Search Documents

By Donald Deardorff

"Helical piles often rely on the final installation torque for ultimate capacity verification. When helical piles are designed using traditional bearing capacity equations for deep foundations and field monitored for a specified final installation torque, a factor of safety equal to 2 is often allowed for the design. One of the more common methods of determining torque during helical pile installation is by correlating the differential pressure across a hydraulic gear motor to a torque. Most drive head manufacturers provide multipliers to convert differential pressure to torque for different drive head models. These multipliers are based on theoretical torque equations and vary with the planetary gear ratio, hydraulic gear motor displacement and drive head efficiency. Drive head manufacturers show a linear fit between the differential pressure and output torque with no scaling effect. Previous drive head testing performed by the author has confirmed that the drive head differential pressure to torque relationship is generally linear however there is a scaling adjustment needed. This results in a variation of multipliers across the differential pressure range for a given drive head.Eight hydraulic drive heads from three manufacturers were field tested by Foundation Supportworks, Inc. to compare the torque versus differential pressure curves with varying installation equipment, hydraulic line sizes and hydraulic flow rates. Differential pressure was monitored using three methods including pressure gages, PT-Tracker and an Ashcroft AT-100. Flow and temperature was measured using a Webtech system analyzer. Torque was measured using a Pro-Dig in-line torque transducer, a TruTorque indicator and a Chance Mechanical Dial in-line torque indicator. The current testing indicates that a change in installation equipment and/or a change in hydraulic flow rate may affect the torque versus differential pressure curve of a given drive head. The results of this testing also show that some of the methods for determining torque during helical pile installations may be unconservative, thereby resulting in safety factors less than required."

Jan 1, 2017

By Inc. Pile Dynamics, Daniel S. Belardo, Marcus Galvan, George Piscsalko

Soil nails are often utilized as a temporary or permanent earth retention technique for slope stabilization and for excavation retention for existing or new structures. Soils nails are generally advantageous as installation is relatively rapid and they can be installed beneath existing structures and where site access for equipment is limited. Due to the typically small cross-section of these elements, the inability to inspect the holes prior to grouting/concreting, and the various installation techniques utilized, quality control for assessing the integrity along the entire length is limited. Currently, quality assurance is conducted by load testing to verify the pull out capacity after installation. The load testing is typically done on a small percentage of the total number of soil nails. This paper will provide the results of a demonstration where the new Non-Destructive Test (NDT) method Thermal Integrity Profiling (TIP) was used to access the integrity of several soil nails along their entire lengths. This TIP method has been successfully used for several years to assess the integrity in drilled shafts and ACIP piles. The TIP method assesses the integrity across the entire cross-section and can identify regions where bulges, necks, and insufficient grout/concrete are present. TIP testing can also help assure that the contractor's installation methods are adequate and consistent for the intended design. For the project presented, instrumented Thermal Wire were affixed to the centered tension bars prior to placement in the excavated shafts. Temperature measurements were recorded from the hydration energy generated after grout/concrete placement, capturing the entire heating cycle. Manufactured defects were installed on the center bar at multiple locations. The results and conclusion will be discussed as well as recommendations for future use.

Jan 1, 2017

By Gerald Verbeek, David Tara

"When selecting an impact hammer to drive a particular pile, the decision is often based on local experience. In those cases, the contractor falls back on previous experience or draws on the experience of the hammer manufacturer to select the hammer that will be able to do the job. Obviously, a more scientific approach would be to perform a pile driving simulation using one of several commercially available software packages (e.g., GRLWEAP, AllWavePDP or PDPWave).However, this type of analysis requires quite a bit more effort. First, an accurate model of the pile driving process has to be developed, which includes a model of the soil profile at the job site and input into the analysis program. Then, the model must be analyzed to assess whether the combination of hammer, pile and soil model work.Over the years, numerous individuals and organizations have tried to develop something that would fit nicely in between these approaches: something more advanced than a gut feeling yet something that could be done on the back of an envelope; in other words, a “Goldilocks” approach — not too simple, not too complex, but just right.Screening Tool CriteriaThe goals of the approach are twofold: (1) select the appropriate impact hammer to drive an open toe steel pipe or H-pile, and (2) then use the model for the subsequent high strain dynamic testing (HSDT). The Goldilocks approach centers around five different criteria.1. Maximum Driving StressTo minimize the risk of damage, the maximum driving stresses are generally limited to 80 to 90% of the yield stress (fy) of the steel section. This approach does not consider issues such as hammer alignment, initial imperfections, denting and/or elastic buckling, and pile material fatigue history. However, even when these issues are not applicable, limiting average stresses to 0.9fy or even 0.8fy does not necessarily mitigate the risk of pile damage (Mostafa, 2011)."

