Search Documents

By R J. Roach, D Roy

After months of discussion on ways and means to improve productivity in the shaft sinking process, it was decided to look at those areas where, historically, methods have been stagnant for many years. These categories included drilling, hole diameter, drill patterns, explosive types, explosive loads, initiation techniques, cut design, wall control, fragmentation and heated magazines.

Jan 1, 1997

By Michael S. Wieland

The stress waves generated during delay blasting in underground or surface mines not only fracture the surrounding coal, rock, or other strata, but also impact delayed charges remaining in neighboring boreholes. This crossing wave interaction is a ubiquitous fundamental damage mechanism, ultimately responsible for numerous occurrences of misfires and flyrock. The hazards and waste from wave-induced malfunctions are Just the recognized tip of the iceberg. Undetected marginal performance of damaged delay detonators and desensitized charges poses a tremendous unresolved problem, resulting in the reduction of mining profits and the certain retention of unwanted risks.

Jan 1, 1988

By Mark S. Stagg, Steven V. Crum

The Bureau of Mines is conducting research to develop methods to control fragmentation and improve productivity in surface mine blasting. As part of this research, PRONT02D, a two-dimensional finite element computer program developed at Sandia National Laboratories, was employed to model the fragmentation produced from RS-50, a single hole, reduced scale bench blast in a massive dolomite. The fragment size distribution obtained from the computer simulation was calculated using a submodel that utilizes the crack density and nominal flaw size values computed by PRONT02D.

Jan 1, 1989

By Alan R. Cameron, William W. Forsyth, Tom H. Kleine

In the production environment, the current limits of blasting are most often defined by the ability of the operator to drill blastholes from a planned collar location to the required toe location. Many problems which are initially described as deficiencies in blasting or support are directly related to drilling. The assessment of support performance and blasting efficiency must begin with a detailed examination of drilling practices.

Jan 1, 1995

By J Paul Tidman, Stephen H. Chung

One of the requirements in open pit gold mines is to minimise the mixing of ore and waste. Dilution can be reduced by choke blasting and control of the initiating sequencing. The authors have used the DMC computer model (developed at SANDIA) to examine the effects of timing and charge distribution on ore dilution. The model has been calibrated by measurements of vertical uplift derived from high speed videos made at the Dome Super Pit in Timmins.

Jan 1, 1997

By Rahim G. Haghighi, Calvin J. Konya

Fragmentation is the fundamental concern of rock blasting, serving as a measure of blasting effectiveness. Fragmentation is sensitive to the inter-relationship among the design variables which define pattern geometry. Therefore, the objective of this study was to develop a model which represented a confined bench blast and to investigate the movement of burden-rock as the length to burden (L/B) ratio was varied.

Jan 1, 1985

By Sally Lynn Zadra

"In May, 1994, Echo Bay Minerals - McCoy/Cove Mine petitioned for approval to recycle used oil formanufacturing ANFO. Recycling oil in this way will result in a cost savings for the minesite as well ashaving a positive environmental effect The petition has met the approval of the Bureau of LandManagement, the Nevada Department of Environmental Protection, and has received tentative approval from the Mine Safety and Health Administration."

Jan 1, 1996

By Ettore Contestabile, Cameron Thomas

Implosive-type electrical/mechanical connectors such as XECONEX have been used extensively for joining electrical transmission lines. This implosive action of explosives has also been applied to other forms of high energy metal working with excellent results. However, as with many other products, the inherent blast energy of these units has caused some environmental concerns especially when used in proximity to inhabited areas.

Jan 1, 1995

By J MacPhail, H Gardner

This paper discusses reasons why users of rotary air blast hole bits encounter premature bit failure due to bearing failure. It also discusses a lubrication system designed for rotary rock bits to combat bearing failure.

Jan 1, 1996

By J R. Brinkmann

The South African gold mining industry presently uses four different types of explosives in stope blasting. There is general agreement that the type of explosive has considerable effect on Important blasting results such as the degree of rock fragmentation, the intensity of damage to surrounding rock, and the success of break-out at the toe of the hole.

Jan 1, 1989

By Lyle Avey

For the purpose of this paper, testwork and general pre-splitting practice will be discussed for the Chimney Creek Mine.

Jan 1, 1990

By Yoshiharu Tanaka, Keita Morooka, Masaaki Yamamoto, Katsuhiko Kaneko

Smooth blasting is the standard method for underground rock excavation, to reduce over break and remaining rock damage. We already utilized the high accuracy of the electronic delay detonator to investigate its effect on over break remaining rock damage, and surface smoothness. And we presented at 11th annual symposium on Explosives and blasting Research.

Jan 1, 1998

By S A. Steyn, I P. Douglas

Duvha Opencast is a large South African dragline operation supplying coal to the Duvha Power Station which is operated by Eskom, the state power utility. For Duvha to remain competitive with other collieries, it has proved necessary to continuously examine and investigate methods of reducing costs. With explosives representing a major portion of the total working costs, blasting is an obvious area of investigation.

