Search Documents

By Lenin T., Madhav M. R., Padmavathi V.

Use of PVDs and preloading on the ground can significantly reduce the time taken for ground to consolidate. Many soils in situ are lightly overconsolidated, with overconsolidation ratios (OCR) ranging from 1.0 to 2.0 due to various reasons such as glaciation, ground water level fluctuation, aging, cyclic loading, creep, erosion, cementation, etc. The effects of overconsolidation ratio are analysed in this study. Compression index and consolidation coefficient are important parameters in determining time – settlement response of soft soils under preloading and with PVDs. These parameters are typically estimated using oedometer tests on samples, with the assumption that the results represent the entire deposit. The in-situ time-settlement plots at different depths are used in the back analysis for estimating compressibility and consolidation parameters of in situ ground, resulting in more representative values that reflect the deposit's overall behavior. From observed time versus settlements plots, variations of compression index and coefficient of consolidation with depth of a deposit are presented. Estimation of compression index with depth is possible based on different OCR values as shown in this study. Barron (1948), Asaoka methods are used to estimate the coefficient of consolidation with flow in the radial direction.

Sep 1, 2022

By Pratik Goel, Sumanta Haldar

High-speed rail is an emerging area of interest in India. The Government of India is implementing prestigious bullet train projects in various parts of the country. High-speed rail (HSR) will be operating in India at about 320 kmph at an elevated track on a viaduct for most of the ongoing and upcoming corridors. High-speed projects in India necessitate an indigenous solution for design applications for viaduct design. Pile groups are extensively used in viaducts for high-speed trains, as they can be a settlement reducer and increase the bearing capacity. Post-construction settlement of pile foundation for high-speed railway viaduct is a concern of engineers. Limited attention has been paid to estimating the post-construction settlement. This paper aims to propose a prediction of the cumulative settlement of pile groups due to cyclic train loading. A three-dimensional finite element model (3D-FEM) of the pile group is established in Abaqus CAE. A suitable plastic model is used to simulate the subsoil. The pile group is modelled as an isotropic-elastic element. The study examines the influence of cyclic loading time and train speed on the settlement of the pile group. The analysis is carried out considering various single pile and pile group parameters like S/D, Ep/Es, L/D, Pile cap thickness, etc. and finally, an optimum configuration is suggested.

Sep 1, 2022

By Suzanne R. Hess-Brittelle, Sharon L. Schulz, Tyler J. Quick, Amy F. Ebnet

"Abiquiu Dam is a rolled earth fill dam with impermeable core located on the Rio Chama in New Mexico. Abiquiu has had a history of excessive seepage through the fractured sandstone abutments since water was first impounded in 1963. The foundation was treated with a single row grout curtain in the cutoff trench prior to placement of the embankment. During the 1960’s and 1970’s, the grout curtain was extended 1,000 ft. into both abutments and sections of the foundation beneath the embankment were regrouted. Grouting of the foundation beneath the embankment required drilling through the embankment. Drilling fluid loss or loss of circulation within the impervious core was observed during multiple phases of supplementary grouting and during verification drilling following the 1970’s grouting program. It is likely that the drilling methods employed for these grouting and drilling programs caused hydraulic fracturing of the impervious core. The fluid losses in the embankment may be related to seasonal shutdown layers in the embankment or benches in the abutment foundations. In addition, it is likely that the impervious core was fractured from grout pressures during installation of grout pipe through the embankment.INTRODUCTIONAbiquiu Dam is located on the Rio Chama in New Mexico and consists of a rolled earth fill dam with impermeable core, controlled outlet works, and an uncontrolled rock-cut spillway. The dam was authorized for flood control and sediment retention and was designed as a dry dam, holding flood pools for relatively short durations. The foundation is comprised of Permian and Triassic age, interbedded mudstones and sandstones that were deposited in an active braided stream system. Sandstones are moderately fractured and have variable aperture and infilling. Generally speaking, joints are near vertical. Abiquiu has had a history of excessive seepage through the fractured sandstone abutments since water was first impounded in 1963. The foundation was treated with a single row grout curtain in the cutoff trench prior to placement of the embankment. In 1966-1968, the grout curtain was extended 500-ft into the left abutment and the foundation beneath a 560 ft. section of the embankment was re-grouted. In 1978-1980, the grout curtain was extended 1,000 ft. into the right abutment, an additional 500 ft into the left abutment and the foundation beneath the right 520-ft section of the embankment was re-grouted. The alignments of these grout programs are shown in Figure 1. Grouting of the foundation beneath the embankment required drilling through the embankment. Drilling fluid loss or loss of circulation within the impervious core was observed during both phases of supplementary grouting and during verification drilling following the 1978-80 grouting program. It is likely that the drilling methods employed for these grouting and drilling programs caused hydraulic fracturing of the impervious core. In addition, it is likely that the impervious core was fractured from grout pressures during installation of grout pipe through the embankment. This paper provides a summary of the drilling and grouting methods used during these programs and the potential for damage to the embankment."