Jan 1, 2017

By Pratter P., Boley C.

Polymers are well established in geotechnical applications, for example in ground improvement, where the polymers act as a binder that, when cured, holds the grains together by adhesive and cohesive forces. The subject of this research work is an innovative composite of polymers and gravel, which differs from conventional grouting materials due to its adjustable material properties. With these specific properties, the semi-rigid material can be optimally adapted to the local ground conditions and the individual framework conditions of a construction project. For the characterization of the composite material, stateof- the-art methods, such as image processing by segmentation, are presented. Segmentation is suitable for quality assurance and monitoring of laboratory samples and soil samples directly from ground improvement on the construction site. The load-bearing capacity of the innovative material can even be increased to the order of magnitude of concrete. For this reason, the soil mechanical laboratory tests in this research had to be modified and even expanded by rock mechanical laboratory tests. Based on the experimental investigations, the importance of this innovative material for practical application is demonstrated by a calculation example from construction practice, which shows that even difficult ground conditions can be handled with it.

May 1, 2022

By David R. Shields, Michael T. Bracher

"The $330 million (U.S.) Dana-Farber Cancer Institute’s Yawkey Center for Cancer Care (Yawkey Center) sits in the heart of Boston’s Longwood Medical Area. The Yawkey Center is a cutting-edge cancer care facility that houses Dana-Farber’s adult clinical care and clinical research programs. Standing 14 stories above grade, it includes 7 stories of underground parking extending 75 ft (23 m) below ground. The structure is on a 198 by 186 ft (60 by 57 m) site sandwiched between Dana-Farber’s 13-story Richard A. and Susan F. Smith Research Laboratories Building, the Medical Area Total Energy Plant (MATEP), Jimmy Fund Way, and Brookline Avenue, a busy four lane artery through the heart of the Longwood Medical Area. Together with Simon Design Engineering, the project structural engineer, GEI Consultants designed an innovative foundation and excavation support system to isolate the building from ground vibrations generated by the adjacent MATEP power plant. In effect, the Yawkey Center is a 21-story free-standing structure that starts 7 stories below grade.The MATEP facility provides power for 9 million sq ft (840,000 sq m) of occupied space in the medical area. There are six 32-cylinder diesel engine generators in the facility that produce low-frequency ground vibrations in the 10 Hz range, similar to the natural frequency of typical building elements. The resonant response of the Yawkey Center building structure to these ground vibrations would affect the performance of sensitive medical research equipment and cause an unacceptable environment for clinical care.The soil profile at the site consists of stiff clay, fine sand, glacial till, and bedrock consisting of hard metamorphosed conglomerate. In-situ measurements of ground vibrations performed in boreholes showed that there was little attenuation of the vibrations with depth in the soil layers overlying the bedrock, but the vibration amplitude in the bedrock was markedly lower than in the overlying soil. Based on this data, an innovative foundation system was designed to support the building on bedrock located up to 110 ft (34 m) below ground surface, while isolating it from the surrounding soil. This was done by physically separating the below-grade parking garage floors from the perimeter foundation walls to create a free-standing structure supported on the bedrock"

Jan 1, 2012

By Michael D. Justason

This paper describes the technology behind the development of an automated energy control system for a diesel pile hammer. Some background is given on experience using an energy monitoring system on the Route 1/I-95 interchange in Alexandria, Virginia. An adjustable hammer throttle and feedback from an energy monitoring system was then used to create a fully automated hammer energy control system. The performance of this system is described in reference to a piling project in Canada where the automated energy control system was used to obtain an unprecedented level of quality control and assurance ? data and graphs from the project are presented. The hammer energy control system (ECS) was used to successfully control and maintain a prescribed impact energy for the diesel hammer. This paper presents the first ever results from a truly automated diesel pile hammer and points to a new direction in quality control and assurance in pile driving.

