Search Documents

By Ye Jun

Until now, more than 200 sites of sea-floor hydrothermal activities are known on the midocean ridge but few of them are documented on South Mid-Atlantic Ridge (SMAR). This on some extent restricts our directly understanding of the hydrothermal mechanism on SMAR. In 2011, During the Cruise 22 of R/V Dayangyihao, a masive sulfide field was discovered in the center part of the first-order ridge segment that bounded between Cardno Fracture Zone and Saint Helena Fracture Zone, near 15.16°S/13.35°W, which give us an opportunity to recognize the mechanism of hydrothermal systems on SMAR directly. This newly discovered hydrothermal field, which informally called SMAR 15°S, is situated in a SE-NW offset depression of an axial neovolcanic ridge, with water depth of about 2793m. In the water column around this field, strong turbidity and temperature anomalies were detected. Ten meters high venting chimneys, hydrothermal mounds as well as a large amount of hydrothermal vent shrimps were also observed and recorded by ROV and Deep tow camera on the ocean floor. The samples we collected from this field include sulfide chimney fragments, massive sulfides and basaltic rocks. In this study, we are focusing on the mineralogy and sulfur isotope geochemistry of sulfide samples for preliminarily uncovering the geological characteristics and hydrothermal processes of this hydrothermal field.

Sep 14, 2011

By S. Rajendran

The western continental margin comprises of the southwest coast (Cape Comorin-Mangalore), centralwest coast or Konkan coast (Mangalore-Bombay), northwest coast (Bombay-Gulf of Kutch) and the Laccadives area. Placer deposits of heavy minerals occur in discontinuous patches on the beaches along many parts of the west coast. The richest offshore placer deposits occur along the 25 km stretch of the southwest coast from Neendakara to Kayamkulam. The National Institute of Oceanography (NIO) surveys show that the sediments off the Konkan coast consist largely of silty sand, sandy silt and clay and the concentration of ilmenite is higher than the onshore. The heavy mineral concentration ranges up to 90% and has mainly ilmenite and magnetite with minor quantities of apatite, rutile, zircon, kyanite etc. The heavy mineral sands extend below the clays to water depth down to 20 m. The heavy minerals sands vary in thickness from 2-10 m. Offshore placers can be mined by using wire-line, bucket ladder and hydraulic dredges. Wire-line, bucket ladder and hydraulic dredges. Wire-line dredges may employ drag buckets or clamshell and hydraulic dredges suction or airlift principles. The dredges can be located on flat bottom or catamaran barges. Dredging of very near shore placers may be achieved by operating from land. The bucket ladder type of dredger has greater digging ability and hence can be deployed for mining placers which are partly consolidated or cemented or where the most valuable part of the deposit lies at the contact between the alluvium and the bedrock. This type operates very economically up to 45 m depth and needs minimum power requirement per unit dredged. Suction type hydraulic dredges can be operated very effectively up to 60 m water depths. This system is quite ideal for the inner shelf. The maximum practical economic working water depths for wire-line dredges are about 150 m. With the drag bucket modified into large net buckets, the method can be utilized to greater depths. They can be used in areas of high water currents and swells. The type of bucket can be changed readily with change in the nature of alluvium or substratum. The hydraulic suction dredge is the most suitable system for mining unconsolidated sediments. When the sediments are semi-unconsolidated, a cutter head can be mounted on the lower end of the suction pipe to agitate the seabed.

