Search Documents

By Yang Zhao, Tao Xiu-xiang, Chen Song-jiang

"China is rich in low-rank coals that account for 45.68% of existing coal reserves in China. The clean and efficient utilization of low rank coals is of great significance for ensuring the effective energy supply and promoting economic development and environmental protection. In order to solve the difficult problem in flotation of low rank coal, it has become the focus of research in the related field that oily bubbles instead of air bubbles are taken as a carrier in flotation to improve the attachment efficiency and recovery of low rank coal. In this paper, low rank coal slime collected from Shendong mining area was used as the experimental material, and it focused on the characteristics of oily-bubble flotation process of low rank coal. Additionally, difference in conventional flotation and oily-bubble flotation was discussed. The induction time between air bubbles, oily-bubbles and fine low rank coal particles was measured. The results indicated that the induction time between oily-bubbles and coal particles was obviously lower than that of air bubbles. By comparing the foam height of air and oily bubbles, it was found that the amount of oily bubbles is less than air bubbles, causing relative low flotation rate of oily-bubble flotation at initial stage. Besides, the maximum foam height and half-life of air bubbles and oily-bubbles were measured respectively. The results showed that the stability of oily-bubbles was higher than that of air bubbles, which is benefit for the enrichment of concentrates. The clean coal water recovery of oily-bubble flotation is lower than that of air bubble flotation, which indicated oily-bubble flotation is lower in water entrainment. INTRODUCTION China is the largest energy consumer in the world, accounting for 23% of global energy consumption in 2016 and 27% of global energy consumption growth. Whereas coal is taken as the major primary energy source and its share of China’s primary energy consumption is 62% in 2016, in which the low rank coals, such as lignite, long-flame coal, weakly caking coal, and non-caking coal, accounted for about 50% of total coal production capacity (China’s energy market in 2016, BP). Moreover, the exploitation and utilization of low rank coals and other coals that are difficult to float have been an important strategy for China’s sustainable development of the coal industry (Liu et al., 2014). However, the combustion of low-quality coals leads to a serious environmental pollution. In addition, the deterioration in geological conditions of coal resources, and the increasing improvement in the mechanization for mining significantly caused the increased amount of fine coal."

Jan 1, 2018

By P. Khattri

At Tata Steel, Coal is washed in gravity and froth flotation circuit at 13-15 mm size and below. Being coal is high in ash (~35%) and difficult washability characteristics (having high (~40 %) NGM at desired ash levels) needs more and timely quality data of ROM for effective optimization and process control. Conventional approach of supplying quality data takes 4-5 hours time. This means during this period, it is assumed that coal is having similar characteristics as of previous set and it is not possible to fine tune during this time which resulted in yield loss. Hence producing clean coal on agreed ash value consistently is a challenging task because of high NGM and variation in input quality. To overcome the problem of collection of representative sample and timely result a new technology was adopted Prompt Gamma Neutron Activation Analysis (PGNAA) technology which is basically an online analyser using Gamma rays as the source to measure the ash content in coal running on a conveyor which gives real time ash analysis. The details of this technological intervention are discussed in details in this paper. Keywords: near gravity material, PGNAA

Sep 1, 2012

By J. Shibata

The behavior in electric field of fine particles present in aqueous solution was measured in order to apply to the classification of fine particles. The sample particles used are spherical polystyrene particles with the average diameter of 0.03 µm, 0.1 µm, 1.0 µm, 4.3 µm and 9.6 µm. Electrophoretic mobility and zeta potential of various particles are measured by an instrument based on the principle of the laser Doppler effect. The influence of temperature, electrolyte concentration on the electro-phoretic mobility was investigated for various polystyrene particles. The electrophoretic mobility increases with increasing pH and temperature of suspensions. The measured electrophoretic mobilities are different from electrolyte concentration and particle size. The electrophoretic retardation effect and relaxation effect are considered to explain the behavior of fine particles in electric field by applying the electro kinetic theory of Wiersema et al. For all particle size, the electrophoretic mobility decreases rapidly in high concentration of KNO3 such as 0.1 mol/dm3due to the compression of electric double layer The forces acting the particles in electric field are considered to be electrical force, friction force and some other forces like relaxation effect and electrophoretic retardation effect which appear in ionic behavior. It is considered that the particle moving velocity depends on the particle size. When the particle size is less than 1µm, the velocity increases with increasing the particle size. On the oth-er hand, the velocity deceases with increasing in particle size, when the particle size is larger than 1µm. This phenomenon is considered to be interesting from the viewpoint of classification for fine particles. We found that the electrophoretic mobility of 1.0µm particles is larger than that of 0.1µm particles, and that it is possible to classify fine particles by using the difference of electrophoretic mobility by many experimental results. The phenomena can be explained by the forces acting the fine particles in the electric field. We can apply the behavior to classification of fine particles.