Jan 1, 2006

By Alessandro Bertero, Manuel Toniolo, Vincenzo Tirozzi

"The installation of foundation elements (large-diameter Bored Piles or Diaphragm Walls) for the execution of underground works to be performed through the ""Top Down"" Technique (Stations, Car Parks, Subways, Artificial Tunnels) often requires the insertion, with pinpoint accuracy, of steel or prefabricated elements within the foundation system, to provide temporary and/or permanent support to the whole structure.The future high-speed railway station of Florence Belfiore (Italy) is a perfect example; the new station will be built in the Northwest area of Florence, about two kilometers far from the existing station of Santa Maria Novella. The project envisages installation of about 500 bored piles (1200-1500-2100 mm diameter), with lengths ranging between 50 and 70 m. In the upper inner part of 250 piles, a steel pipe (weight: 15-20 tons, length: 22-25 mt.) has to be inserted with pinpoint accuracy.The “TREVI-CALATORE” system allows to install the plunge columns and adjust their position and verticality.INTRODUCTIONThe execution of underground works via the ""Top Down"" technique, train or tube underground stations, parking shafts, tunnels, often implies the need to carefully insert steel or prefabricated structures, serving as provisional/definitive pillars, into the foundation elements.The future high-speed railway station of Florence Belfiore is a perfect example; the new station will be built in the Northwest area of Florence, located about two kilometers far from the existing station of Santa Maria Novella.The new Belfiore Station is part of the new European high-speed railway network. The works related to Florence urban penetration include (figure 1):•,a 6.5 km. twin tunnel excavated via TBM/EPB, that will run beneath Florence in a north-east direction,•,passing under more than 150 buildings, many of which can be considered historic buildings, with a soil•,coverage ranging from 6 m to 20 m;•,a North portal in Rifredi area, Firenze Castello Station;•,a South portal near Campo di Marte Station (which is also the launch shaft of the TBM)•,the new Underground Station in Belfiore area."

Jan 1, 2016

By Filippo Mira-Cattò, Andrea M. R. Pettinaroli, Elena Rovetto

"The construction of Powisle station of Metro Warsaw Line 2, in Poland, required the execution of two shafts next to an urban road tunnel adjacent to the Vistula River. The shafts were linked by three conventionally mined tunnels to be excavated 10 m below the water table level, into an upper sandy and sandy silty layer and a lower stiff clayey stratum. After a failed dig attempt under the protection of jet grouting and forepoling, it was decided to deal with the tunnels excavation problem by using the ground freezing technique as a temporary, non-polluting geotechnical treatment, keeping in service the upper road tunnel. The planning of the activities and the executive phases had a significant importance for the success of the work. For work scheduling reasons the mixed system was adopted, i.e. using both the liquid nitrogen system and the brine freezing method. The freezing process management, with a real time evaluation of the soil temperature measured by thermometric strings and an accurate monitoring of the overlying road tunnel structure, allowed the tunnel excavation and lining stages to be performed under difficult conditions, without water leaking from the frozen ground shell, within the expected times and saving extra costs.INTRODUCTIONThe new Underground Line 2 in Warsaw connects the eastern and western part of the town. One of the most critical interferences was the under passing of the Vistula river and of the Wislostrada motorway tunnel, a very congested motorway along the western bank of the river, with the construction of the new station Powisle. The construction of the station required the excavation of two shafts, using the top-down system with the creation of intermediate slabs while deepening the excavation.The shafts were used for the extraction of four Tunnel Boring Machines (TBMs), two approaching from the Vistula river side (east-side) and two approaching from downtown (west-side); in order to connect the two shafts was foreseen the realization of three tunnels, two for the underground lines and the central one for the exchanging passenger platform. These tunnels were underpassing the “Wislostrada Road Tunnel” and interfered with this tunnel foundation, which consisted of diaphragm walls (DW), the “barrettes” (Figure 1).Due to the variable geological conditions at the site, the first excavation stage, with a temporary underground support constructed of horizontal jet grouting columns and forepoling, caused the North tunnel face failure, that required an immediate filling of the empty cavities with lean mix concrete under the Wislostrada tunnel slabs. Thereafter, the recovering attempt with the grout injections could not be completed because of the development of heaves induced on the tunnel structures (Bringiotti et al. 2016). In those conditions the tunnel excavation with traditional technologies appeared to be very problematic, with high risk for the structural safety of the Wislostrada tunnel. This would have meant longer duration for the works and higher costs for the General Contractor as well as for the city Council."

