Search Documents

By N. Som

The pile capacity in cohesive and granular soils depends on a number of parameters. The values of these parameters as recommended by Indian Standard Code of Practice vary over wide ranges. A designer often finds it difficult to select appropriate values of these parameters for realistic estimate of a pile capacity. The present paper makes a critical review of the values of the parameters given in Indian Standard Code of Practice and suggests a realistic approach to selecting them in the light of recent research.

Jan 1, 1996

By Ian Vaz, Takefumi Takuma

"The New Orleans area has been repeatedly flooded by major storms and hurricanes since its French colonial era. After severe flooding in May 1995, the U.S. Congress authorized a massive flood protection project called the Southeast Louisiana Urban Flood Control Program (SELA) in 1996 to improve interior drainage in Orleans, Jefferson, and St. Tammany parishes. However, the project was not fully funded before the landing of Hurricane Katrina in 2005 and Hurricane Rita, which breached many of the area’s levees and flooded 80 percent of the city. Finally, the project was fully funded in 2008 and has been worked on towards its 2017 completion. Another large project simultaneously worked on in the area is the Hurricane and Storm Damage Risk Reduction System (HSDRRS). This system was designed for a 100-year level of flood risk reduction. One particular project within the HSDRRS rendered successful due to an unconventional method of pile driving that was utilized to install sheet piles to reinforce an existing concrete I-wall. This paper will discuss how and why this non-vibratory method of sheet pile installation allowed the project to be successfully completed ahead of schedule.INTRODUCTIONSteel sheet piles were utilized on many of the SELA and HSDRRS projects for permanent cutoff walls under concrete I-walls or T-walls or for temporary earth retaining walls of drainage structures. Although the SELA Project was established in 1996 after severe flooding the year before, hardly any work was done on it until the two catastrophic storms Hurricanes known as Katrina and Rita triggered its revival. These two hurricanes also triggered the HSDRRS soon after the storms’ devastation. The SELA project authorized to improve interior drainage systems while the HSDRRS project was authorized to raise or restore levees and floodwalls mainly along Lake Pontchartrain, the Mississippi River, and Lake Borgne in addition to other areas. Figure 1 shows the SELA Projects that have been completed, are still under construction, or approved for construction. The projects fully highlighted in yellow within the map specified the press-in piling method. These improvements included drainage systems, pump stations, surge walls, and outfall canals as enhanced protection for future storms similar to Hurricane Katrina that caused so much damage by inundating the New Orleans area in August and September 2005 respectively (Facts and Figures, 2012). The completion of these projects were the responsibility of the U.S. Army Corps of Engineers, New Orleans District.Due to the fact that many of the projects were in densely populated areas, the Army Corps of Engineers specified a non-impact, non-vibratory press-in piling method for driving and extracting sheet piles for many of the projects to mitigate noise and vibration impacts. The soft soil conditions in the New Orleans area was also a contributing factor in the Army Corps of Engineers’ decision to specify this piling method due to the risk of settlement for existing historical as well as modern structures. In addition, there were other projects that elected to use the press-in method without any contractual requirements. One of these projects was the Inner Harbor Navigational Canal Reach II Emergency Interim Repair which was part of the HSDRRS project that has been under construction since its authorization in 2005 (Facts and Figures, 2012)."