Jan 1, 2014

By Christian O’Keefe, Alex Van der Spek

"Evaluation of inequalities of the partial sums defining cumulative grade and recovery prove that cumulative grade has an upper bound not dependent on the bank number and cumulative recovery possesses an upper bound proportional to the bank number. This explains one observed characteristic of cumulative grade versus cumulative recovery curves. The existence of such maxima combined with the observed shape of cumulative grade-recovery curves leads us to postulate that these curves can be well described by rectangular hyperbolae. Rectangular hyperbolae are characterized by asymptotes at right angles to each other. It is proven that this property can be used to derive an equation for the cumulative mass flow of the concentrate in terms of the asymptotic values of cumulative grade and cumulative recovery. Fitting hyperbolae to experimental cumulative grade cumulative recovery plant data then results in estimates of the maximum grade, the maximum recovery and a constant which may be taken as a performance coefficient of a row. Normalization of the cumulative grade and the cumulative recovery by their respective maxima gives rise to a graphical representation that can be used to evaluate the operating performance of a row of floatation bank cells. The normalization procedure removes the bias that is introduced by inevitable variation in mass flow of the feed and variation in feed mineralogy or feed particle size distribution. Reduction of the normalized data collapses all cumulative grade-recovery data onto one and the same curve. This removes the differences caused by the variation in row performance. The reduced cumulative grade-recovery data scatters around a common hyperbola. This can be used to gauge the validity of the assumptions made. Normalized cumulative mass pull is determined from the fitted values of the maximum recovery and maximum grade. This may serve as an alternative performance indicator of the floatation row."

Jan 1, 2014

By M. Gonzalez Fernandez

"If the final goal of metallurgy is the extraction of metals from a given ore, everyone knows that this achievement relies on many separation steps involving much more than a biphasic material made of metal and gangue. Nevertheless, still today, most of the design and follow-up of industrial processes only consider metal grades; in best case metal grades per size class. Working with such heterogeneous material, made of several minerals, with different grain size and texture, implies to consider finer ore models to be able to predict the behavior of material and the subsequent operation performances. Analytical tools are now available to provide such relevant and accurate data which are applied in geometallurgy. To achieve a true geometallurgical approach for process design, but also for optimization, accurate process simulation absolutely needs to combine these fine ore models with the corresponding unit operation models. Based on generic, but configurable, criteria of description and a hierarchical approach, the material modelling tool embedded in the USIM PAC process simulator provides the necessary flexibility to describe any type of ore with almost no limit in the level of details and associated physical properties that can be met in the mining industry. The simulation engine and the mathematical models of unit operations are designed to manage such a diversity of material modelling. The paper present various ore models and some of their applications in flowsheet simulation. It proves the interest of this detailed and advanced approach to accurately predict plant performances. INTRODUCTION Process simulation used for process design and optimization requires accurate unit operation modeling. During the last decades, main efforts of the different teams developing software simulators have been dedicated to those models for comminution and physical separations such as flotation or gravity concentration (Kojovic et al., 2012, Soni and Yoon, 2014). In most case, the ore is modelled with a size distribution and metal or mineral grades. A water phase is considered for wet processes. The association of unit operations and such material models generally allows, after some parameters adjustment, to achieve good agreement between experimental and simulated data. The use of the obtained simulator to test alternative configuration of circuits or settings of equipment devices can be accurate enough as far as the ore processed is close to the ore used for simulator adjustment. However, when the ore gets very different grades, coming from different mineral proportions or grain sizes, the simulation results can be of poor accuracy. Because any physical separations such as gravity, magnetic or flotation, do not sort metal and gangue but particles, made of minerals, containing metals, the only way to be accurate enough for allowing extrapolations, is to model particles. The phase model tools embedded in the USIM PAC process simulator gives this possibility. However, as such level of details are not always available for analyses, the tool has been designed with a high level of flexibility, to adapt the model to the available data. In this paper, the principles of this conceptual modelling tool are presented, and some application cases illustrate the material model flexibility and its interest."

