Search Documents

By Lina Lopez, Jose Sanchidrian, Manuel Lopez, Pablo Segarra

Previous work in which rock properties and blasting parameters (geometry, charging and timing) were reported together with truck filling times, is taken as a starting point for a thorough analysis of the influence of the former on the mucking velocity. The experimental set was composed by 11 blasts made in an open pit mine. Non-parametric, distribution-free statistics is applied. The mucking rates (in bank cubic meters per unit of bucket volume and per hour) appear to be clearly dependent on the explosive energy and powder factor, both magnitudes combined as energetic powder factor (energy per unit of rock volume). The mucking rate is a non-monotonic function of such factor in the range of the blasts analyzed. The determination of the function is optimum when the fraction of the explosive below grade is not considered and when the explosive energy is qualified as that delivered at a partial detonation regime. Different types of loaders seem appropriate for different energy levels. At low levels both front loaders and rope shovels obtain small productivities without a statistically significant difference in their performance. At high energy levels, front loaders qualify higher than rope shovels. Mucking velocities can be equally small at low energy powder factors and at high ones if rope shovels are involved.

Jan 1, 2008

By Joshua Hoffman, Braden Lusk, Perry Kyle

With the advent of any new technology comes the necessity of fully understanding the mechanics of that technology. The Shock Tunnel is one such technology that provides a cost effective means of simulating large-scale explosions while requiring a fraction of the explosive and space. Although the technique is known and practiced, the dynamics and mechanics of this technology has yet to be fully understood. A relationship between the energy potential of a given explosive and the energy realized at a set of distances was determined. This data was then compared to the energies realized from the same explosive when utilized in conjunction with a shock tunnel. A relationship between potential and realized energy outputs from explosive based shock tunnels exists and the understanding of this relationship would allow all for predictions to be made to forecast a specific amount of explosive required to produce a desired energy output. This energy output should then be relatable to peak pressures produced via the shock tunnel. Two shock tunnels are currently accessible for this study, the first under the direction of the University of Kentucky, and a second under the direction of the Missouri University of Science and Technology. The two shock tunnels differ in dimensions but share common construction materials. Energy realized from a shock tunnel is hypothesized to be a function of the shock tunnel’s dimensions. This study explores how different geometries affect the shock tunnel’s performance; this exploration is broken down into three phases. Phase 1: Open arena testing in which theoretical energies produced by the detonation of small (<1.0 kg) charges are compared to actual experimental values. Phase 2: Shock Tunnel testing in which realized energies are experimentally recorded for the UK shock tunnel. Phase 3: Analysis of the data to lay down the ground work for producing a pressure-forecasting tool given shock tunnel dimensions and explosive characteristics with the possible detection of avenues for optimization of shock tunnels.

Jan 1, 2009

By Lina Lopez, Jose Sanchidrian, Jean Du Mouza, Essaieb Hamdi

This paper evaluates the actual energy delivered by the explosives used in the fragmentation of rock during blasting vs. the available theoretical explosive energy. The evaluation of the fragmentation energy of the blast is first done. Fragmentation by blasting can be seen as a process in which creation of new surfaces within the rock mass is made by generation of new cracks or extension of pre-existing ones. From this idea, the fragmentation blast efficiency can be assessed as the fraction of the available explosive energy used for creation of new surfaces. The evaluation of new cracks area created by the blast is based on the SIMBLOC methodology and the corresponding fragmentation energy is then obtained by the Griffith theory. Secondly, the amount of energy delivered down to a certain pressure or volume along the detonation product expansion process, given by the useful work, is calculated. This is done by first determining the CJ state of the reacted explosive and subsequently performing an adiabatic expansion calculation of the detonation products from that state. W-Detcom code has been used for the calculations using the BKW equation of state with the Sandia parameter set. The fragmentation energy and the useful work are calculated for blasts performed in two mines in Spain. Multiple regression is applied to the results in order to give an assessment of the better description of the explosive energy .

Jan 1, 2002

By Robert Hopler

CHAPTER I. DEFINITIONS AND CLASSIFICATIONS. Definition of Explosives. SECTION 1. The term “Explosive” or “Explosives” whenever used in this ordinance, shall be held to mean and include any chemical compound or mechanical mixture that contains any oxidizing and combustible units, or other ingredients, in such proportions, quantities or packing that an ignition by fire, by friction, by concussion, by percussion or by detonator of any part of the compound or mixture may cause such a sudden generation of highly heated gases that the resultant gaseous pressures are capable of producing destructive effects on contiguous objects or of destroying life or limb, and includes all the articles specifically mentioned in Section 3 herein, and all other similar articles