Jan 1, 2016

By Sailesh S. Author

The current design method for soil-cement (SC) columns improved soft clayey ground under the highway embankments assumes a slip circle failure surface shearing through the columns and the soils using a weighted average shear strength. However, the results from the laboratory centrifuge model test and numerical analysis indicate that in many cases, the SC columns fail by bending. Some researchers have proposed methods for estimating the maximum embankment loading for bending failure of SC columns, but those methods have limitations in correctly considering the internal shear stresses or not applicable for the group SC column improvement. Numerous model embankments on SC columns have been simulated by three-dimensional (3D) finite element analysis (FEA) and the mechanism of bending failure and the magnitude of the bending moment in the SC columns under embankment load has been investigated. Based on the simulated results, the design method for the estimation of the bending failure of floating SC columns has been proposed. The predicted results from the proposed method agreed with the existing field condition of one embankment in Saga, Japan reported in the literature in terms of the stability of columns. Hence the proposed method can be used for the design of floating SC columns in the soft ground.

By Satyajit A. Vaidya

This paper presents a case-study in the design and construction of deep foundation element supported mats for two residential towers on an18,000-square-foot site in Brooklyn, New York. Based on site sub-surface conditions, conventional mat foundations bearing on medium dense sand, having an allowable bearing capacity of 3 tsf, were originally anticipated for the 16 and 25-story towers. However, when the tower shear walls were relocated to the edges of the mat foundations due to architectural revisions, the significantly increased mat edge contact stresses applied to the soil subgrade resulted in calculated settlements of a magnitude that would adversely impact the proposed structures and the neighboring/bordering lot-line building and rail transit subway structures. To address this issue, deep foundation element supported mats were designed for the towers. The design was performed as an iterative process involving structural SAFE and geotechnical Plaxis finite element computer analysis to develop a coordinated geo-structural model of the foundation system. Initial presumptive design values of 45 pci and 445 kips/inch were used for the modulus of subgrade reaction and minimum deep foundation element stiffness, respectively. The designed foundation system consisted of 40 and 60-inch-thick mat foundations for the 16 and 25 story towers, respectively. Initially, the deep foundation elements were designed as 50-foot-long, 14-inch-diameter elements installed to sustain a maximum individual compressive load of 250 tons. The final deep foundation element design was subsequently refined to consist of a 48-foot-long, drilled and grouted IBO Titan 103/51 element designed to sustain a maximum load of 167 tons. Subsequent field load tests on the deep foundation elements confirmed element stiffness ranging from 1,040 to 1,530 kips/inch, with measured mobilized side shear of about 29 psi. The mat foundation reinforcement was adjusted for the pile stiffness values determined in the field load tests, and the deep foundation supported mats were constructed. The two towers were subsequently constructed, and have performed successfully.