Jan 1, 2018

By Samira Rashidi, Robert Dunne, Raj Rajamani

"High Pressure Grinding Rolls (HPGR) are known for more energy saving, better particle weakening and higher tonnage compared to semi-autogenous/ball mill circuits. These machines are scaled up based on the roll diameter. Therefore, studies in lab-scale HPGRs are always preferred because less weight of feed sample is required to run batch tests. The 50-hp laboratory-scale machine at the University of Utah is the first-ever lab-scale machine designed by late Prof Schönert, the inventor of HPGR. This 200x100 mm [DxL] HPGR is equipped with a robust data acquisition system, which enables running steady state tests using a feed sample as small as 6 kg to 12 kg. This paper presents the HPGR grinding study on two different categories of ores, one hard ore and the other soft. A test series has been performed to evaluate the energy consumption and the relation with size reduction on open multi-pass and locked-cycle HPGR circuits. The effect of feed size distribution and operating conditions has been investigated. Locked-cycle tests result in higher reduction ratio and higher rate of fines (100 mesh, 48 mesh and 28 mesh) generation when compared to open multi-pass tests. Data shows that scale-up trend lines stay consistent even when the circuit configuration and operating conditions are varied."

Jan 1, 2014

By Zhu Yangge, Zheng Guibing, Hu Xiaoxing

"Because of the similar crystal structure and surface properties, it is very difficult to realize the efficient separation of magnesite and dolomite by flotation, which is the main reason restricting the utilization of magnesite resources with dolomite symbiotic. To deal with a magnesite resources with high content of calcium impurity in northwest China, a novel decalcification technology by combining flotation with leaching is proposed in this paper. In flotation process, a novel flotation collector with good efficiency and low temperature resistance was developed, and the depression effect of sodium hexametaphosphate was investigated. In leaching process, the leaching rate difference of calcium and magnesium was observed. By industrial test, from the magnesite ore with MgO content of 43.96%,the grade and recovery of obtained concentrate ( calculated by MgO) are 47.28% and 67.68% respectively, at the same time, CaO content decreases from 3.91% to 0.30%, which means that more than 95% of CaO impurity is removed.INTRODUCTIONMagnesite is one of the main raw materials for the production of refractory materials, and it is widely used in metallurgy, chemicals, ceramic, construction and other industries. China is the most important supplier of highquality magnesite resources, accounting for about 60-70% of the world's identified supply of magnesite products is provide by China (Jewell, 2014). In recent years, high-quality magnesite ores can be directly used are going to run out in China, and the utilization of magnesite resources with high impurity content have drawn more attention.The main purpose of purification for magnesite is to remove SiO2 and CaO impurities which affects the strength of the refractory material. Flotation is the commonly used method to remove impurities in magnesite ore. Reverse flotation with cationic collector is usually adopted to remove silicon containing impurities, and a great deal of literature has been reported (Santana A. N. and Peres A. E. C., 2001; Wang and Sun, 2008; Zhu et al, 2014; Wu et al, 2015; Ivan B. et al, 2017). But when the major gangue component is dolomite, it is very difficult to realize the efficient separation due to the similar crystal structure and surface properties between magnesite and dolomite. To solve this problem, researches have studied the surface properties of magnesite and dolomite, such as wettability, electrical property, solubility and solution chemistry (Nermin and Nurgul, 2006; Nermin 2006; Ozbek and Abali, 1999; Lacin et al, 2005; Bayrak et al, 2006; Bakan et al, 2006; Chen G. and Tao D., 2004), but the commonly studied direct flotation using oleic acid as collector is still hard to receive an ideal effect."