Jan 1, 2013

By W. Fourney

In the late 70’s and early 80’s in conjunction with other oil and gas well stimulation studies, personnel from the Dynamic Effects Lab performed model testing to demonstrate the effectiveness of utilizing an open section of borehole just before a plug. We called the process stem induced fracturing. The open section beneath the stem was used to increase the pressure magnitude and spread out the duration of the pressure pulse. This technique was later utilized to by Frank Chiapetta (1) in the fracture and fragmentation of rock in quarry blasting situations. He called his technique air deck blasting. In fact, Frank found that the Russians had previously discovered the same technique. There is currently interest in utilizing air deck blasting with an open section of hole beneath the explosive at the bottom of the bore hole to better remove the toe in a fragmentation shot. This paper reviews the development of stem induced fracturing and then describes a series of model tests conducted to measure borehole pressure at points along a borehole when an explosive charge is detonated at the midpoint of the borehole. Tests were conducted in both stiff boreholes (aluminum) and less rigid boreholes (PMMA-Plexiglas). Pressure time profiles were measured at the charge site, midway between the charge and the bottom of the hole, at the stemming at the top of the borehole, and at the bottom of the borehole. Crack initiation sites and crack propagation were also determined in the PMMA models. Some high speed pictures were taken of the event in the PMMA.

Jan 1, 2006

By Calvin J. Konya

Many controversies and differences of opinion exist in blasting technology. The primer location in small diameter dynamite columns is an example of one of these controversial areas. It is generally agreed that in rotation firing of small diameter blastholes, primer placement near the bottom of the borehole is beneficial since it reduces the likelihood of cutoffs. The controversy results in the actual location of the primer in the bottom of the blasthole. Some references indicate that the primer cartridge should be the first cartridge in the bottom of the hole, with the cap pointed toward the collar of the hole. Others indicate that performance is improved with no sacrifice in safety by placing a tamped cartridge first in the hole, and the second cartridge being the primer. The following investigation provides some factual data for consideration.

Jan 1, 1980

By Michael A. Barbaglia, Mark William Withey

The lift shot is an essential blast design in the execution of mine creation and expansion plans. Whether it be opening a new quarry, creating a new level in an existing operation, or for control of water, lift shots are utilized to create the desired results. Lift shots by their nature differ from conventional production blasts because they have no free faces for relief of the blast. Due to this fully confined state, the primary direction of the rock movement is vertical, and the potential for excessive vibration and fly rock generation is great.

Jan 1, 1994

By D. Lee Petersen, Travis Davidsavor

The 2003-2004 expansion of a Duluth medical center required rock blasting adjacent to the existing structures, a Mn/DOT retaining wall and other urban structures. This case history describes the methods of a blast damage assessment, based on blast parameters, excavation locations, and critical vibration receptors (including surgical suites, a linear accelerator and a major retaining wall). The assessment concluded that blast vibrations could be controlled, by limiting charge weight, to eliminate impact at the critical receptors. Prior to construction, we conducted preconstruction surveys on structures susceptible to vibration damage. During construction, we reviewed submittals, observed test blasts, reviewed blasting logs and monitored blasting vibrations. Up to 13 seismographs were used simultaneously. Close coordination with medical center operations personnel was necessary to prevent impacts to critical medical procedures. Measured vibrations were clustered around the predicted values, and attenuated at the predicted rate. High-frequency blast induced ground vibrations induced low-frequency vibration of an adjacent MnDOT retaining wall. Medical center structures were observed to significantly attenuate the ground-borne vibrations. This paper was first published in the Proceedings of the 56th Annual Geotechnical Engineering Conference, 2008, at the University of Minnesota.

Jan 1, 2010

By S Lukovic, Vishwa Bhushan, Calvin J. Konya

Effect of each of these variables has been well characterized for ANFO. This paper presents results of underwater energy measurements for one watergel and one emulsion type of slurry explosive which were initiated by 3 types of initiators (one electric and two cords of different strength) in 2 and 3 inch diameter steel pipes. Results of this 2 x 3 x 2 factorial experiment show the effects of detonating cord on energy released by the watergel and the emulsion explosive. Effect of diameter and its interaction with cord strength have also been characterized for the two explosives.

Jan 1, 1986

By Goran Cirkovic, Zvonimir Ester, Josip Krsnik

During the reconstruction of the motorway Zagreb-Krapina three reinforced concrete bridges were demolished, for their width was not adequate for the new motorway. Demolition of the three bridges was carried out by blasting as duration of the traffic cut on the motorway and the railway was limited to maximally 4 hours. During that period of time the demolished bridges had to be removed. Therefore, very tiny granulation was requested suitable for loading and not endangering the surrounding structures. Before each of three main blasting, trial blasting were carried out including the seismic measurements registering the seismic effects. The nearest residential building was at the distance of less than 30 m from the place of blasting. Additional difficulty was the fact that by each of the three bridges there is a new bridge, with minimal distance between the old and the new bridge being 30 cm. As each of the bridges is of different construction and of various thickness, particular blasting technique has been prepared for each one of the bridges.

