Search Documents

By Grischa Dette, Thomas Schröder, Holger Merski

For the construction of the tunnel for the new Berlin S21 light rail line, a construction pit had to be built below the crossing B 96 federal road. For this purpose, the construction pit M’ has been built beforehand as a preliminary structure for the later S21 Berlin. A crucial element of this structure is a 2.50 m deep reinforced concrete deck slab which carries the B 96. During the later construction of the S21, it became clear that the existing preliminary structure could not be used without major modifications. Consequently, the construction pit design was gradually upgraded – still with the aim of retaining the basic concept of a trough structure with a jet-grouting cut-off. As construction progressed, for reasons of stability it became necessary to develop a fundamentally new concept with an underwater concrete base replacing the jet-grouting cutoff. This paper describes the planning and construction of a cut-and-cover structure with an underwater concrete base – a layout that brings with it the difficult task of underwater excavation and concrete placing without direct accessibility from above. Special emphasis is placed on describing the innovative approaches in connection with a remotely controlled underwater dredger from the Norwegian offshore industry for excavation works. Furthermore, the sophisticated underwater technologies for concrete placing in the confined surroundings are described.

May 1, 2022

By Tsunenobu Nozaki

"Basically, the “Press-in Piling Method” was invented to eliminate construction nuisances, such as noise and vibration which have been serious unsolved problems for advancing societies over a long time. In the construction industry, piling works have been a major cause of noise and vibration, because most piling methods utilize dynamic load to install piles into the ground. The secret of the Press-in Piling Method is to utilize static loading to install pre-formed piles rather than dynamic load. The piles are hydraulically gripped and jacked into the ground by the special piling rig known as the “Silent Piler”. Therefore, the piles can form a robust and firm foundation, which is another advantage of the Press-in Piling Method.The Press-in Piling Mechanism and Implant Foundations The basis of the Press-in Piling Method is simple. The Pres-in Piling Machine installs a preformed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles, which are called “Reaction Piles”. Due to this, the Press-in Piling Machine can produce a powerful piling force whilst only requiring minimal machine size.With the Press-in Piling Method, as piles are pressed into the ground, they are incorporated with the surrounding soils, which provides a large bearing capacity and passive horizontal resistance. These embedded foundations which are firmly anchored into the ground are known as “Implant Foundations”. Being embedded into the ground, the foundations are resilient and maintain their serviceability even in the worst credible design conditions."

Jan 1, 2015

By Alison Savage, Michael Terry

"For decades, the International Market Place (IMP) has been an icon in the heart of Waikiki in Honolulu, Hawaii. It was famous for Duke Kahanamoku’s restaurant where people flocked to hear Don Ho sing in the ’60s and ’70s. Later, it was a bustling, open-air hub of small vendors who peddled everything from Hawaiian souvenirs and jewelry to food court meals and farmer’s market produce. Small buildings and shacks that housed the businesses were located on a curved tract of land — just one block off the beach — that stretches from Kalakaua Avenue to Kuhio Avenue. The entrance to the complex is dominated by a huge, old (circa 1850) Banyan tree. This tract is owned by the Queen Emma Land Company. Queen Emma was a Hawaiian Queen from the 1800s. Revenue from the land has supported the Queen’s Medical Center in Honolulu for decades.The reimagined IMP is owned by Taubman Centers, of Bloomfield Hills, Mich., and CoastWood Capital Group of San Francisco, Calif. The IMP will offer a distinctive collection of upscale fashion and lifestyle retailers, including Hawaii’s only Saks Fifth Avenue store, as well as ten sit-down restaurants, including concepts by award-winning chefs Michael Mina and Roy Yamaguchi. The mall features two large open-air courts, the first of which has the huge Banyan tree as its entryway centerpiece. The second open-air court, called Queen’s Court, includes a stage and mature monkeypod trees and a few palm trees. Foundation SelectionAfter a geotechnical exploration that was directed by SME, Plymouth, Mich., and performed by Geolabs, Honolulu, it was discovered that the historical site had hidden and challenging foundation conditions. The subsurface conditions included a very deep but now in-filled ancient river valley containing more than 180 ft (54.9 m) of lagoonal deposits consisting of normally consolidated plastic clayey silts and silty clays with blow counts mainly varying in N-value from 1 to 6. The silt was underlain by several soft coralline layers, some overconsolidated clays and various basalt layers. The static groundwater level on the site was at a depth of about 5 ft (1.5 m), closely matching sea level.Although driven piles had previously been used as the preferred deep foundation support for adjacent structures, this area of town is now fully developed and local noise ordinances preclude their use. Augercast piles were initially considered, but when the general contractor dck/FWF, Pittsburgh, Pa., asked for bids for the augercast piles, several foundation contractors offered alternate systems. The practical installation depth of augercast piles was limited and due to the depth of the in-filled alluvial valley, this system could likely have left soft silt below the tips of the piles over much of the site."

