Search Documents

By Michael Laing

"Geology plays a critical role in many aspects of blasting, from fragmentation to wall control. One often overlooked component of blasting concerns blast results due to the effect of geologic features. The direction of blasting, with respect to strike and dip, can produce varied results, depending on thescenario. Working with geological features, as opposed to against them or without regard to them, can therefore dramatically improve blasting results. This paper focuses on the role of “geologic features”, which include joint-sets, natural fractures, and bedding planes (all of which are commonly referred to as “seams”) for the purposes of this paper. The goal of this paper is to promote understanding and mitigation techniques for various scenarios in which there are identifiable geologic features. Depending on the nature of these features (strike and dip specifically), blast design and pit advancement/development can be carefully considered to use make the best use of these features and optimize blast results."

Jan 1, 2016

By Wang Xuguang, Kang Tingzhang, Zhang Xiaozhi, Wang Guoli, Li Ziqianga

Emulsion powder and granule explosive is produced through airflow fluidization technology by using W/O emulsion. Maintaining the microstructure of W/O emulsion, it has the advantages of both emulsion explosives, such as good water-resistance and detonation properties and powder explosives, such as low cost and east handling. The basic theory of emulsion powder and granular explosive, choices of constituents and formulation, technology for preparation, equipment and relevant parameters, product property as well as technology for safe use have been illustrated in this essay. Based on the above illustration, related factors influencing property and use result have been analyzed.

Jan 1, 2000

By Jan Mehren, Arild Neby

Underwater Tunnel Piercing or Lake Tap, often also called the Norwegian Method, will in many projects be an important part of the hydro electric development scheme. The very last blasting round in the Lake Dorothy Lake Tap Tunnel, which penetrated into the lake at a depth of 120 ft (36 m), was such a key step in constructing the Lake Dorothy Hydroelectric Project. A lake tap project is multidisciplinary. Besides the pure blasting and construction technique aspect, engineering geological and geometric considerations that aim to optimize the tunnel alignment making a lake tap possible at minimized risk are of significant importance. Output data from numerical model analysis of the hydrodynamics resulting from the blasting is vital for the final adjustments to the geometrical layout. The planning of monitoring systems for the surveillance of hydrodynamic impact on valves and pipes as well as control with water levels and air pressures prior to and during the blasting, are all additional crucial elements in the design. More than 600 lake taps have been successfully performed in Norway since the 1890`s. The technique, which deserves to be called well proven, has been applied mostly in the hydropower sector but over the last 20 years also for shore approaches in the oil and gas industry. The demand for this technique seems to be ever more growing.

Jan 1, 2009

By Tyler Rockley, Greg Bailey

This paper is an engineering case study of a blast performed on a highly weathered sandstone isthmus in an area sensitive to vibration and airblast, the challenges associated with such a blast, the methods used to understand rock characteristics, the blast design considerations and a discussion of the blast results. The purpose of the blast was to remove approximately 12 feet (3.7 m) of surface material in order to install a pumping station. The isthmus provided several challenges due to the weathering of the rock and multiple open faces with surrounding water. The highly fractured and weathered rock was subject to about ten years of freeze thaw cycles, influx of water and seasonal submersion. As such, all actual rock conditions were indefinite, including fracturing, rock properties, degradation and competency. The isthmus also had immediate neighbors who were unused to the environmental effects of blasting. To help continue to keep the social license to operate in the area, it was important to reduce the ground vibration, blast duration, dust and airblast. These factors required a better understanding of how the rock would respond to blasting. In order to do this, test blasts were performed on the same geologic formation in a different location of the quarry that was less sensitive to vibration and airblast effects, allowing the blast parameters and design to be verified and refined. The test blasts were performed while monitoring vibration, air blast, material movement and overall shot performance, and the blasting parameters were adjusted accordingly. The isthmus blast was performed based on the final design from these test blasts. The drilling and loading of the shot all met acceptable criteria and were comparable to the test blasts. The blast performance, however, was not as expected; the depth impacted by the blast was substantially more than expected. Since the test blasts were performed in the same formation, but in material that was significantly less weathered than the isthmus, the actual effect of this weathering was the only difference between test blasting and the isthmus blast. Thus, these results can be used for future reference to highlight the effects of blasting such highly weathered rock and help instruct the blast design in similarly complex conditions.

By Alexander S. Escalante, Luis R. Ramirez, Nelson A. Arostegui

Research, analyze, discuss, design, and build an electric oven to perform one of the quality control tests the fanel or common fulminers to determine what temperatures they can detonate at. Give practical applications, conclusions, recommendations and bibliography.