Jan 1, 1996

By Paul C. Rusanowski

Mining is a waste intensive industry, oftentimes producing hundreds of kilograms of waste rock and tailings for every gram of metal recovered. Disposal of mine tailings is a major concern in most mining operations. In Southeast Alaska the steep terrain and high seismic hazard province limits cost effective opportunities for land disposal of tailings. The lack of infrastructure and long travel distances generally limits secondary utilization of tailings, as well. Since the mines are located close to tidewater, submarine tailings disposal is an attractive option for tailings management. At the present time the EPA will not issue a permit that authorized marine tailings disposal from any mining process that includes flotation technology. Upland disposal is the "Best available technology" and must be used. Consideration of submarine disposal is generally precluded because the tailings are contaminated with fluids from the flotation process. However, when developing technological solutions to minimize environmental disturbance, destruction, pollution, and risk, submarine tailings disposal deserves another evaluation. In Southeast Alaska it may be the "Best available technology" based on an assessment of all issues and concerns in these mining projects.

Jan 1, 1991

By John Noakes

Marine scientists at the University of Georgia, have in the past few years, designed, developed and refined two geochemical survelliance systems for the exploration of hard mineral resources on the seafloor. The one first developed is an underwater sled which contains a nuclear radiation detector for measuring naturally occurring gamma radiation that is associated either with marine phosphorites containing uranium and its decay daughters or thorium decay products that are indicative of monzanite. The latter can, in most instances, be used as a pathfinder mineral for placer deposits that may contain other heavy minerals of interest such as rutile, ilmenite, chromite, gold, etc. This sled is operational in continental shelf depths. The second system is capable of more definitive measurements in the form of direct elemental analyses of the silt and clay fractions within the surficial sediments. It consists of a towed sled containing a submersible pump which, upon agitating the sediments, transfers the finer fraction up a hose to a shipboard centrifugal cone then to an automated sample processor. The resultant samples are rendered into sediment wafers, suitable for non-destructive XRF analysis. The system is capable of shipboard analysis for specific elements within minutes after sampling, allowing a cursory look upon which an exploration grid can be formulated while on site. A much wider spectrum of up to 40 elements can be evaluated when the wafers are returned to the land based laboratory.

Jan 1, 2011

By V. Zaykov

The Urals massive sulfide deposits are concentrated in Silurian -Devonian fold belt extending for 1500 km with length from 50 to 150 km. By paleodynamic reconstmction it is established that they were formed in submarine parts of island arcs, in inter arc and back arc basins, marginal seas. When "black smokers" were found in rift zones of present oceans, problem searching their analogues in the Urals Paleozoic complexes was arisen. For solving this problem and demonstration of seafloor origin of massive sulfide many quarries and drill cores were carefully sketched and studied. Particular attention was given to correlation between ores and synchronous sedimentary rocks and fossils. Various laboratory methods were used for comparing sulfides from ore hills with ore-clastic sulfides.

Jan 1, 1993

By Brian D. Bornhold

A comprehensive multi-disciplinary marine geological survey of northwestern Graham Island, Queen Charlotte Islands, British Columbia, Canada was conducted by Offshore Survey and Positioning Services Ltd. of Vancouver, B.C. on behalf of the Geological Survey of Canada; Energy, Mines & Resources Canada, Pacific Geoscience Centre, Sidney, B.C. Canada during October 1984 and July 1985. The aim of the survey was to map both the surficial geology and geomorphology in order to identify and evaluate the nature of the nearshore sedimentation and recent tectonics including stability (slumps and scarps) seafloor faults (frequency and displacements) and both the classification and consistency of soil type boundaries and properties. Data was acquired by utilizing conventional indirect applied marine geophysical techniques including side scan sonar, precision echo sounding and complimentary soil sampling. During October 1984 a total of 320 line kilometres of data including 180 soil samples were acquired. During July 1985 a total of 300 line kilometres of data were acquired including 150 soil samples.

Jan 1, 1985

By W. H. Pelton

Polymetallic sulphide (PMS) deposits have recently been discovered associated with hydrothermal vents on the sea floor off Vancouver Island, B.C. Visual estimates indicate reserves in excess of 1 million tons. Reliable reserve estimates have not yet been made, however, due to the extreme difficulty of drilling cores in 2 km of water. Few geophysical techniques can aid in the exploration of these deposits. There is little or no difference in radioactivity, magnetic susceptibility or electrical resistivity between the deposits and the surrounding sea floor sediments. This precludes radiometric, magnetic, electromagnetic and resistivity methods. There is a density contrast, but the logistics of gravity surveys at such depths are formidable. The physical property which shows the most contrast with the sea floor sediments, and which is perhaps one of the easiest to measure (with modern equipment) is polarizability. The induced polarization (IP) method is one of the major electrical geophysical techniques for exploring for PMS deposits on land.