Jan 1, 1997

By Tristan Worsey, John Rathbun, Andres Malone

A run of mine, low grade gold heap leaching operation is currently looking to increase ounce recovery by decreasing run of mine fragmentation size. Current blasting practices have resulted in an average fragmentation size of 80% passing 7.05 inches (179 mm). It is estimated that a decrease of 2 inches (51 mm) in the 80% passing fragmentation size has the potential to yield up to a 2.5% increase in the overall life of mine recovery within this ore body. This potential recovery increase could lead to an increase in recoverable ounces which, in turn, would lead to a better profit margin. As this particular deposit is composed of predominantly low grade heap leach the capital investment in a crushing facility was cost prohibitive, it was therefore decided to look into the current blasting practices as a means to improve fragmentation.

Jan 1, 2015

By W C. Burkle

A rather common observation over the last several decades at least has been that rock or ore properties influence blasting results more than does the explosive type that has been used in the blast. It we accept that premise than it is held here that the material to be blasted should receive even closer attention as to its properties. Several years ago, Dr. Richard Ash published papers that pointed out the rock properties that mostly influence blasting. These principles are given attention in this paper. We have gone somewhat further - or lets say expanded this subject in regard to the role of rock structure in open pit blasting. Though open pit work is given some prominence, we believe that much can be observed and applied to underground mining.

Jan 1, 1979

In this paper, the author points out the need to beware of simple time correlations as proof of cause and effect when comparing building cracks and blasting operations. There is a need to be aware of the many other causes besides blasting which affect buildings. Some of these have histories of cyclic behavior; others have a long-term increasing effect on aging and deterioration, often with poorly defined time histories. Many are so strongly site specific that generic relationships are difficult to quantify.

Jan 1, 1981

By Grant Small, Deon Pieterse

Reactive ground conditions at an open pit manganese mine in the Northern Cape of South Africa resulted in an unexpected detonation.

Feb 1, 2020

By Ronald Thomas

The scope of this paper is to examine the growth of safety in an individual and offer new goals in that development. The paper will examine the individual's natural growth and show how it parallels the individual in a safety environment. An individual's new goals for safety include more than the standard accident-free conditions. The new goal strives for a safer working environment where unsafe acts are eliminated through independent knowledge and an individual's growth of interdependency in safety related areas of concern. It will explain how this goal cannot be reached unless driven from the top down in an organization but empowered from the bottom up. Various reference or support organizations will be covered. These organizations deal with safety in mining and explosive use of manufacturing. Other support organizations exist but since this paper is "Back to Basics" only a few major groups will be covered.

Jan 1, 2001

By Thomas C. Jones

The purpose of this paper is to disseminate new information for nonelectric blasting in trenching and construction work. The presentation is not designed or intended to discredit conventional electric detonators or use of MS connectors and cord. Its sole purpose is to inform the S.E.E. of new and exciting benefits realized by the use of the Hercudet non-electric system in the construction industry.

Jan 1, 1984

By Paul Worsey, Robert Sickler

Today, America's mining and construction industries are faced with operating under a condition of reduced profit margins. This makes the implementation of new technology far more sensitive to investment return than ever before. For this reason it is imperative that every effort be made to insure that new equipment and processes be designed to maximize their impact on improved quality, reduction in production cost and enhancement of safety. Using these principles as a foundation, a study was made to evaluate potential automation techniques for the blasting industry.

Jan 1, 1987

By Duane A. Houkom

Down time in the Oil Refining and Petro Chemical Industry is extremely expensive. Each day of non-production may easily cost several million dollars. Explosives have been accepted by this industry to solve many of its problems. Explosives offer a solution which is faster, more economical and most important, safer than many of their methods. Our specialties for these industries include: Refractory removal, industrial cleaning, metal cutting and concrete removal. This report does not include information on concrete removal.

Jan 1, 1982

By James E. Jr Hargroves

With the ever-increasing population growth and modern trend to urban development, the expansion of utilities is a stable, mad or, and constant source of income for many. Blasting is a "necessary evil" to the utility contractor. It can make or break even the most solvent. Housing development expansion and higher treatment of effluents are causing utilities to appear in more congested areas. This paper discusses some of the aspects of utility blasting in the State of Virginia. Consideration is given to bid procedures, pre-blast surveys, record-keeping and practical application.

Jan 1, 1977

By C F. Argo

In the past several years the "Kelly Bar", an innovative device, which incorporates borehole d-rifling and explosives loading into a single detail, has come under scrutiny and criticism. The practical aspects of the Kelly Bar procedure is not questioned, and the system has been highly successful in expediting the loading of explosives in difficult and unstable formations. There have been a number of accidents indirectly associated with Kelly Bar loading and the point in question has become one of safety rather than mechanical feasibility.

Jan 1, 1975