Search Documents

By C. Y. Wang

Based on Slurry Electrolysis, and combined with the problems of extraction antimony, lead and their separation from complicated antimony-lead concentrate, a series of tests have been done in this paper. Using Slurry Electrolysis to treat complicated antimony-lead concentrate, antimony and lead can be separated in one step. And 2# metal antimony can be achieved in cathode directly at the same time. Lead in concentrate is restrained still in the residue at the form of PbCl2. After converting the residue with ammonium carbonate and removing sulfur with kerosene, the high quality of lead concentrate (Pb is above 45%, S is below 15%) and pure sulfur can be achieved, respectively. The recovery of all in Slurry Electrolysis process is as: Sb 95%, Pb 95%, Ag 80%, S 60%.

Jan 1, 2014

By J. Yianatos

The regrinding stage is necessary to achieve the particle size (liberation) for the final upgrade in the cleaning flotation process. At present, vertical mills (Vertimill) are employed at industrial scale, using small steel balls as grinding media. The regrinding process characterization requires mixing regime knowledge along with the mean residence time of the liquid and solid phases. The residence time distribution (RTD) and the actual mean residence time estimations from theoretical relationships are complex due to the presence of three components (solid mineral, balls and water), mass transport characteristics and segregation affecting solid holdup. Therefore, the experimental RTD determination is suitable for industrial mills. In this work, RTD measurements were performed in two different industrial flotation plants. Both plants operate with Vertimills of 1000-1500 HP in the regrinding process with different circuit arrangements according to the plant treatment capacity. The RTD was measured using the radioactive tracer technique. This technique allows for non-invasive tracer detection where the procedure consists of selecting a liquid (Br82 in aqueous solution) or solid (irradiated solid) tracer for RTD data acquisition in real time. The RTD was modelled by the Large and Small Tanks in Series (LSTS) model, which allowed the characterization of the different mixing regimes for both liquid and solids in the regrinding mills. Effective mean residence times in the range 2-11 min were obtained with RTD shapes similar to those obtained in tumbling ball mills. It was found that residence times of liquid and fine particles were similar, which is consistent with results observed in other mixing systems, e.g. mechanical flotation cells. Also, the mean residence times estimated from the RTD allowed the mass balance adjustment to be validated from metallurgical sampling data. RTD estimations are useful for better understanding the Vertimill behaviour and to identify the actual breakage rates. Keywords: vertical mill, residence time distribution, particle size, modeling

Sep 1, 2012

By Ljudmil S. Grigorov, Eric Forssberg, Hanumantha Rao Kota, Robert J. Pugh, Lidia B. Alexandrova

"We have used the microscopic thin balance developed by Scheludko at al. (1970) technique to study the stability and interactions within the thin film between the silica surface and air bubble with (i) a long chain C10 amine and (ii) a cationic/anionic surfactant systems consisting of mixtures of a long straight C10 chain amine with long straight chain C8, C10 and C12 sulfonates. It was found that the mixed surfactants caused lower contact angles, lower rates of the thin aqueous film rupture and longer film lifetime, compared to the pure amine system.This behavior was explained by the initial strong adsorption of positively charged interfacial complexes from the mixed surfactant system at the air/solution interface followed by adsorption at the silica interface. It was also shown that the chain length compatibility between the anionic and cationic surfactants controls the strength of the interfacial complex, determining an inhibition in the thin film rupture and dewetting of the film. The rupture mechanism was explained by an earlier established heterocoagulation mechanism between the positively charged air/solution interface and the solution/silica interface which remained negatively charged. The formation of the interfacial complex at the air/solution interface was confirmed by using surface tension data."