Jan 1, 2010

By Lance A. Roberts

The Federal Highway Administration (FHWA) has mandated the use of the AASHTO Load and Resistance Factor Design (LRFD) specifications for all new federally-funded transportation infrastructure projects beginning in October 2007. This includes the design of all geotechnical-related elements, such as deep foundations, which have historically been excluded from the LRFD requirements. The basis of the LRFD specifications is the application of a probabilistically computed parameter called a resistance factor to the foundation capacity in lieu of the traditional, and often arbitrary, factor of safety. Therefore, the process of computing resistance factors for use in the design of deep foundations is extremely critical to ensure a safe, efficient, and consistent design methodology. In this paper, various methods to calibrate resistance factors for use in the design of deep foundations are examined. The methods that are currently utilized to calibrate the resistance factors reported in the AASHTO LRFD specifications may be classified as the allowable stress design (ASD) method and the reliability theory calibration method using static capacity prediction techniques. These methods are compared to a ?t-z? model design methodology. The current methods focus exclusively on the strength limit state design of deep foundations. The advantage of the ?t-z? model methodology is that it can be utilized for both strength and service limit state design. In addition, the results show that resistance factors vary based on geological setting, construction method, failure criteria and deep foundation type. This variability in the resistance factors should therefore be integrated in the design to ensure that the objectives of the LRFD approach are satisfied.

Jan 1, 2008

By Konstantin G. Ashkinadze

The paper considers performance of piles supporting transient pipe anchors in heavy industrial pipelines. Events such as pump trips or opening and closing of large valves produce short-term dynamic pulses in the pipeline with variable spectral characteristics. Their magnitude is large enough to cause major damage to the pipeline and its anchors, which face horizontal impact loads amounting to hundreds of kN. Design of pile foundations supporting these anchors is often governed by limitation of deflection of the support to prevent overstressing pipeline connections and equipment nozzles. The maximum deflection does not always correspond to the largest load because the stiffness of the soil surrounding the piles heavily depends on the rate of loading. Faster actions encounter stiffer soil response while loads of smaller magnitude applied slowly may be more critical for the deflection time history of the anchor. A typical transient action has both high- and low-frequency harmonics, which makes the response complex. Using load rate-dependent p-y curves published in literature, the paper develops methods of analysis of pile foundations for transient anchors. Pile displacement amplitude – input frequency – natural frequency correlations and time histories of pile response are constructed for typical profiles of transient actions, considering nonlinear soil response to large horizontal loads.

Jan 1, 2016

By Danielle Nhanqulumanga, Pranith Bhatt, Snehal Patel, Khadeeja Priyan

The Bi-Directional Static Load Test (BDSLT) is a test that determines the capacity of piles when loaded under bi-axial static compression. In recent years the BDSLT has seen an increase in demand due to its safety, speed, and affordability. This innovative foundation testing method has been universally used over the last 50 years, however respective codes and standards have only been published within the recent years. Detailed test procedures and methodology are expatiated in the ASTM D8169 M-18 [1], and the IRC 78 2014 Clause 709.2.5. [2] These standards provide the minimum requirements for the execution of the BDSLT. In this paper we did a comparative study of both standards envisaging to bring attention to the similarities and discrepancies found therein, with an aim to highlight the impacts and challenges that differing provisions of each standard could pose on the conduct of the BDSLT. Discrepancies found have been explained on the basis of geotechnical engineering theories and relevant field occurrences observed by superior engineers. Additionally, we emphasize on the relevance of experienced engineer’s judgement when utilizing the standards.