Jan 1, 2015

By Brandon M. Robinson, Osman F. Besler, Dominik Gaechter

With the increase in population over the last decade, and anticipated population growth over the coming years, Norway is making significant investments in the Country’s infrastructure. Part of this investment in development starts with the Intercity development project in South-East Norway, which is the largest transport project in Norway. The Intercity Development project consists of 270 km (167 mi.) of new doubletrack rail, capable of train speeds reaching 250 km/h (155 mph). The new stations are centrally located in the major cities, in South-East Norway, to provide the benefit to as many citizens as possible. The goal of the project is to reduce the increase in traffic, which is coupled with an increase in population, and reduce the travel times between the cities. The Intercity Development Project has an anticipated completion date of 2034. The Sandbukta-Moss-Såstad (SMS) project, part of the Intercity development, includes 10 km (6.2 mi) of new double-track railway and is situated on the Østfold Line, near the city of Moss, Norway shown in Fig. 1. The 10 km SMS-section covers three open stretches and two tunnels, including 630 m (2,066 ft) substructure for double-track railways on the open line at Sandbukta. The Moss tunnel is a 1720 m (5,643 ft) long tunnel from Sandbukta to Moss center, including a 420 m (1,378 ft) long concrete culvert. The new Moss station includes an 800 m (2,625 ft) long station area. The Carlberg tunnel is a 2350 m (7,710 ft) long tunnel from Kleberget to Carlberg, including a 200 m (656 ft) long concrete culvert.

Sep 8, 2021

By Patrick Granitzki, Alicia Plinio, Janitha Batagoda, Peter Howell

The City of Newark is making a comeback with new mixed-use multi-storied Residential Development projects. The majority of developers tend to use driven H-pile deep foundation systems to support their super-structures. A different approach was recommended for one particular new development near the Passaic River. The surficial geology included glacial deposits consisting of loose to dense sand overlaying relatively soft silt and clay and a lower stratum of medium-dense sand. During a preliminary site investigation for the project, bedrock was encountered at depths ranging between approximately 168 feet to 182 feet below the ground surface. Design capacity required a single pile of 200 tons. Two different pile foundation systems were evaluated in conjunction to the typical driven H-pile system in order to review potential costs and construction schedule impacts. The two alternative pile systems evaluated were tapered tube piles and drilled displacement piles. Theoretical calculations were followed by in-situ load testing. The field testing results indicated the use of drilled displacement piles as the best option for a portion of the proposed building. This paper discusses the different piles systems considered, installation and using drilled displacement piles to minimize cost and optimize construction.

Sep 8, 2021

By Rick Deschamps, Amanda Blank, Matthew W. Drewek, Michael P. Walker

The Prairie du Sac Dam, located on the Wisconsin River, northwest of Madison, Wisconsin, was constructed 1912-1914. The spillway is an Ambursen-type, consisting of a series timber pile supported pier and buttress walls and rollway slab. The timber piles supporting the spillway, numbering approximately 5,000, have deteriorated, and the spillway structure was underpinned with over 700 micropiles as part of a design-build construction project. The underpinning micropiles needed to be arranged to avoid interferences with the existing timber piles, requiring the micropiles to be installed in the open spaces between the piers and buttresses. Inevitably, the installation of the new micropiles encountered obstructions, including existing timber piles out of alignment, as well as timber piles used to support the original construction activities and sheet pile used to control water during the original construction. This paper discusses using finite element analysis to model the spillway structure to estimate the vertical and horizontal stiffness with an extensive sensitivity analysis was performed during the design phase to account for anticipated construction challenges and potential variations in the underpinning performance. The inherent rigidity of the spillway structure allowed for load distribution to the underpinning system even when new micropiles needed to be re-located and aligned to avoid interferences with existing timber piles and other abandoned foundation elements dating back to original construction.

