Search Documents

By Finn Ouchterlony, Gert Bjarnholt, Robert Holmberg

A system for contour blasting with a linear shape charge principle has been studied /10/. In one operation the charge creates two notches along the bore hole wall and breaks the rock mass. The built in notching capability makes it possible to reduce the specific charge and the bore hole pressure to 1/3 of what is used in conventional contour blasting and to ensure that cracks are initiated and propagated only at the notches and nowhere else. The notching capability of linear shape charges has been studied experimentally and the bore hole pressure calculated to aid in optimization of a charge for future field experiments in bore holes with a diameter of about 50 mm.

Jan 1, 1983

By Timothy D. Stark

Blasters are usually strictly liable for injury or damage caused by flyrock (trespassory invasion) and blast-induced vibrations (non-trespassory invasion). The application of strict liability to non-trespassory invasions has resulted in significant litigation that has hampered the use of blasting and the blasting industry. Stark (2002) proposes that blasters should not be held strictly liable for non-trespassory invasions but should be liable only if their conduct is proven to be negligent. This change in legal standard was proposed because improvements in blasting technology over the last thirty years allow blasting to be conducted without substantial risk of harm to property and thus the amount of harm imposed by a blast can be related to the level of care exercised by the blaster. It is anticipated that negligence standard will reduce the amount of litigation because a plaintiff will have a greater burden to overcome. To facilitate the acceptance of negligence standard by a court of law, this paper illustrates the application of the negligence and strict tort liability frameworks using actual cases in which a decision was rendered. It is evident from these cases that some of the successful claims under the strict liability framework would not have been successful, and probably not litigated, under a negligence framework, which could result in substantial cost savings to the blasting industry and consumers.

Jan 1, 2004

By William Reisz

In our line of work,like many other professions, there may be times when circumstances or a series of events may arise, contributing toward unacceptable risk. When multiple parties are involved, there will almost inevitably be differences on how best to deal with these situations. Unless approached in an intelligent and these differences may often have the potential for costly and unexpected results.

Jan 1, 2014

By Thomas L. Barkley

This paper describes an unusual design for a 12 foot diameter, 30 foot deep circular shaft shot in a close in urban environment less than 100 feet from occupied structures. It uses diagrams, video footage, and vibration results to describe a 3 deck, 17 hole burn round used to pull 17 feet in one lift.

Jan 1, 1994

By Corry Goumans

Photos 1 - 4 – Chris Elliott is a rock slope supervisor on a construction project east of Seattle, Washington. His job is to look after a “two man” scaling crew working on the rock bluffs some 300 feet in height along the I-90 interstate just east of the town Hyak. The Washington State Rock Engineers noticed a very large mass of unstable rock along the upper rock face and asked us to take it out. Chris is loading explosives in 1½" ” holes that are 8 to 10 feet deep by 40 feet long with 1¼” x 8” power primer on the unstable rock mass that is about 300 feet above the new road construction. I-90 runs east and west longside the new construction note the containment fence and the ship containers along the highway for protection and Lake Keechelus in the background.

Jan 1, 2014

By Jack Eloranta

Building on previous work, this paper expands the template for modeling the economic relationship between blasting and grinding. The actual efficacy of various blasting enhancements is not addressed, however, placing costs and potential benefits in proper context should aid in designing mine/mill optimization trials.

Jan 1, 2014

By Joshua Micah Hoffman, Lifeng Li, Jhon Silva-Castro

Since millisecond detonators were first introduced, at least two variables among others have been more closely considered when timing a mining blast; the accuracy and the precision of the initiation system. Unfortunately, those variables are often ignored when designing timing for mining blast. Despite the lack of consideration of the characteristics of the initiation system, in some situations, e.g., firing a blast hole with one deck and two detonators, changes in the blasting sequence can be the results of the overlapping between blasting charges. The consequences of such overlapping involve flyrock events, fragmentation and diggability problems, and other difficulties affecting the operation of the mine.

Jan 1, 2015

By Malcolm Scoble

The estimation of digging, ripping and blasting requirements in advance of mine production is a difficult task. The characteristics of the superficials and rock mass govern the type and intensity of ground preparation required as a prelude to loading. The incentives for optimum planning of preparation are primarily economic but also relate to mining method and equipment selection, productivity and environmental impact.

Jan 1, 1985

By Yu Yalun, He Jun

Wavelet Analysis is very effective for processing the high-varying signals by its good localization properties. We studied its feasibility of application in the field of blasting seismic signals processing, found the basic representation wavelet for blasting seismic signals analysis, and analyzed a concrete engineering example with analyzing wavelet.

Jan 1, 1997

By Sri R. B Singh

Based on CMRI investigations in nearly 50 mines, the authors have developed two empirical formulae for the effective determination of burden and spacing in any kind of rock deposit. Along with charge loading parameters, decoupling effect and bench height, the equations consider rock characterisation parameter by incorporating 'RQD' i.e Rock Quality Designation. The value of 'RQD' may be obtained either by core recovery using diamond drilling or theoretically from the characteristics of joints or bedding planes. The derived equations may be used in any rock mass under varying geologic and charge loading conditions. The Formulae suggested herein, are explicit, simple in form and easily applicable in field purposes. The values obtained from the present equations are verified against various field data generated by CMRI during the past several years.

