Search Documents

By Jerry R. Wallace

Infrastructure improvements and industrial plant expansion and modernization often require rock blasting within 20 feet of existing structures. In many instances trenchlines must cross beneath existing in-serv1ce utility lines.

Jan 1, 1994

By Rowland Jones

This type of quarrying is very much different from that of established quarries in developed countries, demanding somewhat unorthodox techniques to produce the variety of materials required. The demands on the resourcefulness of-the quarrymaster can be very testing, and produces quite a different breed of individual than what is normally met in managerial status in quarries of developed nations.

Jan 1, 1977

By NA NA

None

Feb 6, 2023

By R W. Givens

Comparison tests were performed on 6 emulsion concentrates, 3 microballoon sensitized emulsion concentrates, and 2 water gel concentrates from 8 different sources with ANFO used as a control standard. Variables measured include density, detonation, velocity, detonation pressure, calculated borehole pressure, viscosity, and lead cylinder deformation for blends of 15%, 30%, and 45% concentrate and AN/ANFO blends. Comparative results are presented for detonation velocity vs. deformation, and percentage of inherent air vs. deformation for these blends. It was hoped that these tests would serve as a tool to facilitate the comparison of different manufacturer's concentrates in AN/ANFO blends for equivalent performance characteristics and to help evaluate these products on an equal basis for bid solicitation purposes.

Jan 1, 1990

By J R. "Dick" Daniel

One of the more common tasks in blast management is the adjustment of: shot geometry, explosive energy, and shot timing parameters to achieve changes in blast outcomes and costs. Many of these shot parameters, once a delayed blast is initiated, are modified by the development of new free faces which change the original or static input values to dynamic values. These newly generated dynamic values are easily calculated and find use in fine tuning shot adjustments and in rationalizing blast outcomes in a systematic manner.

Jan 1, 1996

By Bryan Papillon, Karl Christopherson

In order to improve vibrations from quarry blasting, a new technique and timing pattern was established and applied to the particular geology. By shooting a single representative borehole one full second ahead of the production blast, a signature waveform can be isolated and analyzed. Multiple productionsignature blasts were performed. Encroaching residences require quarries to adjust their blasting techniques to reduce vibrations and raise frequencies. A signature hole inherently poses problems to quarries. Blasting one single hole from a production bench poses safety issues to wall stability; vibration issues to close neighbors; and budget issues to the quarry operator. Results showed that the new timing pattern reduced vibrations through timing optimization without a loss in quarry production. Therefore, this technique of vibration analysis employing a production-signature hole is successful in creating a timing pattern that meets the quarry’s goals.

Jan 1, 2008

By Robin L. Simmons

Mining in the Genesis open pit has been conducted above the active haulage and ventilation declines of the Deep Star underground mine. Production has continued in both mines. The Deep Star haulage and ventilation declines, the primary and secondary egresses respectively, had to remain open and safe for travel until the new haulage and ventilation accesses were completed. Eventually, the upper 350 feet in each decline will be removed. The declines are in relatively competent calc-silicate hornfels with several high-angle, northeast-striking, clay-filled or open-spaced fault zones that create localized areas of poor ground requiring steel sets. To maintain the integrity of the declines, blast-induced vibration levels and damage were monitored in both declines after each surface blast. Seven geophones were installed in the declines to monitor peak particle velocity and peak vibration frequency. These data helped design subsequent blasts and predict expected vibration and damage levels. Blast design modifications included reducing the pattern size, reducing the powder factor and limiting blasthole detonations per delay. While limiting blast-induced vibration, these blast design modifications had to allow effective surface mining to continue. Linear regression analysis of peak particle velocity and scaled distance was used to determine the scaled distance necessary to keep the peak particle velocity under 2 inches per second. To date, the new ventilation raise, which is also the secondary escapeway, has been established and safe conditions were maintained in the original ventilation decline. Data collection and conscientious blasting procedures continue above the haulage decline.

Jan 1, 1998

By Robert B. Hopler

Hercules Incorporated has developed and introduced a totally new non-electric delay blasting cap system which utilizes a low energy gas detonation to activate the caps. Unlike any other initiation system, there is no hole-to-hole connection other than empty plastic tubing until the blast is to be set off. Only at that time, when all personnel and equipment are in the clear, is the special gas mixture introduced through the tubing. The actual time of firing is completely under the control of the operator, by pressing the fire button on the blasting machine.

