Search Documents

By Francesco Vegliò, Luigi Toro, Francesca Pagnanelli

Different hydro-metallurgical processes have been studied in order to recover manganese(II) from oxidised minerals such as MnO2. An innovative acid reductive leaching carried out in mild experimental conditions was here considered using agricultural and industrial wastes containing carbohydrates as reducing agents. The leaching process was investigated from a kinetic and equilibrium point of view in order to optimise the experimental conditions, develop a kinetic model and obtain high purity concentrated MnSO4 solutions. To study the leaching kinetic a Shrinking Core Model (SCM) was modified by a variable activation energy term to take into account both the variable reagent concentrations and the reaction rate change with respect to the manganese dioxide conversion. The influence of the particle size in the kinetic model is discussed with the support of SEM analysis before and after leaching. Manganese extraction yield was maximised (170-190 g/L) using appropriate carbohydrates and acid excesses, while impurity concentrations were kept low (Fe<10ppm and Ca<300ppm) pre-treating the ores, using hydro-alcoholic leaching medium and different combinations of down-stream processes. In particular precipitation, solvent extraction and adsorption onto active carbon were tested to eliminate Fe and Ca from MnSO4 solutions.

Jan 1, 2003

By D. Steele, B. Ndlovu

"Adequate characterisation of clays is becoming increasingly important as operating mines move into areas of more complex ores. The processing therefore needs better mineralogical characterisation to identify problematic ores for better planning before issues arise. While a number of instrumental mineral characterisation methods are available, X-ray Diffraction (XRD) is widely recognised as perhaps the best technique for the identification and quantification of minerals, particularly clays. When an appropriate sequential and systematic sample preparation and treatment protocol is employed with instrumental XRD analysis individual clays can be uniquely identified, and the proportions of interstratified clays can also be quantified. The effect of sample preparation on the XRD analysis and identification of clays was investigated in this study. The results showed that sample preparation protocol is indeed critical to accurately analysis and characterisation of clays. For example, both dry grinding and micronizing affected the degree of crystallinity of kaolinite leading to the formation of reactive surfaces or changes in the physicochemical behavior. It was also found that the apparent degree of preferred orientation in platy minerals correlates directly with the amount of force/pressure applied during the preparation of backfilled powder samples. This work showed that manual preparation can produce highly variable peak intensities especially with minerals that show any preferred orientation. KEYWORDS Clay; XRD; kaolinite INTRODUCTION Clays are important in our life and they have numerous applications in modern world from cosmetics to environmental remediation. Therefore, clays have been extensively investigated for many years. Adequate characterisation of clays is becoming increasingly important as the mineral processing industry faces more complex mineralogy with the need for better mineralogical characterisation to identify problematic ores and plan accordingly. In most studies, X-ray diffraction (XRD) method has shown the unique capability to characterise mineralogy, especially for the fine grained size materials. The XRD technique is particularly diagnostic for clays. It is known that under ideal conditions, the peak intensities of an XRD diffractogram are proportional to the concentrations of individual minerals present in the sample. Hence, the qualitative mineralogical data obtained from XRD can be quantified, using either the internal or external standard methods. However, it is also known that clays are particularly sensitive to the influences of sample preparation method due to their physical characteristics (e.g. fine grain size, morphology, relative physical softness, crystallinity, thermal sensitivity) that could be destroyed by inappropriate preparation prior to the analysis. Thermal and mechanical treatment and grinding of clays can change their crystalline structure, and consequently, their characterisation results by XRD analysis. The behaviour of clays in grinding has been widely studied, especially for kaolinite (Miller and Oulton, 1970, Milocevic et al., 1992, Tomasevic-Canovic et al., 1992). With prolonged grinding time, the crystallinity of the clays can decrease (Filipovic-Petrovic et al., 2002). It has been shown that grinding may gradually cause the loss of hydroxyl ions of kaolinite (Gonzalez Garcia et al., 1991)."

