Search Documents

By M. Hesham El Naggar, Yasser Abdelghany

"ABSTRACT: The axial and lateral monotonic and cyclic behavior of helical pile foundations was investigated and new innovative helical screw systems suitable for seismic loadings were developed and patented. More than one hundred full scale field load tests were conducted on instrumented helical screw piles installed in cohesive soil. The piles included: plain helical screw piles (P-HSP); grouted (G-HSPs); fiber reinforced polymer FRP-G-HSPs; and reinforced grouted RG-HSPs. The RG-HSP piles axial capacity was more than twice that for P-HSP, with minimal reduction after cyclic loading, and their lateral capacity was more than 3 times the P-HSPs capacity. A 3-D finite element model was established. The results of 3-D finite element modeling were used to establish the load transfer mechanism and a design methodology for the considered piles.INTRODUCTION AND LITERATURE REVIEWHelical (screw) anchors have been utilized in tension loading and have gained popularity for bearing load applications. Helical piles represent an overall cost effective alternative to conventional piles for new construction and repair applications. The helical piles speed and ease of installation, less noise during installation added advantage with regards to their efficiency and reliability for underpinning including re-support and reconstruction of distressed and damaged foundations for either stabilization or rehabilitation. The “square shaft” SS175 pile is a segmented deep foundation system with helical steel bearing plates (helices) welded to a central steel shaft. Load is transferred from the shaft to the surrounding soil through these bearing plates. Segments or sections are joined with bolted couplings. Practically installed depth is limited only by soil resistance and economics. A helical bearing plate or helix is one pitch of a screw thread. All helices regardless of their diameter have a standard 75 mm pitch (Figure.1). The performance of single helical anchors and group action were studied experimentally and theoretically by several researchers, the researches focuses on the installation torque and uplift resistance. Some researches focus on the load carrying capacity with little pile response to cyclic loading effects or to instrumented full scale field testing. Helical piles axial compressive or lateral loading still is not well characterized and needs more analyses and their seismic performance was not investigated. For such this research was initiated to investigate the helical piles monotonic and cyclic performances under axial and lateral loadings to consider their usage in different applications in seismic zones. Among the several researchers, Clemence (1983); Mooney et al. (1985) conducted field and laboratory testing; Hoyt (1989), Hoyt et al. (1995), and Ghaly and Clemence (1998) conducted theoretical and experimental testing, Puri and Vijay (1984), Huang et al. (1995), Perko (2000), and Pack (2000) conducted theoretical analyses. Rao and Prasad (1993), Prasad and Rao (1994), conducted experimental testing; Vickars and Clemence (2000) studied the performance of helical piles with grouted shafts."

Jan 1, 2014

By Flor De Cock

The paper reflects part of the work from the European Regional Technical Committee on Piles (ERTC3) during its mandate between 1994 and 1999, and, in particular, describes the find­ings from an International Seminar held in 1997 in Brussels on European practice for design­ing axially loaded piles. The seminar included contributions from 17 European countries, each of which provided a synopsis of their respective national design approaches. This paper pays particular attention to the design methods based on laboratory and in-situ test data for both bored and displacement piles.

Jan 1, 2002

By Mark M. Petersen

As part of the addition of eight new combined cycle generating units at the Florida Power & Light Sanford Plant, 2,129 piles were to be installed. The existing plant elements were supported on driven piles, and the variation in pile lengths during previous work, as well as available subsurface information, indicated a complex stratigraphy. At the request of the owner, the designer/construction manager developed a program to evaluate the use of pressure-grouted displacement piles. A pre-design load test program in areas that represented the apparent extremes in subsurface conditions indicated that the system was feasible; however, the presence of existing features that were to be demolished later precluded the clear delineation of subsurface conditions in advance of construction. A contract was negotiated with the pile installer based on the best estimate of potential pile lengths, with modifications to pile lengths to be set based on additional exploration. A total of 52 cone penetration soundings and five load tests were performed immediately prior to and during pile installation to establish correlations between the CPT data and pile performance. Pile depths were set based on these correlations. Pile installation was completed 6 weeks ahead of schedule and 15 percent under the original budget estimate. This paper documents the evaluation of pressure-grouted displacement piles as an emerging technology, and illustrates the benefits of a close working relationship between the owner, designer, and pile contractor at a site with variable subsurface conditions.