Jan 1, 1977

By Curtis G. Kremer, Jeffrey L. Brummert

Blue Circle Cement's Ravena, New York quarry mines approximately 6.7 million tons of limestone per year. Blasting occurs approximately twice a week on three separate benches. Shots average 60,000 tons but can range up to 140,000 tons. Ongoing scrutiny of the drilling and blasting program allows for maximum blast efficiency which results in lower overall mining and crushing costs. Close cooperation between management and explosives supplier assures Blue Circle Cement's objective, "To develop, implement, and continuously improve a measurable drilling and blasting system that will optimize the total mining and crushing costs while ensuring compliance to safety and maintaining or reducing the environmental impacts of blasting".

Jan 1, 1994

This is the story of a blast - not a large blast by todays standards as it only involved a total of approximately 50 cubic yards of rock. Nor did this blast involve any new or revolutionary blasting technique or require involved analysis or the applications of rock mechanics theories. Instead, it was a blast that involved the tried-and-true principles of good blasting: precise alignment of blastholes; selection of explosives and detonators designed for the conditions encountered; extreme care in loading and hooking up and the use of several ingenious devices and techniques to achieve the proper loading and firing of the blast

Jan 1, 1976

By Alan R. Cameron, Alastair C. Torrance

An explosives underwater test facility has been established and commissioned in the Hunter Valley, New South Wales, Australia which allows the measurement of the actual shock and gas energies of the explosive

Jan 1, 1990

By A. Pope

I have attended two Explosives Engineers’ Conferences in the past 4 years. The first was in Brighton, England with the European Federation of Explosives Engineers in 2005 and the International Society of Explosives Engineers in New Orleans, USA in 2008. At both of these conferences I listened to papers presented on European and English training methodologies and ideologies. As I have been training Shotfirers for the past 18 years in Queensland and the Northern Territory for some 8 years previously, I would like to present our methods of training in Queensland, which I believe is among the best in the world. In Queensland, this training is carried out by a training organisation that is registered by the Department of Education, Training and the Arts under the guidelines of the Australian Quality Training Framework (AQTF). Not only is this Registered Training Organisation (RTO) required to operate under these very comprehensive guidelines, but also those designated by the Explosives Inspectorate of the Queensland Department of Mines and Energy.

Jan 1, 2009

By Agus Setiabudi

East Pit Wira II Project in South Kalimantan, Indonesia with a radius of <500 meters (1,640 ft) from residential has about 454,168 tonnes of coal reserves, with a total remaining reserves of 3,369,383 tonnes (topography per end of June 2011). Thus, reserves may be lost as much as 13.48%. Therefore, it is needed to determine safe blasting technique which meets the Indonesian National Standards (SNI) No. 7571:2012 of vibration threshold, the maximum vibration of 3 mm/s (0.118 in/s) and air blast of 120 dB.

Jan 1, 2014

By Sehoon Lee, Duhwoe Jung, Eunsu Cha, Kyeonghwan Jeong

This case study presents the effectiveness of underground rock blasting to facilitate the trench cut in the hard rock layer using a conventional trench cutter for the construction of a diaphragm wall. Rock blastings are pre-performed up to the scheduled depth and then the fragmented rocks can be easily cut using a conventional trench cutter. Two trial underground rock blastings have been performed and the effectiveness of pre-blasting is presented in terms of a cutting rate, a loss of cutter heads and an amount of overbreak. Based on the results obtained from the trial underground rock blastings, the following conclusions can be appropriate: 1) A pre-blasting of hard rock layer located in depth can help to overcome the limitation of the trench cut using a conventional trench cutter. If the hard rock layer is fragmented after blasting, the fragmented rocks can be easily cut using a conventional trench cutter, 2) The speed of cutting works was accelerated and the loss of cutter heads was significantly reduced in the sections where the blastings were applied prior to cutting. 3) The amount of overbreak, expressed in terms of the amount of poured concrete, can be reduced to some extent. However, the location of blast holes in the trench can also contribute to the amount of overbreak. The closer the location of blast holes to the edge of the trench, the more extensive fractured and cracked zone can be formed on the face of the trench. This can increase the amount of overbreak if the trench is left empty for a while.

Jan 1, 2000

By Frank Huber, Ed Fulop, Neil Singh, Ron Elliott, Blair Gohl, Lewis Clarke

This paper covers the successful application of explosive compaction technology for the densification of the foundation soils for the seismic upgrade of the Seymour Falls Dam, Vancouver, BC. The original earthfill embankment constructed during 1958 to 1961 was upgraded in 2004 to 2007 to withstand the effects of a maximum credible earthquake. This paper provides general background information on the theory of the explosive compaction of soils, history of use, geology of the site, project constraints, explosives selection, blast designs, instrumentation used, problems encountered and solutions implemented, and the results achieved.

