Search Documents

By Joel Warneke, Cristian Caceres, Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2008

By D VanDoorselaere

"Image analysis techniques are widely used for blast fragmentation measurement, and various commercial packages are available for this purpose. These packages are very versatile and serve as a useful tool for optimization of blasting practice. But many times, the results provided by image analysis techniques do not match with sieved and predicted data. This leads to the suggestion that understanding the limitations of this technology is as important as understanding its usefulness and versatility.A study was conducted in two stages:(a) Comparison between the results of image analysis and screened data using laboratory scale muck piles.(b) Comparison between predicted (Kuz-Ram) and measured (Image analysis) blast fragmentation results for several bench blasts.During laboratory work, muck piles with known size distributions were analyzed with the help of image analysis technique. A disparity was observed between the sieved and measured results because the image analysis techniques cannot accurately determine the % of fi nes in the muck. During fi eld work about fourteen blasts were monitored. It was observed that predicted (Kuz-Ram) results rarely matched with measured (Image analysis) results. The Kuz-Ram curves were modifi ed by changing the rock factor so that the Kuz-Ram and Image analysis curves match in the vicinity of the 50% passing size. The pairs of curves (modifi ed Kuz-Ram and Image analysis) were divided into three categories depending upon their differences in the coarse and fi nes ranges. The blast design parameters affecting the difference between the pair of curves have been outlined. The suggestions have been made to better utilize the image analysis system."

Jan 1, 2007

By J T. Keim

Members and guests of the Society of Explosive Engineers, it's indeed a pleasure for a longtime practical user such as myself to have the ears of so many explosive experts for a few minutes just to express my feelings and concerns on blasting as well as the feelings and concerns of many other users and operators.

Jan 1, 1978

By Don Rapp, Rufus Flinchum

Air blast and flyrock are two of the most critical concerns facing the blaster of today. This paper will provide the blaster with proven procedures for recognizing open face and bench surface problems, explain various surveying methods, and provide the mathematical formulas for calculating and designing proper hole placement and explosive load configuration. A concept called "Pattern Footage" is utilized in conjunction with a USBM study to develop blast designs aimed at minimizing air blast and flyrock. In addition to this main focus, this concept can be used in shot displacement and cast blasting design.

Jan 1, 1993

By Travis Davidsavor, Stanley: Dong Vitton

Concrete is a common construction material used throughout the world, and with increasing demand of fast-track construction, blasting and concrete casting are occurring simultaneously at many sites where rock is being excavated for concrete placement. However, there has been significant disagreement in the construction industry as to what intensity of shock vibrations green, or fresh concrete can tolerate. Peak particle velocities are often arbitrarily chosen, or are simply based on materials such as plaster and drywall that have been more thoroughly studied in relation to damage. Previous research on green concrete has used the concrete’s static strength subjected to shockwaves at different ages as the primary damage criteria. In addition, the static strength tests have been based on curing time. However, changes in temperature or humidity can dramatically alter the hydration rate, which affects strength development of different cements. To account for temperature changes and humidity the concept of concrete maturity is commonly used and allows the researcher to see where the concrete was in terms of hydration progress. In general, static testing determines the failure stress that the concrete’s macrostructure can handle, and often failure occurs in the natural materials first or along large defects in casting techniques. Dynamic testing or high strain rate testing, on the other hand, loads materials at such a high rate that larger defects do not have time to react and instead the microstructure is more highly stressed leading to higher strength and stiffness values. This is known as the material’s strain rate sensitivity. Since dynamic testing better tests the microstructural strength, it is believed that it may provide a better way to assess damage to green concrete. Testing includes both static and dynamic compression as well as static and dynamic splitting tensile strength to assess whether damaged has occurred to the concrete. No significant statistical evidence was discovered that damage to the concrete occurred at five different “green” maturities from peak resultant velocities ranging from 10.66 in/s (271mm/s) to 4.40 in/s (112 mm/s) with average intensity of 6.7 in/s (170mm/s).