Jan 1, 2003

By I. V. Shadrunova

Annually it is formed more than 95 Mt of clinkers in iron and steel industry of Russia, including 79 Mt of clinkers in blast-furnace, steelmaking, foundry and ferroalloy productions. Complex development of clinkers will provide not only extraction of valuable components, but also preservation of ecosystems. Processing of solid slags is realized, as a rule, in a cold condition by mechanical methods only including stage-by-stage crushing of slag on devices, working on principles of compression and shift (jaw and roll crushers). However it doesn?t provide the complete extraction of metals from clinkers. The intensification of decomposition, in our opinion, can be provided under the use of the devices working on a principle of free kick. At such influence on a material, its destruction occurs on micro cracks, sides of cohesion that is there is a selective destruction of the components possessing various resistances to impact. Decomposition of a piece on the basis of free kick about a material or metal is realized in centrifugal-shock crushers and mills of research-and-production association ?Ural Center?. The share of the joints sharply lowering the efficiency of enrichment thus is minimal. The efficiency of application is proved by morph-metrical measurements with the help of system of image analysis ?SIAMS-600? and physical-mechanical tests of clinkers and their components (impact strength, micro hardness). The experience of application the devices of centrifugal-shock crushing for processing clinkers in blast-furnace, martin and converter productions of Open Society MMC, clinkers of rough-edged copper melt of Joint-Stock Company "Karabashmed" and aluminium clinkers of Joint-Stock Company « Samara plant of aluminium alloys » has allowed to confirm the efficiency of application these devices for selective decomposition of metallurgical clinkers and the opportunity of using clinkers as resource of ferrous and nonferrous metallurgy.

Jan 1, 2014

By T. N. Alexandrova

Results of mineralogical-technological research of carbonaceous rocks of Kimkansky precious metal occurrence are presented, on their basis new typemorphic natural and technological microelement associations were revealed using mathematical statistics methods. Keywords: carbonaceous rocks, processing, microelements, flotation, statistical criteria

Sep 1, 2012

By S. J. Neethling

"This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another. In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system.s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries.A final interesting result is that all the effects examined affect the process to a similar degree, which implies that none of these variables can be disregarded, either in industry or in further research."

Jan 1, 2003

By H. J. Wu

The optimum performance in mineral processing plants usually demands the optimum size reduction, which is frequently achieved by a closed grinding circuit. Due to the difficulty associated with fine size classification, the size separation efficiency in closed grinding circuit is usually very low, which leads to huge circulating load and significant overgrinding. Recent development of Der-rick Stack Sizer has made an efficient fine size separation down to 200 mesh with a satisfactory screening capacity. With the efficient fine size separation with Derrick Stack sizer, the problems commonly associated with typical closed grinding circuit, including high circulating load and over-grinding, have been eliminated. Feedback from numerous Stack Sizer applications in iron ore industry indicated that, compared with conventional fine size classification equipment, the circulating load achieved by Derrick screen was usually decreased from approximate 300% down to 60% or so, while the iron recovery has been increased by 6% to 8% only by more efficient size separation in the closed grinding circuit. To study this phenomenon, this paper discusses the relationship between size classification, circulating load and mineral recovery in the closed grinding circuit. A simulation model to predict the improvement in the grinding circuit from more efficient screening is also introduced with this paper.

Jan 1, 2014

By P. Somasundaran

Treatment of mineral surfaces with appropriate surfactants plays an important role in mineral processing operations such as flotation, flocculation and dewatering. Recently biosurfactants, in particular, have received a considerable amount of attention because of their unique surface active properties and biodegradability. In this work we examined the performance of biosurfactants, sugar based alkyl glycosides and sophorolipid esters as reagents to control the hydrophobicity of minerals with selectivity of adsorption on mineral surfaces for flotation applications. It was discovered that n-dodecyl-ß-D-maltoside adsorbs on alumina, titania and hematite but, interestingly, not on silica. The hydrophobicity obtained is governed both by the surface coverage as well as the nanostructure of the adsorbed layer in terms of orientation of the adsorbed species. Surprisingly, even though the above surfactants are non-ionic, their adsorption was pH-dependent. We have correlated this pH dependence to the type of species on the mineral surface. Also it is shown that mixing of these surfactants with traditional ones can help reduce the carbon footprint due to synergy between the reagents and help selectivity due to antagonism. The experimental results were analyzed to get information on optimal pH and dosage conditions, for mineral surface modification. The study provides guidance for mineral treatments using biosurfactants and the potential use of these next generation reagents in mineral processing.

