Search Documents

By Arkady Senchenko, Andrey Vasiliev, Alexander Aksenov, Metodi Zlatev

"This paper considers the issue of treating argillaceous oxidized ores with low gold grade (around 1.0 g/t). These ores according to their gold recovery level can be treated by heap leaching and agitation cyanide leaching, but low gold grade makes this treatment uneconomic. Heap leaching of argillaceous ores requires high consumption of binding agent for pelletizing to create suitable hydro-physical properties of material, which leads to increasing process cost and makes the material treatment unprofitable. Agitation cyanide leaching of this ore requires grinding processes; these expenses would not be paid back by the amount of gold recovered. Considering the above, poor argillaceous oxidized ores are recommended to be treated according to a combined technology including fractionation of ore, heap leaching of coarse fraction and agitation leaching of argillaceous fraction. Complex approach application allows one to avoid expenses incurred for material grinding and high consumption of binding agent for pelletizing. The success of this technology implementation will firstly depend on the quality of material fractionation, therefore the section of disintegration and division of ore into different components will be the most important part of flowsheet development for gold production. When disintegrating minerals at positive temperatures both standard (mechanical disintegration - scrubbers) and innovative (hydraulic method of disintegration - HydroClean units) equipment is applicable. HydroClean units are characterized by lower energy and water consumption. In a number of cases it is required to treat frozen ores. When treating frozen material standard approaches to disintegration are not reasonable due to their low efficiency. In order to treat frozen material a two stage disintegration flowsheet with screening after each stage is recommended. The first stage is recommended to be performed in a scrubber, the second - in a HydroClean unit. This technological flowsheet will provide high and steady values for ore separation into fractions at low energy consumption for disintegration."

Jan 1, 2014

By Y. Q. Qui

In the bauxite flotation process for desilication, the middling treatment mode is the important factor to raise the flotation recovery of the preparation concentrate. The middling treatment mode mainly depends on A/S and the size composition. However, similar ratio of A/S should not be the single factor of re-dressing, size composition plays an important role also. Re-dressing the middling mixed with the tailings of concentrated to the rough ground for desilication and the concentrate of scavenged to the fine ground for desilication to raise the recovery of 5.83%, when compared two flow sheet schemes.

Jan 1, 2014

By Shibayama A.

In this research, an investigation of a process to selectively remove arsenic (As) and antimony (Sb) contained in enargite (Cu3AsS4) and tennantite/tetrahedrite ((Cu1,Fe)12(As,Sb)4S13) copper resources by leaching and precipitation were performed. First in the leaching process, the target was to selectively leach As/Sb and reduce their contents in the ores to <0.5 wt% followed by a second process to remove As/Sb dissolved in solution for environmental control. Enargite ore contained 3.65 wt% As while tennantite/tetrahedrite ore contained 5.40 wt% As and 4.85 wt% Sb. Alkaline leaching using NaHS?NaOH media at varying experimental conditions (temperature, pulp density, time, reagent concentrations) were performed to investigate the process. As/Sb precipitation studies were also performed to control high As/Sb concentrations in leach solutions by using elemental sulphur (So). Results from leaching studies showed that over 99% of As/Sb in the impure copper ores can be removed and their contents in the final solids reduced to <0.5 wt%. It was also established that such very high leaching could be achieved at 80°C within 1?6 h and pulp densities as high as 1000 g/L. The study also revealed that leach solution containing very high As/Sb concentration ranging from 5 to 20 g/L can be used as fresh solution for leaching of fresh ores until concentrations exceeding 35 g/L when it was sent to precipitation circuit for As/Sb removal. Addition of elemental sulphur at 90°C and fast cooling to 30°C allowed over 60% As/Sb precipitation and removed as Na3AsS4 and solution with reduced As/Sb concentration to leaching circuit for continuous use. Keywords: Enargite; Tennantite/Tetrahedrite; Selective Leaching; Precipitation; Sodium hydrosulfide;