Jan 1, 1985

By Peter A. Rona

Hydrothermal mineralization along slow-spreading oceanic ridges and rift -zones that comprise more than half the global length of the seafloor spreading center system is related to anomalous physical and chemical conditions acting within the geologic settings that characterize early and advanced stages of opening of an ocean basin. Mineralization in the early stage of opening is represented by the Atlantis II Deep of the Red Sea. There, hypersaline hydrothermal solutions discharging as density stratified brines into an axial basin, have formed the largest massive sulfide deposit (70 x 106 metric tons) known at a spreading center. Mineralization at the advanced stage of opening is represented by two types of sites: (1) oceanic crust on the wall of a rift valley; and (2) oceanic crust exposed on the wall of a transform fault zone. The first type of site is the TAG Hydrothermal Field, located on a wall of the rift valley of the Mid-Atlantic Ridge at the top of the basaltic layer of oceanic crust. Evidence is presented for multi-stage, high- and low-temperature hydrothermal activity that produces Cu, Fe, and Zn enrichments within the thin sediment column and stratiform interlayered deposits of manganese oxides, iron oxides, hydroxides and silicates, on the seafloor. The second type of site occurs along walls of transform fault zones of the equatorial Mid-Atlantic Ridge and Carlsberg Ridge, which exhibit stockwork-type Cu-Fe sulfide mineralization

Jan 1, 1985

By Patrick J. C. Ryall

Remotely control led drills capable of being lowered to the sea-floor from ordinary research vessels have been developed over the past two decades. These drills are currently being used in geological survey programmes on the continental shelves (Canada, Japan, Norway, United Kingdom) and for studies of mid-ocean ridges. Generally the drills fall into two categories: 1) those which are powered from the surface and controlled by an operator, and 2) those which are battery powered and follow an automatic programme. Some drills have a television camera mounted on them sending a picture to the surface as an aid to site selection and geological interpretation. Typically the drills are capable of drilling a core 2.5 - 5 cm diameter up to 10 m long. While most of these drills are designed for <1000 m depth, some can drill in water depths of as much as 3500 m.

Jan 1, 1985

By P. U. W. Appel

Despite the very large offshore Exclusive Economic Zone (EEZ) area of Greenland (in excess of 2 mill. km2) virtually no work has been carried out on marine minerals on the ocean floor. Apart from a single reconnaissance survey by a mining company, major activities have been those of oil companies exploring the West Greenland shelf in the early seventies. The West Greenland shelf and its extensions is the most obvious area for year-around accessability when looking for marine mineral deposits. So far, only one onshore placer deposit has been found - ilmenite deposit near Thule, NW Greenland, whereas a gold placer in South Greenland presently is being evaluated.

Jan 1, 1988

By D. J. Scarratt

Fisheries make a significant regional contribution to the economy of Canada. In the Atlantic Region, over 70 thousand workers depend on the primary or secondary fishing industry. Fisheries are vulnerable to pre-emption of space by other marine industries and to contamination by chemical discharges. Markets may be affected even by the threat that products may be tainted. Fish may be killed by drags and dredges, and their physiology and behaviour affected by suspended sediments are stirred up by mechanical devices. Virtually no evidence exists of adverse impacts £ran ocean mining on fisheries, but projections from other marine activities such as fishing itself, dredging and other marine discharges give reason for caution. Department of Fisheries and Oceans policy calls for review of ocean mining proposals to ensure adequate protection of fish stocks, fishing activities and fish habitat, and compensation for losses attributable to any industrial project. Adverse impacts can be minimized by careful attention to details of location, technology and timing, and to close co-operation and information exchange between industry and the regulatory agencies.