Jan 1, 2018

By Kr. J. Dedelyanova

Selective flocculation of iron minerals could improve the economics of high intensity magnetic separation as concomitant process. When the minerals are finely disseminated is necessary a finer grinding to be applied which generates a lot of slimes. The HIMS is not enough efficient for particles below 20 microns ? territory where the selective flocculation is already well known industrial practice, so the combination of these two methods of beneficiation can bring a higher grade at high recovery to be achieved. The dynamics and selectivity of the precipitation process is studied in batch tests with flocculant starch and dispersants sodium silicate and sodium hexametaphosphate. The influence of preliminary conditioning with nitrogen acid at pH 2 before flocculation is also investigated. Flowsheet including these two methods is tested and the distribution of iron is shown.

Jan 1, 2014

By Paulo Sérgio de Oliveira, Joaquim D. Donda, Andreia C. Rosa

"The search for energy efficient technologies for comminution processes is constant in mineral processing studies, since those processes represent a major percentage of operational costs. In this context the use of stirred mills is increasing, especially for ultrafine grinding. Although many authors claim that these new equipment are more efficient than the conventional ball mills, there were very little chances to prove that in a practical way, since there are few industrial circuits where those technologies perform the same duty. Therefore, the regrinding circuit of Germano second concentrator offers an interesting opportunity: a vertical mill operating in parallel with two ball mills. During almost two years of operation, several sampling campaigns were conducted to evaluate the vertical mill performance and to compare the operational data of the three mills. The industrial data was also compared to jar mill tests results, which are monthly conducted in Samarco labs in order to predict the specific energy consumption required by the ore fed to these circuits. The vertical mill demonstrated the same ability to achieve the product specifications of the ball mills while proved to be able to reduce the medium specific energy consumption in about 40%."

Jan 1, 2014

By C. Dorfling, S. Bradshaw, J. Eksteen, M. Khesa, C. A. Snyders

Titaniferous ores serve as a major feedstock for the production of a white titanium dioxide pigment, a titanium metal and several other titanium-based products. Such ores exist mainly as heavy mineral sands. Ilmenite is upgraded to intermediate products namely synthetic rutile and titania slag through the synthetic rutile route and the reductive smelting route respectively. Tronox KwaZulu Natal Sands (Pty) Ltd recovers high titania slag via the reductive smelting process while slag is used as a feedstock to the pigment industry and furnace dust from the gas cleaning plant is disposed as waste. Previous investigations have shown that such furnace dust can contain significant amount of titanium-bearing minerals. This study looks at the characteristics of the furnace dust obtained from Tronox KwaZulu Natal Sands and investigates a possible high temperature recovery route in detail. The furnace dust was examined by using x-ray fluorescence, x-ray diffraction, microscopy and laser-diffraction size analyses. The characterization work showed that the furnace dust was rich in titanium and iron, containing 49.4 wt% ??????2 and 29.5 wt% ????2??3. These oxides were associated with Si, Mn, K, and Al oxides as impurities. A Carbolite® vertical tube furnace was used to investigate the extent of formation of titania slag and metallic iron on a laboratory scale at 1500°C, 1600°C and 1650°C. The laboratory reduction tests revealed that the slag samples with an equivalent titanium dioxide content ranging from 70.9 -76.9 wt% at 1600°C and 1650°C could be obtained. The Fe content of the metallic iron samples produced ranged between 93.0 and 97.1 wt%. The experimental results were found to be in relatively good agreement with the FactSage simulations, both of which demonstrated the potential of producing a titania slag and a metallic iron from the furnace dust.

Jan 1, 2018

By E. Lee

Cone crushers are widely used within the mining and aggregate industries for the size reduction of minerals, ores, and rock materials. In mining applications for example, the product from cone crushers is often fed to HPGRs or directly to mills in the subsequent grinding circuit. An improved cone crusher performance can therefore result in an overall improved and more efficient comminution process. The objective of this paper is to systematically study a number of different ways of applying compressive crushing. By mathematically modelling these different crushing concepts and then theoretically optimizing crushing sequences accordingly, each concept can be studied and evaluated. In addition, aspects concerning whether or not the results are mechanically or practically achievable are considered. This study thus explores the advantages and disadvantages of different crushing concepts. In this paper, four different theoretical crushing concepts are presented and studied. The results show that in terms of interparticle crushing, optimal crushing sequences with varying compression ratios can be replaced by easier implemented series of constant compressions without significant deterioration. It is also shown that that considerably better performance is obtained for crushing sequences with both breakage modes. The subsequent comparison between such concepts indicates that different approaches can achieve the same results, and that the different concepts are comparable. It is further concluded that interparticle crushing should be kept to a minimum if fines generation or energy consumption is to be minimized, and that each of the studied concepts presents different challenges for implementation. Keywords: compressive crushing, cone crusher, optimization, modeling, crushing concept