Sep 1, 2022

By Bidjan Ghahreman

A total of 120 micropiles were constructed for foundations of a new selective catalytic reduction (SCR) unit in a coal-fired power plant east of Kansas City, Missouri. Construction was performed under restricted overhead conditions because of the existing facilities. The subsurface profile included about 70 feet of overburden composed of granular fill, stiff to very stiff cohesive material, medium dense sand, and very dense gravel. The bedrock was composed of alternating layers of shale and claystone (weak rock) and limestone (strong rock). It was decided that the bond zone would be entirely in the bedrock. The design rock profile along the bond zone was composed of 10 feet of shale and claystone underlain by 10 feet of limestone, which in turn was underlain by shale and claystone. To achieve the design compression and uplift capacities of 100 tons and 60 tons, respectively, a length of 23 feet was determined for the bond zone. Compression and uplift load tests were performed to verify the design. IBC-2000 elastic line, Decourt (1999) extrapolation, and Chin-Kondner extrapolation were used to interpret the load test results. The interpretation of load test data indicated that both compression and uplift capacities far exceeded the respective design loads. Spring constants of 397 tons per inch (T/in.) (in compression) and 290 T/in. (in uplift) were estimated from load tests at respective design loads. During the compression load test, no sign of creep was observed after the applied load was maintained at the design load (100 tons) for two hours.

Jan 1, 2009

By Tracy Brettmann, Melis Sutman, C. Guney Olgen

"The use of energy piles for geothermal heat exchange has been steadily increasing during the last decade, yet there are still pending questions on their behavior during temperature changes. This paper focuses on the thermo-mechanical response of three full-scale energy piles installed in Richmond, TX. The behavior of test piles subjected to thermo-mechanical loadings was studied in situ with the aim of quantifying the thermal influence on the performance and capacity of energy piles. An extensive field test program, including conventional pile loading tests and application of heating-cooling cycles was conducted on the test piles during a period of six weeks. For thermal load applications, the heat exchanger fluid with maximum temperature of 113°F (45°C) and minimum of 47°F (8°C) was circulated in the geothermal loops placed at the center of the test piles. Optical fiber sensors, vibrating wire strain gages, thermistors and thermal integrity profile wires were installed to monitor the strain and temperature variations along the energy piles throughout the field tests. The strain and temperature profiles during heating-cooling cycles on the test piles under static loads and without a maintained load were monitored to investigate the effect of thermo-mechanical and pure thermal loads on the energy piles, respectively. Conventional pile load tests were applied before and after the application of thermal cycles. The results of the pile load tests are compared to evaluate the effect of temperature cycles on pile capacity.IntroductionEnergy piles are deep foundation elements designed to access and exploit the relatively constant temperature of the ground and its heat storage capacity for efficient heating and cooling of buildings. The deep foundation elements that are already in place for structural support are integrated with adsorber pipes to perform as heat exchangers connected to ground source heat pump (GSHP) systems. With the use of energy piles, the heat energy is fed into and withdrawn from the ground for cooling in the summer and heating in the winter, respectively.Energy piles present an innovative way to harvest near-surface geothermal energy and to provide lower carbon emissions, however, there are still pending question on their performance. During heating-cooling cycles, energy piles experience temperature changes, which result in expansion or contraction of the piles."

Jan 1, 2017

"Full time inspection of drilled shafts by qualified personnel is a necessary part of construction. Detailed inspection procedures for routine inspection are provided in the Drilled Shaft Inspector’s Manual, published jointly by the DFI and ADSC: the International Association of Drilled Shaft Contractors.The use of NDT methods or other observation methods, such as probes, video camera inspection, remote shaft wall inspection devices or various calipers are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT and other "remote" or indirect observation methods are valuable alternatives to direct entry of personnel into drilled shaft excavations. They should be considered whenever appropriate to reduce the risks of direct entry of personnel into drilled shaft excavations.As described in the Drilled Shaft Inspector’s Manual, observations made during construction are essential for quality construction of drilled shafts. The shaft depth, diameter, plumbness, bottom conditions, reinforcement, concrete continuity, and bearing conditions are most easily checked during construction. Some of these observation methods include excavation around the shaft for relatively shallow inspection, down-hole inspection for end bearing conditions or rock sockets, and video camera devices for remote inspection. In rare circumstances, a drilled shaft can be extracted for inspection. Before concrete placement, the bottom of the shaft can also be probed by drilling or coring to determine if there are voids or soft zones in the material at the base of the shaft.The Drilled Shaft Inspector’s Manual focuses on traditional "topside" inspection for routine drilled shaft construction."