Sep 8, 2021

By Kenneth E. Henn, David B. Paul, John D. Rice, Brian H. Greene

"Several laboratory modeling programs have been conducted to investigate the mechanisms associated with internal erosion of dam embankments and foundations. The investigation consists of developing laboratory devices to model three separate mechanisms associated with process: 1) contact erosion along bedrock joints, and 2) piping into an open bedrock defect. The contact erosion device subjects the soil above a bedrock joint to high velocity flows in the joint. The erosion into a bedrock defect device examines a number of static and transient hydraulic conditions to study the mechanisms associated with this type of erosion. Numerous tests have been conducted using both devices. The results of the modeling will be discussed along with a discussion of how this information could be used in future dam design and risk assessment studies.IntroductionA series of laboratory modeling programs were performed to assess the seepage and internal erosion behavior of several man-made and natural structures within dams and their foundations. Each model was performed on a “bench scale” and depicted an isolated location where internal erosion was likely to occur. The models were subjected to hydraulic boundary conditions to simulate the in-situ conditions so that the processes of internal erosion could be observed. Two laboratory devices were developed to model conditions depicting 1) contact erosion along a bedrock joint in contact with a dam embankment, and 2) backward erosion (piping) into an open bedrock defect (joint, solution void, etc.).Embankment dams often have rock foundations containing defects which may detrimentally impact future performance. Further, there are existing foundations which contain rock defects that may already be detrimentally impacting the dams; however, due to the inherent aspects of the mechanism, the signs of distress may not have propagated to the surface and thus not observed during inspections. A better understanding of the mechanisms which are influenced by, and impose their influence upon, rock defects will enhance the ability of dam safety professionals to analyze the risks associated with internal erosion due to rock defects, increase our ability to monitor and successfully initiate earlier detection, and also increase our ability to design remediation methods to contend with rock defect failure modes."

Jan 1, 2016

By Ryan T. Smith, Anthony Sahj, Alexander T. Darnell

Every second can count when trying to board a departing flight or catch a ride-share to your final destination. Hartsfield-Jackson Atlanta International Airport is in the midst of a project that aims to cut about 13 seconds between automated people mover trains (Plane Train) that move passengers between the terminals and concourses. The project involves extending the Plane Train tunnel west from its existing terminus under the domestic terminal. Working from inside non-public areas of the terminal, Keller North America, Inc. (Keller) incorporated systems of micropile-supported steel beams and grillage to both underpin existing columns prior to tunneling and support open-cut excavation at the tie-in of the new to the existing tunnel. Dewatering aided in mining a challenging section at the start of the drive of the mixedface, sequentially excavated tunnel and an automated instrumentation system monitored the performance of the construction and its impact to the terminal. Cut and cover egress and ventilation tunnels required braced support of excavation.

Oct 1, 2022

By Arash Khosravifar, Ali N. Ibrahim

"Large areas of Iraq are covered with collapsible soils namely gypsiferous soil which is often used as the foundation soil for structures. In particular, the Mosul Dam foundation is comprised of high contents of gypsiferous soils. Intrusion of water through the foundation soil dissolves gypsum which acts as the binding material between soil particles. This phenomenon results in the formation of collapsible soils which can cause serious damages to the dam structure. The failure of Mosul Dam, with a reservoir as large as 11 billion cubic meter of water, can be catastrophic. In the past, Mosul Dam Authorities have been remediating the soil foundation by injecting cement mortar. This method has been proved not economic; therefore, new, more efficient, methods are desperately needed.This research study focuses on finding practical methods to remediate collapsibility of gypsiferous soils by improving their geotechnical properties. This study presents remediation of collapsible gypsum-rich soil by grouting. Three types of stabilizer materials were used to make the grout; (1) sodium silicate (Na2 O3 Si) which is a well-known chemical soil stabilizer, (2) bentonite slurry, and (3) silicone oil. The purpose for using these stabilizer materials is to provide an impermeable layer (waterproofing coat) around the gypsiferous soil particles and to fill the voids that may occur in the soil as a result of gypsum dissolution when subjected to water.A series of double oedometer (collapse) tests and direct shear tests were carried out on gypsiferous soils before and after remediation by grouting. The results show that the soil compressibility decreases in the grout-treated gypsiferous soil by reducing volumetric strain. Consequently, the potential for collapsibility decreases too. It was also shown that grouting, increases the shear strength of the soil at confining stresses smaller than 250 kPa by increasing the cohesion combined with a slight reduction in the internal friction angle.INTRODUCTIONGrouting is one of the ground improvement techniques which is often used to improve the loose foundation soils. Bruce (2003) provides step-by-step procedures on using grouting techniques for sealing dams and other water reservoirs. Grouting can be classified as permeation grouting, compaction grouting or hydraulic fracturing. Permeation grouting is an effective way to send the grout into the ground without disturbing the soil structure, i.e. free flow of grout into the soil voids where grouting is accomplished by injection of a fluid-like material that is capable of forming a gel and binding the soil particles together. Grout materials may be solution grouts or suspension grouts. The permeation grouting technique is generally used to minimize ground permeability and to control ground water flow, but it can also be used to strengthen and harden the ground (Raman et al., 2012)."

