Search Documents

By Ronald R. Rollins

A continuous propagation velocity measurement probe has been utilized to determine velocities of slurry explosives, whole prills, crushed prills, aluminized crushed prills, in bulk and plastic screw tubes.

Jan 1, 1984

By Jack Eloranta

This paper documents the relationship between material handling and processing costs compared to blasting cost. The old adage, "The cheapest crushing is done in the pit", appears accurate in this case study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong, inverse correlation with powder factor (lbs powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone.

Jan 1, 1995

By B Mohanty, R Yang, M Leblanc

A total of 33 blasts in the pillar recovery program at INCO-Crean Hill has been investigated by means of an extensive set of diagnostic techniques. These included, borehole deviation measurements, stope cavity survey, near-field seismics in both rock and backfill, in-hole VOD and fragment size analysis. The 200 mm diameter VCR blasts employed a variety of explosives types (ANFO, slurry and ANFO/Polystyrene) and deck sizes. The objective of the investigation was to control dilution and backbreak through optimal choice of explosive type and charge weight, without exceeding vibration limits in the adjacent backfill or causing significant degradation in fragmentation.

Jan 1, 1995

By Karl Ingmarsson

A model for drilling productivity and total drilling cost is presented. It specifically addresses down-thehole drilling, but also covers other drilling methods. The important factors are: 1, productivity in tons drilled; and 2, total cost per drill ton. For non-blasthole applications these factors are measured in drill feet and cost per foot. The model focuses on the entire system and allows the operator to optimize the system based on individual drilling conditions.

Jan 1, 1998

By Paul Worsey, Randall Franklin

This paper is based on an undergraduate research project undertaken for the explosives emphasis in the UMR mining engineering degree program by the first author. The purpose of the selected research topic was to investigate the impact sensitivity of commercial detonators to determine their relative safety for handling and how much abuse they can take without accidentally firing. A modified BAM tester was used for the investigation. Both electric and non electric detonators were impacted at incremental positions along their length to determine the relative effect of their various components. Repeat impact tests were also conducted to see how a damaged cap would react to repeated abuse. The results indicate that it takes a significant amount of impact energy to initiate commercial detonators. They also indicate that repeated abuse can increase sensitivity. Modern commercial detonators appear to be relatively insensitive to impact (an order of magnitude above RDX in the standard BAM test) and this is mainly due to their construction. This explains why damaged caps with exposed powder are more sensitive. Their measured insensitivity correlates with rough handling not being a major cause of blasting accidents.

Jan 1, 2004

By A T. Spathis, J J. Felice, W Klass

Cast blasting has become one of the most efficient ways to move waste rock in open cut coal mining. It is used at Mount Thorley Mine in conjunction with a dragline to move some of the overburden onto the spoil dump.

Jan 1, 1992

By David A. Smith, B L. Jr Lindsey

Arkansas bauxite varies enormously in its consistency and composition which makes blasting a very difficult operation. Blasting rounds have to be designed based on each particular mine's ore characteristics. The variances are so great in some mines that blasting procedures have to be changed almost daily.

Jan 1, 1979

By John W. Kopp, David E. Siskind

Over 4 billion pounds of commercial explosives are used by the U.S. mining industry every year with an excellent and improving safety record. However, accidents involving explosives are seldom minor. They produce a disproportionate amount of fatalities compared to other mining activities, as reflected in the relatively high severity rates. The U.S. Bureau of Mines (USBM) has been analyzing blasting accident data obtained from the Mine Safety and Health Administration (MSHA) to determine the most frequent causes of mine blasting accidents, examining trends in these accidents, and identifying areas of needed research. This paper is an update of three previous blasting accident studies conducted on 4-year intervals by the USBM and published in 1983, 1987, and 1991, and is based on a total of 869 blasting accidents.

Jan 1, 1995

By Donald D. Eilers, Pharis E. Williams, Thomas O. McKnown

The Continuous Reflectometry for Radius vs. Time Experiment (CORRTEX) system was developed by the Los Alamos National Laboratory for determining the energy released in a nuclear explosion by measuring the position of its shock front as a function of time. The CORRTEX system, fielding techniques, and the methods and software for data reduction and analysis were developed over a 15 year period with hundreds of measurements made on nuclear tests and high explosive experiments. CORRTEX is a compact, portable, fast-sampling, microprocessor-controlled system, based on time domain reflectometry, requiring only a 24 volt power source and a sensing element. Only the sensing element (a length of 50 ohm coaxial cable) is expended during the detonation.

Jan 1, 1995

By H Y. Fang, H Sutherland, R M. Koerner

Due to the increased number of complaints by property owners to blasting related industries an apparent need for a clearer understanding of blasting-related damage is needed. We feel that direct structural crack monitoring during such blasts is the appropriate measurement technique. Instrumentation and interpretation of results for taking such measurements are described in this paper. Typical results from blasting and other environmental effects are also described which can eventually be related to Fracture Mechanics principles in the hope of clarifying such disputes in an equitable manner.

Jan 1, 1976

By Tom Donnelly, Roger C. Ilsley

Remote telecommunications seismographs were used to monitor blast vibrations at two historic structures in Cedarburg, Wisconsin during adjacent sewer line construction. The purpose of the vibration monitoring program at the historic structures was to maintain blast vibrations below limiting tolerances established by the Wisconsin State Historic Society.