Jan 1, 2004

By Mikael Calando, Thomas Joussellin

"San Francisco's rapid growth has caused the city to plan for the Transbay Transit Center Project, a visionary transportation and housing project, that will transform downtown San Francisco and the San Francisco Bay Area’s regional transportation system by creating a “Grand Central Station of the West” in the heart of a new transit-friendly neighborhood that will be home to more than 20 new towers rising a high a 1,070 ft. This paper describes the specificities of using advanced diaphragm wall technology, tooling, equipment and installation practices for deep foundation and permanent underground structures. In particular, this paper will emphasize on the urban constraints, geotechnical conditions, and the novel approaches adopted for the construction challenges of the Transbay Transit Center’s Load Bearing Elements, or Barrette PilesPaperThe Transbay Transit Center Project consists of the construction of a new multimodal, five-story Transit Center located in the South of Market neighborhood near the Financial District in San Francisco. The future Transit Center will incorporate nearly 83,000 square feet of retail, a 5.4-acre rooftop park, an extensive public arts program and bus ramps that will connect the Transit Center to a new off-site bus storage facility and the San Francisco–Oakland Bay Bridge. The new facility will accommodate more than 100,000 passengers each weekday and up to 45 million per year. Additionally, the new Transbay Transit Center will replace the since-demolished San Francisco Transbay Terminal, and nearly 20 towers, such as Salesforce Tower, will take advantage of the height increases allowed through the Transit Center District Plan.The approximately $4.5 billion project features a new five-story structure (including two underground stories) and new bus ramps which include a cable-stay bridge. The deep foundations for the pylon of the bridge (Pylon 9) consist of two each 21 ft x 5 ft barrettes (also called Load Bearing Elements in the US) extending more than 180 feet below grade and 10 feet into the bedrock. The barrettes were chosen because of the combination of high loads, significant depth and small footprint. The barrettes are installed using the Diaphragm Wall technology. Nicholson Construction was contracted by Shimmick Construction to install the cable-stay bridge’s foundation elements."

Jan 1, 2016

By Liiban A. Affi

The most difficult task of designing multilevel tieback walls for deep excavation support is the determination of lateral stresses. These lateral stresses act not only on the shored height, but also on the embedded portion of the soldier pile, all the way down to the pile tip. Examples of lateral stresses include uniform surcharge load (soil spoils or equipment), strip load surcharge from Cooper E80 (train loads), line load surcharge (exterior footing or retaining walls), and point loads (cell tower). In this paper we will discuss the various surcharges, do step by step example calculations and show how to take the total lateral stress output and present the design pressures for direct use by the substructural designer. Included is a case study from a project Anaheim Hills, California, USA.

Jan 1, 2010

By Emre Turk, Suat Gullu, Candan Gokceoglu, Ahmet Sirri, Asli Can

In this study, the ground improvement application applied under the live railway bridge's approach embankments in Sivas, Türkiye was investigated as a case study. The soil profile is mainly composed of orangish conglomerate, clay, silty sandy clay, and under claystone, and mudstone units in the study area. As a soil improvement method, the Deep Soil Mixing (DSM) technique based on the principle of simultaneous mixing the ground while injecting with the water-cement mix, was selected. The application of DSM columns is designed to be 45 degrees horizontal, in order to reach the deepest point of the soft clay units for better improvement against settlement. The core samples were taken from the DSM columns and the compressive strength tests were performed in the laboratory. The results were higher than the minimum designed values. It means that inclined DSM columns were applied successfully, and the excessive settlement problem was solved.