Sep 1, 2012

By Rodney J. Hundermark, Sharif Jahanshahi, Shouyi Sun

"The major platinum producers in South Africa make use of electric furnaces for the melting of PGM bearing nickel - copper concentrates. To gain better understanding of the furnace operation, research was conducted at CSIRO Minerals in Melbourne, Australia. One aspect of the research project was the investigation of the factors affecting the electrical conductivity of melter type slags.Electrical conduction in slags can occur through two mechanisms: ionic and electronic. There is good understanding of the ionic mechanism. In slags containing high levels of iron, the dominant mechanism is electronic. There is limited understanding of the electronic mechanism and one of the aims of the research was to investigate this mechanism further.Experimental work was carried out on Al2O3.CaO.FeOx.MgO.SiO2 slags similar in composition to the melter slags. Conductivity increased significantly with iron oxide content. Above 20wt% FeOx, electronic conduction was significant and the conductivity varied with the oxidation state of the slag. As the iron oxide content was increased further, the electronic mechanism became more dominant. The conductivity reached a maximum at around pO2 = 10-7 to 10-4 atm., although this value was dependent on the total iron oxide content and basicity of the slag."

Jan 1, 2003

Much has been published in recent years on the challenges facing the engineer of the 21st century and the consequent challenges facing the education providers and industry. The world is changing rapidly on the social, economic, political, technical and environmental fronts and our metallurgists/mineral processing engineers of the future will arguably need to have a different set of skills than those which were traditionally regarded as adequate during the latter half of the 20th century. This paper attempts to explore some of these issues and their ramifications.

Jan 1, 2014

By P. T. L. Koh

The effect of particle shape on the flotation process has been investigated in laboratory experiments with monosized spherical ballotini and roughly ground ballotini. The particles were treated by partial methylation with trimethylchlorosilane to achieve varying degrees of hydrophobicity. In flotation, the process of film thinning and liquid drainage is critical in the formation of a stable bubble-particle attachment and this is affected by the particle shape and surface hydrophobicity. The rate of attachment affects the overall flotation rate. Flotation tests with different particle sizes at various degrees of partial methylation have been performed in a modified Denver cell. Predictions from a computational fluid dynamic model of the cell which incorporates fundamental aspects of bubble-particle attachment are compared against flotation test results. Contact angles of the particles have also been measured using the capillary rise technique to indicate surface hydrophobicity.

Jan 1, 2014

By G. Venkateswara Rao

The multi-gravity separator (MGS) is a novel piece of equipment for the separation of fine and ultra-fine minerals. However, the published literature does not demonstrate its use in the separation of Iron ore fines. Therefore, an attempt was made to study the effects of different process variables on the performance of an MGS for the beneficiation of Iron ore fines. The results obtained from this study revealed that among the parameters studied, drum rotation, amount of wash water and angle of inclination play dominating roles in controlling the yield and grade of the Iron ore. The majority of the newly developed Multi gravity concentrators have tremendous potentials for various applications. Therefore, the performance evaluation of these concentrators treating various minerals, coals, heavy metal recovery from tailing dams, etc., have become an active research topic. Several attempts have also been made to develop appropriate mathematical models of individual concentrators. Despite all these efforts, these concentrators have yet to find the widespread applications they deserve. The ?as received? sample assayed 40.80% Fe, 40.90% SiO2,0.24% Al2O3and 0.20 % LOI and all other trace elements within the specified range. The current paper deals with the Mineralogical studies, characterization and process amenability studies of Sub grade Iron ore from Deposit No. 5, Bacheli complex of Bailadila using Multi Gravity Separator (MGS).