Jan 1, 1991

By David Sprott

The effect that underground blasting has on the stability of hangingwalls, pillars and other rock structures is an inherent part of Noranda's geomechanics and mine design program to improve mine safety and stability, increase productivity and reduce ore dilution. The blast monitoring program at Noranda Research aims to provide values of particle velocities and accelerations, delay firing times, and vibration periods to assist with practical blast design and controlled blasting techniques.

Jan 1, 1988

By Virgil L. Lewis

On September 7, 1994, a Burlington Northern coal train crashed into a parked train in the downtown Gillette, Wyoming rail yard. I would like to address two issues in regards to this accident. One, a slide presentation of the damage created by the accident and the resulting required clean-up and two, a simulation of "what if" had there been an explosion during the course of the crash.

Jan 1, 1996

By E Emery Jr Gray

A need for more delay periods other than those normally manufactured throughout the explosives industry rarely occurs. This paper will discuss one such incident from an analytical view through practical application.

Jan 1, 1976

By B Mohanty

Several parameters such as, Energy, Strength, Brisance, Impulse, and Bubble Energy, are in common use in the explosives industry today to rate commercial explosives in terms of blasting performance. However, this multiplicity of terms, their frequent interchange and their purported one-to-one correlation with expected performance have given rise to a considerable amount of confusion, and have often resulted in unrealistic rating of explosives. In this paper, various theoretical and experimental methods of estimating energy and performance of explosives are discussed and their relative merits examined. These methods include, Computer Code Calculations, Cylinder Test, Trauzl Test, Ballistic Mortar Test, Underwater Test and Model-scale blasting. It is shown, in the light of actual blasting process, that such measures cannot be considered accurate indicators of expected blasting performance as the properties of rock to be blasted are either totally ignored or only partially accounted for in these methods. It is also shown that no single technique alone among those currently employed by the explosives industry can lead to realistic rating of explosives in terms of expected blast results. The need for the adoption of a two-tier rating system, one based on chemical potential "energy", and the other based on blasting "performance" is proposed, and specific approaches to achieve this objective are outlined.

Jan 1, 1981

By Tom Short, Bill Beam

Some of the weapons testing shafts at Mercury, Nevada require depths of 1000ft and diameters of 10 feet. The top 40 feet to 65 feet is drilled, blasted and excavated by Large caisson type augers in order to provide vertical working room for the placement of large, oil field type, drilling rigs and the required drill collar.

Jan 1, 1991

By Evan Smart, Andrew Palangio, David Klingspor, Blessing Taiwo

This study presents a DMAIC-based approach to optimize blasting performance and achieve crusher-compatible fragmentation at the Walker-Severn Quarry in Ontario, Canada. By applying the Six Sigma DMAIC (Define, Measure, Analyze, Improve, Control) framework, the study aims to enhance the integration between blasting and primary crushing operations. Several representative blasts will be simulated and evaluated using both aerial and terrestrial image analysis technologies to assess fragmentation characteristics. The investigation was guided by quarry-specific Key Performance Indicators (KPIs), ensuring that blast design modifications were both practical and operationally relevant. Through structured analysis and data-driven refinement of blast parameters, the study reveals how this framework was used to address the quarry production demand for increased crusher throughput, and reduced processing costs. The existing quarry blast design was assessed as a baseline and compared against the crusher's inlet requirements and the acceptable fines level specified by the quarry. This evaluation aimed to identify and implement modifications to enhance blast performance. A drone (UAV) was employed to capture post-blast images and monitor blast pile displacement. These UAV images were used to generate an orthomosaic image, which was analyzed to assess fragmentation. The orthomosaic was overlaid onto a GIS platform using a 10m-by-10m grid to evaluate fragmentation distribution across the bench and identify areas requiring optimization. Additionally, drone imagery was utilized to monitor the impact of each blast on the subsequent blast's free face and to assess energy utilization for optimizing front-row holes to achieve improved fragmentation. The outcomes of this research offer a replicable methodology for continuous improvement in quarry blasting practices, with a focus on producing fragmentation that aligns with primary crusher requirements.

Jan 26, 2026

"Recently, an effort was made to calibrate the Riedel-Hiermaier-Thoma (RHT) material model to reproducethe behavior of granite under impact and explosive loading conditions. The study concluded that the materialmodel captured the phenomenon of compressional damage in granite due to such loading conditionsfairly well. The present work uses hydrodynamic modeling with the calibrated RHT model to estimate thefines generated around a blasthole. This can improve the calibration of different size-distribution empiricalmodels and enhance the prediction of fines."

Jan 1, 2012

By Roger L. Keller

This paper covers the design and test blast procedures for several drop shafts and edits leading to the completion of a recent Rochester Pure Waters Expansion Project . Due to the projects "in-town" presence, and its close proximity to many sensitive vibration sites, very stringent ground vibration limitations and guidelines for blasting were places on each site.

Jan 1, 1991

By John C. Didlinger, John L. Didlinger

As we begin the pre-blast survey we need to decide on the number of holes needed for production and a detailed highwall inspection. The survey consists of checking the highwall and placement of barrier cones. At the Elmhurst Chicago Stone Company, Barbers Corner Plant, we use 18-24" orange highway type safety cones. These cones are easily noticed because of their high visibility color in all weather conditions and are placed approximately 20-25 feet from the face and approximately 50 feet apart along the highwall, then the area is checked for back break, under cut, over hang, surface filled area and clay area. This deposit is unique because of the number of clay filled areas and slip seams that meanders through the deposit plus a fault that runs North-Northwest and South-Southeast. This particular limestone deposit is overlaid with glacial sand and gravel and the top weathered stone wanders plus or minus 10 feet in 1400 feet.

Jan 1, 1996