Sep 1, 2012

By L. A. Vaisberg, E. V. Shishkin, S. V. Kazakov

"This research is targeted at finding solution to the problem of reduction of specific energy consumption during disintegration of solid materials with the help of machines, operating in a quasiresonant mode. The objective of the research is the development of an energy-saving method of disintegration of supestrong rock and by-products on the basis of vibrational units with two movable crushing elements, operating in a rigorous synchronous-antiphase mode without stringent kinematic links. In the course of investigations a mathematical analysis of the dynamics of vibrational units was performed to determine required mechanical parameters, allowing for adjustment of the machine actuating elements to high-frequency synchronous-antiphase oscillations in the quasiresonant frequency range. As a result of performed pilot tests, the reliability of desktop studies was confirmed and the dependency of process parameters on the machine regulated parameters in the quasiresonant frequency range was identified. The analysis of obtained data showed that during machine operation with cone-shaped crushing elements in the quasiresonant frequency range, the yield of the high-quality finished product (WFA grits of -3+1 mm grain size class) in one pass reaches 35%, whereas the form of the particles corresponds to the grain form with sharp edge. The quasiresonant operation mode of the vibrational unit with two freely suspended crushing elements (without stringent kinematic links) provided substantial reduction of energy intensity during crushing down to 0.16 kWh/t, which shows reduction of power consumption for crushing by more than 15% compared to conventional equipment.INTRODUCTION The most common and energy-consuming processes in the mining industry are the crushing and grinding of various solid materials. Such large energy costs are due to the fact that the capabilities of the existing crushing and grinding machines are based on traditional methods of destruction, and are limited by their kinematic features, which do not allow to reduce the energy intensity of processes, to lower the irreversible loss of useful components, to improve the quality of marketable products. In connection with the foregoing, the task of energy costs reducing for disintegration is one of the most important issues in the enrichment of both minerals and processing of man-made raw materials. The solution of this problem is possible only through the creation of a fundamentally new highly efficient technique and technology for processing raw materials [1, 2]. It seems that the greatest prospects in this respect are the vibration methods of disintegration, in particular, the vibratory cone crusher based on a two-mass system without rigid kinematic connections between the crushing bodies, with vertical vibrations of the working bodies. In this machine, the principle of rational material destruction is realized – crushing without re-grinding [3-5]."

Jan 1, 2018

By Robinson Irarrazabal, Edison Collinao, Rodrigo de Carvalho, Patricio Davila, Marcelo Tavares

"In recent years, DEM (discrete element method) softwares, along with 3D laser measuring equipment, have become powerful tools to describe mill charge behavior, as well as forces acting on the liners of SAG mills. With the aim of contributing to streamline this application of the advanced technologies ME Elecmetal and Universidade Federal do Rio de Janeiro, UFRJ, proposed a new approach to improve the design of mill liners using elements from mechanistic modeling of grinding. The paper presents a methodology for continuous improvement of liner design, which uses information from the DEM collision energy spectra in the mill discriminated for the different components (ore and steel balls), as well as information on the breakage properties of the ore being ground. From these it proposes the concept of "effective collisions", which corresponds to the collisions that are of sufficient magnitude to cause breakage, thus allowing to discriminate from impacts that do not cause breakage either in a first impact or after repeated loading. It also tracks the collision of steel balls against the shell in order to assess their potential damage to the liners. An industrial case study is presented of a 38’ diameter SAG mill, which was experiencing challenges associated to liner breakage and low efficiency with the old liner design. Through a modification of the liner design, simulations demonstrated the potential benefit associated to reduction in ultraprojection and improvement in mill capacity. Implementation of the new design in the SAG mill was carried out, resulting in increase in daily throughput from 6 to 12%. Further, the time spent in liner change was reduced by 47% given the reduction in the numbers of parts. This operation also benefited from having no stops due to unplanned shutdowns to replace broken tiles. These demonstrate the benefit of coupling advanced computational tools to sound engineering principles in continuous improvement of liners."