Jan 1, 2003

By Raimo Vuolio

"Over the past 30 years, the Nordic countries have developed similar practices for estimating damage caused by rock blasting vibrations. However, over the last few years the risk of damage has sometimes been estimated by using international values, which have created unnecessary costs, since they are too conservative. This paper gives a proposal for Finnish blast vibration standards and a calculation model for the extent of the zones for building inspection, risk analysis, and vibration measurements. The international conclusion is that particle velocity is the best descriptor for limiting damage potential for structures. Over 900 000 vibration data recordings from 52971 blasts were collected for this paper during 1970-1989. They show that the most practical description is the vertical component of the peak particle velocity. As rock is a nonhomogeneous medium, it is hard to predict the need and scope of risk analyses, building inspection, and vibration measurements. As a large number of blasts were monitored for the recording of the peak particle velocity in several locations in Finland, and the data combined, it is possible to establish safe scaled distances for the calculation of the need and scope of risk analyses, building inspections, and vibration measurements."

Jan 1, 1991

Fracture Control Blasting is an alternative to pre- and post-splitting or smooth wall blasting. It was developed at the University of Maryland as an attempt to overcome some of the disadvantages that occur with normal blasting practices. There are two main factors that are unique to fracture control blasting. First, it utilizes a notched or grooved borehole to initiate fractures at desired locations and secondly, it employs a very carefully selected charge so as to provide control over borehole pressure. The maximum borehole pressure must be kept between very definite limits in order to obtain initiation of fractures at locations where they are desired and yet not obtain fractures where they are not desired. When coupled with stem induced fracturing, which was developed for oil and gas well stimulation, it has been found that the charge required for fracture control can be as little as 1/40th that required for normal smooth wall blasting. The paper describes the technique of fracture control blasting and gives results of some of the field testing conducted to date.

Jan 1, 1984

By Richard H. Granhom

Detonation pressure, or Chapman-Jouguet pressure, is an intrinsic property of an explosive, and like detonation velocity, is an indicator of explosive performance. Pressure and velocity are also important for calibrating computer codes and for other calculations such as the stress imparted to rock or metal by an explosive. The detonation pressures, P~cj, of many "ideal" explosives have been measured indirectly by recording some hydrodynamic flow variable other than pressure, with P~cj being inferred from hydrodynamics and the assumed Chapman-Jouguet equations. One such method is the difficult and expensive "aquarium technique''.] Commercial explosive manufacturers generally rely on estimates of P~cj generated by computer codes not explicitly designed for non-ideal explosives typically used in commercial applications. Over the last decade, U.S. national and government laboratories have developed in-situ gauge techniques such as the manganin gauge, for direct measurement of detonation pressure. Manganin is an alloy of copper, manganese and nickel, and is ideally suited for use as a pressure transducer because its electrical resistance changes with pressure, but is nearly constant with changes in temperature. A simplified manganin gauge technique adapted for use at a commercial test site is described and some initial results from measurements on commercial emulsion explosives are presented.

Jan 1, 1991

By David Siskind, Mark Stagg

Vibrations from Dade County (Miami area) quarry blasting and structure responses were measured at 11 locations between February and April, 2000, and 10 homes were inspected to analyze the characteristics of their cracking and other damages. These results were combined with information collected by the County and other studies done in south Florida for a blasting impact assessment specific to this area. In addition over 40 quarry blasts in the nine-week monitoring period, about 800 measurements were available from previous monitoring in Dade and neighboring Broward counties. An overall worst-case analyses based on the highest individual amplitudes suggested that vibrations in some areas could have been as high as 0.35 in/s. While amplitudes in the study period were below this value, they were found to be relatively high for the distances and charge sizes. Attenuation with distance is less in Dade County than found elsewhere with quarries having to use scaled distances several times higher than similar sites in the north. Consequently, the vibrations are perceptible at very large distances.