Sep 1, 2012

By Hong Zhong, Shuai Wang, Zhanfang Cao, Ting Dai

"Manganese is widely used in industries such as the steel industry and is now an essential element in modern industry. Technologies for the efficient and clean utilization of manganese resources must be developed and employed to ensure the sustainable growth of the manganese industry. Our research focuses on the use of beneficiation technologies to improve the grade of ores or the replacement of low-grade manganese carbonate ores with high-grade manganese oxide ores, and thus, to reduce reagent and energy consumption and the yield of electrolytic manganese residues from metallurgical processes; the study of leachate purification technologies; the study of electrochemical behaviors during electrolysis and energy-saving electrolysis methods; the development of chromium-free passivators as alternatives to the highly toxic potassium dichromate passivator; the non-hazardous treatment and resource utilization of electrolytic manganese residues and other manganese by-products; and the development of new manganese products. INTRODUCTION Manganese is widely used in the steel industry, nonferrous metallurgy, the chemical industry, electronics, batteries, agriculture, etc. Globally, more than 90% of manganese is consumed by the steel industry, and thus, it is said that ""No steel industry without manganese""(Banerjee et al. 2017, Zhang et al. 2017). Current manganese resources mainly include manganese ores, marine manganese nodules and waste catalysts. The total global output of manganese ore from land deposits is 18 million tons (metal volume), and the reserves, most of which is in the form of manganese oxide ores, are estimated to be 620 million tons (metal volume). More than 400 manganese ore deposits with a total reserve of 1.22 billion tons have been discovered in China. These deposits are predominantly manganese carbonate ores. Marine manganese nodules exist on the surface of the deep seabed at depths of 2000-6000 m. These nodules, which are also called polymetallic nodules, manganese balls, manganese aggregates and manganese tumors, are mainly composed of iron and manganese oxides. The total reserves of these resources add up to more than 3 trillion tons. Furthermore, the manganese in manganese-containing catalysts can be recycled after they become inactive."

Jan 1, 2018

By N. Karapinar

Ferrihydrite, a member of iron oxides family, has been used as an adsorbent for the removal of heavy metal ions from industrial wastewater. The success of the operation depends mainly on the efficient removal of ferrihydrite from the aqueous phase. Hence, the emphasis of this study was given on the separation of ferrihydrite by high gradient magnetic separation (HGMS) method to overcome solid-liquid separation difficulties of ferrihydrite. Magnetic seeding technique in which the magnetite mineral was chosen as a seeding reagent was used to make magnetic separation available. The method clearly involves the attachment of ferrihydrite to a magnetic seed material and subsequent magnetic separation of ferrihydrite ? magnetite coagulates. Seeding of ferrihydrite with magnetic particles was achieved by exceeding the solubility limit of the ions in the presence of dispersed magnetite. Magnetic separation results of seeded ferrihydrite showed that maximum seeding performance is obtained in the pH range of 7.0~10.0. Iron/magnetite ratio had a marked effect on the separation of seeded iron oxide precipitate by HGMS. This ratio determines the operation parameters such as magnetic field strength and flow rate. It was concluded that when used with magnetic seeding technique, HGMS can be used to surpass separation difficulties of ferrihydrite used in adsorption-based treatment techniques.

Jan 1, 2014

By Chi Zhang, Junyi Wu

"With the increasing popularity of lithium cobalt oxide in lithium ion battery industry, which is driven by new energy vehicle and mobile device applications, the demand of cobalt is also growing rapidly in recent years. There is a significant trend of increasing investment on cobalt capacity in China, and the automation renovation is considered as an option of improving production efficiency. This study aimed at evaluating the practicability of stainless permanent cathode blank and automatic stripping process in cobalt electrowinning process. The purpose is to replace the old starter sheet process in cobalt electrowinning, which so far was used by most of cobalt refineries in China, but very labor intensive and exposed operators to serious aerosols that contained both cobalt and acid. In the old starter sheet process, the initial cobalt starter sheet is produced onto a plate made of titanium, while the titanium cathode blank and hanger bar fit the critical corrosive environment but is lack of mechanical strength for automatic production which has been mature in copper electrowinning process. To evaluate the proper materials instead of titanium, the coupon corrosion tests with different raw materials including 316L and other stainless steel grades were held for several months in production environment at a cobalt tank house in China. Following the comparison between titanium and other tested materials, a pilot production test in a cobalt tank house is also on-going.INTRODUCTION Cobalt has been known in early China and used in pottery glazes, and the ancient Greeks and Romans used its compounds to make colored glass since long time ago. The blue on the colored porcelain from the Tang Dynasty in China was also due to the presence of cobalt compounds. The word cobalt is known being derived from the German kobalt, from kobold meaning ""goblin"", because the cobalt-bearing blue ore, CoAsS, was called kobaltin in Europe in the Middle Ages, it may have been thought to be harmful to the health of the miners because of arsenic in the ores."