Jan 1, 2014

By T. B. M. Himawan

In this study, effect of thiosulphate and oxidation using oxygen were studied in arseno copper ore flotation. Single mineral study of chalcopyrite and tennantite in regard to the aforementioned techniques was also studied. Zeta potential, XPS, contact angle and floatability of single minerals were conducted for each treatment to understand the mechanism. It was revealed that the separation is best conducted in alkaline condition at where there will be interaction between thiosulphate and the mineral surface as well as the formation of hydroxide species in the oxidation using oxygen. From zeta potential of both thiosulphate and oxidation conditioning, it can be found that the reactivity of tennantite is much higher rather than chalcopyrite resulting higher rate of depression on both techniques as shown from contact angle and floatability of each mineral after treatment. XPS spectra confirmed qualitatively and quantitatively the existence of species responsible for the depression of each conditioning techniques. As for the copper ore flotation test, it is the oxidation using oxygen provides best performance after 60 minutes of oxidation. Keywords: tennantite, chalcopyrite, arseno copper ore A, thiosulphate, oxidation using oxygen

Sep 1, 2012

By T. Sreenivas

This paper describes results of laboratory studies on recovery of dissolved uranium values from alkaline leach slurries of a medium-grade uranium ore from Gogi (Karnataka, India) using the resin-in-pulp (RIP) process. Besides anionic carbonate complex of uranium, the other major ionic constituents of the leach solution are CO32-, HCO3-, SO42- and MoO42-. The total dissolved solutes (TDS) are about 45 g/L. Various commercially available strong bases anionic resin-in-pulp (RIP) grade resins ? both macroporous and gel type, were studied with respect to their loading capacity. Parametric variation studies were then carried out with the short-listed resins. Results of the semi-continuous counter-current extraction and elution tests indicated extraction efficiency of about 98% and practically complete elution of the loaded uranium values with NaCl eluant using a gel type polystyrene based resin grafted with quaternary ammonium ion. Keywords: uranium, hydrometallurgy, ion exchange, resin-in-pulp

Sep 1, 2012

By G. Dodbiba, T. Fujita, M. Kawata, S. Yamasaki, K. Mitsuhashi, J. Ponou, Y. Iwazaki, T. Atarashi

"The grade of copper ore and concentrate is recently decreasing and it will continues decrease further in the future. The effective liberation treatment for low grade copper ore and the removal of arsenic from copper concentrate is becoming even more important. In this work, the magnetic separation of copper concentrate by heat treatment and the flotation of low grade copper ore by microwave irradiation was studied. The heat treatment of copper minerals in the air atmosphere, the magnetization of most copper minerals increases and especially the magnetization of chalcopyrite shows the largest magnetization, after being heated at 500 oC. The wet HGMS of copper concentrate has been studied and the results have then been compared with the ones when calcined concentrate was used instead. The microwave treatment before ball milling increased the degree of liberation up to 100%, especially when compared with the case when only ball mill was applied to the as-received ore. The flotation of ground copper ore after microwave irradiation showed that the grade copper minerals such as chalcosite and bornite in froth part is much larger than that of tailing part.INTRODUCTION The copper has been used many kind of technological fields and will be more important for the future technology. The global copper production from mine is predicted as shown in Figure 1 (Northey, S. 2014). The copper production peak will be appeared in 2030 and the demand peaks in 2040. In the future the recycling of stocked copper and copper alloy will be necessary to satisfy the demand (Yoshimura, A. 2018). Changes in the grade of copper in copper concentrate, exported from several countries are shown in Figure 2. The copper grade in copper concentrate after mineral processing is gradually decreases every year and it is less than 30% nowadays. On the other hand, the copper ore grade change and prediction are shown in Figure 3. The grade of copper ore is also decreasing to less than 1% in 2010 (Northey, S. 2014). In the future the copper grade gradually decreases, reaching to less than 0.5% in 2080 and the energy to produce the copper metal will increase. The effective liberation treatment for low grade copper ore and the removal of arsenic from copper minerals become more important, nowadays. The microwave irradiation of copper ore for the liberation, energy etc. has been reported by several researchers (for example, Batchelor, A.R. 2017). The magnetization change of copper ore by heating has been reported to remove the arsenic (Sawada, M 2015). In this report, the magnetic separation of copper concentrate by heat treatment and the flotation of copper concentrate by microwave irradiation are discussed after the characteristics of secondary copper minerals are investigated by these treatments."