Jan 1, 2017

By Rob Jameson

Micropiles are ideally suited to seismic retrofit applications. Their high tensile and compressive capacity can sustain the large concentrated loads induced during seismic events. Micropiles can be drilled through and grouted into the wide variety of soil and rock materials encountered in seismically active zones, using equipment that operates effectively within existing structures. Micropiles have seen increased acceptance and are now widely specified for retrofit work in the San Francisco Bay Area. While installation equipment and the structural configuration of micropiles have been largely unchanged since the early 1990?s, market forces have pressured both engineers and contractors to continually optimize the cost and performance of seismic upgrades. Instead of the contractor simply developing stronger, stiffer and cheaper micropiles as isolated structural elements in response to a specification, focus has shifted to maximizing the efficiency of micropiles within the overall foundation system. The case history of seismic retrofit project in Berkeley, CA is presented to illustrate the collaboration between designers and drilling specialist which resulted in a structurally efficient and cost effective design. The seismic retrofit program for this 6-story concrete building was developed through careful consideration of the geotechnical and structural mechanisms of resistance, in combination with the deformation response of high capacity micropiles (2670 kN) under ultimate loading conditions. This case history describes the interactive project development emphasizing performance-based design and field testing to optimize the micropile foundations and the overall structural system.

Jan 1, 2008

By Michael J. Garlich

Steel sheet piling has a long history of use in a variety of permanent and temporary structures. Current engineering practice uses numerous publications and standards for design guidance. U.S. design guidance is fragmented, with numerous inconsistencies between design guides. To improve current U.S. design practice, the North American Steel Sheet Piling Association has initiated a project to produce a design standard that will unify design procedures and provide specification guidance for engineers and users of steel sheet piling. The wide range of uses for sheet pile structures presents a challenge in developing such a standard. Load factors or allowable stresses acceptable for a temporary retaining wall in soil may reasonably vary from those for a river cofferdam or a dockwall located in sea water. However, it is still possible to provide consistent and rational guidance for such varying uses. The standard also can address sheet pile design aspects often neglected in U.S. publications, such as vertical load capacity and resistance to loads applied parallel to the sheeting.

Jan 1, 2008

By David Guy, John Stanbury, Gilbert Tallard

"In 2009, storm surge from Hurricane Sandy inundated the Bay Park Sewage Treatment Plant located at El. +4 to +12 (+1.2 to +3.6 m) in East Rockaway, Long Island, NY. With all systems down, raw sewage water mixed in the floodwaters. A recurrence of such an event being unacceptable, and in view of rising future sea levels, a flood protection project was developed by Nassau County with funding coming in large part from the federally funded Sandy Rescue Fund. Designed by Arcadis/Hazen & Sawyer Engineers J.V., the protection took the form of a perimeter barrier capable of withstanding future storm surge. Due to limitations imposed by property lines and existing facilities, a levee design with three different types of cross section was developed to adapt to each location, adding construction complexity. The Long Island subsurface is characterized by beach sand extending to great depth. The clay required for the core and levee cover therefore had to be brought in from out of state. A thin silty clay layer at El. -23 to -25 (-7.0 to -7.6 m) served as an aquitard. The under-seepage was reduced by a hanging cut-off wall designed as a vibrated beam thin wall and filled with a salt water resistant, low permeability, self-hardening slurry.INTRODUCTIONOn October 29, 2009, Hurricane Sandy hit New York City, with a devastating effect on the region. The low lying Bay Park Sewage Treatment Plant (STP) (Fig. 1) serving Nassau County on Long Island was submerged (Fig. 2). All basements and underground mechanical facilities were flooded (Fig. 3) and millions gallons of effluent were released into the waters of the nearby Hewlett Bay which connects via other small waterways to the Atlantic Ocean."