Jan 1, 2017

By Sunil S. Basarkar, Dilip M. Dewaikar, Rajesh H. Gajjar

"A load transfer program AXPILE was developed for simulation of the loadmovement characteristics of socketed piles of the Mumbai reg ion. This program used empirical relationships for ultimate shaft resistance at pile-rock interface recommended by Zhang and Einstein (1998). According to their recommendation, ultimate shaft resistance at pile-rock interface is related to the square-root of uniaxial compressive strength of intact socket material by a parameter C, which ranges from 0.4 for smooth sockets to 0.8 for rough sockets. Results of three instrumented pile load tests were compared with the AXPILE generated results. The comparison of analytical and field estimates of the unit shaft resistance confirm the recommendations of Zhang and Einstein (1998) on the unit side shear parameter c,, which was found to be in the range of 0.35 to 0.67.INTRODUCTIONInstrumented pile load tests were carried out on the test piles at the Bandra-Worli sea link project in Mumbai city of western India. High capacity socketed piles were required to take up loads from the superstructure. Hence, in addition to the available toe resistance, an accurate measurement of the shaft resistance in socket portion was desired. The instrumented load tests incorporated Osterbergcell (0-cell) assisted by strain gauge instrumentation to estimate the shaft resistance mobilization in the socket portion.AXPILE load transfer program was developed for load-movement simulation of socketed piles (Basarkar, 2004). The load transfer algorithm based on Coyle and Reese (1966) was incorporated in this program, which used empirical correlations and functions to account for load transfer in piles through shaft and toe resistance.This paper compares the computed unit shaft resistance from the AXPILE program with the measured values recorded from the instrumented pile load test."

Jan 1, 2005

By Dan A. Brown

The following paper was written by Dr. Dan A. Brown, P.E. Brown is an Associate Professor at Auburn University's Department of Civil Engineering. The paper was originally presented at a FHWA's Transportation Research Board meeting and is presented here with the author's consent. Construction and design of drilled shaft foundations in hard pinnacle limestone requires flexibility from all parties involved due to the variability of the subsurface conditions. This article describes some strategies which have been found useful in the Birmingham, Alabama area. The importance of well trained and experienced field personnel in these conditions is noted. It is also vital that engineers understand the construction challenges so as to provide both quality assurance and cost effectiveness in design and in the specifications.

Jan 1, 1991

By Walter Ensinger

Special foundation works is one of the most innovative sectors in civil engineering and construction. Both engineering techniques and construction machinery are undergoing continu­ous further development. These developments are providing ways to meeting the world-wide requirement for special geotechnical works even faster, even better and more efficiently. Unfortunately, accident prevention organisations have had to realise that the figures on in­dustrial accidents in special foundation works are still above average in number. The Safety & Environmental Working Group of the EFFC thereupon started to carry out a survey on acci­dents occurring in this sector and used this information as a basis for the preparation of acci­dent statistics and an accident analysis. The objective of this undertaking is to determine key accident occurrences and their causes and to consequently determine measures for improved health and industrial safety.

Jan 1, 2002

By B. B. Broms

Embankment piles are common in the Scandinavian countries (Kjellman, 1940) and in Southeast Asia as support of fills, light structures, bridge abutments and deep excavations (Eide, 1968) as described in the following. Untreated timber piles are often used for light structures and shallow fills when the ground water level is high since they are inexpensive and readily available. When the applied loads are relatively high precast concrete piles and steel piles are preferred. DESIGN CONSIDERATIONS Embankment piles carry the load from a fill or a struc-ture either through skin friction along the sides of the piles (Fig. 1a) or through a precast concrete slab or through pile caps at the top of the piles (Fig. 1b). When the load is carried by skin friction it is often economical to use small diameter timber piles because of the large surface area (Asplund, 1939). For precast concrete or steel piles concrete caps are used to transfer the load to the piles due to the relatively high capacity of the piles since the skin friction resistance alone is not sufficient to transfer the load to the piles.

Jan 1, 2010

By Frederick W. Slack

This paper will discuss the inherent value engineering associated with the design and construction of approximately 184,000 SF of anchored tieback wall, installed as part of the widening and drainage improvements for KY9 in Campbell County, Kentucky. The total project is 2.2 miles in length. The anchored walls, excavation grading and drainage total to a complete project cost of $28.4 million. This is one of the largest design-build projects undertaken by the Commonwealth of Kentucky. It also features another first for the Transportation Cabinet - the general contractor is responsible for quality control/quality assurance. The project is located just south of Cincinnati, OH and is situated along the east bank of the Licking River. The slopes along this stretch of the river have had a long history of movement and instability. The Kentucky Transportation Cabinet advertised the anchored wall portion of this project to be designed and constructed by pre-approved specialty contractors. The Transportation Cabinet provided the basic design parameters to each specialty contractor. Aspects to be discussed include the site and project history, previous attempts at slope stabilization along existing KY9, the technical proposal and bidding process, and the actual design and construction.