Jan 1, 2016

By Glenn J. Rix, Eduardo Tavera, Raphael Siebenmann, Zhongjie Zhang, Robert C. Bachus, Jongwon Jung

"The Louisiana Department of Transportation and Development (LADOTD) uses a variation of the FHWA-modified Gates equation to verify the nominal pile bearing resistance, typically on smaller projects where static load tests and dynamic monitoring are not practical. An inconsistency in the resistance factors for load and resistance factor design (LRFD) penalizes the target pile capacity needed during field observation if the LADOTD dynamic formula equation is used, which is unreasonable, and has created confusion among designers, consultants, district personnel, and inspectors in Louisiana. The objectives of this project are to recalibrate the FHWA-modified Gates equation and update the associated LRFD resistance factor for pile types and local soil conditions encountered in Louisiana. Improved consistency relative to the current design approaches will be achieved if the updated resistance factor matches or exceeds the worst-case resistance factor used by LADOTD, which will reduce confusion among users. Updating the resistance factor will also serve to increase confidence in the FHWA modified Gates equation, optimize the efficiency of the piles, and reduce project costs.IntroductionThe original 1957 Gates pile driving formula (Gates, 1957) is an empirically derived dynamic formula that is used to predict pile capacity in the field during pile installation. The original Gates formula tends to over-predict pile capacity for low driving resistances and under-predict pile capacity for high driving resistances (Hannigan et al., 1998). Thus, the Federal Highway Administration (FHWA) proposed a modified version of the Gates formula that addressed this limitation. The FHWA–modified Gates equation is:"

Jan 1, 2017

By Racquel Nottingham, Freddy Lopez, Ole Gadermann

The ongoing urban development is a global phenomenon, placing has high demands on urban infrastructure (housing, public services, transportation, telecommunications, etc.). Micropiling is one of the most successfully implemented deep foundation technologies in urban interventions, and in densely populated and built-up areas. The use of micropiles enabled the implementation of several solutions within short time frames, with minimal disturbance to the daily activities of the population. Since urban interventions usually represent a very important investment and have an economic impact, special attention should be paid to the serviceability of the urban infrastructure in the middle and long term. For the foundations, the design loadbearing capacity of the used structural elements needs to be guaranteed during the planned life time of the structures. In the case of micropiles, it must be ensured that the steel load bearing elements are effectively protected against corrosion. This paper presents the structural design of permanent self-drilling micropiles, subject to tension due to uplift loads. For the case study, different micropile systems - available worldwide - will also be evaluated. For the afore mentioned micropile systems, the design considerations regarding the durability of the reinforcement, based on their corrosion protection approaches, will be presented in this paper.

By Safwan Labanieh

An experimental set-up is specially designed to study the behavior of a friction pile of 3 cm diameter in contact with the soft clay of Mexico City in a small calibration chamber (CC) of 30 cm diameter and 50 cm height. The consolidation of this compressible clay is accomplished using a special system adapted to the CC itself to insure a good knowledge of the initial state. Loading results of the pile under a consolidation pressure of 50 kPa indicate an elastic mobilization of shear stresses at the shaft of the pile (?3 kPa for 1mm displacement) followed by a hardening plastic type behavior. Unloading-reloading results indicate a mobilization of shear stresses of the same type and of the same order of values obtained from the virgin loading stress path. Cyclic loading (?40 cycles) between 0 and 1 kPa (1/3 of the failure value) give similar results to those obtained from virgin loading.