Feb 1, 2020

By Finn Ouchterlony

"Recently detailed fragmentation data from blasts fired with electronic delay detonators (EDDs) in the Red Dog mine in Alaska were presented. They include a comparison with pyrotechnic detonators fordifferent in-­-row delays in a standard pattern and EDDs in an expanded pattern. Fragmentation was measured on the belt after the primary crusher. The Rosin-­-Rammler function (RR, two parameters) was used to describe the crusher product. This was combined with the JK SimMet crusher model and the CZM blast model (Crushed Zone Model, three to five parameters) to estimate a reasonable crusher feed (muck pile fragmentation or run of mine, ROM) for each fitted product. In this way the effect of delay timing and electronic detonators on the median fragment size x50 and uniformity coefficient n for both crusher product and the blasted rock was determined. "

Jan 1, 2012

By Catherine T. Aimone-Martin, Elena Oana Jacobs, Brent Meins

Accurate pressure measurements during underwater detonations are critical for the protection of structures and mitigating impacts to fish and marine mammals. Current guidelines that limit underwater pressures are based on past studies, many of which used sample rates of 48 and 65 kS/s (48,000 and 65,000 samples per second). These sample rates may be insufficient to accurately record high frequency, sharp rise time blast pressures. As such, pressure thresholds associated with fish and marine mammal injury or mortality may be underestimated, calling into question the pressure and sound pressure level guidelines that govern underwater blasting today.

Jan 1, 2019

By Adrian Moore, Alan Richards

A real-time system for prediction of the effect of meteorological conditions on airblast overpressure levels has been established in the Hunter Valley Coalfield in Australia. Real-time meteorological data from continuously operating sounding equipment and a predictive meteorological model is input to an atmospheric refraction model that enables the effect of meteorology on airblast overpressure levels in the area surrounding the blast site to be evaluated. Graphical outputs from the model, which are superimposed over a scaled airphoto of the mine and surrounding area, show the extent that airblast levels will be increased. When combined with inputs that quantify the effect of blasting specifications, the airblast levels that will result in the surrounding area from the combined effect of blasting specifications is determined. The model permits those responsible for blasting to make more accurate decisions on suitable times that blasting may take place to conform with applicable airblast limits.

Jan 1, 2009

By Anders Nordqvist

LKAB operates an underground iron ore mine in Malmberget in the northern part of Sweden. Twelve different orebodies are mined today using both longitudinal and transversal sublevel caving as mining method. The town of Malmberget is located close to the mining area. The need for urban transformation, moving people and houses, is evident for many reasons. The mining methods used have inherent subsidence issues and there are also vibrations from blasting and mine induced seismic events.

Jan 1, 2018

By D Anonby

The Fox Pit at EKATI Diamond Mine is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high faces. Blasting tests were conducted to increase the percentage of benches that meet an 11 m catch width. The subdrill depth for the lower bench trim blasts and the blasthole diameter for the upper bench trim blasts were reduced to maintain the bench crests. Raising the lower trim blastholes by 0.5 m decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. The use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest.

Jan 1, 2007

By Split Engineering Chile Fernando Fernandez

Mathematical modeling in conjunction with mineral characterization is widely used as a method for design and optimization of comminution circuits, to simulate the processes of crushing, grinding and classification. An important input parameter to the simulation models is the Run-of-Mine Particle Size Distribution (ROM PSD). The run-of-mine size distributions due to blasting have a great influence on the performance of a semi-autogenous grinding (SAG) mill. In this paper, a mine case study was conducted where there are four primary geologic units and the material properties between the four units vary considerably. Also, the mixture of the four unit that will be mined at any given time also vary considerably. This presents a challenge in terms of optimizing the blasting for mill production throughout the mine life. As part of the case study, field rock mass characterization, laboratory rock mechanics tests, and laboratory breakage tests were conducted. The field characterization and rock mechanics tests provide material properties used to simulate the effect of different blast designs on run of mine particle size distributions (ROM PSD). The JKSimBlast software was used for these simulations. The rock breakage tests provide material properties used to simulate crushing and grinding performance. The JKSimMet software was used for these simulations.

Jan 1, 2015

By Wayne Rogers, Sarma Kanchibotla, Alan Tordoir, Bryon Bisiauz, Seth Ako, Eric Engmann

Blast induced rock mass displacement can have a significant impact on ore loss & dilution. The mischaracterization of the grade boundaries both prior to, as well as a result of blasting can lead to significant financial losses on account of ore loss and dilution. Ore dilution occurs when waste material is miscategorised as ore and sent for processing diluting the run of mine head grade and recovery. Ore loss takes place when valuable mineral is miscategorised as waste and sent to the waste dumps, thus never being processed and recovered.