Jan 1, 2018

By Brian Hart, Liuyin Xia, Staman Dimov

The recovery of rare earth elements (REE) is fast becoming of significant interest globally. Modern research and development programs (outside China) towards the optimization of REE mineral recovery by flotation have been lacking. Due to the mineralogical nature of many hosting deposits, the separation and recovery flotation flowsheets can be very complex. As part of a research project, a selected suite of hydroxamic acid collectors (Naphthoyl, Cyclohexyl, Benzoyl, Octyl, Terta-butyl benzoyl, Salicylic) were tested in order to examine their potential for recovery and selectivity. Micro flotation tests were conducted on a feed sample, recovery and grade of the products were used to evaluate their relative flotation efficiency and selectivity and these results (flotation with the hydroxamate collectors) were compared to a phosphoric acid/sulphonate collector mix(shorten as "mixed"). In the testing, the flotation response with the hydroxamate collectors was significantly better than the "mixed" collectors on freshly ground (no slimes removed) samples. Furthermore the tests revealed that for most of the hydroxamate reagents tested, their dosage requirements to achieve recoveries at the same levels was less than that for the "mixed" reagents. Product assays show that recovery of both La and Ce is significantly better for using the salicylic hydroxamate and that Nb, Y and Zr recovery are favored by using octyl hydroxamate. These results indicate mineral flotation selectivity could be achieved by using selective hydroxamtes. Spectral fingerprinting by TOF-SIMS surface analysis has allowed for the identification of reagent species. TOF-SIMS surface analyses of grains analysis confirmed that REE bearing grains reporting to the concentrates are doing so in response to collector attachment whereas grains reporting to the tails are doing so in response to a lack of collector. The TOF-SIMS surface data bas been used to examine the factors promoting flotation stream partitioning.

Jan 1, 2014

By David De Klerk, Maximilian Richter, Thirunavukkarasu Pathmathas, Indresan Govender

We consider the average power dissipation distribution for dense granular flows of an idealised mono-sized charge (5 mm glass beads) in a 300 mm diameter tumbling mill operated in the cascading-to-cataracting Froude regime. By combining the inherent frictional nature of particles within a dense flow regime and noting that tumbling mills are typically characterised by collisional and turbulent stresses, we derive the power dissipation distribution for athermal boundary conditions. The input data to the model (velocity, solids concentration, pressure and flow depth) are obtained directly from non-invasive measurement using a nuclear imaging technique: Positron Emission Particle tracking (PEPT). The power dissipation due shear stresses is shown to be the dominant mode of dissipation in the tumbling mill with up to two orders of magnitude difference between pressure induced dissipation and shear.

Jan 1, 2014

By M. Gonzalez Fernandez

"Commercially introduced in 2004, the SAGDesign™ test has today proved its efficiency for sizing SAG mills for a wide variety of ores, from very soft to very hard ones. The interest of building a model using the SAGDesign™ test specific energy is the introduction of such a model into a complete process simulator making it possible to predict a complete material balance. The developed model compares the required specific energy with the energy provided by the mill. This energy calculation is derived from the Austin Power Formula. The specific energy provided by the test is corrected, using various parameters, such as the Ball Mill Work Index, to take into account the true operating conditions, the feed and product sizes. The core of this model allows the determination of the product d80 using the mill geometry, its operating conditions and of course the SAGDesign™ test results. To be included in a simulator, the model must also predict the overall size distribution of the SAG mill discharge. Assumptions to answer this point are presented here. The model has been implemented in the USIM PAC simulator. It is used either to predict the product size distribution for a given SAG mill, but also to size a SAG mill for getting a required reduction ratio. INTRODUCTION Over the last few years several types of new comminution machines have been introduced in the market. The most notable newcomer was the HPGR (Morley, 2006). But, even when these machines have some advantages, they have not earned the trust of the mining industry. That is why the established technologies still being the first choice. And, in comminution, that first choice are SAG and ball mills. The design of ball mills has been well understood for a long time. The Bond Ball Mill Work Index is the standard test which helps to describe the ore in terms of energy requirements for milling. Unfortunately, the development of an equivalent test to characterize the ore subject to SAG milling has taken some time. As of today, several tests are available in the market, like the MacPherson test, the MinnovEX SAG Power Index (SPI™), the JK Drop Weight Test, the SMC Test® and the SAGDesign™ test (Verret et al., 2011). The SAGDesign™ test, developed by John Starkey in Canada in the early 2000s (Starkey et al., 2008, 2015), has become one of the standards to assess the grindability of an ore in a SAG mill. One of its advantages is the reduced sample mass needed to perform it, hence, the reduced cost. The second one is that the output of the test is straightforward, it is the energy required to grind the ore between two sizes. Because of this energetic approach, the results provided by the test can be directly applied to size a new mill or to assess the performance of an existing mill."