Jan 1, 2003

By Donald A. Bruce

The paper reviews aspects of the construction and performance of prestressed ground anchors installed in soils and weak rocks. Attention is focused on good practice for drilling, tendon fabrication and handling, grouting, stressing and testing. Regional variations - not always logically justified - are described. The performance of anchors in a variety of geological conditions is illustrated with reference to recent full scale test programs. 1. Introduction In the United States there has been steady growth in the use of prestressed anchors in materials other than competent or hard rock, in the years since their introduction in the late 1960's. This expansion has to a large extent been driven by specialty geotechnical contractors who both imported foreign developments and conducted their own basic researches, in locally prevailing conditions. With such data and experience, these engineers have had the confidence to promote "alternative solutions" for difficult earth support problems to receptive designers and owners. In turn, being engaged in the details of design and performance monitoring has given these parties the close exposure necessary for the real transfer and understanding of the technological concepts, and this knowledge has generated positive feedback for the contractors.

Jan 1, 1991

By Dan A. Brown

The New Mississippi River Bridge (MRB) employed conventional design-bid-build procurement, but the bidding process included the opportunity for pre-qualified bidders to develop and propose confidential Alternative Technical Concepts (ATC?s) for evaluation and approval in advance of bidding. The ATC process provides a mechanism for value-engineering prior to bid, with incentives and opportunities for both the owner and the bidding contractor. The contract described in this paper is for the river bridge composed of a cable-stayed crossing with two pylons and the anchor piers on each side of the river. The Massman-Traylor-Alberici (MTA) team developed a re-designed foundation system for the main pylon and anchor foundations which utilizes their equipment and experience along with field load test measurements to optimize the foundations. The paper describes the experience with the use of the pre-bid ATC process on the project from the perspective of the bidder, and outlines some of the benefits and limitations of this concept with respect to foundation design and construction. Some keys for success are identified and impediments to the effective implementation of the process are described.

Jan 1, 2011

By William J. Neely

Augercast piles are formed by drilling a continuous-flight auger into the ground and, on reaching the required depth, sand-cement grout or concrete is pumped down the hollow stem as the auger is withdrawn. The sides of the hole are supported at all times by the soil-filled auger, eliminating the need for temporary casing or bentonite slurry. The augercast piling method is fast and economical; there is no vibration, very little noise and, if executed properly, no ground displacements during installation. The method is well suited to sands which are easy to drill and are readily transported up the auger. Relatively little attention has been given to augercast piles in the literature which might be part of the reason for the considerable variations in local practice, building code requirements and design methods. The purpose of this paper is to discuss some of the features of augercast pile installation that are known to influence both the structural and geotechnical capacity of the pile, to evaluate several empirical design methods and to look at some important aspects of quality control of augercast pile installation.

Jan 1, 1990

By Chris Harnan

This paper describes the geology of three European cities and outlines how the geology has lead to the development of specific foundation construction techniques. Comparative tables of techniques commonly employed are given in Section 5. It can be seen that despite the presence of the 'single market', techniques still have wide diversity despite some similarities in geotechnical conditions.