Jan 1, 2002

By Antal Partos

ATLAS Processing Company Shrevesport, LA initiated a major plant expansion in 1980. SITE Engineers, Inc. provided engineering consultation regarding the foundation of the vacuum unit. Four test borings were drilled and laboratory testing completed for shear strength and compressibility. Vertical drains were proposed to accelerate time rates of settlements. Steel erection was completed by May 22, 1981 with very small < 0.1 in., settlements. Hydrotesting was initiated on July 9, 1981 and completed on August 27, 1981. An average rebound of 0.3 in. was computed resulting into an average net settlement of 0.5 in. This paper describes in detail soil behavior during load testing.

Jan 1, 1992

By Zhang Baoshan

In this paper, the forced features and dynamic behaviors of stone-column composite foundation are concisely related. The characteristics of Rayleigh wave method is summarised. This method is proposed in which, the stress ratio of the stone-column to the surrounding soil and the bear­ing capacity of the composite foundation are determined. Through the engineering cases, it is shown that, checking and evaluating the composite foundation in this method, is feasible, with high speed and low cost.

Jan 1, 1991

By M. Pernot

A 12 m-deep excavation has to be perfomed in the Shanghai soft clay to install an underground electric substation. This article was originally intended to study the behaviour of the wall, the excavation bottom and the surrounding ground during the excavation. Since the works are behind schedule, and the data referring to the excavations are not, therefore, available, the article is limited to a presentation of the analysis methods that we envisaged for the study of the behaviour of the excavation.

Jan 1, 2010

By Bernard H. Hertlein

All methods of deep foundation construction present challenges to the contractor and engineer that vary according to the method employed, and the geotechnical conditions in which it is being used. Augered-Cast-In-Place (ACIP) piles are generally regarded as one of the most challenging, because the construction method precludes the use of traditional shaft inspection and quality control techniques. Application of Nondestructive Test (NDT) methods can provide quality control for ACIP shafts that traditional methods cannot, but each NDT method has limitations. These make some NDT methods unsuitable for use on ACIP shafts, and may limit the effectiveness of others, depending on geotechnical conditions. To help contractors and engineers working with ACIP piles select the test method most appropriate to specific site conditions, this paper presents a summary of the major NDT methods currently available, and reviews their capabilities with respect to the unique conditions presented by ACIP pile construction. Case histories illustrate how a combination of careful method selection, skilled data interpretation, and experienced engineering judgment have resolved problems and ensured quality in foundation construction by discriminating between potentially serious defects, and those that are unlikely to be significant.

Jan 1, 1997

By Peter Jackson

The dewatering of the large construction pits required for major infrastructure projects often has a significant impact on the environment. This is particularly so in urban areas and where groundwater resources are of interest. These environmental impacts are inter alia, groundwater lowering and the consequent effects such as settlement and deterioration of timber foundations, together with the impact of the dewatering on the groundwater quality. In order to minimise the environmental impact of the dewatering, the quantity of water to be abstracted and the amount of groundwater lowering in the surrounding area must be minimised. This paper describes the measures that have been taken on the Copenhagen metro project to achieve the objective of minimal environmental impact whilst still carrying out a major dewatering scheme.

Jan 1, 2000

By Thoedtida Thipparat

The diaphragm walls and barrettes are very important to the constructions of multi-storeyed buildings, elevated expressways, subway railway stations, etc. Uncertainties particularly increase in accordance with the construction progress. Overcoming uncertainties influences the construction goals including achievement of time. This paper is aimed at proposing an uncertainty assessment and delay evaluation model to assess uncertainties and evaluate delay resulting from those uncertainties. Neurofuzzy systems (NFSs) for assessing uncertainties and evaluating delays are developed. Artificial neural networks (ANNs) have ability for learning from the past data and generalizing outputs for the next applications which are provided for fuzzy logic systems (FLSs). FLSs have ability for exploiting the tolerance of imprecision and uncertainty. FLSs provide the reasoning to the ANNs. Uncertainties affecting each operation were assessed and delays were evaluated by following steps of the proposed model. The uncertainty assessment and delay evaluation approach was applied to a diaphragm wall and barrette construction to demonstrate how to implement the proposed model. The results of the test case application were used for handling delay at all operations regarding the corresponding uncertainties.