Jan 1, 2018

By John A. Herbst, Ming Song, Xiangjun Qiu

"It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation (HFS) tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. An illustration of this analysis is shown in Figure 1 below.Here we see that after a new lining is installed (Region I) the wearing process reduces the liner thickness resulting in a larger power draw and an associated higher throughput until Region II is reached. By this point the lifter height is reduced significantly changing charge motion (less cataracting) the power begins to decline, but the comminution efficiency increases with this type of “calmer” breakage environment therefore the throughput continues to increase. In Region III the lifter is no longer providing the minimum required charge lifting action, the power and the throughput both drop off significantly. In the last two stages the behavior is especially complex because throughput is not linearly related to power since grinding efficiency is changing.The study described here shows that these new HFS tools allow the design of wear part profiles which will maximize mill productivity over the entire life of liner/lifter systems. A simple example of such a design procedure is shown involving the selection of a sinusoidal profile for a 34 ft diameter SAG mill.The paper discusses how the principles exposed in this simple example can be applied to search for an optimal profile in which non-standard modifications are allowed to compensate for throughput or wear shortcomings of standard profiles."

Jan 1, 2003

The ever increasing demand for energy and the progressive depletion of crude oil resources, have renewed interest in oil shale as an alternative fuel resource. Weathered oil shale samples were assembled from El-Nakheil phosphate mine in Quseir area, Eastern desert, Egypt. The oil shale samples were prepared and analyzed by XRD (X-ray diffraction), XRF (X-ray fluorescence spectrometry), and optical microscopic techniques. Rock-Eval pyrolysis and total organic carbon were used to study shale hydrocarbon potential. A leaching procedure using inorganic and organic acids was used to selectively dissolve the oil shale associated ash forming minerals. XRD results showed that calcite is the dominant carbonate mineral, whereas primary silicate minerals are quartz and montmorillonite. SEM (Scanning Electron Microscopy) observations indicated that the organic matter is dispersed throughout the rock matrix. The acid soluble fraction upon leaching was determined to be 37.59 and 42.74 wt% by using 5% HCl and 10% HCl, respectively. The TOC was increased from 20.78 to 29.88 and 34.09 wt% by using 5% HCl and 10% HCl, respectively. Keywords: el nakheil oil shale, characterization, xrd, xrf, sem, elemental analysis, proximate analysis, ultimate analysis, thin section, rock eval pyrolysis, acid leaching

Sep 1, 2012

By John Ralston

"Interfacial chemistry plays a pivotal role in bubble-particle capture, for it controls whether or not attachment occurs. Surface heterogeneity, degree of surface hydrophobicity, bubble nucleation and related phenomena influence the stability of the aqueous wetting film between a particle and an approaching bubble. The latter must be unstable if capture is to occur. Various techniques that may be used to quantify this interfacial, chemistry-dominated behaviour, are described.The efficient capture of specific particles by rising bubbles and the delicate control of interfacial chemistry that leads to selective capture are central issues in froth flotation. For efficient capture to occur between a particle and a bubble, they must undergo a close encounter, a collision process dominated by hydrodynamics. Should this encounter bring the particle and bubble within the range of attractive forces, the intervening liquid film between the bubble and the particle will drain, leading to a critical thickness at which rupture occurs. The liquid-vapour interface then retreats over the solid particle surface until a stable wetting perimeter is established. The particle and bubble are then joined after this attachment process. The particle may only be dislodged from this state if it is supplied with sufficient kinetic energy to exceed the detachment energy in this detachment process. These various events are now well documented and may be followed using high-speed videomicroscopy (Schulze, 1984; Nguyen et al., 2001).The process of collision can now be described quantitatively for single bubbles colliding with bubbles under various flow regimes (Dai et al., 1998) and appropriate scale up is possible for multiple bubble particle collisions occurring under turbulent conditions (Pyke et al., 2002). In this paper we will be concerned with the role of interfacial chemistry and how this influences the attachment process."