Jan 1, 2014

By W. Pawlos

"The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images.Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement. The outlet level of a grain of the same physical properties from the separator is a random variable with normal distribution which modal value is equal to the outlet level of a spherical grain, calculated from the solution of grain movement equations. At these assumptions it is possible to calculate the height of the passage from the separator working chamber to separate a given product with a given separation accuracy, measured by a probable error and to determine separation conditions."

Jan 1, 2003

By Y. Rama Murthy

Around 90% of the chromite resources of India are concentrated in the Boula-Nuasahi Sukinda belt of Orissa state. In order to conserve these valuable ore resources strategically, several companies established chrome ore beneficiation plants in this region. The general beneficiation process in these plants consists of gravity unit operations such as Floatex density separator, spiral, wet shaking table etc. Most of these gravity circuits suffer huge losses of valuable minerals in the tailing. Any attempt towards decreasing these losses would not only increase the limited reserves in India but also make the economics of the operations more attractive. Apart from the liberation phenomena, in many of the operating plants considerable quantity of values are lost in the tailings, due to inconsistent feed quality, inappropriate selection of operating and design parameters. Mineral engineers in this regard have to play a proactive and continuous role to improve the performance of all separating units by modifying even small changes based on tests conducted in laboratory under controlled conditions followed by attempts to make necessary changes in the plant. For such improvements, accurate data collection and proper data interpretation followed by making necessary change which is implementable in an operating plant play a very critical role in performance of the circuit. Databank collected over a period of time under various conditions would also help in overcoming the future problems related to either variation in the feed characteristics or specific demand by metallurgical industries. The above concept was adopted in one of the operating chromite beneficiation plant at Sukinda. The approach adopted and practical problems encountered during the study were reported in this paper. The result of trial campaign has shown that, an overall product assaying 30.2% Cr2O3 from the feed (18% Cr2O3 ) can be produced to in single stage. The final discards of the process contain 12% Cr2O3. Keywords: chromite, chromite beneficiation, chromite losses, gravity concentration techniques, plant operating data bank

Sep 1, 2012

By Ruiyang Zhang, Ping Fang, Dezhou Wei, Shuling Gao

A CFD based numerical simulation of flow characteristics of hydrocyclone was conducted with different structural and operational parameters to investigate its distribution characteristics and influencing mechanism. The results show there exist several unsymmetrical envelopes of equal vertical velocities among both upward inner flows and downward outer flows in the hydrocyclone, and cone angle and apex diameter have remarkable influence on the vertical location of the cone bottom of the envelop of zero vertical velocity. It is also found that some tangential velocity isolines exist in the horizontal planes located in the effective separation region of hydrocyclone, and feed pressure has almost no effect on the distribution characteristics of both vertical velocity and tangential velocity of flow in hydrocyclone, however the magnitude and gradient of tangential velocity are made increased obviously, so as to make the high density particles motion velocity to the wall increased and to make the cyclonic separation effect improved. The simulation results also show when the apex diameter increased, the pressure of the fluid field decreased, however the pressure grads in the apex district increased, and the degree of changing is different as the cone angle, which showed some interactive influence of cone angle and apex diameter on the fluid field of hydrocyclone. While the feed pressure also has almost no effect on the pressure distribution characteristics, however the its magnitude and gradient are made increased accordingly, which can improve the separation accuracy according to particle density.