Jan 1, 2006

By S. S. Gajin

The paper deals with parametric vibrations of an axially loaded pile. The dynamic model is derived by means of Hamilton&apos;s principle and reduced to a partial differen­tial equation with variable coefficients and corresponding initial boundary conditions, taking into account the influence of the axial force. By means of Galerkin&apos;s method, the partial equation is further reduced to a Matheu-Hill&apos;s matrix partial differential equation of the second order. Since the problem of the dynamic stabili­ty has been expressed only for standing piles, the paper analyses in detail two stan­ding piles, one which is restreined, whereas the other is hinged at the toe. In both cases it is assumed that head horisontal displacement is prevented. Using Ruunge-Kutt&apos;s method, a computer analysis in the time domain is given for the characteristic parameters and possible boundary conditions. The paper analyses the stationariness of the process, as well as the dependance of the critical excitation frequency upon the pile parameters. The results have been illustrated by respective diagrams.

Jan 1, 1989

By David J. Baxter

Use of bored displacement piles has experienced significant growth in the UK piling market sector, largely due to their environmental advantages over other piling methods and through cost benefits. Bored displacement piles are a cast-in-situ construction which can be formed with minimal production of spoil and offer low noise and vibration compared to driven displacement piles. A large variety of bored displacement piles have been developed. This paper describes a standard system for their classification. The development of the different types is described along with the factors which have led to their increased use. Consideration is given to processes undergone by the soil during pile installation and design approaches for bored displacement piles are compared. Comparisons are made between the different classifications of bored displacement pile. Comments are also made on the installation of such piles. It is concluded that complex changes occur in the stress states of the surrounding soils. Such effect of the pile installation on the soil should be accounted for and there is a need, therefore, to further refine the design process for these piles.

Jan 1, 2006

By Craig T. Jones, Zachary Q. Maassen

"Jet grouting is a method of ground improvement that relies on the erosive capacity of high-speed jets to cut and mix the ground in place with a cementitious grout. A continuous return flow of cuttings, called jet grout backflow or spoils, is expelled to the surface during the grouting process. Data from projects completed in Toronto and Ottawa is presented where BOS Solutions’ services provided significant savings compared to the traditional spoils treatment utilizing vacuum trucks for spoils disposal. These traditional treatment methods are cumbersome and expensive by nature. BOS Solutions provided an alternative solution that is environmentally friendly and capable of handling full flow to process these jet grout spoils utilizing a tank system paired with centrifuges and flocculation additives to remove the ground soils and grout product from the spoils slurry. BOS’ process produced a clean water for reuse in the project while reducing the overall waste volume by producing a dry, stackable solid that could be hauled to a landfill. Benefits observed by using the BOS process were disposal waste volumes decreased over 30% and at least a 19% reduction on disposal costs.SCOPE OF WORKJet grouting is a method of ground improvement that relies on the erosive capacity of high-speed jets to cut and mix the ground in place with a cementitious grout. A continuous return flow of cuttings, called jet grout backflow or spoils, is expelled to the surface during the grouting process. The backflow, or spoils, is a mixture of grout, water and soils. Traditionally, the spoil would be collected in in-ground pits and allowed to solidify for a few days prior to hauling to a final disposal site. For the projects completed in Toronto and Ottawa, the jet grouting work was performed at street level, in high traffic congested areas, presenting the challenge of insufficient space for the contractors to process the jet grout spoils in the traditional way. At first, attempts were made of using vacuum trucks to collect and haul the wet spoils to an off-site location where the spoils would be allowed to solidify. However, this method proved cumbersome and expensive due to the high volumes of spoils generated daily and the high number of vacuum trucks required to support the jet grouting operations, respectively."