Jan 1, 2003

By Qingming Feng, Dongbo An, Jinhong Zhang

The application of the geopolymerization of mine tailings as construction materials is hindered by the fact that conventional geopolymerization of mine tailings usually involves a large consumption of alkali, i.e., sodium hydroxide (NaOH), and a long curing time, because of the relatively low reactivity and the high Si/Al ratio of mine tailings when compared to other active resources such as fly ash and clay minerals. The present study is focused on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. We firstly investigate the temperature effect on the alkali activation of mine tailings during geopolymerization. Secondly, the impact of additives, i.e., calcium hydroxide and aluminium oxide, on the compressive strength of samples is studied. Thirdly, different forming pressures have been applied to remove excessive alkali and its impact on samples&apos; strength has been investigated. The results show that a 40 MPa unconfined compressive strength (UCS) can be achieved with the geopolymerization samples after mine tailings are activated by sodium hydroxide at 170°C for 1 hour with the addition of calcium hydroxide and alkali dissolved aluminium oxide, further compressed with a 10 MPa forming pressure and finally cured at 90°C for 3 days. The findings of the present work provide a novel method for the geopolymerization of mine tailings as construction materials.

Jan 1, 2014

By Rasool Hejazi

The feed to Chadurmalu iron ore concentrator plant is a mixture of magnetite and haematite iron ore with a Fe/FeO ratio of about 8. The feed to plant, after grinding via wet SAG mill, is pre-separated by wet low intensity magnetic separator. Magnetic product is conducted to magnetite processing circuit for producing magnetite concentrate, and nonmagnetic product is directed to haematite processing circuit. Due to surface oxidization of magnetite particles and a decrease in magnetic attraction properties, significant amount of these particles are misled to tailing which results in decreasing the efficiency of haematite processing circuit. This problem can be remedied by using magnetic drum separator with more magnetic intensity and/or gradient. In this paper, the replacement of LIMS separators with wet medium intensity magnetic separators with a field intensity of 3800 gauss on drum surface (MIMS) have been suggested and considered as the most suitable solution to prevent the loss of magnetite particles. The results of carried out investigations with replacement of drum separators in industrial scale, showed that utilizing MIMS in magnetite processing circuit resulted in increasing final concentrate weight recovery on average by 2.59%, without any adverse effect on the concentrate quality; decreasing the magnetite content in the feed to high gradient magnetic separator (HGMS) by about 3.5%; decreasing the feed to floatation part by about 7% and consequently decreasing consumption of chemical reagents; increasing Fe/FeO ratio of the feed to plant. Keywords: iron ore, medium intensity magnetic separator, haematite, Chadurmalu

Sep 1, 2012

By Jiang Wenli, Zhang Yimin

In order to enhance the quality of iron concentrate from magnetic separation, reverse-flotation technology is often applied in an iron ore dressing plant.However, this technology has disadvantages in terms of operating cost,energy consumptionand environmental protection(Zhao, Wu& Wang,2005).Developing innovative equipment to process magnetite ore more-effectively is a way to get rid of these disadvantages of reverse flotation and improve the quality of iron concentrate.This paper describes the development of Complex Flashing-Field Magnetic Cleaner,a new kind of equipment based on the principle of combination of separation in magnetic field and separation in gravity field(Hao & Jiang, 2002).This innovative equipment possesses a tailor-made magnetic system and has the characteristics of a magneticfieldwhich can strengthen the formation of magnetic agglomerations and the dispersion of gangue mineralsto improvethe quality of separation.The automatic control system developed specifically for this equipment can further increase the accuracy of separation and stabilize the process.

Jan 1, 2014