Jan 1, 2014

By M. Schneider, J. Regler, Th. Neesse, AKW A. + V GmbH & Co., J. Dueck, F. Donhauser

"In practice the advantages of high-quality hydrocyclone separation are often reduced due to varying feed suspension properties, solids concentrations and particle size distributions. Therefore, a new control system for a battery of hydrocyclones with a nominal diameter of 150 mm was developed for bentonite slurry regeneration associated with tunnel excavation using bentonite slurry as a transport aid and lubricant.As can be seen from Fig. 1, the hydrocyclone battery has been modified for regulation purpose. The battery was manufactured with an overflow collector as a closed pressure chamber (1) with a discharge pipe (2) where the throttling valve (3) was installed.With increased stepwise throttling of the overflow, the volume split is changed with the effect that the solids discharge in the underflow is increased. To stabilize the total throughput, the feed pump speed is simultaneously increased so that the pressure drop ?p across the hydrocyclones (9) remains approximately constant. However, this causes the increasing pressure inside the hydrocyclones, which results in a further intensification of the underflow discharge. After the detection of the break through of the air core (transition state) by the capacitive sensor (4), the throttle valve is shortly opened, and a new regulation interval can start again. The control concept is focused on maintaining the optimum operating state, characterized by the underflow discharge shape at the transition state between rope and umbrella discharge."

Jan 1, 2003

By D. Pirouzan

It is customary to use more than one stage of flotation to obtain an acceptable level of separation of valuables. Flotation circuit design is usually accomplished by applying empirical rules which usually results in operations not working at their optimum conditions. Given the capabilities of genetic algorithms (GA) in finding an optimum solution in a very disturbed search spaces, they can be used to obtain the desired flotation circuit configuration. In flotation circuit configuration and optimization problem, a combination of metallurgical parameters such as yield and concentrate ash content could be used as the fitness function for the genetic algorithm. The multi-objective nature of the problem justified to use Pareto method to arrive at a set of solutions. The appropriate configuration based on technical or economical considerations could then be chosen. To obtain the fitness function for any given configuration, it is necessary to model every flotation stage. The proposed method was used to find the optimum circuit configuration for a coal washing plant. The objective was to arrive at the highest yield while producing a concentrate with a certain ash content (< 11%). The feed to the flotation circuit was characterized based on the size fractions and their flotation rate constants. Results showed that with a 95% confidence, the absolute difference between the modeled and measured values were 2.9-5.5% for yield and 0.4-1.1% for concentrate ash content. When the proposed GA-based circuit configuration was implemented in the plant, the yield increased from the original value of 57.6% to 65.7% while producing concentrate ash content (10.9%) within acceptable limits. By adding one stage to the current three-stage circuit, it was predicted that the yield could further increase by 3.8% while keeping the quality of the concentrate within the appropriate level. Keywords: modeling, optimizing, flotation circuit configuration, genetic algorithms

Sep 1, 2012

By E. Vahidi

In this study, a hydrometallurgical treatment involving solvent extraction of zinc using D2EHPA (di-2-ethylhexyl phosphoric acid) has been investigated to recover zinc from an industrial zinc leach residue. The residue was leached with sulfuric acid producing leach liquor which was subjected to solvent extraction for enrichment of zinc and removal of impurities. Operating variables for the zinc extraction process, such as pH of the mixed solution (0.5~5.0), concentration of D2EHPA (5%~40%, w/w), temperature (25~60°?C), A/O volumetric phase ratio (1/2~4/1), concentration of tri-butyl phosphate (TBP) as modifier (3%~7%, w/w), concentration of NaR2RSOR4R in aqueous phase (0.05M, 0.1M, 0.2M) were also studied. Practically all zinc was extracted from the aqueous solution at pH 2.5 with 20% w/w D2EHPA in kerosene. At this operating condition, zinc could be extracted at one theoretical stage at A/O phase ratio of 1/1, as calculated by the McCabe-Thiele method.