Jan 1, 2001

By Midori Sakamoto, Nobuaki Sakuma, Tsuyoshi Murashita

Recently, tunnel blasting works near the residential area and existing building are increasing and environmental problems caused by vibration have become serious public concern. In order to solve these problems, blasting works have been conducted with segmented blasting and reduce advance per round. However, with these blasting, work efficiency is not obtained, and regrettably the cost and risk of accident tend to increase. We developed a new controlled tunnel blasting technique with electronic delay detonator. Electronic delay detonator can supply extremely large range of delay period which could not be achieved with conventional pyrotechnical delay detonators. We utilized advantages in initiating hole by hole over entire tunnel face at the same round. Much seismic data obtained from tunnel blasting with conventional detonator was statistically analyzed in order to find average duration time of vibration caused by a single hole initiation. Numerical simulation using sample waves from a single hole initiation was carried out in order to find an optimum delay time which can separate vibration in each hole initiation and without decreasing blast performance. Trial blasting was conducted to examine the correctness of optimum delay time obtained from numerical simulation. This blasting technique was applied to an actual tunnel construction. This tunnel is 2 lane automobile tunnel with a total length of 659 meters and internal cross section of 70 square meters. The purpose of the use of blasting technique on occasion, was the protection of fresh water reservoirs directly above the tunnel, and to keep the effect on local private houses to a minimum. The vibration level against this station was limited under 20 mm/see P.V.V. With this blasting, the tunnel construction was completed without exceeding the limited vibration level, with minimum cost and construction time.

Jan 1, 1998

By Jeff Wachendorf

As the title implies, this paper details the start of a cast blasting and the design flexibility required to satisfy different parameters encountered on a large coal mine employing cast blasting as the program has grown and evolved around the town of Colstrip, Montana. As strip ratios have increased, the need to adapt and find solutions to provide coal at a reasonable cost to the mine mouth power plants has risen. Colstrip, Montana has a long history of coal mining which dates back to the early 1920s when Foley Brothers began supplying coal strictly for powering locomotive engines.

Jan 1, 2015

By Mark S. Stagg, Siskind David E

The mining industry occasionally blasts near pressurized transmission pipelines and has requested guidance on safe vibration levels and setback distances. The Bureau of Mines and the Indiana Department of Natural Resources cooperated with AMAX Coal Company on a study of coal mine overburden blasting. Five buried and pressurized 250-ft pipeline sections were specifically installed on the Minnehaha Mine highwall near Sullivan, IN for testing to failure. Four welded steel pipes ranging from 6- to 20-in diameter and one 8-in PVC water supply pipe were monitored for vibration, strain, and internal pressure for a period of 6 months while production blasting advanced up to the pipeline field. In contrast to previous studies of small-scale blasting representing construction activities, these tests involved overburden blasts of up to 2100 lb per delay in 12-1/4-in diameter holes.

Jan 1, 1993

By James Stuart

Explosive components are common in electric power distribution systems. Basically, we use explosives either to open or to close a circuit very quickly, in order to avoid electrical catastrophe. We use explosives in these important applications, because explosive materials are compact, inexpensive, long-lived, powerful, and can be triggered instantly. A lead-alloy fuse will melt when excessive electric current passes through it. A small fuse of this type melts quickly. However, a lead-alloy fuse for high current levels must be larger, and takes longer to melt. Thus, at high current levels, a lead-alloy fuse offers inadequate protection, because electrical catastrophe might happen, before the fuse melts. We need faster-acting, explosive components.

Jan 1, 2009

By John L. Floyd

The use of explosive energy to displace overburden or waste material can provide substantial savings to operations which normally rely on mechanical means for material removal. To optimize the available explosive energy, it is important to quantify the rock's response to the type of explosive and explosive accessories used. During a blast, rock breakage and movement occur so rapidly that the naked eye cannot detect the details of the fragmentation process. A relatively high speed motion picture camera (500 frames per second) can provide the extended time base needed to analyze in detail the site-specific rock response to the explosive detonation. The data of importance to blast casting that can be quantified from these films includes initial face movement, trajectory of rock, and differential face velocities of the material shot. In addition, the ground swell velocities, stemming confinement, and stemming ejection velocity can be determined. The performance of explosive products and delay element accuracy can also be ascertained. The use of high speed motion picture photography and analysis can reduce the number of field trials necessary to maximize explosive performance and increase the benefit provided by blast casting, and in turn, lower production costs. This paper will discuss the methods used for data accumulation and analysis. In addition, three field studies conducted at three separate mining operations will be presented.