Jan 1, 2000

By Timothy J. Myers

Expansion and the economic growth in the southwestern region of Missouri necessitated the expansion of State Route 249 and the construction of a new interchange to provide service to the Joplin, Missouri area. The project is located above a former lead and zinc mine in Jasper County, Missouri and includes a five bridge interchange connecting State Route 249 and US Route 171. The variable subsurface conditions, both natural and manmade, prompted the design team to use ground improvement via grouting and small diameter micropiles to provide support for several of the bridge foundations on the project. The scope of work included mine shaft closures, 56,000 ft of overburden and rock drilling, 11,139 ft of micropiles, 524 cy of balanced/stabilized high mobility grouts, and over 8,700 cy of low mobility grout. The selection of the grout used was based on the actual subsurface conditions. Low mobility grout (LMG) was used in voided conditions and for closure of the mine shafts encountered during the excavation. High mobility grout (HMG) was used in fractured rock with the goal of improving the mechanical properties of the rock underneath the future bridge footings and controlling grout volumes during micropile installation. The split spacing method was utilized for both LMG and HMG holes. Geology of the project site subsurface consisted of extremely variable bedrock with strong to very strong limestone, chert, breccia, extremely weak shale, and weak to strong sandstone. Previous activities associated with the mining disturbance (such as partial filled vertical mine shafts, shallow and deep mine horizons, modified hydrology including artesian conditions) further complicates the site subsurface conditions. Real time monitoring and recording of all drilling and grouting parameters was conducted to assist in the evaluation of in-situ geological properties of the site in order to modify the ground improvement and micropile program as necessary. This paper will discuss the design and execution of the ground improvement and micropile program. The project is an excellent example of the use of multiple ground improvement and foundation support techniques combined with real time data analysis to provide a foundation support solution for a complex geological environment.

Jan 1, 2009

By A. F. van Weele

In general cast-in place piles will have an irregular pile shape. However, it is possible that these irregularities are so large that they may lead to pile deficiencies. It is very rarely possible to examine the pile foundations visually. Also the performance of a static or dynamic load test on each individual pile is not practical and much too expensive. This is the reason why pile integrity tests have been developed: to reduce the risk of inadequate pile foundations by performing a simple test. Pile integrity tests are non destructive tests which are carried out after a pile has been installed. Over the years a number of techniques have been developed of which the most important techniques are briefly described in this paper. Of all pile integrity testing methods, Sonic Integrity Testing is the most widely used method in western Europe. This method has been developed by TNO some 15 years ago. Since then the method has been improved, largely due to advances in micro-processing. A major improvement was made by the introduction of digital signal processing techniques. This made the Sonic Integrity Testing method more accurate (smaller defects can be detected), faster (more than 200 piles can be tested on a single working-day) and more reliable (the results are easier to interprete). A few cases will be presented which will show the usefulness of the Sonic Integrity Testing method. In one of these cases, a helpful tool for interpretation of the results is explained: the Sonic Integrity Testing Simulation program TNOWAVE. Notwithstanding the fact that Sonic Integrity Testing is a powerful method, it has also some strict limitations. These will be discussed at the end of the paper.

Jan 1, 1987

By Philip Dubbeling

Conventional dynamic sheetpiling techniques are ill-suited to urban development because of the emission of excessive noise and ground vibrations. Drilled shafts and slurry walls alleviate some of these environmental concerns but add additional problems due to large bulky machines, reliance on dusty concrete plants and urban trucking grief. To solve these problems, pre-fabricated sheetpiles are hydraulically jacked-in by reaction principle using a compact and lightweight press-in machine, a so called the "Silent Piler". Through scientific analysis, definition and systemization of press-in machines and methods, new construction concepts such as the one-step approach, implant structures, functional design and life cycle design have been developed to comply with new basic construction principles.