Jan 1, 2018

By Stoyan N. Groudev, Ioannis Paspaliaris, Irena I. Spasova, Kostas Komnitsas

"Acid mine drainage waters generated in the uranium deposit Curilo, western Bulgaria, were treated by means of a constructed wetland located in the deposit. The waters had a pH in the range of about 2.5 - 4.1 and contained uranium, radium, some heavy metals (iron, manganese, copper, zinc, cadmium, cobalt, nickel, lead), arsenic and sulphates in concentrations much higher than the relevant permissible levels for waters intended for use in the agriculture and/or industry. The wetland covered an area of about 140 m2 and was characterized by an abundant water and emergent vegetation and a diverse microflora. Typha latifolia, Typha angustifolia and Phragmites australis were the prevalent plant species in the wetland but species of the genera Juncus, Eleocharis, Scirpus, Carex and Poa as well as different algae were also well present.The water treatment was started in July 2001 and until now (August 2002) the wetland effluents were characterized by pollutants concentrations decreased below the relevant permissible levels. The water flow rate through the wetland during this period varied in the range of about 0.2 - 1.0 l/s. The water clean-up markedly depended on the temperature but was efficient even in the cold winter months at air and water temperatures close to 0oC. The removal of pollutants was due to different processes but the microbial dissimilatory sulphate reduction and the sorption of pollutants on organic matter (viable and dead plant and microbial biomass) and clay minerals played the main role. Negative effects of the pollutants on the growth and activity of the indigenous plant and microbial communities were not observed."

Jan 1, 2003

At times the phosphate industry, in Florida, encounters phosphate rock that gives lower than expected P2O5 recovery in the rougher plant section. The drop in recovery is typically 10% and as much as 30% or more. Variations in feed quality from day to day, shift to shift and even from drag-line to drag line, represent a challenge to the beneficiation plant operators and reagents? suppliers. Therefore, this characterization study has been initiated to identify the reasons for the differences in flotation behavior of such feeds. The study involves many samples to cover such variations. The characterization work includes: ? Mineralogical and chemical analysis; ? Size, shape, surface roughness and porosity analysis; ? Surface charge and surface contamination with other phases (minerals); ? Clay content and its relationship to phosphate and silica particles. The results correlated with flotation data and adsorption density measurements clearly establish the statistically significant variability in characteristic features that influence flotation response. This article discusses results from the above listed studies. On the basis of the obtained data, recommendations of practical approaches to overcome the problem of feed variability in phosphate flotation plants are delineated.

Jan 1, 2014

By Nirmal S. Weerasekara, Malcolm S. Powell, Mohsen Yahyaei

"An understanding of the fundamentals of different breakage mechanisms is critical for successfully modelling comminution processes. Due to the high frequency of low energy collisions in the grinding process, superficial breakage has a significant role in size reduction in mills. To develop a scaling up methodology for characterising low energy surface damage behaviour of ores, a series of surface damage tests have been conducted using three grinding mill sizes with diameters of 1.8, 1.2, and 0.8 m. Two types of gold-copper ore with different hardness were used: C-ore and T-ore. All tests were conducted using wet mode to remove the products during grinding. To ensure low energy surface damage was the dominant mechanism, in all tests the mill speed was reduced to 40% of critical speed. A surface damage index normalised with product mass and surface based specific energy is determined from the results enabling a study of the grinding performance regardless of mill size, energy level or charge mass. Incremental breakage tests using the JKRBT indicate that the A×b values of the T-ore were 60% higher than C-ore, suggesting the T-ore is considerably softer. The fractional mass loss rate for the T-ore in the 0.8 m and 1.8 m mills started from 16 and 7 (1/kWh/m2) while for the C-ore it was 4 and 2 (1/kWh/m2). After 6 minutes the surface damage index in all tests tends towards steady state a constant value, an indication of steady state surface damage condition. It has been demonstrated that this methodology can be a useful basis for characterising superficial breakage behaviour of ores."

Jan 1, 2014

By D. Kosior

Influence of frothers (a-terpineol and n-octanol) concentration on kinetics of a three phase contact (TPC) formation by a bubble colliding with a hydrophobic surface (Teflon) of different roughness was studied using a high-speed camera (1040 frames per second). It was found that the Teflon surface roughness and the frother concentration strongly affected time of the TPC formation (tTPC) and time of drainage (tD) of the liquid film separating the colliding bubble from the solid surfaces. With increasing Teflon surface roughness, from ca 1 to 80 µm, the time of the TPC formation was shortened by over the order of magnitude, from ca 100 to a few milliseconds only. At low a-terpineol and n-octanol concentrations, thetTPC values were shorter than in distilled water due to lowering the bubble velocity in the frother presence and diminished bouncing of the colliding bubble. However, at high frothers concentrations the tTPC values were prolonged, despite that the bubble velocity was similar. The prolongation of the tTPC at high frother concentrations indicates that air (micro- and/or nano-bubbles) was present at the Teflon surfaces of different roughness. The mechanism of the tTPCprolongation at high frother dosage is described.