Jan 1, 1985

By Hunsoo Choi

Internal textures of manganese nodules from Clarion-Clipperton zone of northeastern Pacific Ocean are classified into five textural zones: columnar-textured layered zone, cuspate-textured layered zone, cuspate-textured massive zone, cuspate-textured porous zone and massive- textured massive zone. Vernadite is the main constituent mineral in the columnar- and cuspate-textured layered zone. Buserite sometimes occurs in the cuspate-textured layered zone. The cuspate-textured massive zone is mainly composed of buserite. Todorokite is also associated with buserite in the massive-textured porous zone, where cuspates and globes are partially replaced by massive texture. In the massive-textured massive zone, todorokite, buserite and birnessite occur together. The analyzed elements of all zones are also classified into four elemental groups by the cluster analysis of correlation coefficients: Mn group, Cu-Ni-Mg group, Fe group and Si group. Mn group consists of Mn and K. Cu-Ni-Mg group consists of Cu, Ni, Zn, Mg and/or Ca, Na. Fe group consists of Fe, Co, Ti and/or Ca, P. Si group consists of Si and Al. Each textural zone is composed of three or four elemental groups. These four elemental groups are correlated with mineral composition, such as, Mn group with todorokite, Cu-Ni-Mg group with buserite, Fe group with Co-bearing iron-oxyhydroxide minerals, and Si group with silicates.

Jan 1, 2002

By Johnson R. Cann

Ocean floor sulfide deposits are now known from many parts of the world mid-ocean ridge system and from some seamounts. Clearly they can be expected to occur commonly on the ocean floor. However, only two or three of the known deposits appear to approach the million-ton size, and in none of the deposits has the grade been well-defined. Can knowledge of the processes that happen within the hydrothermal plumbing below deposits help define the conditions under which large, high-grade deposits form? Here I review present knowledge of ocean-floor hydrothermal processes to attempt a first answer to this question. There are three sources of information about these processes. The solutions emerging from active systems must be compatible with patterns of alteration that underlie the volcanogenic sulfide deposits of ophiolite complexes, which are slices of ocean crust thrust onto land. Both of these types of evidence can be linked by computer modelling of the exchange of heat and metals between rocks and flowing water.

Jan 1, 1988

By Alexander Malahoff

Accumulation of cobalt -rich ferromanganese crusts on Pacific seamounts located off-ridge in the Hawaiian EEZ, represents a complex process that involves geologic aging of the seamounts, geographic transportation- of the seamounts on the Pacific plate during the past 80 million years, and geochemical history of the oceans for that period. A comparative study of the building and erosion processes of the young Loihi Submarine Volcano, located south of the Island of Hawaii , and the 80 million year old Cross Seamount, located west of Hawaii , shows that both edifices show wide armchair-shaped talus chutes and intervening ridges of exposed dikes. The similarity between the observed mass wasting process on Loihi and Cross suggests that the slopes of submarine volcanoes are geologically unstable from the time of their origin on the seafloor through their entire geological history. The slopes of Cross are covered by coalesced ferromanganese crust covered talus, steep exposed dike faces, and crust covered dike ridges. A study of the stratigraphy of the crusts shows a range of thicknesses and number of unconformities present. The thickest crusts, up to 8 centimeters, are found preserved within the larger coalesced slabs along the shallower slopes of the talus chutes and along the crests of the ridges between water depths of 400 and 1800 meters. The platinum content was used in stratigraphic correlation between the crusts in the coalesced slabs and those collected from ridges with the PISCES V submersible. In the samples studied, the highest platinum content of 0.7 ppm