Jan 1, 2006

By Wolfgang G. Brunner

A 3800 m long temporary water-retaining dike has been constructed under extreme conditions in the harsh northern climate to enable two of the kimberiite pipes at the Diavik Diamond Project reserve to be mined using open pits. The Diavik Diamond Project is located on East Island at Lac de Gras in Canada's Northwest Territories, approximately 200 kilometres south of the Arctic Circle. The dike which has been constructed in up to 25 m deep water from crushed granite quarried from the site projects into Lac de Gras encircles the first two of the kimberiite pipes to be mined. An 800 mm wide diaphragm cut­off wall constructed of bentonite, cement and crushed rock, totalling 33,000 m2, and a two-phase jet grouted curtain wail at its base, totalling 8,400 m2, have been installed through the dike and underlying till foundation into bedrock. The cut-off is designed to minimise water seepage from Lac de Gras through the dike. In order to ensure that the dike had adequate internal stability and diaphragm wall construction could proceed safely, the crushed rock fill material dumped into the lake was first compacted by TR 75 deep vibrators. In 2000, Bauer Maschinen GmbH of Schrobenhausen, Germany were awarded the contract for the supply of all specialist foundation equipment required on site and for providing technical support to the Canadian main contractor Lac-de-Gras-Construction throughout the construction of the cut-off walls during 2001 and 2002. Installation of the cut-off walls was completed in July 2002, three weeks ahead of schedule, and dewatering of the inner dike areas commenced just 5 days later and has continued throughout August and September. After completion of extensive testing of the diamond recovery plant, the mine is scheduled to go into full open pit production in February 2003.

Jan 1, 2003

By Tracy Brettmann

In recent years the Augered Cast-In-Place (ACIP) Pile industry has seen a substantial increase in the quality control options available to Contractors, Engineers, and Owners. Quality control methods range from the simple, manual techniques that have been used for years to new computerized installation monitoring equipment and nondestructive testing methods. Our ability to monitor and test ACIP piles has grown to such a degree that the industry is struggling to determine how much quality control is enough. This paper reviews the many options available and describes the pros and cons of each. The various nondestructive testing methods, in particular, have been difficult to apply reliably due to misapplications of methods and misinterpretation of the results. ACIP piles have unique properties that require the various nondestructive testing methods available be considered very carefully in determining the method most appropriate for a particular use. Some nondestructive testing methods, as well as automated monitoring equipment, potentially can be applied effectively to increase the level of quality control for ACIP piles. The experience gained on real projects using these new methods, in conjunction with the old procedures, provides valuable information for future applications.

Jan 1, 2000

By Mark R. Svinkin

Construction vibrations may adversely affect surrounding buildings and their effects range from human discomfort and disturbance of sensitive devices to visible structural damage. There is no unique conclusion regarding the effect of construction vibrations at every site. Measurement is usually made to monitor vibrations and control them with the vibration thresholds for disturbance of sensitive objects as well as damage to structures. To prevent potential litigation and mitigate the vibration effects on sensitive devices, people and structures, it is necessary to manage and minimize vibration problems before the beginning of construction activities or installation of vibrating machine foundations, and during construction. Pre-construction damage survey and engineering vibration investigations, including the prediction of anticipating vibrations, have to be made at most construction sites in advance of construction activities. Vibration monitoring and control have to be provided during construction. The instrumentation feedback of vibration prediction, monitoring and control provide the basis for choice of measures to prevent or mitigate vibration problems and settlement damage hazards.