Jan 1, 1988

By Park McLure, Paul Kunze

Abandoned underground mine workings have been regularly encountered in open pit mining excavations for many years, for the most part without many serious problems resulting. During the last several years however, some tragic occurrences and near misses have resulted when these old workings were intercepted. This paper will report on the problem as it relates to western open pit mining and will describe several techniques that can be used to identify problem areas before they are reached: Utilization of old maps and engineering data, long hole drilling and probing, and the use of subsurface investigation in the form of ground penetrating radar are the detection methods that will be discussed. The paper will describe some possible actions, once potential problem areas are identified. Drilling and blasting crews are usually exposed to the hazards involved when these situations arise because of their "on the ground" working environment. It is therefore appropriate that some of the best methods of dealing with these hazards once they are identified, seems to involve innovative and creative blast designs. The paper will discuss these approaches and describe an example of this aspect of the solution.

Jan 1, 1993

By Changa-Ha Ryu, Hae-Moon Choi, Sang-Don Lee

The rock mass to be excavated is classified using data obtained from the initial site investigation, and the design of excavation and support is then made based on the rock class. Rock classification provides an empirical design with guidelines for tunnel support compatible with rock mass quality and the method of excavation. Although most clients provide standard patterns corresponding to each rock class, the patterns of drilling and blasting have only been used in estimating the excavation cost and not used in the construction stage. The purpose of the study presented in this paper is to establish a standard blast pattern to yield optimum blasting performance along with an attempt to reduce a difference between design and construction. A series of test blasts were carried out at two tunneling sites of Central Inland Highway crossing the country. Long hole blasting was tested in rock mass whose RMR value is over 60. The blasting results were evaluated by measuring degree of fragmentation, advance rate, muckpile distribution, overbreak, etc. Based on the results of test blast, several patterns were proposed for a twolane highway tunnel.

Jan 1, 2005

By R Frank Chiappeta, Eduardo Nixon, John Dean Smith, Tom Treleaven

"The creation of the Panama Canal was far more than a vast, unprecedented feat of engineering. It was a profoundly important historic event and a sweeping human drama not unlike that of war. Apart from wars, it represented the largest, most costly single effort ever before mounted anywhere on earth. It held the world's attention over a span of forty years. It affected the lives of tens of thousands of people at every level of society and of virtually every race and nationality. Great reputations were made and destroyed. For numbers of men and women it was the adventure of a lifetime.

Jan 1, 1998

By Dale S. Preece

A Discrete element computer program named DMC (Distinct Motion Code) has been developed for modeling rock blasting. This program employs explicit time integration and uses spherical or cylindrical elements which are represented as circles in 2-D. DMC calculations have been compared with measurements on bench blasts in the field with relatively good comparison. Structural geology and joint sets have a significant impact on any blast and DMC has not, until now, included these effects. This paper discusses a recently added DMC capability for treating joints and bedding planes in bench blast simulations.

Jan 1, 1995

By Charles A. Kliche

The Comprehensive Environmental Response, Compensation and Liability Act of 1980 (CERCLA) established a national program for responding to releases of hazardous substances into the environment. The funding mechanism for this program is the Hazardous Substance Response Trust Fund (commonly referred to as Superfund), which provides funding for the implementation of removal and remedial response actions.

Jan 1, 1997

By Ivan Kovac, Pero Marjanovic, Branko Bozic

"The paper deals with results of geophysical survey of the rock masses, and the blasting parameterswhich have effect on the fragmentation in quarries . A relationship between the burden, which is the distance between the charged borehole and the free rock surface, and the velocity of longitudinal waves in the rock mass is established based on measured values for different quarries. It is shown that the drilling geometry can also be detemrined from this relationship."

Jan 1, 1999