Jan 1, 2002

By Frederick C. Rhyner

The United States government sponsored the construction of a new vehicular bridge over the Diyala River in Bubriz, Iraq. This paper describes the geotechnical engineering for design and construction of drilled shaft foundations for this bridge. An Iraqi geotechnical engineering firm made borings and laboratory tests while analysis and design recommendations were provided in the United States. Despite the severe challenges of engineering in a war zone, excellent cooperation was the key to a successful effort. Three drilled shafts designs were necessary to accommodate the different subsurface conditions: a) medium-compact to compact sands, b) stiff to hard clays and c) mixed soil profile. The alpha and beta methods were used to estimate capacities for a conservative design, recognizing that quality control during construction might be less than what is normally provided in the United States. Iraq has a high seismic risk and LPILE was used to estimate the drilled shaft response during earthquake loading conditions. Settlement estimates were made using FHWA methods. Construction was carried out entirely by local Iraqi firms, despite the challenges of working in an active conflict area.

Jan 1, 2009

By George J. Tamaro

In 1967 the Port Authority of New York and New Jersey undertook the construction of the World Trade Center (WTC) diaphragm walls, installation of the lateral support system and the excavation of the site, commonly referred to as the "Bathtub". The work took two years to complete. In 2001 the City of New York undertook the re-excavation of the site after the terrorist attacks. The recovery work will take eight months to complete. This paper describes the initial work on the WTC "bathtub" in the late 1960s and the recent work during the recovery.

Jan 1, 2002

By Robert B. Bittner

The new gated dam on the Monongahela River at Braddock, Pennsylvania, was built for the US Army Corps of Engineers using an innovative ?In-the-Wet? technology. A key feature of this technology involves construction of the foundations through the water and later mating the completed structure or a shell of the structure to the pre-installed foundation. This paper presents a description of the structure, its foundation, construction sequence and design details required to successfully implement this technology.

Jan 1, 2013

By Donald A. Deardorff

The capacity of a helical pile can be determined analytically using the individual bearing or cylindrical shear methods which are dependent on soil strength parameters and helical bearing area. The torque correlation method is widely used in the helical industry to determine the capacity during installation by monitoring torque during the final seating of the helicals. This method has been shown to be a better predictor of strength than the individual bearing or cylindrical shear methods. To determine capacity using the torque correlation method, the final average installation torque (ft-lbs) is multiplied by an empirical torque correlation factor (Kt, ft-1). Kt values have been well documented for square bar shaft helical products and can vary from about 3 to 20 ft-1 depending on pile geometry and soil type. A default value of 10 ft-1 is generally used for all square shaft sizes and soil conditions. Less research has been done on determination of Kt for round pipe shaft helical products. Studies have indicated that factors which affect Kt include soil type/strength, number of helical plates, helix spacing, helix pitch, depth of embedment, downward pressure (crowd), shaft diameter (round pipe) and load application direction while other studies have discounted some of these factors as inconsequential. This paper reviews past research findings regarding Kt determination for square and round pipe shaft helical products and presents a case history of round shaft helical pile installations in Chicago clay which resulted in much lower than expected Kt values.

Jan 1, 2007

By Julie Hampden, Tim Dardis, Per Reinhall

"Noise from impact pile driving can harm fish, marine mammals and other sensitive wildlife over large areas. Marine pile driving is highly regulated, and regulators require sound levels to be below certain thresholds to avoid harassment and injury to sensitive marine life. In many locations, timing restrictions, use of noise attenuation technologies and extensive monitoring for impacts to wildlife are also required. As a result, permitting can be laborious and time consuming, and project implementation and scheduling can be complicated. Underwater noise levels are measured with an underwater microphone (hydrophone), which converts noise pressure to voltage and is calibrated to express the noise pressure in Pascals (Pa). The pressure is often expressed using a logarithmic scale, in decibels (dB). Several specific metrics can be used to describe underwater noise. Three common metrics are the instantaneous peak sound pressure level (dBpeak), the root mean square pressure level (dBRMS) and the sound exposure level (dBSEL) referred to as the peak, RMS and SEL levels, respectively.During impact pile driving, the peak pressure represents the instantaneous maximum pressure, either overpressure or underpressure, observed during each pile strike. The RMS level is the square root of the mean of the square of the pressure during the duration of the impulse; it is the average pressure level of the pile strike from beginning to end. The cumulative SEL (SELcum) is calculated by summing the cumulative pressure squared and integrating over time of duration of the pile strike. SEL is used as an indication of the cumulative energy of a pile driving event, which may consist of one or many pile strikes.Regulatory agencies use these metrics to help characterize the noise pressure levels that can affect sensitive species. Some of the most frequently encountered biological thresholds in the Northwestern United States that are used by regulators to describe potential impacts to sensitive species are summarized in the following table. Agencies have defined thresholds for different types of injury, either hearing or bodily harm, and for temporary injury or disturbance."