Oct 1, 2022

By Robert C. Simpson, Ghada S. Ellithy

"There are several methods for estimating the axial capacity of drilled shafts installed in coarse-grained soils. Most methods estimate the ultimate capacity for side friction and tip resistance. Design capacity is then calculated by applying a resistance factor to the ultimate capacity. In reality, however, ultimate resistance may not be mobilized except after a significant displacement that is not structurally tolerated in either compression or tension modes.A full- scale load test is the best way to obtain the load settlement curve for a drilled shaft, especially in soil formations where accurate estimation of soil frictional properties from a field investigation may be difficult. This paper presents the results of a static, axial, compressive bi-directional load test, using the Osterberg method (O-cell test). The test was designed so that the shaft above the O-cell would move up and the shaft below it would move down when loaded. At the start of the test the concrete around the O-cell is fractured generally on a plane near the bottom of the cell.The test was designed to validate the design capacity of drilled shafts embedded into the Vashon recessional outwash (Qvro), which is a glacially derived sediment consisting of thick deposits of cobbly sand and gravel relatively free of silt and clay found in the Seattle, WA area. The test shaft consisted of a 2.5- feet (0.75 m) diameter drilled shaft. The test shaft was installed to a depth of about 47 feet (14.3 m) into this formation. A maximum load of 437 kips (1.95 MN) was applied during the test, in each direction. The maximum load was attained at upward and downward displacements of less than 0.1 inch (2.5 mm), respectively.Although the load test did not yield ultimate values, the results are compared to the design assumptions using methods adopted in the FHWA and AASHTO guidelines, which verified the adequacy of the design assumptions. We conclude that more emphasis is needed in the prediction of the service loads and corresponding mobilized displacement that may lead to a more cost effective design. It is also clear that more testing to higher loads could lead to more efficient designs on specific projects and generally as data is added to the local knowledge base."

Jan 1, 2015

By Federico Pagliacci

Continuous Flight Auger (CFA) technique represents an important technological advance in the construction of piles in soft soils. The possibility of excavation under the water table with no need for drilling fluids, along with high productivity, have resulted in this technique?s becoming widespread in many countries. However, CFA technology has limitations because of its difficulty in penetrating hard layers and cross strata with cobbles and boulders. In these situations, pile verticality may be an additional problem. The Cased Augered Pile (CAP) technique consists of penetrating the soil with an auger housed in a casing. Two independent rotary heads sliding along the rig mast operate the auger and the casing. By adjusting the height of the casing shoe and auger bit according to soil type, it is possible to drill piles in very severe conditions - in the presence of cobbles and boulders - and to socket the pile into the rock. The use of a steel casing enables improved pile verticality. Therefore, the CAP technique is also used to construct secant piles to be used as diaphragm walls. The limitations of this technology are the depth, usually no more than 27 m (88 feet), and the size of the rig that supports the drilling tool, no less than 70 t (77 short tons) in working conditions. This paper illustrates CAP technology, the drilling system, and the characteristics of concrete and steel reinforcement and offers a case study of the Palermo-Carini second railway line, which used CAP to construct the new 30 km (18.6 mi) railway line, 20 km (12.4 mi) of which passes through the very congested downtown area of Palermo. More than 300,000 m (186.4 mi) of piles have been drilled in dense calcarenite formations with unconfined compressive strength of 15-25 MPa (2,200-3,600 lb/inch2), soft clay, and silt formations.

By Federico Pagliacci

Continuous Flight Auger (CFA) technique represents an important technological advance in the construction of piles in soft soils. The possibility of excavation under the water table with no need for drilling fluids, along with high productivity, have resulted in this technique’s becoming widespread in many countries. However, CFA technology has limitations because of its difficulty in penetrating hard layers and cross strata with cobbles and boulders. In these situations, pile verticality may be an additional problem. The Cased Augered Pile (CAP) technique consists of penetrating the soil with an auger housed in a casing. Two independent rotary heads sliding along the rig mast operate the auger and the casing. By adjusting the height of the casing shoe and auger bit according to soil type, it is possible to drill piles in very severe conditions - in the presence of cobbles and boulders - and to socket the pile into the rock. The use of a steel casing enables improved pile verticality. Therefore, the CAP technique is also used to construct secant piles to be used as diaphragm walls. The limitations of this technology are the depth, usually no more than 27 m (88 feet), and the size of the rig that supports the drilling tool, no less than 70 t (77 short tons) in working conditions. This paper illustrates CAP technology, the drilling system, and the characteristics of concrete and steel reinforcement and offers a case study of the Palermo-Carini second railway line, which used CAP to construct the new 30 km (18.6 mi) railway line, 20 km (12.4 mi) of which passes through the very congested downtown area of Palermo. More than 300,000 m (186.4 mi) of piles have been drilled in dense calcarenite formations with unconfined compressive strength of 15-25 MPa (2,200-3,600 lb/inch2), soft clay,