Jan 1, 2018

By D. Jamróz, A. Surowiak, T. Niedoba, P. Pieta

"The separation of coal material of three types of coals originating from three various Polish hard coal mines (types 31, 34.2 and 35, according to Polish nomenclature, which were steam coal, semi-coking coal and coking coal) into particle size fractions and then into particle density fractions was done and then the following parameters were measured for each particle size-density fraction: combustion heat, ash contents, sulfur contents, volatile parts contents, analytic moisture. In this way a 7-dimensional vector of data was created. Using methods of factor analysis the important features of coal were selected, which decide about their membership to individual types. To evaluate the appropriateness of the applied method the Bartlett’s sphericity test as well coefficient of Kaiser-Mayer-Olkin (KMO) were used. To select important factors the Kaiser criterion and Cattell’s scree test were used. The obtained results were compared with the results obtained in previous works by means of observation tunnels method. The results showed which particular features are crucial to define the type of coal what is also important to select appropriate method of its enrichment.INTRODUCTION Coal extracted from the mine is often a mixture of coals of various quality originating, for example, from various coal layers. One of the most important issues is to determine its quality, what means to verify if it fulfills certain requirements. Usually, such parameters as combustion heat, ash contents, sulfur contents, volatile parts contents and analytic moisture decide what the coal quality is (Drzymala, 2009). Such investigations are expensive and time consuming. That is why it seems to be important to determine the mutual connections and interactions between them what would make possible to reduce the amount of the necessary parameters. This issue was already investigated with successes in several works [Jamróz and Niedoba, 2013; 2014; Niedoba, 2015]. This work is another approach to this problem. Here, the investigation of possible reduction of researched parameters was done on the basis of the factor analysis. The obtained results confirm the earlier observations."

Jan 1, 2018

By P. Braga, A. Chaves, S. França, A. Luz

"In Brazil, there are no official reserves of molybdenum, and the unofficial reserves are modest. Therefore, the molybdenum ore (molybdenite) produced as a co-product or by-product of emerald mining in the region of Campo Formoso, BA, has arisen as the only economic option. The flotation process is commonly used in Brazil for the recovery of molybdenite from emerald mining tailings, but it produces low-content molybdenite concentrates, thereby resulting in a product with low economic value. The molybdenite concentrate produced in Campo Formoso contains 83.5% MoS2 (50% Mo), which is less than the international standard product that contains > 90% MoS2 (54% Mo).This low value is due to the presence of talc, which is a naturally hydrophobic mineral that is also floated with the molybdenite during the flotation process. Separability studies were done in a Partridge-Smith cell using dextrin and quebracho as a molybdenite depressor in solution at different concentrations and pH values to produce a technical-grade concentrate (i.e., 90% MoS2). These basic studies were accompanied by measurements of the zeta potential and contact angle, which was determined by the capillary rise method. The results of these floatability studies were used in bench flotation tests, which were performed in a Denver laboratory flotation cell. A molybdenite concentrate of 93.4% MoS2 was obtained when dextrin was used at a concentration of 100 g/t."

Jan 1, 2014

By John A. Herbst, Ming Song, Xiangjun Qiu

It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. The study described here shows that these new tools can allow the design of wear part profiles which will maximize mill productivity over the entire life of a liner/lifter system.