Jan 1, 2017

By Andreas Massarsch

Information Technology, IT, is rapidly affecting all aspects of private life and how professional activities are conducted. Probably the most important development is the Internet, which makes it possible to exchange information independently of time and geographic location. While traditional communication is based on limited availability to information, the basis of the new Information Technology age is abundance and unlimited access. IT has evolved into a powerful resource and new applications are being developed and introduced almost daily. IT influences every aspect of our private life as well as our business environment. If properly used, IT can become an important resource for planning and implementing construction projects more efficiently, at lower cost and with higher quality. Interactive Web Platforms are already being used for group collaboration on a global scale. As these can be used without programming knowledge and are user-friendly, Web Platforms make cooperation more efficient and stimulate members to actively participate. Another application of growing interest are Internet Platforms and electronic publishing, which can provide technical and other information in different formats and much cheaper than conventional books or proceedings.

Jan 1, 2002

By Jim Henry

I would say mainly the cost. I showed only 3 cases. One of them was the one that Allen just described and there were two other cases. In those cases it was fairly easy to develop a solution using limited mobility grout to treat the soft soils suitable for the limited bearing pressures required by the structures. LMG readily provided a fairly reliable system for the foundation support at a reasonable cost.

Feb 10, 2003

By Ivan Hee

The 2.5km long bridge over the Beauharnois Canal and St. Lawrence Seaway is a major structure in the new Autoroute 30 project near Montreal. Foundations for the bridge consist of footings on bedrock, driven piles, and drilled shafts. This paper describes the design, verification, and construction of 1.85m diameter drilled shafts socketed into very strong and abrasive dolomitic sandstone. Two loading tests on sacrificial, heavily-instrumented, 1.18m diameter test shafts using Osterberg load cells were performed, with telltales installed to monitor a possible rock cone failure mechanism. The loading tests resulted in a revision to the initial design and provided a greater understanding of the cone uplift mechanism in rock. Insights gained are discussed and economies of the load testing program presented. Construction methodologies are also presented.

Jan 1, 2011

By Kyle A. Kershaw

The City of Grand Forks, North Dakota obtains drinking water from both the Red River and Red Lake River through a system of raw water intakes, shallow pipelines, and pump stations. However, during flood events, the City often loses access to the system, as evidenced during the record flood event in 1997. As a result, the City decided to construct a new gravity raw water intake system, including a pump station at the base of a 65-foot-deep, 60-foot-diameter caisson, behind a new levee system. Because of high design flood elevations and connectivity of river head to underlying soils, uplift resistance was required for the caisson. A total of 37, 2-foot-diameter, augered cast-in-place (ACIP) piles were chosen to provide uplift resistance. Because of the difficulties associated with installation of piles within the confined space of the constructed caisson and basal stability concerns, installation was completed from the existing ground surface to a depth of 120 feet. Several design and construction issues arose, including squeezing ground during pile installation, placement of long reinforcing bars, and installation of a dual material pile. A dual material pile was required to ensure that the ACIP pile below the base of the caisson was structurally sound and the pile above the base of the caisson could be easily excavated during sinking of the caisson. This paper discusses the solutions to each of these issues, as well as construction sequencing, load testing and integrity testing of the ACIP piles, and the successful completion of the project.

Jan 1, 2003

By Edward C. Clukey

A deep mixing method (DMM) foundation was selected by the Project Team for a very largeLNG facility in West Africa. As described in a companion paper, this foundation consists of alarge number of columns installed by mixing cement with in-situ soils. The foundations arearrayed as a variety of honeycombed type configurations which, if installed to desiredspecifications, can provide a robust foundation alternative. The foundation is capable ofdistributing loads and limiting settlements even if some of the soil in the columns is not fullymixed during installation. An important part of the overall quality assessment program,therefore, involved developing a testing program to verify the methodology. In addition theimpact of potential defects in columns on the overall foundation integrity had to be assessed.This paper describes some of the preliminary work done to establish the requirements for thequality assurance program. A key component of this program involved the samplingfrequency used to assess potential defects in the columns. To verify the column integrity 104-mm samples were taken continuously at a selected frequency through the 23 m longcolumns. The preliminary work described in this paper demonstrated that the appropriatesampling frequency depends on both the desired reliability level as well as the number ofdefective columns encountered during testing. Initial finite element analyses were performed to assess the extent that defects could occur incolumns within the honeycombed structure without adversely affecting the overall foundationintegrity. The results from this work demonstrated that the spatial location of the defects wascritical to properly assessing the foundation integrity. In addition to column sampling a load test was performed as part of the foundationverification process. The methods used to apply appropriate loads so that loads at thebottom of the columns approached design values are discussed in the paper. The results obtained from this preliminary study were then used to help develop a morecomprehensive assessment program, described in a companion paper, to determine therobustness of the DMM foundations for both the LNG processing facilities and a condensatetank.