Jan 1, 1998

By R Mancini, G Borla

This paper analyses the first results of a part of an EEC research project ("Blasting control for underground mining"). This research that involves three universities (Paris, Torino and Leoben) has been carried out at the Eisenerz test mine in Austria. In the experimental campaign here reviewed, parallel holes rounds have been fired "decomposed", which means with enough delay between the explosions of the successive blastholes groups to allow for a separate evaluation of their effects on the rock. The seismic effects have been recorded by geophones placed at small distance from the blast, the aim being to find out correlations between the features of the seismogram and the good or poor performance of the single blastholes, or of the groups pertaining to the same delay. Indeed, the seismogram is the only safe and cheaply obtainable description of what happens during the blast. The seismogram should be transformed in a diagnostic tool in the round 'calibration' stage, and in a routine control device during excavation.

Jan 1, 1995

By Andrew Stirling

Quarry operators are under constant scrutiny by individual neighbors and neighborhood associations due to the environmental issues arising from daily quarry operations. Issues range from truck traffic, to dust, to blasting induced vibration and noise. Quarry operators and shot service providers employ best practices to minimize disturbances to neighbors. However, these efforts have been limited by the accuracy and flexibility of conventional initiating systems and design techniques.

Jan 1, 2002

By Pat McLaughlin, J R. (Dick) Daniels

Current practice in establishing quarries in remote areas with hilly or mountainous terrain tends to the use of airtracs (or similar pioneering units) drilling horizontal holes to establish a face, followed by bench development with light excavating equipment. The authors propose the use of a hybrid coyote blast design that incorporates long-round tunneling techniques. This method would, in effect, use down-the-hole (DTH) drills to advance the drift cut to the final depth, allowing longer and more rapid drift advances, and replace the cross-cut drifts with clusters of DTH holes to achieve the same explosives distribution.

Jan 1, 1995

By Tristan Worsey, Nathan Rouse, Daykin Schnell

The authors were retained by a proposed underground metals mine operation to evaluate the potential blast vibration amplitudes that could be generated at surface structures above the proposed mine. Literature reviews of published blasting documentation gave little information, data, or models on surface blast vibrations produced by underground mines. At the client’s request, the authors contacted a number of underground mining operations to evaluate interest in sharing blast vibration data with the authors so that the authors could develop an underground-to-surface blast vibration regression equation. The authors worked with three underground metals mining operations to collect surface blast vibration data produced by heading blasts and stope blasts. The data included blast vibration amplitude values, seismograph records, blast design geometry, charge weights, and detonator delay and sequence designs. The total amount of information was used to produce a regression equation and summary dataset that could be used by the proposed underground mining operation to evaluate blast vibration amplitudes that will be generated on the surface. This work is published and presented so that operations with proposed underground mines or proposed underground mine extensions can use these equations to predict vibration amplitudes on the surface above the mine workings before any blasting occurs.

By Michael Wieland

Delay blasting in underground coal generates shock waves and rifting forces that damage charges remaining in the blast pattern. Damaged charges detonate poorly, raise fume toxicity and reduce coal breakage. Such circumstances could be prevented by using explosives resistant to cross-hole interaction damage. The design of rugged explosives is fraught with contradictory requirements, but tradeoffs related to hard-particle size characteristics prove useful. Hard particles, related voids or trapped bubbles represent reaction nucleation centers which strongly influence the performance of coal mine explosives.

Jan 1, 1992

By David Davison, Richard Johnson

Metal-oxidant blends are ordinarily unsuitable as diiect replacements for explosives, because the reaction occurs too slowly. Oxide coatings protect metals, preventing or delaying reaction. By contrast, the electrically-activated reactive composites described below are configured as metal fibers or foils in close proximity to oxidants, with continuous electrical paths from one end to the other. By quickly vaporizing the metal component with an electrical pulse, a reactive composite will be activated, and the reaction will occur rapidly.

Jan 1, 1999

By Thomas L. Barkley, Michael A. Indihar

The new Cyprus Northshore Mining Co. has taken the previous blasting methods of Reserve Mining Co.'s mine in northern Minnesota and adapted them to a new competative Iron Ore Industry. Cyprus was challenged to develop new blasting methods to reduce costs and improve results over the previous mining operation. Many of the older procedures have been kept, but others have been changed in ways that bring the mine operation up to state of the art technology. In addition, unique ideas not previously tried in the North American Iron Ore Industry have been instituted. So far, this has reduced Cyprus's blasting costs by 70 percent.

Jan 1, 1991

By A N: Zditovetsky Shishov, M G. Menzhulin

At present in a building industry demand for products from granite, gabbro and other rocks, steady to erosion, natural and chemical weathering, was essentially increased. It has caused the enlargement of exploitation of stone block deposits and necessity of creation of new technologies of hard stone cut.

Jan 1, 1996

By Dale Nies, David P. Childs

The open pit gold and silver mining operations in the State of Nevada have historically used simple row by row, echelon, or chevron delay patterns. Common practice has been to use detonating cord trunklines and either detonating cord downlines or nonelectric common in-hole delays in conjunction with surface delays. Several operations use a series of downhole nonelectric delays with an entire row loaded with the same delay to develop similar patterns.

Jan 1, 1991

By Erik C. Nygaard

ANFO is the most used industrial blasting agent in the world, and is often used as a reference for comparison of other explosives. It is known to work very well under dry conditions in large borehole diameters, whilst in small bore hole diameters the formation of high amounts of toxic fumes (CO, NO and NOz) can result. In underground blasting, problems can also occur with reduced visibility caused by uncombusted ammonium nitrate.

Jan 1, 1999