Jan 1, 2017

By Sun Shao Xian

The Port of Shekou is situated at Shenzhen Bay on the east side of the Pearl River estuary. Geological condition of the site is quite complicated. On top of the sea bed, there is a layer of soft silt 8 - 14 m thick. Under the soft silt, there are intercalated layers of sand, silt and clay. Average surface elevation of the underlying undulatory weathered bed rock is about - 20 m, with a variation of about 10 m. In certain locations, the weathered bed rock is covered with a layer of silt 3 - 4 m thick. This paper gives brief account of three types of wharf structures which are of particular interest, constructed in the last few years: (A) Platform type wharf structure with frontal sheet piling and steel raking pile in the rear; (B) Relieving Platform type structure with steel sheet piling and inclined anchoring HP pile ; (C) Steel pipe pile row supported apron added to a marginal quay. Average construction time of a deepwater berth is about six months.

Jan 1, 1991

By Fabrice Mathieu

The Cutter Soil Mixing (CSM) provides a cost effective solution for the rapid construction of retaining and cut-off walls using new equipment developed from diaphragm wall cutter technology. CSM consists of cutting and mixing drums mounted on compact hydraulic motors. Soletanche Bachy CSM has been designed to leave the space above the tool free, thereby mixing the soil efficiently during all the phases of the wall construction, with high penetration rates. The precise positioning and verticality of the wall is achieved using a kelly bar and full monitoring. Soletanche Bachy CSM is a versatile equipment which can be mounted on various carriers: pile rigs, hydraulic crane, carrier equipped with telescopic mast. The major phases of Soletanche Bachy CSM development are presented, including the results of an extensive trial carried out in Le Havre (France). The soil consists of hydraulic fill with soft soil lenses overlying sandy deposits. 20m deep panels were constructed to support a rectangular shaft. During the construction, and after its completion, the shaft was subjected to an extensive series of tests followed by a partial excavation. The paper discusses also the future development of the technique and its potential applications.

Jan 1, 2006

By M. Hesham El Naggar, Osama F. E. Drbe

"Abstract: The use of micropiles has greatly increased the last twenty years, including applications involving low capacity micropile networks, seismic retrofitting, underpinning of existing foundations and high capacity foundations for new structures. This paper presents a field study of the behaviour of single hollow core micropiles in firm to stiff lean clay. Eight micropiles were installed using hollow bars (76 mm OD and 48 mm ID) with air/water flushing technique and advanced to a depth of 5.75m: six micropiles were installed using 228 mm (9 in) drill bit and two micropiles were installed using 178 mm (7 in) drill bit. All micropiles were instrumented with linear potentiometers to measure the vertical displacement of the micropile head and vibrating wire strain gauges to measure the axial strain at three points along the micropile length. Twelve full scale tests were conducted on the eight micropiles, four monotonic compression, four cyclic compression and four tension tests. Only the results of micropiles tested under monotonic compression is presented in this paper. The full scale load tests and a comparison of the performance of the micropiles with 228 mm and 178 mm drill bit are presented and discussed in terms of load-displacement curves, bond strength and tip resistance. The results showed that the proposed values of bond strength in FHWA give a conservative design of the hollow core micropiles. The micropiles constructed with 228 mm drill bit performed marginallybetter than the micropile with 178 mm drill bit in terms of the ultimate capacity.IntroductionMicropiles have been defined in a variety of ways, but can universally be classified as small diameter (less than 300mm), bored, and grouted in place piles (FHWA, 2005; Bruce et al., 1999; and Scherer et al., 1996). They can sustain axial (compression and tension) and/or lateral loads. Dr. Fernando Lizzi used micropiles in 1952 for underpinning of historic buildings damaged during World War II (Bruce D. A., 1988). Since then, micropile applications have expanded rapidly to include underpinning for existing foundations, in situ reinforcement, and seismic retrofitting and foundations for new construction. In particular, micropiles have graduated from use in low-capacity micropile networks toapplications as single high-capacity foundation.Micropiles capacity is affected by the construction technique, which involves drilling, placing reinforcement, and placing or pressurizing the grout. For example, the drilling method influences the degree of bonding between the grout and the ground, and the placement of reinforcement and the choice of grouting method have an impact on the development of the bonding. Bruce et al. (1997) showed that grout/ground bond is most affected by the grouting method. Based on the type of pressure applied during the grouting process, micropiles are classified as follows (FHWA, 2005): Type A: grout is placed under gravity pressure only using either sand-cement mortars or neat cement grout. Type B: pressures typically in the range of 0.5 MPa to 1 MPa are applied in order to inject the neat cement grout into the drilled hole while the temporary drill casing is withdrawn. Type C: involves two-step process; neat cement grout is first placed in the hole under gravity pressure head only as in type A, and prior to the hardening of this primary grout, a similar grout is then injected via a preplaced sleeved grout pipe at a pressure of at least 1 MPa. Type D: like type C, this type is a twostep process: neat cement grout is placed in the hole under gravity pressure head only (but pressure could be applied in some cases), additional grout is injected via a sleeved grout pipe at a pressure of 2 MPa to 8 MPa once the primary grout has hardened. In some cases, a packer is used inside the sleeved pipe, enabling specific horizons to be treated. Recently, Type E micropile is proposed, which involves"