Jan 1, 1991

By B. Prause

Ferromanganese crust samples collected from Central Pacific sea-mount areas became of special interest after surprisingly high nobel metal contents have been analyzed. Hydrogenetic crust growth is controlled by the conditions of the oceanic water column. Thicker encrustations show two crust generations of different age ranges. The mean values of the chemical composition state that the older generation is richer in P, Ca, Ni, Cu, Zn, and Pt and depleted in Fe, Ti, Co, Al, and Si. The differences apparently indicate a distinct change of the geochemical environment. The Pt concentrations vary up to 1800 ppb and do not clearly correlate to one of the other metals. This might indicate a bond of multiple nature. Several mechanisms have been proposed to explain the Pt concentrations in ferromanganese samples. Our models consider seawater and cosmic spherules as responsible Pt sources. In seawater the main species of dissolved Pt probably exist as the doubly negatively charged tetrachloro-complex. A precipitation of Pt in seawater may take place if the chloro-complex is decomposed by reduction of pt2+ to pt0. On the other hand, the Mn02 precipitation is caused by an oxidation of Mn2+ which is supplied from the oxygen-minimum zone. The large activation energy needed for the oxidation of divalent ~n" in solution has been recognised, and the resulting slowness in the formation of Mn(V1)-oxihydrate sug

Jan 1, 1989

By Alexander Malahoff

Mineral zonation studies were conducted on hydrothermal vents of two hot spot volcanoes. One study site is located within the Axial Caldera of the axial hot spot volcano of the Juan de Fuca Ridge. The young high-temperature hydrothermal vent field consisting of two polymetallic sulfide chimneys, five meters high, located at 130°01.5&apos;W, 45°56.5&apos;N, along a fault complex at the base of the southwestern wall of Axial Caldera was sampled during four ALVIN dives in 1983. Temperatures of up to 270°C were measured within the orifice of one of the chimneys, which was then broken off and recovered with the submersible. Both black and white "smoke" was observed to be emanating from the one chimney sampled. The high-temperature chimney extends directly from a field of broken lobate lavas which are located at a water depth of 1,550 meters, about 200 meters east of the caldera wall. The chimney makes one of the shallowest active high-temperature vents studied to date. The vent is surrounded by clumps of vestimentiferan worms and is located within an elongate field of red-colored iron smectite blankets and chimneys. The low-temperature field forms a ribbon 150 meters wide, extending for about 1,300 meters at the base of the wall. Chemical analyses of the hydrothermal deposits ranging from the polymetallic sulfides of the chimney to the outer zones of the low-temperature field show a range of elemental assemblages consistent with temperature zonation around the vent. Chemical zonation within the high-temperature

Jan 1, 1988

By Curtis Clement

Williamson & Associates, Inc. has developed a marine mineral exploration tool using an induced polarization technology (IP) under license from the US Geological Survey. Developed by Jeff Wynn at the USGS, this method has gone through several prototyping stages and is now in commercial use to map offshore ilmenite deposits. Preliminary results of a recent resource mapping program are discussed as well as potential applications in the detection and quantification of other minerals in marine sediments.

By Sally Philpot, Siân E. Boyd, Hubert L. Rees, Emma Bee, Carla Houghton, Ceri James, Silvana N. R. Birchenough, S. Limpenny David, A. Coggan1 Roger, Koen Vanstaen

Every year approximately 22 million tonnes of marine sand and gravel are dredged form British waters. The eastern English Channel (EEC) contains substantial reserves, a proportion of which have been identified by the aggregates industry for potential future exploitation. The main aim of this study is to produce broadscale marine habitat maps of the EEC area. The UK aggregates industry has formed a consortium of representatives (the eastern English Channel Association), and have sponsored an initial baseline survey and follow-up sampling programmes as part of a Regional Environmental Assessment (REA) covering a patchwork of aggregate prospecting areas. To complement this effort, a large-scale geophysical survey was conducted in 2005 to place the REA in a wider spatial context and, thereby, to help assess the environmental significance of any future impacts arising from commercial aggregate extraction over the broader region of the EEC.