Jan 1, 2012

By Jennifer Paukula, Steven Lindsay, S. Joon Kim

String loading is the placement of a bead or ‘string’ of emulsion along the lower edge of a development drill hole. The loading hose extraction rate controls the amount of emulsion placed in each drill hole. This allows a controlled distribution of explosive energy throughout the development round. Center holes are loaded using the slowest extraction rate causing the majority of the explosive energy to be placed in the center of the round. The loading hose is extracted successively faster for the buffer and perimeter holes causing less explosive energy to be placed near the edge of the blast. This causes less damage to the rock mass that remains in place after the development blast.

Jan 1, 2012

By Robert Hopler

INTRODUCTION NOT so very many years ago the farm was about the last place where one would expect to find up-to-date mechanical appliances. Steam, explosives, electricity—the factors which have made the world in general, and America in particular, what it is today— were indispensable for the railroad and the steamboat, the factory and the mine, but the farmer’s work was generally run on a comparatively small scale, and was mostly done by the muscles of men or draft animals. Today, however, the farmer as well as the manufacturer, the contractor and the miner, fully appreciate the value of labor-saving devices. Every up-to date farm, large or small, has modem machinery that tends to reduce the cost of production or to improve farm products.

Jan 1, 2011

By L C. Taylor

Very small scale testing has been shown to be able to predict quite accurately, in many situations, the results of full scale testing. Small scale tests are more cost efficient, easily observed, and easily instrumented than full scale tests. Over the past 10 years small scale testing in the Dynamic Effects Laboratory at the University of Maryland has been used to successfully study the response of structures and soils to explosive detonation. Small scale testing has been successfully used to predict full scale results in underwater cratering and channeling, the loading (both pressures and impulse) on vehicles due to the detonation of buried charges, the positive effects of bottom shaping for military vehicles to reduce this loading, and the movement of obstacles underwater by explosive charges.

Jan 1, 2012

By Lon Santis

This paper describes several applications of quantitative risk assessment in the management of commercial explosives operations. The Institute of Makers of Explosives’ (IME) quantitative risk assessment software modeling program IMESAFR was used for this analysis. Modeled activities include the unloading of a ship at port, locating a safe haven, and dealing with encroachment on a manufacturing facility. The layout of actual explosives sites were used for the analysis. The risk of fatality is analyzed and shown it can be used to make informed operational decisions for each activity. A study of the risks to individuals from activities involving commercial explosives compared to individual risks from other daily activities or exposures is also presented.

Jan 1, 2008

By Italo Onederra, Jason Furtney, Ewan Sellers

The Hybrid Stress Blasting Model (HSBM) is a high level blast modelling research tool which provides results that can still be used implicitly for practical blast design. The code is being developed through an international collaborative research project funded by a consortium of companies which is comprised of explosive, equipment suppliers and major mining houses. A key component of the HSBM is the numerical code and user interface designated as Blo-Up 2.5. To date validation work has focussed on breakage, fragmentation and damage outcomes in controlled laboratory experiments and using large concrete cubes

Jan 1, 2012

By James G. Stuart, Tassilo N. Baur

We will discuss the kind of procedure that we use to predict the no-fire (for safety) and all-fire (for reliability) current levels for any given type electric detonator. The basic idea is to expose several detonators to different levels of electric current, so we can estimate the probability of firing as a function of current. We call this a statistical firing test. But what about the uncertainty in measuring the current? Suppose we are not quite sure what stimulus level we apply? This is the question that we will consider here. This relates to both safety and reliability. Surprisingly enough, we will find that some uncertainty in measuring the levels during our statistical firing test improves our long-term safety and reliability

Jan 1, 2019

By Dal Sun Kim, Michael K. McCarter

"Comminution (crushing and grinding) of rock materials is energy-intensive and expensive. Mucheffort has been directed to improve the efficiency of conventional milling practice, but relatively littleattention has been given to the potential benefits of blast-induced damage on comminution processes. To help assess this effect, research has been conducted at the IRECO Laboratory and the Generic Center for Comminution at the University of Utah. The objective of this research is to investigate the effect of shockinduced “crack-like” damage on rock properties and subsequent breakage efficiency for three petrologically different rock materials under laboratory conditions. In order to evaluate the effect of shockinduced damage, a quantitative measure of rock damage is needed. For this purpose, a scalar variable (0) is proposed."

Jan 1, 1993

By Bill Paysse, Lyle Ruffle

My intention is to produce a video, pictorial, and oral presentation on utility blasting, primarily power pole holes and ditches. Included will be blasting for a take-off structure inside of Wanapum substation, jointly owned by BPA, PSE, and Seattle City Light, and blasting for 230kV steel tower foundations.

Jan 1, 2007