Jan 1, 2009

By Calvin L. Cumerlato, David E. Siskind

The Bureau of Mines has monitored structural responses to airblast overpressure produced by munitions disposal at the McAlester Army Ammunition Plant. The Purpose of this study was to determine if the blasting caused vibrations, airblasts or structural responses that could possibly be responsible for cracking or other damage observed in nearby residences. Monitoring took place during a 3-month period at 10 selected residences surrounding the plant. By the end of the monitoring period, nearly 2300 blast-related events had been recorded.

Jan 1, 1994

By Jeffrey W. Lin, Jonathan D. Abbott, Patrick R. Bowden, Tyson J. Plitt

Pentolite is a class of high explosives containing trinitrotoluene (TNT) and pentaerythritol tetranitrate (PETN) with PETN content typically ranging from 40 to 60 wt%. Manufacture involves melting TNT, 80 °C, followed by addition of PETN and trace ingredients to form a homogeneous mixture. Once a mix is ready to be poured, several factors can influence the behavior of the finished product including how long the mix has been at temperature and cooling rate. After the manufacturing process has been completed, storage conditions combined with manufacturing conditions may cause physical changes. Two such changes explored were exudation, liquid exuding from solid boosters, and ratchet growth, irreversible volumetric expansion. Exudation is principally caused by excess water in the process. Ratchet growth is a common phenomenon of nitroaromatic compounds such as TNT where time and temperature fluctuations can cause materials to increase volume, simultaneously decreasing density. Although neither phenomenon affects common attributes such as sensitivity, performance, and shelf-life, both can cause issues in storage and handling. In this study pentolite was cast into various forms under different manufacturing conditions and evaluated over several months of controlled storage conditions including ambient, temperature cycling and elevated isothermal. Subjective and objective measurements were made throughout the evaluation period with the aim to determine the preferred storage methodology.

Jan 21, 2025

By David E. Siskind

In the period 1989 to 1994, the U.S. Bureau of Mines assisted the Office of Surface Mining, Reclamation and Enforcement (OSM) in studying a high-complaint situation near an active surface coal mine. As part of a review for its project report, the Bureau had to address issues on the adequacy of the safe blasting criteria and analysis procedures in its 1980 report RI 8507, Structure Response and Damage Produced by Ground Vibration From Surface Mine Blasting.

Jan 1, 1996

By Kenneth Faroni, Catherine Aimone-Martin, Thomas Gelormino

A blasting improvement program began in 1985 at two traprock quarries in Connecticut to reduce the levels of ground motions and airblast measured at residential structures surrounding the operations. The quarries are situated within town limits, adjacent to a number of historical and other structures. Although blasting vibration amplitudes were found to be far below those that could produce cosmetic defects in structures, they were perceived to be the cause of structural defects observed by homeowners. Based on a comprehensive * review of blasting practices in place during1985, an extensive vibration monitoring program was implemented. The initial study included the instrumentation of selected residential structures to record and analyze strains imposed within structures from quarry blasting, environmental changes, and from daily household activities. A comparison of the results was made with the results reported by the U.S. Bureau of Mines in 1980. The highest strain imposed in drywall from blasting (13 J_I strain) was 12% and 1% of the highest strain levels recorded for normal household activities and temperature changes, respectively. The present philosophy in production blasting is to attempt to keep vibration amplitudes as low as practical by implementing state-of-art blasting control techniques. Currently, blasting seismographs are placed in a circular manner around each quarry, providing production blast vibration records for 360 degrees of coverage at distances of 2500 to 4000 ft. from blasting operations. Seismograph and production blast records are analyzed each year and become part of a Blasting Improvement Plan submitted to the local zoning commission as part of the annual operating permit process. This paper summarizes the results of previous vibration monitoring programs and outlines the modifications made to blasting practices to minimize the levels of ground motions and airblasts. The public relations efforts and standard corporate procedures used by company personnel to address all blast related complaints and alleged damage claims since 1985 are also discussed.

Jan 1, 2000

By R. K. Wharton, G. H. Pickering

The paper reviews the explosives products that have been certified by the different Explosives Notified Bodies for sale in European Union countries. The development of harmonised standards for explosives is also discussed as are recent developments relating to certification and a possible forthcoming Directive on pyrotechnic articles.Copyright

Jan 1, 2004