Sep 24, 2006

By Richard T. Haworfh

The United Nations Convention on the Law of the Sea (UNCLOS) entered into force, for those nations who had ratified it, on November 16, 1994. The Convention deals with nearly every aspect of ocean affairs, including marine scientific research, fishing zones, freedom of the high seas, protection of the marine environment and deep seabed mining. Article 76 of the Convention defines edge of the continental shelf in a way that many earth scientists find bizarre. Out to this limit, a coastal state has sovereignty over the seabed and sub-seafloor resources. Beyond that limit, the key principle of UNCLOS, that "the resources of the deep seabed represent the common heritage of mankind and should be developed to benefit all nations" is invoked. Establishing that limit and managing development in the different areas of jurisdiction is no small task. Canada&apos;s continental shelf as defined by UNCLOS covers an area approximately equal to half the area of the Canadian land mass. Interpretation and application of the convention is therefore highly significant for Canada. For example, the sedimentary basin in which the offshore Hibernia oil field is found, extends beyond the 200 mile limit but lies predominantly within the limits of the (UNCLOS) continental shelf. Responsibility for development of inshore placer deposits rests firmly with the coastal state. However, development of deep sea mining, in which the international community plays a management role under UNCLOS, has raised many concerns. Of particular interest to Canada will be the application of the provisions of the convention to interest in the polymetallic sulfides sampled on the mid-ocean ridges such as the Juan da Fuca Ridge. A further complicating factor for Canada is management of fishing stocks. Canada has sought to resolve this "problem" through multilateral negotiations under the UN. Under its "Oceans Act," currently being debated by Parliament, Canada intends to become a world leader in oceans and marine resource management. Similar activity in most maritime nations is setting the stage for a revolution in the way in which use of the world&apos;s oceans is managed. Much of this revolution will be guided by UNCLOS. Coastal states that have ratified the convention have ten years in which to define the limits of their continental shelves the clock is already ticking for them! We have yet to see how their actions will guide, or be guided by, those who have not yet ratified. We also have yet to see how national legislation and aspirations will mesh with international conventions that were drawn up in a previous era of environmental standards. This is a time in which many questions have been raised and few firm answers received. However, we must ensure that everyone is aware of what is happening, with what potential consequences, in order that rational decisions can be made. Canada has taken a few small steps that it is happy to share with the world community.

Jan 1, 1996

By Randolph A. Koski

Since 1985, numerous constructional sulfide-sulfate deposits in the form of mounds, pinnacles, chimneys, and sheets have been located between 40°45&apos; and 41°05&apos;N latitude in Escanaba Trough, the sediment-covered axial valley of the Southern Gorda Ridge. Single-channel seismic data indicate that three volcanic edifices up to 6 km in width penetrate as much as 500 m of turbidites that fill the valley; pillow and sheet flow lavas are exposed on the sea floor where these volcanoes breach the sediment surface. Observations from deeply towed camera systems and submersibles show that the largest hydrothermal deposits occur along the step-faulted northern flank of the central volcanic edifice and on the peripheries of steep-sided, sediment-capped hills, approximately 1 km wide and 100 m high, that rise above the valley floor. The sulfide deposits are highly oxidized, eroded, and partly buried by unconsolidated sediment; aprons of sulfide talus extend downslope from the mounds. Two types of sulfide have been sampled by dredging and submersible. The predominant mound and chimney material is pyrrhotite-rich massive sulfide with low amounts of Zn, Pb, Cd, and Ag. Coarse-grained zones with high porosity mark the location of myriad fluid channelways. Thin crusts of barite associated with pyrrhotite-rich sulfide have Au contents up to 2 ppm. Zoned fragments of polymetallic (Fe-Zn-Pb-Cu-As-Ag-Sb) sulfide dredged from a single site near 41°01&apos;N latitude are part of a chimneylike vent structure with a

Jan 1, 1988