Jan 1, 2003

By Larry A. Cramer

"Three primary drivers are setting the trend for base and precious metal processing . they are: continued low real base metal prices, environmental concerns, and continued high prices for PGM.s. Low base metal prices are increasing the search for economies of scale and company consolidation as well as the development of some hydrometallurgical technologies. Environmental concerns are pushing for continued reductions in SO2 emissions and hydrometallurgical technologies. The high prices for PGM.s are driving major expansions and a focus on minerals processing recoveries and, to a lesser extent, reductions in the refining metal lockup.In nickel, HPAL operations on laterites have failed economically but Inco is still pursuing some alternatives. BHP-Billiton and others are developing bioleaching alternatives for nickel laterites and sulphides.Copper continues to be dominated by the hydrometallurgical and pyrometallurgical debate; new hydrometallurgical developments are being tested at several sites whilst the pyrometallurgists continue to make competitive cost and environmental improvements.Gold processing developments are dominated by the use of improved gravity recovery equipment and by the development of thiosulphate as a more environmentally acceptable lixiviant.PGM processing trends are the use of fine grinding technologies, higher power input flotation cells, and new pyrometallurgical technologies. Hydrometallurgical options for some applications are being sought.OVERVIEW The metals industry has remained under price pressure for some time; low and decreasing real prices for most metals have become an expected scenario. Occasional price spikes give some relief but invariably bring expansions and new entrants into an already oversupplied commodity market, thus leading to the continued price pressure. Technical innovation, economies of scale, and improved work systems are continually sought, so as to improve the competitive position of each individual company in such a climate; however, these developments add to the downward price pressure. In such a situation the application of scarce funds to research and development is a difficult task. Excess funding is not available in tight economic times and yet the main route to higher profits is clearly the application of technical developments to lower the cost of producing a metal commodity. Many technical centers have closed as a cost saving exercise and some have coalesced to obtain economies of scale. The Australian based AMIRA research organisation has grown to serve the R&D part of the market well in Australia and in South Africa by acting as the catalyst to form research partnerships between a number of industry players and as an administrator to direct the funding of research projects towards the various applicable research institutions. AMIRA has developed closer ties to Camiro (Canadian Mining Research Organisation) through the appointment of Camiro.s metallurgical processing research director as AMIRA.s North American based director. AMIRA is continuing discussions with MIRO (Minerals Industry Research Organisation) in regard to a merger, with a report outlining the merger proposal expected in March of 2003. Company focused research centers continue to be effective at Anglo American Research Labs, Teck-Cominco Research, Falconbridge Research center, Inco Research and some others."

Jan 1, 2003

By P. V. Malyarov

"This paper examines the grinding and wear processes in drum mills. A summary of the industry’s long-term experience with the proposed linings is presented. A method is proposed for assessing the efficiency of the grinding energy distribution between the successive stages. A case study is presented of grinding energy redistribution at Talnakh Concentrator by replacing spiral classifiers with a drum-type hydraulic screen. The problems of the kinetics of grinding processes in ball mills and semi-autogenous (SAG) mills are examined. It is demonstrated that in ball mills the feed particles are disintegrated by triaxial compression in the mill zones where discrete slippage of the charge occurs at major force interactions between the layers. Mechanism underlying increases in the specific energy consumption in grinding circuits based on SAG mills is shown.The problem of improving the throughput and reducing the specific energy consumption in mineral feed grinding is highly relevant because of the significant energy intensity. Up to 80% of the consumed energy is used to disintegrate ore fed into the drum mill. At all development stages of the drum mill grinding theory, the researchers have paid a great deal of attention to studying the patterns of the charge motion and the kinetics of the feed particles disintegration processes. In [1], it was shown that, due to the slippage between the charge layers being lifted, drum mills at concentrator plants operate in a mixed cascade and waterfall mode. A feature of the mixed mode is the toe zone, where the charge contacts the lining and the transition to a circular path takes place. Studies of the charge motion in the toe zone made it possible to develop a method for designing cross-sectional profiles of lining plates [2] for ball mill drums. The method is based on the principle of interaction between the balls and the lining, where the non-working rear surfaces follow the relative motion path of the balls before impacting the lining, while the working surfaces are orthogonal to the rear ones. Lining with the proposed profile provides contact with the charge and slippage-free transition to a circular path. This ensures an longer service life of the lining, a reduction in specific energy consumption, and an increase in the mill’s feed rate. The proposed method is applicable when designing lining plates of various materials. Steel liners with the proposed profile have been successfully operated [3] for more than 40 years at a number of projects in the industry."

