U.S. Army Corp of Engineers (USACE) on the Big Blue River in North-East Kansas in the 1950s for flood control. Tuttle Creek Dam is a zoned earthfill embankment, 7,500 ft long and about 137 ft high with a crest width of 50 ft (Fig. 1). It is located in an area of moderate seismicity associated with an old continental rift zone located just to the east of the dam. The USACE, under the Dam Safety and Assurance Program, determined the need for remediation. Site investigations and geotechnical analyses identified the upper alluvial foundation sands as being susceptible to liquefaction when subjected to the Maximum Credible Earthquake.In 2005, USACE awarded a construction-manager-at-risk/early Contractor involvement contract. The USACE and the Contractor closely cooperated to identify the most effective technologies, materials and configurations to be used in the remediation. The original remediation design required both the upstream and downstream slope stabilization of liquefiable foundation. Results of refined seismic deformation analyses revealed that the stabilization of the downstream slope and toe was needed to protect the downstream seepage control system and to provide assurance that a liquefaction-induced flow slide would not occur (Stark et al., 2012)."

Jan 1, 2016