Jan 1, 1991

By Leslie Taylor, Kevin Genson

This paper reports on an experimental study of the effect that bottom shaping might have on the impulse delivered to a light armored vehicle due to a buried mine detonating beneath the center of it. The study was restricted to explosives buried in saturated sand and three parameters were varied within the study: bottom angle (0 degrees to 21 degrees), depth of burial of the explosive (1.02 mm to 12.7 mm), and stand off distance (0 mm to 38.1 mm). Six hundred and thirty six milligrams of explosive was used as the explosive load. It has been shown in previously published work [1,2] that Hopkinson scaling works well for the determination of impulse loading on a semi-rigid target plates. Therefore in terms of a full scale test using 4.54 Kilograms of explosive the parameters investigated would cover a DOB of from 19.56 mm to 243.84 mm and a Stand off distance from 0 to 734.06 millimeters. These values nicely cover those of interest to the Marines with regard to the AAV (amphibious assault vehicle). Four angles were investigated at all DOB’s and Stand off distances – 0 degrees, 7 degrees, 13 degrees, and 20 degrees. The results show that reduction in impulse delivered to the target is achieved with an angled bottom on the target plate with a major reduction occurring before the 13 degree angle is reached. Hence vehicles with quite modest bottom angles could help greatly in load reduction with very little loss in utility.

Jan 1, 2008

By Brian Stump, D. Craig Pearson

This work quantifies seismic coupling as a function of charge weight for single-fired (simultaneously detonated) explosions observed in the mine and at regional distances. These single-fired explosions are contrasted to standard production shots from the same mine. Production shots include cast blasts to remove overburden and coal shots for fragmentation. The blasts were conducted in a mine in NE Wyoming. The data sets consist of measurements in the mine (100-10,000 m) and at regional distance (360 km) using a seismic array near Pinedale, Wyoming (PDAR). The single-fired explosions ranged in designed size from 5,500 to 50,000 lbs. Peak amplitudes measured at a single element of the regional array are modeled by a power law relation dependent on explosive weight. Scaling constants were determined for each of the dominant regional phases: b(Pn) = 0.84±0.14; b(Pg) = 0.84±0.09; b(Lg) = 0.91±.08. Spectral ratios of observations from different explosions observed at the same station illustrate the frequency dependnce of the source scaling relations. Spectral ratios of in-mine observations are consistent with those of regional data. The observed single-fired ratios are well replicated by Mueller-Murphy source model ratios. The data and model illustrate both the increase in long-period spectral level and the accompanying decrease in source corner frequency with increasing charge weight. The coal and cast blasts that make up the production shots ranged in size from 77,000 to 4,738,230 lbs. The peak amplitude (1-20 Hz) for the largest delay-fired production shot (4,738,230 lbs.) is comparable to that of the largest single-fired explosion (50,000 lbs.). This comparison can be explained in terms of destructive interference between waveforms from individual boreholes introduced by delay firing. Shot specific models of delay firing suggest that peak amplitudes in this same frequency band for the production shots are insensitive to the total amount of explosives in the blast. Peak amplitude data at regional distances supports his modeling result.

Jan 1, 2002

By Brad Johnson

Homestake Mining Corporations' open cut operation at Lead SD. experienced a highwall failure in October of 1993. The failure released a 75' section of rock wall at the 5280' level. It came to rest on the 5200' safety bench. Since work was in progress below the failure, this rock had to be removed for safety.

Jan 1, 1995

By Mike Koehler

An underground mine that produces aggregate limestone was in operation for approximately eight years when geological changes resulted in dangerous rock falls. The roof in the mine was not bolted; therefore, the drilling and blasting program was called upon to maintain roof integrity. Drilling and blasting were analyzed and modifications were adopted to stabilize the roof. Initial changes were made in the drilling equipment, drill pattern, explosive type, and timing. Any amendments made, after the initial phase, were made individually so it would be easy to discern which changes worked.

Jan 1, 2002

By Advanced Initiation Systems Inc

10 years in R&D Last 5 years available commercially Worldwide Met strict approvals for manufacturing and use

Jan 1, 2004

By Doug Hoy

The scope of the Cliff Avenue Reconstruction Project in Sioux Falls, South Dakota was to widen a two lane highway to five lanes, along with removing and reconstructing both above and below ground utilities located along the project limits. The objective of this paper is to present the blasting techniques used in the rock excavation phase of the Cliff Avenue Reconstruction Project.

Jan 1, 1992

By Graeme Exelby

The 4" Wassara water hammer was originally developed by G-Drill AB together with Swedish Mining Company LKAB for their underground long hole production drilling. Sandvik Rock Tools AB is responsible for the introduction of Wassara worldwide.

Jan 1, 1998