Jan 1, 2018

By Carlos Gualdron, Elizabeth Gomez, Rafael Bolivar

The productivity index of the Coopracarcegua Ltda., a mid-size coal mining company of Norte de Santander, Colombia, was related absenteeism using accident, productivity and profit data four years. The analysis was based on type, severity and frequency of accidents, number of absentee days; price per metric ton, and other relevant parameters. The enterprise is formed by 5 different mines of thermic coal, each one with different exploitation technologies and different productivity. Each mine was analysed separately and the loss of profit due to absenteeism was calculate for each one. The study showed that the foregone earnings due to absenteeism in terms of the whole productivity of the enterprise was about of 6.6% of the total profit average the 4 years, with calculated values of 14.7%, 3.5%, 8.4% and 4% per year in the evaluated period. The study identified that the most important cause of absenteeism was "General Disease". The foregone earnings in 2009, the highest loss for the analysed period, was about US$ 0.937 million and during the whole evaluated period was US$ 2.46 million.

Jan 1, 2014

By N. S. Voiloshnikova

Large-scale continuous ?Resin-In-Pulp? process tests were conducted at Irgiredmet. The object for testing was the sample of oxidized gold ore from one of Siberian deposit. Weak-base ion ex-change resin PuroGold was used as adsorbent. The duration of ?Resin-In-Pulp? tests was sufficient for a completing of three cycles ?Adsorption/Elution?. Gold in feed was 0.95 mg/L. Gold in solid phase of adsorption tails? 0.065 g/t. Gold in liquid phase of adsorption tails? 0.026 mg/L. Total gold in adsorption tails ?0.11 g/t. Gold recovery ?94.3 %. The use of regenerated resin had practically no effect on gold losses with adsorption tails. Alkaline cyanide solution (NaCN-20g/L, NaOH- 5g/L) was used as eluent for gold elution from loaded resin. Elution temperature ?60 °C. Number of eluent bed volumes passed ?10. Loaded resin analysis was following (g/ton): Au? 1700~1250; Ag? 400~460; Cu? 250~450; Zn? 5100~9600; Fe? 860~1200. Elution efficiency: Au? 95.3%~97.8%; Ag? 84.0%~88.0%; Cu? 84.0%~88.0%; Zn? 97.0%~99.0%. Although high zinc resin loading was shown zinc was eluted efficiently. The adsorption properties of fresh PuroGold resin, PuroGold resin after 3 cycle ?Adsorp-tion-Elution?cycles in comparison with AM-2B resin were tested. It was shown from adsorption isotherms that selectivity of PuroGold resin slightly less in comparison with AM-2B resin mainly due to its higher zinc adsorption properties. It was founded on base of test results that adsorption properties of PuroGold resin was practically constant during three ?Adsorption/Elution? cycles. Gold may be efficiently recovered by resin tested. There were no difficulties during gold elution from loaded resin and its regeneration. PuroGold resin was recommended for industrial use in RIP process. Process design criteria were developed and plant design is on progress at the moment.

Jan 1, 2014

By B. McFadzean

Thiol collector mixtures are commonly used in the flotation of base metal sulfides and platinum-bearing ores. There are synergistic benefits claimed for these collector mixtures, with mixtures lowering total dosage requirements, improving coarse particle recovery and the rate of flotation. Some of the secondary collectors are known to have frothing effects. Therefore, a previous study aimed to decouple froth and pulp effects and considered only the bubble-particle attachments in the pulp. This was achieved through microflotation experiments, where various ratios of the ethyl and isobutyl chain lengths of xanthates, dithiocarbamates and dithiophosphates were used as collectors. Results from these experiments showed a marked increase in galena recovery using mixtures of xanthate with either dithiophosphate or dithiocarbamate. In the current study, the froth phase was introduced in the form of batch flotation studies to determine whether benefits noted during microflotation experiments would be carried through to a more realistic froth flotation scenario. The findings show that there was no significant difference in the flotation recovery between the best single collectors and mixtures of these collectors. In addition, single collectors that behaved poorly in microflotation experiments showed good flotation performance in the batch flotation experiments. The differences between the microflotation results and the batch flotation results are attributed to differences in particle froth stabilizing properties and/or differences in energy input between the microflotation and batch flotation cells. In addition, galena and pyrite showed marked differences in frothing effects and in their preferences for collector type. Keywords: froth flotation, collector mixtures, sulphide minerals