Jan 1, 2014

By Joanna Bzówka

Nowadays, there are some new requirements for the supermarket floors. The floors are loaded by high point- and moving-loads. In spite of this fact, it is necessary to ensure the stiffness of the floor and the stiffness of its support. When pile foundations are designed in the case of weak soil, the piles are recommended under the foundations of the supermarket and also under the floor layers. The example of foundation of a typical supermarket located on long­standing municipal dumping ground is presented. Indirect foundation - CFA piles, 0.5 m in diameter and 4.5 to 20.0 m long, was de­signed. Fifteen trial loading tests were carried out.

Jan 1, 2006

By Arpit Parikh

"Ground Water or Pore water pressure development in Sandy Soil formation is Critical situation in foundation analysis and design.Moreover it become severe while associated with higher liquefaction probability in river bank areas. It is difficult to find cost optimized solution for liquefaction mitigation under limited budget allocated for the project. Here in these research paper the attempt has been made to have clear picture of liquefaction by using various techniques and field tests. And its mitigation by suitable foundation type. In Bangladesh, On Bank of River Meghana, Power plant structures are proposed. The particular site is full of fine sand having partial silt throughout from EGL to 55 m depth. Hence in addition to Conventional Boring / Drilling operations, CPLT, SCPT, SCHT and PMT had been performed to arrive deterministic effect of liquefaction. By use of Geologismiki software and some excel based programs developed which indicates that Certainly liquefaction occurs under the event of earthquake. By Checking past records of Bangladesh we found, there are small magnitude earthquakes are inevitable and frequent. Hence fourth to overcome the bad effect of liquefaction, the deep pile foundation -Driven Pre Cast Solid Square Pile of 400 mm dia. had been suggested for various types of power plant structures. Which densify the soil and ground will improve in resisting liquefaction.1. INTRODUCTIONA Detailed Geotechnical/Foundation design Analysis had been done to arrive at optimum foundation design solution in highly probable liquefaction zone of Silty Fine Sand near Dhaka City of Bangladesh for proposed 750 MW Cyclic Power Plant. Hence about 24 no. of (Borehole) Boring and Drilling up to depth of 55 m from existing ground level has been carried out. Additionally, 09 nos. of Static Cone Penetration Test (SCPT), 02 Nos. of Dynamic Cone Penetration Test (DCPT), 02 Nos. of Pressure meter test (PMT), 02 nos. of Cyclic Plate load test (CPLT) of suitable capacity with 06 nos. of Seismic Cross Hole Test (SCHT) in boreholes had been carried out. The purpose of PMT and SCHT was to have clear idea about the Seismic behavior - knowhow of site. According to Basic principles of Soil Mechanics and foundation design, it is proved that PMT & SCHT are dynamic test. These tests stimulate field condition of occurrences of earthquake. In later stages of analysis, it is found that site have high probability of liquefaction through use of Geologismiki – Liquefaction Analysis Software. Author of these research paper also felt earthquake vibrations – strong aftershocks during site study where Epicenter of the earthquake was in Myanmar during month of august 2016."