Sep 1, 2012

By Liang Dianyin

In this paper, the molybdenite flotation tailing of cleaner-scavenger bank which has a mass of very fine particles has been taken as raw ore to be processed by flotation with/without ultrasonic. The effect of ultrasonic frequency, intensity, processing time and uploading location on molybdenite flotation efficiency is investigated by four-factor three-level orthogonal experiment, and the effect significances of these ultrasonic variables to molybdenite flotation efficiency have also been evaluated. Single-factor analysis of variance is conducted to investigate whether the effect of ultrasonic on molybdenum ore flotation efficiency is significant or not. The samples extracted from different ore species in different time have been mixed to analyze the particle size. The results show that the particle size of +38µm in concentrate obviously increases while the particle size of -25µmobviouslydecreaseswith ultrasonic, which means that ultrasonic is good for flotation due to sludge removing effect. Keywords: ultrasonic, flotation efficiency, sulfide ore, tailing, grade, sludge removing

Sep 1, 2012

By U. S. Chattopadhyay

The estimated requirement of the nation by the year 2020 is approx. 80 Mt of steel and more than 0.2 million MW installed capacity of the electricity, thereby increasing the consumption of the coking and non-coking coal, which is expected to be in tune of about 75 Mt & 500 Mt respectively. One of the major deleterious factors in achieving the goal is the deteriorating quality of the feed coal used in both steel and power industries. Indian coking coals, in general, are typified by high ash, high inert (both organic and inorganic), low rank, low reactive macerals content, heterogeneous petrographic make-up, inferior coking properties and poor amenability to washing, thereby necessitating suitable washing measure. Coke-based steel industries in India require washed coking coal containing ash % varying between 17-19. The situation demands taking on immediate challenges to fill up the gap between the requirements and supply of coking coal. This paper reviews the R&D attempts in this laboratory and throws light on the key measures as long-term solution to the problem. Search for alternative source of coking coal, like LVC coal and their judicious preparation technology. The low volatile coking coal (LVCC) constitutes about 50% of the total coking coal reserves in India. These coals are characterized by high raw coal ash content (37 to 40%) and very difficult washability potential. If these coals are treated in the existing washeries, which are generally 2 or 3-product systems, the cost of clean coal is high as the byproduct sale value is low. It has been proposed to produce a new type of by product, which enjoys high demand and good coking properties.

Sep 1, 2012

By X. L. Song

A large amount of tailings in concentrators bring a series of problems to the environment and society. It is significant to reclaim the huge tailings and reuse them in industries in order to utilize mineral resources adequately. Primarily Lead-Zinc tailings with a certain quality of clay and feldspar were used to produce ceramic tiles by sintering method under specific technical conditions. By testing the properties of the ceramic tiles, it was shown that the amount of Lead-Zinc tailing used in the tiles was 60%~70%, and the mechanics properties were good. The optimum proportion parameters were Lead-Zinc tailing 60%, clay 35%, feldspar 5%, and the maximum flexural strength of tiles was up to 38.2MPa when it was sintered at 1090? for 30min. Its flexural strength, water absorption and thermal shock resistance reached the State Standard of GB/T4100.4. The product is suitable to be used in pavements and paths of parks.

Jan 1, 2014

By M. Ghiani, P. Massacci, A. Manni, R. Peretti, Center for Mining and Mineralurgical Studies, S. Serranti