Jan 1, 2002

By David E. Albus, Ahmadreza Mortezaie, Bidjan Ghahreman

The structural evaluation of seismic performance of an existing hospital in Long Beach, California, required spring constants of foundation elements. The structure included support by deep foundation elements comprised of belled (underreamed) caissons. The available relationships in the governing building code (ASCE41-13) to compute axial stiffness is not applicable due to the belled configuration of the caissons. The large diameter of the bells required consideration of the foundation medium to the axial stiffness; a detail not clearly described in ASCE 41-13. Furthermore, prescriptive equations in ASCE 41- 13 used to estimate lateral stiffness only consider pile groups with the assumption that the only source of lateral stiffness is the axial reaction of individual piles. These assumptions were invalid for the project at hand where all caissons are configured as single foundation elements, not a pile group. In the present work, the approach taken to estimate seismic stiffness of single-belled caissons is described which accounts for the elastic behavior of the foundation medium below the bell base and lateral behavior of single-pile shafts. Results of the work provide a more satisfactory derivation of the spring constants consistent with current modeling methods. INTRODUCTION Seismic evaluation of an existing hospital in Long Beach, California, required geotechnical investigation followed by site-specific ground motion analysis. This evaluation was required by the Office of Statewide Health Planning and Development (OSHPD) in order to meet the requirements of the Structural Performance Category 4D (SPC-4D) published as a part of the 2016 California Building Code, CBC (Section 3412A). SPC-4D utilizes ASCE41-13, as modified by OSHPD, and involves two seismic performance objectives: BSE-1E (20% probability of exceedance in 50 years) and BSE-2E (5% probability of exceedance in 50 years). Spring constants and capacities of foundation elements were needed for evaluation of the structural performance of the building subjected to these two performance objectives. Our review of the as-built foundation plans indicated that both shallow footings and caissons were used for support of the structure. The plans demonstrated that all caissons are belled (under-reamed) and are individual, i.e. not part of pile groups. In this paper, the subject site condition and foundation elements are described first. This is followed by details of assessing spring constants and vertical capacities for belled caissons. The new requirements of the 2016 CBC concerning the evaluation of critical facilities will likely entail evaluation of other structures with belled caissons due to the more extensive use of these foundations in the past. This paper proposes a method to address the conditions of individual belled caissons not explicitly considered in the current code provisions.

Jan 1, 2018

By Enrique Ibarra, Manuel J. Mendoza

"Abstract: This paper describes the current state-of-practice for the design of cast-in-place drilled shafts in granular soils under axial loading, addressing recent advances that take into account the surrounding soil grain size distribution and their behavior. The important role of the gravel content in the shaft response under axial loading is emphasized. Usual design approaches in Mexico are described, and the results of load tests from different sources are discussed. The analysis emphasizes the primary contribution of the lateral area of shafts to their axial bearing capacity, raising doubts regarding the common local idea of “point bearing shafts”. Finally, some lines of research are noted to permit advances in the important field of deep foundations. 1 INTRODUCTIONIn Mexico, cast-in-place drilled shaft foundations are widely used to support various structures in the west area of Mexico City, where alluvial and volcanic deposits predominate. Deep foundations are also used in modern construction works located in other major cities of Mexico. In fact, the use of drilled shafts for tall buildings and overpasses in the center of Guadalajara as well as in transportation works related to the Metro and roadways in Monterrey is well known. It is worth mentioning that these same structures have been applied in road bridges throughout the country.Procedures for pile construction in Mexico have been basically the same for the past 20 years (Paniagua et al., 2005); however, modern equipment has been incorporated into the construction industry, including innovations in sludge-drilling technology, control and the quality of the castings. In addition, novel and efficient procedures such as construction with continuous auger displacement piles have been implemented (Auger Cast in Place, ACP) and have begun to be used locally with success (Schmitter and Paulin, 2006).However, it can be argued that the technological developments that have resulted in more efficient construction procedures have not included a breakthrough in the full understanding of the phenomena or basic mechanisms of load transfer from piles to the surrounding subsoil and therefore in supported, tested and practical design methods. This is particularly true when seeking to determine the unit side shear strength of shafts drilled in granular media with gravels, where it has been observed that the commonly used calculations developed for sands underestimate the load-bearing capacity by frictionin a most important way. Due to the above reasons, it seemed appropriate to present in this paper a review of the current stateof- practice in Mexico for the design of cast-in-place drilled shafts, particularly in granular media, highlighting some recent advances and research that takes into account the grain size distribution and behavior of granular soil."

Jan 1, 2014

By C. T. Christensen

The paper gives an outline of the design, installation and performance of a series of mooring and berthing dolphins for a major ferry berth outside the port of Elsinore, Denmark. The Dolphins are large cylindrical bottle shaped and open ended steel piles vibrated into the sandy seabed. They are subsequently equipped with prefabricated fender units. Vehicle access to the ferry is via a fixed ramp and a semi-submerged linkspan. Supplementary passenger access is via a covered gangway steel bridge from an existing gangway facility to a midship door in the ferry«

Jan 1, 1989