Sep 1, 2012

By P. M. Solozhenkin, V. N. Kovalev

Russia is a global antimony market leader. The three major antimony production provinces are Sakha Republic (Yakutia), Krasnoyarsk Territory and Trans-Baikal Territory. Russia’s largest antimony resources are Zhipkozhinsky and Solonechensky deposits in Sakha Republic (Yakutia) and Olimpiadinskoe deposit in Krasnoyarsk Territory. This work demonstrates the efficiency of computer programs and chemical technology aimed at the study of the behavior of collectors used in the processes of flotation of antimony, arsenic and Au (I – III) minerals. The most promising collectors for the flotation of ores containing antimony and gold on the basis of P(V) and compounds with S, O and N atoms were chosen. The mechanisms of interaction with the mixtures of two or three components of collectors were studied. High recovery of antimony and gold was reached in the processing of Au-Sb ores of Sarulah and Sentachan deposits in Sakha (Yakutia). X-ray radiometric methods of separation of antimony ores of Trans-Baikal Territory deposits were proposed. In order to choose the most cost-effective solvents for hydrometallurgical processing of Sb, Au-containing concentrates the method based on clusters formation between transition solvents and antimony minerals was suggested. The nature of Au losses was theoretically revealed in the sulfide-alkaline process. On the base of computer simulation, the formation of various complexes of (KAu) types was developed, for example, hydrosulphidic gold, thiosulfates of gold - Na3AuS4O6, antimony and arsenic gold, trithiostibate (III) and trythioarsenate (III) KAu were produced. The practice of processing of goldantimony concentrates to produce high-quality antimony trioxide and antimony-gold containing alloy (AGCA) regarding the special conditions of the Far North region, were analyzed. The affinage of AGCA was recommended. Creative project development of antimony industry in Russia in order to produce antimony compounds and pigments, including pyriform compounds and flame retardants (antipyrenes) is discussed.

Jan 1, 2018

By Ljubisa Obradovic, Baisui Han, Batnasan Altansukh, Zoran Stevanovic, Atsushi Shibayama, Jonovic Radojka, Daizo Ishiyama, Kazutoshi Hag, Radmila Markovic, Ljiljana Avramovic

This paper discussed a combined froth flotation and high pressure leaching (HPL) process to recover copper from mine tailings. At first, froth flotation were carried out using the mine tailings sample under various conditions in the presence of different pH (3.5-10) and sulfurizing reagent value (0-1000 g/t), respectively. As a result, optimum condition (sulfurizing reagent of 1000 g/t, pH of 10, PAX (collector) of 100 g/t and MIBC (frother) of 200 g/t) was found for froth flotation of copper. The effects of sulphuric acid concentration, leaching temperature, total pressure (steam pressure plus oxygen pressure) on high pressure leaching (HPL) of mine tailing were investigated using sulphuric acid solution in the presence of oxygen. The best conditions for HPL were obtained to be sulphuric acid concentration: 0 mol/L (water), leaching temperature: 170 ?, total pressure: 2 MPa, leaching time: 1 hr and pulp density: 100 g/L. The leaching rate of copper reached nearly 99 % and the concentration of copper in pregnant leach solution (PLS) was 0.24 g/L. Finally, copper in the mine tailing was recovered using froth flotation followed by HPL. As a result of a combined froth flotation and HPL, the vast majority of copper (99 %) from the mine tailings was extracted.

Jan 1, 2014