"The research study has been devoted to point out the better way to process a colemanite concentrate characterised by a high content of two kind of As sulphides (realgar and orpiment) finely disseminated in the matrix of the boron mineral.Scanning Electron Microscopy analyses have been carried out to determine all the mineralogical constituents and to evaluate their distribution, frequency and mutual relationships.There is a not neglectable part of realgar highly disseminated into the colemanite crystals.The orpiment recurs in small acicular crystals of 20÷30 µm in length and 5 µm in width, very difficult to liberate from the colemanite mineral particles.The colemanite concentrate, in fact, has been addressed to a chemical plant which products were boric acid and gypsum, the contaminated by As. It was unacceptable for further applications and very dangerous if rejected in the environment.Grinding tests under dry and wet conditions have been carried out in order to evaluate the liberation modality of the As sulphide minerals from the colemanite.Some difficulties have been overtaken in order to obtain a selective liberation of the As sulphides from the colemanite even if a certain decreasing in As grade in the higher size classes has been registered.All the comminution products have been analysed by SEM monitoring the liberation degree of the mineralogical constituents.Flotation tests have been carried out after different comminution flow sheet adopting different modulating conditions in order to evaluate the influence of the following parameters:• collector concentration versus contaminants concentration (As minerals) in the froths;• kind and quantity of the frothing agent to maximise the mineral recovery in the froths;• kind and quantity of the modulating agents to maximise the selectivity of the process;• conditioning modalities in order to obtain a suitable dispersion of fines and to avoid segregation of Asbearingparticles together with colemanite ones;• solid/liquid ratio of the pulp to minimise the water flow into the plant."

Jan 1, 2003

By C. Dorfling, P. Albertyn

"Hydrometallurgical recovery of metals from printed circuit board waste typically involves multiple leaching stages; conventionally, base metals dissolution by mineral acids is followed by leaching of gold using cyanide or halide based lixiviants. Alternative lixiviants for gold leaching can reduce the potential hazardous nature of operation. The aim of this study was to investigate the feasibility of using thiosulfate as lixiviant for gold leaching from waste printed circuit boards. Batch leaching tests were performed to investigate the effects of thiosulfate concentration (0.1 – 0.2 M), ammonium concentration (0.2 – 0.4 M), pH (9 – 10.5), solids content (25 – 50 g/L), and copper content of the feed material on the gold leaching behavior. The concentrations of metals in liquid samples were determined by means of inductively coupled plasma atomic emission spectroscopy, and high pressure liquid chromatography was used to evaluate thiosulfate degradation/consumption. The ratio of thiosulfate to ammonia was found to have the most significant effect on the extent of gold leaching, with the best gold extraction observed at a ratio of 0.5 mole thiosulfate per mole ammonia. The lower pH range of 9 – 9.5 generally produced better Au leaching, while low copper extraction during the first stage base metal leaching stages has proven to be detrimental to gold leaching from the residue. Thiosulfate degradation/consumption increased and gold extraction decreased with higher residual copper in the feed. An optimum gold extraction of 78.5 % from base metal leach residue was achieved with 0.2 M thiosulfate, 0.4 M ammonia, and 0.02 M cupric ions at 25°C in the pH range 9 – 9.5.INTRODUCTION Background and Aim The recycling of e-waste is becoming increasingly important as it provides certain economic benefits apart from the obvious environmental benefits. Printed circuit boards (PCBs) are found in most forms of e-waste and contain especially high concentrations of base and precious metals. Hydrometallurgical processes are often considered for the recovery of valuable metals from PCBs; these processes normally implement several leaching stages to selectively recover certain metals."

Jan 1, 2018

By Saeed Farrokhpay

It is known that the grinding condition has a major effect on the beneficiation characteristics of the minerals in subsequent processing, in particular, flotation. In the flotation process, particles surface and their condition can significantly influence collector adsorption and flotation performance. For example, particle shape and its surface roughness occurred during grinding may influence flotation characteristics of a specific ore. In fact, adsorption of different cationic and anionic species on mineral surfaces can be varied depending on the selected comminution procedure. The flotation performance of sulphide minerals can be detrimentally affected by the surface oxidation. The amount of surface oxidation may reduce the hydrophobicity of the mineral and makes adsorption of collectors less selective. Improved liberation may generally result in improved flotation recovery. However, this may result in finer grinding and slimes, and consequently, reduce the overall flotation recovery. This paper discusses the effect of wet and dry grinding on copper flotation of a complex Cu-Pb-Zn ore. Industrially, wet grinding is preferred due to its higher energy efficiency and owing to downstream processing requirements. In this study, series of flotation tests were conducted,and surface analysis (XPS and ToFSIMS) were performed after wet or dry grinding at two different P80 values. Mineralogical study was also conducted to investigate the liberation of valuable minerals after grinding. A higher copper flotation recovery was found for wet grinding. However, the copper recovery was increased by further grinding in both conditions (wet and dry). The results showed a higher collector adsorption on copper mineral surfaces after wet grinding. The surface analysis also revealed that the ore is slightly more oxidized after dry grinding probably due to higher temperature during dry grinding.