By James S. Graham

Marine design and construction methods are presented on the caisson foundations for the tower piers at the Brooklyn, Ben Franklin, Delaware Memorial 1st, Tappan Zee, Walt Whitman, Throgs Neck, Verrazano Narrows, Delaware Memorial 2nd, and Newport Bridges. All of the bridges are founded on caissons, bearing on bedrock, soil, or piling. Caissons at the Tappan Zee Bridge are partially supported by piling and partially by buoyant forces. General subsurface conditions for each are provided. The purpose of this paper is inform engineers how bridge foundations using caissons were built over major waterways in the Northeastern USA in the past, anticipating a surge of new bridge construction in the near future.

Jan 1, 2005

By John P. Briand III, Douglas J. Aghjayan, Robert E. Fosse

This paper highlights the successful pile load testing program for the redevelopment of Pier One in East Boston, Massachusetts. Pier One is a 5.4-acre parcel on a dormant waterfront site used in the 1950s as a warehouse and distribution facility. The developer plans to re-use the existing 14-inch-diameter concrete-filled steel pipe piles to support four 5- to 7-story apartment buildings above a 2-story parking garage. A pile load testing program was developed to establish if the existing piles could support design loads of 240 kips for project financial feasibility and up to 300 kips for a significant reduction in future foundation costs. The Phase 1 program consisted of statnamic and dynamic load testing on two piles with two loading intervals (200 and 240 kips). Based upon the favorable results of the Phase 1 program, the Phase 2 program involved statnamic load testing on two piles and dynamic load testing on ten piles with three loading intervals (200, 240, and 300 kips). The Phase 2 program confirmed the favorable results which were applied across varying strata thicknesses and pile embedment depths. The average allowable capacity for the piles tested was greater than 300 kips with pile movement up to 0.3 inches.

By Peter Cali

There is one organization in Sweden, The Swedish Deep Stabilization Research Centre, which has been working with these questions and there is also a project, Eurosoilstab, within European Union to take a manual for deep stabilization.

Feb 10, 2003

By A. C. Galvis-Castro, R. Salgado, M. Prezzi, E. Ganju, R. D. Tovar-Valencia

It is generally accepted that the unit shaft resistance of piles in sands is lower for tensile loading than for compressive loading. So far, very little attention has been paid to the influence of the installation method on the tensile-to-compressive unit shaft resistance ratio. The objective of this paper is to analyze the effect of installation method on the ratio of unit shaft resistance in tension to that in compression for a model pile installed in a dense silica sand. To study installation effects, load tests on model piles were carried out in a half-cylindrical calibration chamber with digital image correlation (DIC) capability. The model piles were either jacked in one stroke using a constant rate of advance, or pre-installed into the dense sand samples. Digital images of the model pile and sand were taken during the load test and processed using DIC to obtain the displacement field in the sand. It was found that unit shaft resistance was essentially the same in tension and compression for the pre-installed pile, however for the jacked pile, the unit shaft resistance in tension was approximately half of that in compression. DIC analysis revealed that: (1) during the load test, more displacement occurs in the soil domain for the pre-installed pile compared to the jacked pile, (2) for the jacked pile, the magnitude of displacement in the soil domain is greater in tension than in compression and (3) for the pre-installed pile, the magnitudes of displacement in tension and compression are similar. INTRODUCTION Pile foundations can be categorized into two main types depending on the method of installation: displacement piles (e.g., jacked or driven piles) and non-displacement piles (e.g., bored piles or drilled shafts) (Basu et al. 2010; Salgado 2008). The response of these piles to loading can be studied in the laboratory by means of calibration chamber experiments on model piles that are either jacked into the samples, representing displacement piles (Jardine et al. 2005; Lee et al. 2011; Tovar-Valencia et al. 2018), or pre-installed in the sand sample, representing non-displacement piles(Galvis-Castro et al. 2019a; Le Kouby et al. 2013; Tehrani et al. 2016)

Jan 1, 2019