Jan 1, 2017

By Greg Halsted, Joshua Gilman

Today's civil and geotechnical engineers play an important role in helping to achieve sustainable infrastructure. To address environmental sustainability and climate change caused by green- house gas (GHG) emissions, all engi- neers must adjust their traditional approach to materials, design and construction practices to include a focus on minimizing carbon dioxide emissions. The considerable influence that geotechnical engineers have on projects provides an important oppor- tunity to affect positive change. The carbon footprint of the construction methods and materials used for foun- dations can be as much as 8-9% of a new building's total carbon footprint, and geotechnical engineers have an op- portunity to evaluate alternatives based not only on cost, but also the long-term environmental impacts. Growing environmental considerations and societal concerns are influencing the selection of construction materials and methods, including cement and concrete's role and significance for infrastructure applications today and in the future.

Jan 1, 2023

By Charles Winter

The Ohio Department of Transpor- tation's (ODOT's) $228 million 1-480 Valley View Bridge project was needed to keep traffic flowing on one of the state's busiest freeway segments. Deterioration from age and steady high- traffic volumes necessitated the replacement of the existing decks of the I-480 east- and west-bound bridges over the Cuyahoga River Valley in suburban Cleveland. To facilitate this work without creating tremendous backups and traffic delays due to long-term lane closures, the project included design and construction of a new four-lane bridge in the median gap between the existing 1-480 bridges. Now complete, the new center bridge allows for all four lanes of I-480 to be maintained in each direction while deck replacement and other repairs are made to the existing bridges, while also providing increased capacity after project completion. ODOT awarded the project to the Walsh Design-Build Team (DBT) in late 2017. This article describes how the Walsh DBT, with Jacobs Engineering as the DBT lead design firm, incor- porated an innovative approach to the design and construction of the driven pile foundations for the new I-480 center bridge. I-480 crosses approximately 200 ft (60.9 m) above the Cuyahoga River Valley. With an overall length of 4,150 ft (1,265 m) and spans ranging from 180 to 300 ft (54.8 to 91.4 m), the design and construction of the foundations for the new center bridge were critical to the success of the project. Due to their overall height and span lengths, the foundation loads for a typical pier consisted of a factored vertical load of 22,000 kips, (100 MN) plus significant overturning forces due to horizontal loads and thermal effects.

May 1, 2022

By Ganesh Deepak K., Anjana R. K., Dr. Kumar Pitchumani N., Rajasekharam R. M. V. M. S. S.

The Phase 2 of Chennai Metro is being introduced in the city to ease the dependence on the existing transportation systems. Phase 2 is a combination of underground and elevated metro stretches comprising of three corridors. The current study focusses on the underground stretch of Corridor 3 which has a total of 29 underground stations. Construction of the underground cut and cover stations results in ground movements, which in turn impact the structures adjacent to the excavations. The greenfield ground settlement can be evaluated with the help of empirical approach or an approach requiring finite element modelling (FEM). The paper compares empirical and FEM approaches with regards to ground conditions in Chennai. Further, with the predicted ground settlements, building damage assessment is performed. The damage category of a building is defined based on the estimated tensile strains. This paper also compares the building damage assessment with empirical method and finite element modelling.

Nov 1, 2022