Sep 1, 2012

By Z. G. Li

The large-scale vibrating screen has been applied widely in coal industry and other industrial areas as a kind of important device. As vibration mechanical device, it works very hardly and works in very bad environment so that the structure of screen is damaged easily. Therefore, it is very important that how to detect the fault of structure as early as possible to make the repair schedule reasonably and economically and to avoid the body hurt and device damage. As a kind of important structure of vibrating screen, the lower crossbeam is the main carrying structure and it is easily damaged, so it is regarded as a researched object in this thesis and it is tested under the load in the laboratory. Based on the test, acoustic emission wave signals can be got-ten by modern acoustic emission testing technique. Then, the ?wavelet packet - energy? from the characteristics of acquiring signals is used as neural network input vector. In the BP network structure design, the design of a hidden layer with variable number of BP network is established. Based on the error by contrast, the best nerve number can be identified in the hidden layer. Through integrated analysis, using Levenberg-Marquard BP study algorithm, network-training errors are relatively small, the acoustic emission signal is used in BP neural network as a pattern of recognition. In Matlab6.5, neural network model identification is created and taking advantage of nonlinearity and the ability of learning and memory of Neural Network, this model is fixed by training structure of network with training samples. The work presented shows that acoustical emission signal processing and research on early fatigue fault diagnosis based on the wavelet and the neural network is viable.

Jan 1, 2014

By Stephen Simukanga, Jewette Masinja

"Mining has been going on commercially in Zambia for over 100 years. The backbone of the mining industry has been copper production and its by-products of cobalt and gold. Over these years, the mining industry ownership structure has swung from private ownership to state ownership in 1972, and back to private ownership in 1995. Environmental management was first introduced into the body of Zambian legislation in 1991 through the promulgation of the Environmental Protection and Pollution Control Act (EPPCA). The Act’s main functions included the protection of the environment and control of pollution, and in particular to provide for the health and welfare of the people, animals, plants and the environment in general. This Act, was replaced in 2011 by the Environmental Management Act (EMA). The new Act has a number of new elements including: mainstreaming environment in national planning, it provides for the domestication of multilateral environmental agreements, enhances public participation issue, creates a central environmental information depositary, elaborates access to information principles, establishes an environment fund, creates enforcement orders, provides for both Zambia Environmental Management Authority and members of the public to sue for damages following environmental pollution, and provides for the appointment of honorary Inspectors. In addition to this, the Mines and Minerals Act of 1995 provided, for the first time, a section on environmental management in the mining sector. This section also created the Environmental Protection Fund (for mining), and made it obligatory to undertake environmental impact assessment before mining permits could be issued. The Environmental Protection Fund has now been established, as provided for by the law, and currently has more than USD9.0 million in the account. Secondly, environmental auditing is now being carried out annually on mines around the country, the effect of this has been a significant improvement in the environmental management of mining in Zambia. This paper looks at the response of the Zambian mining sector to these pieces of environmental management legislation, and the direction that the mining sector is expected to take on environmental management going forward."

Jan 1, 2014

By Z. Kwela, A. Manhique, W. W. Focke, W. van der Merwe

"The main features of the de Wet improved alkali fusion process for the manufacture of AZST are: Fewer process are steps necessary; radioactivity is removed by leaching rather than by precipitation; fewer waste streams are generated; there is less waste to discard and alkali reagent is recovered in the form of a sodium silicate solution that is essentially free of radioactivity.Here we report on our efforts maximize the alkali recovery in the sodium silicate product stream: Milled zircon, d50 ˜ 9 µm, was fused with caustic soda pearls in open reaction vessels at temperatures between 650°C and 850°C. Fusion times of 1, 2, 4, 24 and 336 hours (with intermittent milling) were investigated. The fusion products were characterized by infrared spectroscopy, X-ray diffraction and by wet chemical analysis.For prolonged fusion times the fusion products approached equilibrium compositions. However, the phases Na2ZrSiO5 and Na4Zr2Si3O12 observed at 850°C did not form at 650°C. Since these compounds do not hydrolyze in water they limit the recovery of alkali in the sodium silicate product stream. For 2-hour fusions a broad spectrum of non-equilibrium reaction-products, that are rich in sodium silicates, is formed."

Jan 1, 2003