Jan 1, 2014

By M. Ghiani, R. Peretti, S. di Giovanni, G. Zonnedda, A. Serci, A. Zucca

"Beneficiation of the epithermal gold mineralizations associated with an extensive alteration zone in the Serrenti-Furtei region on the island of Sardinia, is proving a complex issue. Experimental investigations have in fact demonstrated that while the ores contained in the upper parts of the deposit are amenable to conventional cyanidation, the gold contained in the refractory ores in the lower portions needs to be recovered by means of flotation, combined with leaching where necessary.The results of commercial heap leaching, carbon-in-leach (CIL) processing and flotation, designed on the basis of the experimental findings and applied to the oxidized portions and transition zones of the deep sulphide mineralizations, confirmed the expectations emerging from the laboratory tests."

Jan 1, 2003

By T. Khonthu

The purpose of this investigation was to evaluate the relationship between different milling procedures, viz. a ball mill and an IsaMill respectively, and the flotation performance of the different mill products. Two ores were used, viz. a base metal sulphide (BMS) and a platinum group mineral (PGM) UG2 ore. Flotation was used as a diagnostic to investigate whether the different milling procedures may have different effects of the floatability of the particles. The present study is part of a research programme investigating this question using a wide range of comminutiondevices and procedures. Similar particle size fractions from the different milling procedures were used in the flotation tests. The particles were characterized in terms of particle size distribution, morphology (using scanning electron microscopy and image analysis software) and rheology tests. The results have shown that in general when comparing similar feeds to flotation in terms of equivalent particle size distributions as indicated by the d80 value, the ball mill generally yielded better recoveries and grades in the case of the BMS and lower chromite recoveries in the case of the UG2 ore compared to the IsaMill. No significant differences were observed in the morphological or rheological characteristics of the particles subjected to the different milling procedures. Although the results appear to indicate that IsaMilling is less advantageous than ball milling in terms of the flotation performance for the two ores studied it should be emphasized that these results do not take into account the relative advantage which IsaMilling has over ball milling in terms of direct and indirect energy consumption and GHG emissions nor, most importantly, does it consider the platinum group element recoveries in the case of the UG2 which may have increased significantly as a result of the finer grind which the IsaMill produces after 4 passes compared to the ball mill after 64 min. Such results which will be reported is due course may show that the greater liberation expected after IsaMilling of the PGMs outweighs any disadvantages indicated in this study.

Sep 1, 2012

By Stefaan J. R. Simons, Michael T. Spyridopoulos

In this paper the effect of humic substances (natural surfactants), electrolytes and solid particles on bubble coalescence, and as a consequence on froth stability, has been investigated. We formed two bubbles of equal size and forced them to collide using a novel experimental apparatus. The interactions were recorded by a high-speed camera, the images of which helped to determine the coalescence frequency and the coalescence time, as well as the mechanisms of the interactions. Two types of humic substances were used, along with three different electrolytes. Humic substances appeared to have a considerable effect on bubble coalescence, while the effect of electrolytes was minimal. Moderate and high hydrophobic glass spheres were used between two bubbles. Very hydrophobic spheres promoted fast bubble coalescence, while moderate hydrophobic spheres had no effect. We present data of coalescence frequency and time, as well as images of the coalescence events.

Jan 1, 2003

By B. Das

Waste water produced from coal preparation plants posses several problems during dewatering and solid/liquid separation. The natural sedimentation rate of the particles present in colloidal and finely divided suspended form is very slow. Flocculation technology is being applied in most of the coal washeries to recover water which is being accomplished through the use of inorganic salts, polymeric flocculants or both depending on the chemical and physical characteristics of the pollutants present in the waste water. The waste tailing water from Piperware coal preparation plant, Central Coalfield Limited (CCL), India, is highly turbid containing ~ 16000 NTU with negative surface charge in the pH range of 2 to 10. Polymeric flocculants in conjunction with fine magnetite is investigated to achieve faster settling rate with lowest level of water turbidity. The conditions affecting the interaction between the reagents and the turbid particles present in the tailings water are investigated. It is possible to bring down the turbidity of the water to < 90 NTU from very high turbid tailing water by using 2 mg/L of the polymeric flocculent in combination with 0.1 g/L of magnetite at natural pH of the tailing slurry. It has been found that finely divided positively charged magnetite particles in combination with the flocculent selectively coat the negatively charged impurities present in water and thereby increase the settling rate under the influence of a magnetic field.