Jan 1, 2017

By Fritz J. Klingler

From site demolition, to design, to construction, Detroit&apos;s new Tiger Stadium project is required to be completed within a short 2 ½ years from award of the design-build contract. Such extreme schedule requirements together with somewhat difficult ground conditions at the site, resulted in several challenges in the design and construction of the deep foundation system for the stadium. During the geotechnical investigation, an intermittent water bearing sand layer was encountered overlying the hardpan at the site. As a result, some concern developed regarding the potential for collapse of caisson bells within this layer, as well as the potential for flooding of the caissons during drilling. Although sand and/or ground water was encountered within about half of the caissons, standard drilling and belling methods were used, and adverse conditions were controlled in almost all cases through expeditious drilling, inspection and concreting of the caissons. This paper will present a summary of the ground conditions, design and specification requirements, and construction methods used to successfully install the caissons for this project.

Jan 1, 1999

By G. Tamaro

The World Financial Center is situated on a 60,000 square meter site at Battery Park City at the southern tip of Manhattan Island. The foundations for the buildings and the related infrastructure posed difficult design and construction problems since the site was filled land in the Hudson (North) River. Foundation construction was made difficult by both the geology and the existence of two railroad tunnels which passed under the site. The soils at the site were unsuitable to support construction of heavy structures, and as a result, all of the foundations had to be carried down to bedrock, or the glacial till over rock. Two buildings were supported on piling and special battered caissons which provided lateral support against wind loading. The other two buildings were supported directly on rock, requiring excavation to depths of 19 meters (63 feet) below grade.

Jan 1, 1989

By Jean R. Garcia, Paulo J. R. Albuquerque, Renato P. Cunha, Osvaldo Freitas Neto

"Abstract Results obtained from in-situ load tests carried out on drilled displacement piles sunk in a porous, lateritic and unsaturated soil deposit, are analyzed in this paper. Three slow-maintained load tests were performed on deep instrumented piles with a diameter of 0.37 m and around 12 m long. The soil deposit consists of a superficial, silty clay “porous” layer 6 m thick, with an average standard penetration blow count (NSPT) of 4 and cone tip resistance and sleeve friction (qc and fs) of 1.5 MPa and 48 kPa, respectively. Under this layer there is a residual stratum 10 m thick, geotechnically consisting of a “porous” clayey silt with an average NSPT of 7 and qc and fs of 2.4 MPa and 202 kPa, respectively. The water table was reached at a depth of 17 m below ground level. The results of the field load tests yielded a maximum pile load (average for the tests) of 1428 kN, which is twice as high as corresponding experimental values from standard bored piles with similar geometric conditions. Exhumation of one of the tested piles was carried out after the test, in order to check integrity and shaft conditions. Numerical finite element analyses, using the commercially available French Code LCPC Cesar®, were performed in order to back-analyze the geotechnical soil parameters for a post execution pile condition. The results permitted a better understanding of the improvement of the subsoil given the intrinsic execution characteristics of this particular pile. It was also possible to note that drilled displacement piles have great potential to become an economically viable solution in tropical soils, given the enhanced behavior of such piles when compared to alternative (cheaper) techniques. In fact, it has several advantages which should make it a key foundation type in the Brazilian market in the future.IntroductionMost buildings in tropical soils use, as the main type of foundation, deep bored or auger type piles. These types of foundations can be performed in various ways, for example with or without soil extraction, with or without bentonite mud and so on. Two main processes maybe formulated: the first execution process is typified by bored pile types, continuous flight auger piles etc., which do not cause excessive soil displacement during excavation. With respect to the second process, one could mention, amongst others, driven piles (precast concrete or steel), Franki piles and drilled displacement piles, which do displace the soil during excavation by pushing the soil laterally around the hole in order to allow either the penetration of the pile or the excavator auger."

Jan 1, 2014