Jan 1, 2016

By Mike Muchard

A design phase load test program was performed at the Broadway Viaduct bridge site to evaluate load carrying capacity and constructability of post grouted drilled shafts. The program included construction, instrumentation, post grouting and load testing of three drilled shafts. Two shafts included sleeve port and plate base grouting apparatus and were post grouted. The third shaft was un-grouted and served as a control shaft for comparison of the un-grouted end bearing. The shafts were 5 feet in diameter with the control shaft at 55 feet in length and post grouted shafts at 55 and 66 feet. SPT borings at the centerline of each test shaft defined geotechnical conditions at each shaft. Test shafts were instrumented with strain gages and concrete integrity was evaluated with crosshole sonic logging. Instrumentation and data acquisition was used during the post grouting operation to fully capture the shaft behavior. Finally, Statnamic load testing was performed on all three shafts to their ultimate capacity. The fine to coarse sandy soils in which the shafts were tipped in were well suited to improvement from post grouting. Grout pressures of 660 psi were achieved with 0.08 inch or less of upward shaft movement. Subsequent Statnamic load tests showed 183 to 192 percent greater end bearing in the post grouted shafts as compared to the un-grouted shaft. The overall result showed a potential savings of approximately 9 feet to 35 feet of drilled shaft length in addition to the increased quality assurance from post grouting.

Jan 1, 2009

By Brad W. Taylor

"During the past several months, I have introduced to civil and structural engineers an innovative solution for the integrity testing of concrete using the Thermal Integrity Profiler (TIP) Wire Cable System by Pile Dynamics. While in the process of “educating” highly-trained professionals about a technological breakthrough, I ended up being educated myself about their needs for quality control/quality assurance (QA/QC). With that in mind, I would like to focus on their two key areas of concern:• How complex is the TIP installation process?• How does the QA/QC engineereffectively analyze and report TIP test results?A few months ago, during a discussion with a senior QA engineer, he asked a question that stopped me in my tracks: “Why should we do foundation testing at all?” Turning it around, I asked, “Why wouldn’t QA/QC personnel want to know everything they could about their critical infrastructure foundation?” Honestly, I didn’t answer his question nor did I fully comprehend what he was trying to say. With his experience, the engineer understood that there has not been an integrity test or a combination of integrity tests that could deliver an inside the cage and outside the cage (cover) complete data set that would provide a definitive profile of the entire shaft. Crosshole sonic logging (CSL) becomes more effective the larger the diameter of the shaft becomes, with a maximum effectiveness between 70% and 80%, but does not provide any data of the integrity of the shaft beyond a straight line between CSL tubes. Gamma-gamma logging (GGL) provides qualitative information about the concrete surrounding the GGL tube and device, and it provides information about a small percentage of the drilled shaft concrete near its outside edge."

Jan 1, 2017

By Wei Tu

A grade separation was required to allow uninterrupted traffic crossing for a busy rail spur and a county road. The grade separation was achieved by creating a 30-foot (9-meter) high embankment that incorporates two multiplate tunnels and allows the passage of a rail spur and an existing county road. The site is located in an abandoned meander channel in the floodplain of the Mississippi River, near Osceola, Arkansas, and is underlain by more than 40 feet (12 meters) of soft clay and interlayered clays, sands and silts. Without soil improvement, the post-construction settlement would exceed 3 feet, slowly crushing the proposed tunnel structure and cutting off the railroad. Preloading, combined with vertical drains, was used to accelerate the consolidation of the underlying soil layers and to reduce the post-construction settlement under working loads. Six settlement plates were installed to monitor the progress of consolidation under surcharge load. The Asaoka observational method and the hyperbolic fitting method were used to analyze the measured settlement data to predict the end of primary settlement. The in-situ consolidation coefficient, ch, was back calculated from the measured settlement data. The stress release caused by the removal of the preloading surcharge load and the tunnel installation was determined using a Plaxis 3-D finite element model. The measured and predicted settlement using Hansbo's analytical solution demonstrated reasonable agreement. Early removal of the surcharge and construction of the tunnel prior to reaching the end of primary settlement was accomplished by analyzing the post-excavation stress reduction achieved via tunnel construction.

Jan 1, 2009