Jan 1, 2014

By Roberto Galéry, Braz J. C. Filho, Marcelo M. Stopa, Douglas B. Mazzinghy, Priscila M. Esteves

"The purpose of the research is to monitor ball mill filling by means of signals usually measured in its electrical drive. The method is based on the mill torque estimated from rotor speed and induction motor stator voltage and currents. New signal processing is presented in both time and frequency domain for measurements in a dry laboratory ball mill. Statistical analysis is applied to time series resulting in good correlation to mill filling. Fast Fourier Transform (FFT) and power spectral density (PSD) also resulted in an accurate filling indicator. The proposed method does not need any sensor to be installed directly on the mill and requires only sensors usually available for motor control purposes. The experimental results showed that the method have potential to be used to construct an automatic system for monitoring operational variables in ball mills. The aim of this monitoring is to improve energy efficiency, reliability and productivity.INTRODUCTION Recently, a great number of papers have pointed the importance of ball mill filling monitoring and also of grinding control (Lu, et al., 2014) (Ramasamy, et al., 2005) (Tsamatsoulis, 2014) (Zhou, et al., 2009). Additionally, great amount of control techniques have also been presented with several complexity degrees (Tsamatsoulis, 2014). According to Eremenko (2015) the lack of effective and accurate methods for fill level measurement is the main reason that makes mill optimal control so complicated. It happens because nonlinearity, long time delay and time varying features of the ball mill turns difficult to develop a truly efficient method for monitoring filling. At the same time, fill level has a determining role in charge motion and consequently on particle breakage. For low levels of filling many energy is expended in impacts with very low breakage efficiency. Those impacts can also damage mill liner. In contrast, high levels of filling causes damping effects that reduces breakage and can also affect energy consumption. Based on this it is conclusive that fill level measurement of ball mills is an important issue for grinding efficiency. This fill level information can be used for operators to control ball mills and also for engineers to run simulations and improve confidence levels of circuit designs (Shi, 2016)."

Jan 1, 2018

By F. A. V. Guimarães, A. M. Costa

"The moisture in sintering is a very important parameter for the performance of the process. It allows that the granulation takes pace in an efficient way making the water bridges between the bigger particles used as nucleus and the finer particles that perform the coating of those coarse particles. The formation of the micro pellets is extremely important to prevent loss in permeability of the bed in the sintering grate, avoiding excessive fuel consumption and producing a quality sinter. The aim of this project is to use some of the methodologies for determine the saturation degree on ores and coal to determine the optimal moisture for sintering. In the sinter pot grate series, 3 to 4 assays in a series of 10 are required to determine the optimal moisture for the process. The saturation degree curve test has shown that is really viable to use this technique to skip those tests and go directly to the series to determine productivity and the coke / anthracite consumption. In an industrial scale can be used to adjust the water addition in the conventional mixing methods used in the sintering plants to increase productivity in the process.INTRODUCTION Sintering Sintering is a high temperature agglomeration process in which iron ore fines are partially melted and bonded together using fluxes and a source of fuel, usually coke breeze. The agglomerated product, sinter, has improved metallurgical properties making it an ideal ferrous burden that enable the passage of hot gases in the iron-making blast furnace. The sintering process is normally carried out over three basic stages: granulation, ignition/sintering, and product sizing. In the granulation stage, iron ore fines (usually a blend of selected ores), sinter return fines, fluxes and fuel, and are mixed with water and micro-pelletised in a drum or disc before being introduced in the main granulation circuit. (Wang, Teng, & Wang, 2017)."

Jan 1, 2018